Low dielectric thermoset. II. Synthesis and properties of novel 2,6‐dimethyl phenol–dipentene epoxy

A 2,6‐dimethyl phenol–dipentene adduct was synthesized from dipentene (DP) and 2,6‐dimethyl phenol, and then a 2,6‐dimethyl phenol–DP epoxy was synthesized from the reaction of the resultant 2,6‐dimethyl phenol–DP adduct and epichlorohydrin. The proposed structures were confirmed by Fourier transform infrared, elemental analysis, mass spectra, NMR spectra, and epoxy equivalent weight titration. The synthesized 2,6‐dimethyl phenol–DP adduct was cured with 4,4‐diamino diphenyl methane, phenol novolac, 4,4‐diamino diphenyl sulfone, and 4,4‐diamino diphenyl ether. The thermal properties of the cured epoxy resins were studied with differential scanning calorimetry, dynamic mechanical analysis, dielectric analysis, and thermogravimetric analysis. These data were compared with those for the bisphenol A epoxy system. The cured 2,6‐dimethyl phenol–DP epoxy exhibited a lower dielectric constant (ca. 3.1), a lower dissipation factor (ca. 0.065), a lower modulus, lower thermal stability (5% degradation temperature = 366–424 °C), and lower moisture absorption (1.21–2.18%) than the bisphenol A system but a higher glass‐transition temperature (ca. 173–222 °C) than that of bisphenol A system. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4084–4097, 2002     

Synthesis and characterization of novel low‐dielectric cyanate esters

For the purpose of increasing the mobility of residual bisphenol A dicyanate ester (BADCY) during the final stage of curing and achieving a complete reaction of cyanate groups, a small quantity of monofunctional phenol was added to BADCY to form an imidocarbonate, or a small quantity of monofunctional cyanate esters was added to form cyanate ester copolymers. The proposed structures were confirmed with Fourier transform infrared, elemental analysis, mass spectrometry, and NMR spectroscopy. The thermal properties of the cured cyanate esters were measured with dynamic mechanical analysis, thermogravimetric analysis, and dielectric analysis. These data were compared with those for the cured BADCY resin. The cured modified cyanate esters exhibited a lower dielectric constant, a lower dissipation factor, and lower moisture absorption than the cured BADCY system. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2589–2600, 2004     

Synthesis of photosensitive and thermosetting poly(phenylene ether) based on poly[2,6‐di(3‐methyl‐2‐butenyl)phenol‐co‐2,6‐dimethyl‐phenol] and a photoacid generator

A chemically amplified photosensitive and thermosetting polymer based on poly[2,6‐di(3‐methyl‐2‐butenyl)phenol (15 mol %)‐co‐2,6‐dimethylphenol (85 mol %)] ( 3c ) and a photoacid generator [(5‐propylsulfonyloxyimino‐5H‐thiophen‐2‐ylidene)‐(2‐methylphenyl)acetonitrile] was developed. Poly[2,6‐bis(3‐methyl‐2‐butenyl)phenol]‐co‐2,6‐dimethylphenol)] ( 3 ) with high molecular weights (number‐average molecular weight ～ 24,000) was prepared by the oxidative coupling copolymerization of 2,6‐di(3‐methyl‐2‐butenyl)phenol with 2,6‐dimethylphenol in the presence of copper(I) chloride and pyridine as the catalyst under a stream of oxygen. The structures of 3 were characterized with IR, ¹H NMR, and ¹³C NMR spectroscopy. 3 was crosslinked by a thermal treatment at 300 °C for 1 h under N₂. The 5% weight loss temperatures and glass‐transition temperatures of the cured copolymers reached around 420 °C in nitrogen and 300 °C, respectively. The average refractive index of the cured copolymer ( 3c ) film was 1.5452, from which the dielectric constant at 1 MHz was estimated to be 2.6. The resist showed a sensitivity of 35 mJ cm^?2 and a contrast of 1.6 when it was exposed to 436‐nm light, postexposure‐baked at 145 °C for 5 min, and developed with toluene at 25 °C. A fine negative image featuring 8‐μm line‐and‐space patterns was obtained on a film exposed to 100 mJ cm^?2 with 436‐nm light in the contact‐printed mode. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 149–156, 2005     

Synthesis,characterization, and properties of novel epoxy resins and cyanate esters

We synthesized a novel epoxy (dopotep) and cyanate ester (dopotcy) based on a phosphorus‐containing triphenol (dopotriol). The proposed structures were confirmed by IR, mass spectra, NMR spectra, and epoxy‐equivalent‐weight titration. The synthesized dopotep or dopotcy was copolymerized with diglycidyl ether of bisphenol A (DGEBA), 6′,6‐bis(3‐phenyl‐3,4‐dihydro‐2H‐1,3‐benzoxazineyl)methane (F‐a), or dicyanate ester of bisphenol A (BADCY). Thus, copolymers based on DGEBA/dopotep/diphenylmethane (ddm), F‐a/dopotep, BADCY/dopotcy, and DGEBA/dopotcy were developed. The thermal properties, dielectric properties, and flame retardancy of these copolymers were investigated. The curing kinetics of dopotep/ddm and dopotep/diamino diphenylsulfone were studied with differential scanning calorimetry. The microstructure of DGEBA/dopotcy was studied with IR. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3487–3502, 2006     

Thermostable cyanate ester resins and POSS‐containing nanocomposites: influence of matrix chemical structure on their properties

Thermostable densely crosslinked cyanate ester resins (CER) with different chemical structures, derived from monomer dicyanate esters of bisphenol E (DCBE), bisphenol A (DCBA), hexafluorobisphenol A (6F‐DCBA) or from cyanated phenol‐formaldehyde oligomer PT‐30, and the nanocomposites based thereon, with 0.01 to 10 wt% epoxycyclohexyl‐functionalized polyhedral oligomeric silsesquioxane (ECH‐POSS), were synthesized and characterized by means of dynamic mechanical analysis, differential scanning calorimetry, far‐infrared, and creep rate spectroscopy techniques. As shown, thermal and mechanical properties increased in a row of matrices prepared from DCBE < DCBA < 6F‐DCBA < PT‐30. Thus, these matrices with T_g = 248, 275, 300, and ~400°C (DMA, 1 Hz), respectively, had dynamic modulus E′ values of 1.8, 2.7–3.0, and 3.6 GPa at 20°C; high rigidity (dynamic modulus of about 1–2 GPa) retained at temperatures up to 200°C for DCBE matrix, 250°C for DCBA and 6F‐DCBA matrices, but up to 380°C for PT‐30‐based matrix. The maximal effects from introducing ECH‐POSS nanoparticles, covalently embedded into CER network, were attained mainly at their ultra‐low contents (<<1 wt%); however, the ECH‐POSS impact decreases in a row of matrices prepared from DCBE > DCBA > 6F‐DCBA > PT‐30. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis and properties of a cyanate ester containing dicyclopentadiene(II)

A 2,6‐dimethyl phenol‐dicyclopentadiene novolac (DCPDNO) was synthesized from dicyclopentadiene and 2,6‐dimethyl phenol, and the resultant DCPDNO was reacted with cyanogen bromide into 2,6‐dimethyl phenol‐dicyclopentadiene cyanate ester (DCPDCY). The structures of the novolac and cyanate ester were confirmed with Fourier transform infrared spectroscopy, elemental analysis, mass spectrometry (MS), and nuclear magnetic resonance. For the purpose of increasing the mobility of residual DCPDCY during the final stage of curing and achieving a complete reaction of cyanate groups, a small quantity of a monofunctional cyanate ester, 4‐tert‐butylphenol cyanate ester (4TPCY), was added to DCPDCY to form the cyanate ester copolymer. The synthesized DCPDCY was then cured with 4TPCY at various molar ratios. The thermal properties of the cured cyanate ester resins were studied with dynamic mechanical analysis, dielectric analysis, and thermogravimetric analysis. These data were compared with those of the commercial bisphenol A cyanate ester system. Compared with the bisphenol A cyanate ester system, the cured DCPDCY resins exhibited lower dielectric constants (2.52–2.67 at 1 GHz), dissipation factors (0.0054–0.0087 at 1 GHz), glass‐transition temperatures (261–273 °C), thermal stability (5% degradation temperature at 406–450 °C), thermal expansion coefficients (4.8–5.78 × 10^?5/°C before the glass‐transition temperature), and moisture absorption (0.8–1.1%). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 671–681, 2005     

Preparation of phosphinated bisphenol from acid‐fragmentation of 1,1,1‐tris(4‐hydroxyphenyl)ethane and its application in high‐performance cyanate esters

We reveal a route for the preparation of phosphinated bisphenol, 1,1‐bis(4‐hydroxyphenyl)‐1‐(6‐oxido‐6H‐dibenz <c,e> <1,2> oxaphosphorin‐6‐yl)ethane (2) , via a one‐pot reaction of 1,1,1‐tris(4‐hydroxyphenyl)ethane and 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐oxide (DOPO) in the catalysis of p‐toluenesulfonic acid. A two‐step reaction mechanism, acid‐fragmentation of 1,1,1‐tris(4‐hydroxyphenyl)ethane followed by nucleophilic addition of DOPO, is proposed for the synthesis. Based on (2) , a dicyanate ester derivative, 1,1‐bis(4‐cyanatophenyl)‐1‐(6‐oxido‐6H‐dibenz <c,e> <1,2> oxaphosphorin‐6‐yl)ethane (3) was prepared and co‐cured with a commercially available dicyanate ester, the dicyanate ester of bisphenol A (BACY). Experimental data show that incorporating (3) into BACY enhances the flame retardancy and dielectric properties with little penalty to the thermal properties. A thermoset with T_g 274 °C, coefficient of thermal expansion (CTE) 49 ppm/°C, D_k 3.04 (1 GHz), T_d (5%,) N₂: 435 °C, air: 424 °C, and UL‐94 V‐0 rating can be achieved via this approach. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Synthesis and characterization of new phosphorus and other heteroatom containing aryl cyanate ester monomers and networks

Several aromatic dicyanate monomers have been synthesized bearing para-linked strong electron withdrawing groups, such as phenylphosphine oxide, sulfone, and carbonyl. These groups increased the reactivity of the cyanate functional groups and eliminated the need for curing catalysts. However, an undesirable decrease in the processing window between the monomer melting point and the onset of cure was also generally observed. An arylene ether phenyl phosphine oxide system was designed that displayed several attractive characteristics such as a low softening point, a wide processing window, cure with no catalyst, high T_g and high char yield in air, suggesting that these new thermosets might show good fire resistance. The dicyanate ester monomers were synthesized in high yield by reacting various bisphenols with cyanogen bromide in the presence of triethylamine. The high reactivity of the cyanate functional groups required that the cyanation reaction be conducted at temperature below 0°C in order to prevent imidocarbonate side reactions. Proton NMR and FT-IR were used to characterize these monomers. The cyclotrimerization curing process was monitored by the disappearance of the carbon-nitrogen triple bond stretch (2270 cm⁻¹). An optimal cure schedule was determined and the cured polycyanurate networks were characterized by DSC, DMTA, and TGA. Tg values were typically > 250°C and 5% weight loss values were observed by TGA in air above 400°C. Several of the dicyanate monomers with sufficiently large processing windows were cured into single lap shear adhesive bonds onto titanium 6/4 and the measurements are reported herein. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 977–987, 1997     

Further study of the viscoelastic phase separation of cyanate ester modified with poly(ether imide)

In this study, the viscoelastic phase separation process was studied further by time‐resolved light scattering, differential scanning calorimetry, and scanning electron microscopy in the system of poly(ether imide)‐modified bisphenol‐A dicyanate. It was observed that the evolution time of phase structure and relaxation time of diffusion flow of the bisphenol‐A dicyanate were similar with the phase diagram of curing conversion versus content of PEI. The results suggested that the viscoelastic phase separation was affected by the curing conversion of the system at the onset point of phase separation. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 517–523, 2006     

Flame retardant polycyanurate thermosets from the cyanate esters of triphenylphosphine oxide

Three cyanate esters containing phosphorus are synthesized in good overall yields starting from bromoanisoles. Di‐ and tricyanates with meta configuration are most stable while para is less so. The para dicyanate ester isomer is particularly affected by water from the atmosphere. The meta dicyanate ester 2 has good thermal properties with glass transition at 268 °C and char yield of 65% in air at 600 °C. All three phosphorus‐containing cyanate esters are low flammability in an open flame. They make highly combustible cyanate esters resins less flammable simply by blending. Mixing 10 wt% dicyanate ester 2 into bisphenol A or E dicyanate esters makes them rate V‐0. Published 2018.^† J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1100–1110     

Polycyanurate networks from anethole dimers: Synthesis and characterization

Novel biorenewable bisphenols are obtained through simple and rapid chemical transformation of the natural product trans‐anethole. The corresponding dicyanate esters are thermally cured to give polycyanurate networks. The thermal properties from differential scanning calorimetry, thermogravimetric, and dynamic thermomechanical analyses of the new dicyanate esters compare favorably with similar commercial products. © 2012 Wiley Periodicals, Inc.^? J Polym Sci Part A: Polym Chem, 2012     

Molten state reactivity of difunctional cyanates: Thermal and spectroscopic studies by liquid and solid CP-MAS 13C-NMR

Using differential scanning calorimetry, we have investigated three difunctional cyanate monomers differing by their central group: bisphenol A dicyanate (BADCy), bisphenol E dicyanate (BEDCy), and hexafluorinated bisphenol A dicyanate (BAFDCy), to determine the effect of the central group on the molten state reactivity of heat-treated cyanates. To identify the different phenomena occurring during the heat cycle, which was followed by differential scanning calorimetry, ¹³C-NMR (liquid and solid) was undertaken. This technique was used to characterize the major products and side products formed. Using ¹³C-NMR and HPLC, we were able to detect the formation of compounds with a triazine ring at one chain end and a hydroxyl function at the other. The presence of the latter depended on the purity of the initial monomers. In light of the purity parameter, inherent in the synthesis of the products, we propose an order of reactivity, at molten state, of the polymerization of the three cyanate monomers in the temperature range of 180–300°C. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1245–1254 1997     

High performance toughened cyanate ester resin with low injection temperature for RTM process

A high‐performance modified cyanate resin system with low injection temperature for fabricating advanced composites via resin transfer molding (RTM) was developed, which was made of bisphenol A dicyanate ester (BADCy) and diallyl phthalate (DAP). The processing characteristics, mechanical, and thermal properties of the resin were studied, and the effect of the content of DAP on the processing and performance parameters was discussed. The results show that the processing properties of the modified cyanate system are dependent on the content of DAP. All the formulations studied in this paper have good processing characteristics; their injection temperatures are between 30 and 40°C and the pot life is about 20 hr at 50°C. The cured resins exhibited good thermal stability, excellent toughness, and good hot–wet resistance, suggesting that the toughened cyanate resin is a potential high‐performance RTM matrix for advanced composites. Copyright © 2008 John Wiley & Sons, Ltd.     

Synthesis and characterization of unsymmetrical benzonitrile‐containing polyimides: Viscosity‐lowering effect and dielectric properties

A new unsymmetrical diamine, 2‐(3‐aminophenoxy)‐6‐(4‐aminophenoxy)benzonitrile (3,4‐APBN), is synthesized via two consecutive S_NAr reactions and the temperature‐dependent reactivity of the fluorides in 2,6‐difluorobenzonitrile, whose first S_NAr reaction occurs at 70 °C and second, at 100 °C, allowing timing control of reaction sequence and circumventing the transetherification side reaction. Thus, a series of polyimides (PIs) is prepared from the polymerization of 3,4‐APBN with five common dianhydrides (6FDA, DSDA, OPDA, BTDA, and PMDA). For comparison, a second series is also prepared from two symmetrical diamines ([2,6‐bis(3‐aminophenoxy)benzonitrile (3,3‐APBN) and 2,6‐bis(4‐aminophenoxy)benzonitrile (4,4‐APBN)] and 6FDA or PMDA. The processability of the poly(amic acids) (PAAs), for the first series is greatly improved since their solution viscosities are much lower than PAAs based on symmetrical diamines. Besides having high glass‐transition temperatures (249–332 °C), and thermal stability [5% weight loss in the range of 505–542 °C (air) and 512–546 °C (nitrogen)], these PIs form tough, transparent and flexible films that have a tensile‐strength range of 82.1–121.3 MPa, elongations‐at‐break of 5.33–9.81%, and tensile moduli of 2.11–2.97 GPa. Their film dielectric constants are 3.08–3.62 at 10 kHz, moderately higher than that (2.92) of analogous PI (CP2) without nitrile groups. Overall, we found that the reduction of structural symmetry in repeat units can improve the polymer processibility as well as increasing their dielectric constants. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4998–5011     

Synthesis and properties of alternating copolyamide‐imides based on 2,6‐bis(4‐aminophenoxy)naphthalene and comparison with its related isomeric polymers

A series of novel polyamide‐imides III containing 2,6‐bis(phenoxy)naphthalene units were synthesized by 2,6‐bis(4‐aminophenoxy)naphthalene and various bis(trimellitimide)s in N‐methyl‐2‐pyrrolidone (NMP) using triphenyl phosphite and pyridine as condensing agents through direct polycondensation. The polymers were obtained in quantitative yield with inherent viscosities up to 1.53 dL/g. Most of the polymers showed good solubility in NMP, N,N‐dimethylacetamide, N,N‐dimethylformamide, and dimethyl sulfoxide and could be solution‐cast into transparent, flexible, and tough films. The films had tensile strengths of 84–111 MPa, elongations at break of 8–33%, and initial moduli of 2.2–2.8 GPa. Wide‐angle X‐ray diffraction revealed that most polymers III were amorphous. The glass‐transition temperatures of some of the polymers could be determined by differential scanning calorimetry traces, recorded at 247–290 °C. The polyamide‐imides exhibited excellent thermal stabilities and had 10% weight loss at temperatures in the range of 501–575 °C under nitrogen atmosphere. They left more than 57% residue even at 800 °C in nitrogen. A comparative study of some corresponding polyamide‐imides is also presented. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2591–2601, 2001     

High‐performance poly(ethylene‐2,6‐naphthalate) fiber prepared by high‐tension annealing

A high‐tension annealing (HTA) method has been applied to zone‐annealed poly(ethylene‐2,6‐naphthalate) (PEN) fibers in order to further improve their mechanical properties. The HTA treatment was carried out under an applied tension of 428 MPa at a treating temperature of 175 °C. The applied tension was close to the tensile strength at 175 °C. The resulting HTA fiber had a birefringence of 0.492 and degree of crystallinity of 57%. Wide‐angle X‐ray diffraction (WAXD) photographs of the HTA fibers showed three reflections (010, 100, and 1 10) attributed to an α form crystal, but no (020) reflection attributed to a β form was observed in the equator. The tensile modulus and tensile strength increased with processing, and the HTA fiber had a maximum modulus of 33 GPa, a tensile strength of 1.1 GPa, and a storage modulus of 33 GPa at 25 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 61–67, 2000     

Synthesis and properties of aromatic poly(ester amide)s with pendant phosphorus groups

Two series of phosphorus‐containing aromatic poly(ester amide)s with inherent viscosities of 0.46–3.20 dL/g were prepared by low‐temperature solution polycondensation from 1,4‐bis(3‐aminobenzoyloxy)‐2‐(6‐oxido‐6H‐dibenz〈c,e〉〈1,2〉oxaphosphorin‐6‐yl)naphthalene and 1,4‐bis(4‐aminobenzoyloxy)‐2‐(6‐oxido‐6H‐dibenz〈c,e〉〈1,2〉oxaphosphorin‐6‐yl)naphthalene with various aromatic diacid chlorides. All the poly(ester amide)s were amorphous and readily soluble in many organic solvents, such as N,N‐dimethylformamide, N,N‐dimethylacetamide (DMAc), and N‐methyl‐2‐pyrrolidone (NMP). Transparent, tough, and flexible films of these polymers were cast from DMAc and NMP solutions. Their casting films had tensile strengths of 71–214 MPa, elongations to break of 5–10%, and initial moduli of 2.3–6.0 GPa. These poly(ester amide)s had glass‐transition temperatures of 209–239 °C (m‐series) and 222–267 °C (p‐series). The degradation temperatures at 10% weight loss in nitrogen for these polymers ranged from 462 to 489 °C, and the char yields at 800 °C were 55–63%. Most of the poly(ester amide)s also showed a high char yield of 35–45%, even at 800 °C under a flow of air. The limited oxygen indices of these poly(ester amide)s were 35–46. © 2002 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 459–470, 2002; DOI 10.1002/pola.10129     

New poly(amide–imide) syntheses. XXI. Synthesis and properties of aromatic poly(amide–imide)s based on 2,6-bis(4-trimellitimidophenoxy)naphthalene and aromatic diamines

A novel polymer-forming diimide–diacid, 2,6-bis(4-trimellitimidophenoxy)naphthalene, was prepared by the condensation reaction of 2,6-bis(4-aminophenoxy)naphthalene with trimellitic anhydride (TMA). A series of novel aromatic poly(amide–imide)s containing 2,6-bis(phenoxy)naphthalene units were prepared by the direct polycondensation of the diimide–diacid with various aromatic diamines using triphenyl phosphite (TPP) in N-methyl-2-pyrrolidone (NMP)/pyridine solution containing dissolved calcium chloride. Thirteen of the obtained polymers had inherent viscosities above 1.01 dL/g and up to 2.30 dL/g. Most of polymers were soluble in polar solvents such as DMAc and could be cast from their DMAc solutions into transparent, flexible, and tough films. These films had tensile strengths of 79–117 MPa, elongation-at-break of 7–61%, and initial moduli of 2.2–3.0 GPa. The wide-angle X-ray diffraction revealed that some polymers are partially crystalline. The glass transition temperatures of some polymers could be determined with the help of differential scanning calorimetry (DSC) traces, which were recorded in the range 232–300°C. All the poly(amide–imide)s exhibited no appreciable decomposition below 450°C, and their 10% weight loss temperatures were recorded in the range 511–577°C in nitrogen and 497–601°C in air. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 919–927, 1998     

Synthesis and properties of novel phosphorus‐containing thermotropic liquid crystalline copoly(ester imide)s

A series of novel phosphorus‐containing polyesterimides were prepared from diols—a mixture of a new aromatic phosphorus‐containing bisphenol, namely 1,4‐bis[N‐(4‐hydroxyphenyl)phthalimidyl‐5‐carboxylate]‐2‐(6‐oxido‐6H‐dibenz<c,e><1,2>oxaphosphorin‐6‐yl)‐naphtalene, with aliphatic diols such as 1,3‐propanediol, 1,4‐butanediol, 1,5‐pentanediol, 1,6‐hexanediol, and 1,12‐dodecanediol—and an aromatic diacid chloride containing two preformed ester groups, namely terephthaloyl‐bis‐(4‐oxibenzoyl‐chloride), via high‐temperature polycondensation in o‐dichlorobenzene. The structures of monomers and polymers were verified by means of Fourier transform infrared (FTIR) spectroscopy and ¹H NMR spectroscopy. The molar ratio of aromatic bisphenol to aliphatic diol was varied to generate a series of copolyesterimides with tailored physicochemical properties, structure–properties relationships being established. The effect of the phosphorus content on the thermal properties and the flame retardancy was evaluated by means of thermogravimetric analysis (TGA), TGA–FTIR, and scanning electron microscopy. The polymers were stable up to 340 °C showing a 5% weight loss in the range of 340–395 °C and a 10% weight loss in the range of 370–415 °C. The char yields at 700 °C were in the range of 13.6–38% increasing with the content of phosphorus‐containing bisphenol. The effect of the aliphatic content on the liquid crystalline behavior was investigated by polarized light microscopy, differential scanning calorimetry, and X‐ray diffraction. The transition temperatures from crystal to liquid crystalline melt were in the range of 209–308 °C. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Processing,mechanical properties,and fracture behavior of cereal protein/poly(hydroxyl ester ether) blends

Blends of poly(hydroxy ester ether) (PHEE), a recently developed bisphenol A ether‐based synthetic biodegradable thermoplastic polymer, with a soybean protein isolate and two hydrolyzed wheat glutens were studied. Blends of the proteins with PHEE were produced from 20 to 70% by weight of protein content. Young's moduli of the protein/PHEE blends fall in the range of 0.8–1.5 GPa with tensile strengths ranging from 10 to 30 MPa. Critical stress‐intensity factors of the blends ranged from 2 to 9 MPa‐m^1/2 depending on the amount of protein added. Morphological analysis indicated a moderate degree of adhesion between the protein and PHEE phases in the blends. In general, as the protein content was increased the materials lost ductility and failed in a brittle manner; however, the mechanical properties of several compositions were comparable to commercial thermoplastics such as polystyrene. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2324–2332, 2002