Synthesis and properties of polyimides derived from 9,10‐dialkyloxy‐1,2,3,4,5,6,7,8‐octahydro‐2,3,6,7‐anthracenetetracarboxylic 2,3:6,7‐dianhydrides

A series of new polyimides containing alicyclic units and alkyloxy side chains were prepared from 9,10‐dialkyloxy‐1,2,3,4,5,6,7,8‐octahydro‐2,3,6,7‐anthracenetetracarboxylic 2,3:6,7‐dianhydrides and various aromatic diamines. Their physical properties and structures were investigated. Polymers were obtained with inherent viscosities of 0.24–0.53 dL/g. In comparison with the aromatic polyimides, most polymers were readily soluble in common organic solvent such as N‐methylpyrrolidone and m‐cresol. These polymers had glass‐transition temperatures between 111 and 296 °C depending on the structure of the repeating unit and 10% weight‐loss temperatures of 418–477 °C in nitrogen. Wide‐angle X‐ray diffractometry for as‐polymerized samples revealed very low crystallinity and layered structures, which were better developed in the polymers with longer side chains. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1764–1774, 2002     

Amphiphilic mesogen‐jacketed liquid crystalline polymers: Design,synthesis, and self‐assembly behaviors

We synthesized a series of amphiphilic mesogen‐jacketed liquid crystalline (LC) polymers with a biphenyl side‐chain mesogen containing a carboxylic acid group on one side and an octyloxy group on the other, and the number of methylene units between the biphenyl core and the exterior carboxylic acid group was varied to adjust the mesophases and the amphiphilic nature. The polymers were obtained through conventional radical polymerizations and characterized by a combination of different techniques such as thermogravimetric analysis, differential scanning calorimetry, polarized light microscopy, and X‐ray scattering. The results revealed that the polymer without any methylene spacer, POBP‐0C, did not exhibit LC properties while POBP‐1C (n = 1) and POBP‐7C (n = 7) formed double layer smectic A (S_A) phases. The hydrogen bonding among the carboxylic acid groups and the segregation between the carboxylic acid groups and the alky chains played important roles in forming the mesophases. In addition, the solution self‐assembly behaviors were also preliminarily investigated through the fluorescent probe technique and transmission electron microscopy, and vesicles with uniform sizes were observed. The weak hydrophilicity and large degree of freedom of the carboxylic acid group and the relative rigidity of the polymer chain due to the “jacketing” effect were responsible for the formation of the structures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

High‐molecular‐weight side‐chain liquid‐crystalline polyethers based on 4′‐cyanobiphenyl‐4‐oxy mesogenic groups

A set of poly[ω‐(4′‐cyano‐4‐biphenyloxy)alkyl‐1‐glycidylether]s were synthesized by the chemical modification of the corresponding poly(ω‐bromoalkyl‐1‐glycidylether)s with the sodium salt of 4‐cyano‐4′‐hydroxybiphenyl. New high‐molecular‐weight side‐chain liquid‐crystalline polymers were obtained with excellent yield and almost quantitative degree of modification. All side‐chain liquid‐crystalline polymers were rubbers soluble in tetrahydrofuran. The characterization by ¹H and ¹³C NMR revealed no changes in the regioregular isotactic microstructure of the starting polymer and the absence of undesirable side reactions such as deshydrobromination. The liquid crystalline behavior was analyzed by DSC and polarized optical microscopy, and mesophase assignments were confirmed by X‐ray diffraction. Polymers that had alkyl spacers with n = 2 and 4 were nematic, those that had spacers with n = 6 and 8 were nematic cybotactic, and those that had longer spacers (n = 10 and 12) were smectic C and showed some crystallization of the side alkyl chains. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3002–3012, 2004     

Phase structures and transition behaviors in polymers containing rigid rodlike backbones with flexible side chains. V. Methylene side‐chain effects on structure and molecular motion in a series of polyimides

A series of organo‐soluble hairy‐rod polyimides was recently synthesized from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA) and di[n‐alkyl]‐4,4′‐diamino‐6,6′‐dibromo‐2,2′‐biphenyldicarboxylate with side chains of varying lengths (the numbers of methylene units), BACBP(n). Dynamic mechanical (DM) results reveal two cooperative relaxation processes for BACBPs(n > 10), which correspond to the two (low‐ and high‐) transition temperatures observed in differential scanning calorimetry (DSC). For BACBPs(n < 10), although two DM relaxation processes can be observed, the low‐temperature relaxation peak shifts into a medium temperature region that is difficult to observe in DSC experiments. Measurements indicate that the density of BACBP(n)s decreases with increasing numbers of methylene units. A discontinuity in the rate of density change can be seen at BACBP(10). Variable temperature solid‐state nuclear magnetic resonance experiments were also carried out to determine the molecular origins of each of the observed DM relaxation processes. The low‐ [for BACBPs(n > 10)] and possibly the medium‐ [for BACBPs(n < 10)] temperature relaxations are associated with the onset of motion in the side chains, and the high‐temperature relaxation is associated with motion in the backbones. Wide‐angle X‐ray diffraction analysis indicates that the lateral packing periodicity of the backbones in the unoriented polyimides changes its relationship with the side‐chain length at around 10 methylene units. In the oriented films of these polyimides, furthermore, those having the long side chains [BACBPs(n > 10)] adopt monoclinic unit cells, whereas those having the short side chains [BACBPs(n ≤ 10)] possess hexagonal unit cells. The drastic temperature difference between the low‐ and medium‐relaxation processes observed in DM experiments may be explained because of a change in the lateral packing arising from the variation of the side‐chain length. The limited mobility afforded the BACBPs(n ≤ 10) is a result of their more ordered conformation and interdigitation between the neighboring side chains. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1633–1646, 1999     

Synthesis and characterization of spirobifluorene‐based polyimides

The synthesis and properties of organosoluble aromatic polyimides, containing spiro‐skeletal units in the polymer backbone on the basis of the spiro‐diamine monomer, 2,2′‐diamino‐9,9′‐spirobifluorene, are described. In the case of the spiro segment, the two fluorene rings are orthogonally arranged and connected through a tetrahedral bonding carbon atom, the spiro center. As a consequence, the polymer chain is periodically zigzagged with a 90° angle at each spiro center. This structural feature minimizes interchain interactions and restricts the close packing of the polymer chains, resulting in amorphous polyimides that have good solubility in organic solvents. Compared with their fluorene‐based cardo analogues, the spirobifluorene‐based polyimides have an improved solubility. Furthermore, the main‐chain rigidity of the polyimide appears to be preserved because of the presence of the spiro structure, which restricts the free segmental mobility. As a result, these polyimides exhibit a high glass‐transition temperature (T_g's) and good thermal stability. The T_g's of these polyimides were in the range of 287–374 °C, and the decomposition temperatures in nitrogen for a 10% weight loss occurred at temperatures above 570 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3615–3621, 2002     

Synthesis of new aromatic polyimides with various side chains containing a biphenyl mesogen unit and their abilities to control liquid-crystal alignments on the rubbed surface

New poly(m-phenylene 4,4′-oxydiphthalimide)s containing various side chains, such as 6-(4-biphenylmethoxy)hexyloxy group and 6-(phenylphenoxy)hexyloxy isomers, were synthesized, giving thin films of a high quality. All the polyimides apparently were almost amorphous, but exhibited short-range ordering in some extent, depending on the side chains. By incorporating side chains, the thermal properties, including stability, thermal expansivity, and glass transition temperature, were generally degraded, whereas the optical and dielectric properties were improved. All the polyimides exhibited a good rubbing processability and excellent performance in the controlling of both the alignment and the pretilt of LC molecules in the LC cell. The pretilt angle of LC molecules was easily achieved in a wide-angle range of 8–27°, depending upon the rubbing density as well as the incorporated side chains. The pretilting of LC molecules was very sensitive to all the molecular parameters (namely, the flexibility of polymer chain backbone as well as the isomeric structure of biphenyl mesogen end group, spacer length, and spacer conformation in the side chain) in the polyimide, in addition to the rubbing process. In particular, the side chains, which are much shorter in length than the long alkyl side chains in the polyimides being used widely as LC alignment layers, were evident to involve effectively in the alignment of and the pretilt of LC molecules, which are highly desired in the LC display industry. This might mainly be attributed to a strong interaction between the biphenyl mesogen end group of the side chain and the LC molecule. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2909–2921, 1999     

Synthesis and properties of soluble trifluoromethyl‐substituted polyimides containing laterally attached p‐Terphenyls

A new fluorinated diamine monomer, 2′,5′‐bis(4‐amino‐2‐trifluoromethylphenoxy)‐p‐terphenyl, was synthesized from the chloro‐displacement of 2‐chloro‐5‐nitrobenzotrifluoride with the potassium phenolate of 2,5‐diphenylhydroquinone, followed by hydrazine palladium‐catalyzed reduction. A series of trifluoromethyl‐substituted polyimides containing flexible ether linkages and laterally attached side rods were synthesized from the diamine with various aromatic dianhydrides via a conventional two‐step process. The inherent viscosities of the poly(amic acid) precursors were 0.84–1.26 dL/g. All the polyimides afforded flexible and tough films. The use of 4,4′‐oxydiphthalic anhydride and 2,2′‐bis(3,4‐dicarboxyphenyl)hexafluoropropane dianhydride produced essentially colorless polyimide films. Most of the polyimides revealed an excellent solubility in many organic solvents. The glass‐transition temperatures of these polyimides were recorded between 254 and 299 °C by differential scanning calorimetry, and the softening temperatures of the polymer films stayed in the range of 253–300 °C according to thermomechanical analysis. The polyimides did not show significant decomposition before 500 °C in air or under nitrogen. These polyimides also showed low dielectric constants (2.83–3.34 at 1 MHz) and low moisture absorption (0.4–2.2%). For a comparative study, a series of analogous polyimides based on the nonfluorinated diamine 2′,5′‐bis(4‐aminophenoxy)‐p‐terphenyl were also prepared and characterized. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1255–1271, 2004     

Synthesis and properties of photoalignable aromatic polyesters containing phenylenediacrylate units in their backbones and n‐alkyl moieties in their side groups

A series of poly[oxy(4‐n‐alkyl‐3,5‐benzoate)oxy‐1,4‐phenylenediacryloyl]s (PPDA‐CnBZ polymers) with high molecular weights was synthesized. These polymers exhibit excellent solubility in some common organic solvents and produce good quality films using conventional spin‐casting and drying processes. The polymers are thermally stable up to 357–362 °C in a nitrogen atmosphere; their glass transition temperatures are greater than 121 °C. The photoreactions and photoalignments of the polymers were investigated using ultraviolet‐visible and infrared spectroscopy, and their liquid crystal (LC) alignment properties were examined. The phenylenediacrylate (PDA) chromophores in the polyesters were found to mainly undergo photocyclization upon ultraviolet light irradiation. Irradiation of the polyester films with linearly polarized ultraviolet light (LPUVL) induces preferential orientation of the polymer main chains, while the unreacted PDA chromophores are aligned along the direction perpendicular to the electric vector of the LPUVL. All the films irradiated with LPUVL were found to align LCs in a direction perpendicular to the electric vector of the LPUVL. Moreover, these LC alignments persisted even on irradiated films annealed at temperatures up to 210 °C, which is much higher than the glass transition temperatures of the polyesters. These LC alignment characteristics are due to the anisotropic interactions of the LC molecules with the oriented polymer chains and with the unreacted PDA chromophores. LC alignments on the polyester film surfaces have homeotropic to homogeneous characteristics, depending on the length of the n‐alkyl side group, providing strong evidence that the n‐alkyl side groups of the polyesters play a critical role in determining the pretilt angles of the LCs. The LC pretilt angles were also found to be influenced by the thermal annealing history of the irradiated films. In summary, the excellent properties of the PPDA‐CnBZ polymers make them promising candidate materials for use as LC alignment layers in advanced LC display devices. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1322–1334, 2004     

Synthesis of polyethylene oxide graft polysilylenes and networks based on poly(di‐n‐pentylsilylene/n‐pentyloct‐7‐enyl) copolymers

Poly(dipentylsilylene) copolymers containing n‐pentyl‐n‐oct‐7‐enylsilane units were prepared by reductive coupling of the corresponding dichlorosilanes. Linear high molecular weight and some crosslinked polymer were obtained. The soluble products exhibited optical and thermal properties like poly(dipentylsilylene). Differential scanning calorimetry was used to investigate crystallization and to monitor thermal crosslinking. Vinyl functionalized side chains were hydrosilylated with dipentylsilane and dimethylchlorosilane and crosslinked via the side chains. Hydrosilylation with di‐n‐pentyl(trimethylsiloxypropyl)silane led to a partial hydroxy functionalization of the polysilylene and enabled anionic PEO grafting of the poly(dipentylsilylene). © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2306–2318, 2000     

Novel,organosoluble, light‐colored fluorinated polyimides based on 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)biphenyl or 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)‐1,1′‐binaphthyl

Two series of fluorinated polyimides were prepared from 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)biphenyl ( 2 ) and 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)‐1,1′‐binaphthyl ( 4 ) with various aromatic dianhydrides via a conventional, two‐step procedure that included a ring‐opening polyaddition to give poly(amic acid)s, followed by chemical or thermal cyclodehydration. The inherent viscosities of the polyimides ranged from 0.54 to 0.73 and 0.19 to 0.36 dL/g, respectively. All the fluorinated polyimides were soluble in many polar organic solvents, such as N,N‐dimethylacetamide and N‐methylpyrrolidone, and afforded transparent and light‐colored films via solution‐casting. These polyimides showed glass‐transition temperatures in the ranges of 222–280 and 257–351 °C by DSC, softening temperatures in the range of 264–301 °C by thermomechanical analysis, and a decomposition temperature for 10% weight loss above 520 °C both in nitrogen and air atmospheres. The polyimides had low moisture absorptions of 0.23–0.58%, low dielectric constants of 2.84–3.61 at 10 kHz, and an ultraviolet–visible absorption cutoff wavelength at 351–434 nm. Copolyimides derived from the same dianhydrides with an equimolar mixture of 4,4′‐oxydianiline and diamine 2 or 4 were also prepared and characterized. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2416–2431, 2004     

A series of novel side chain liquid crystalline polysiloxanes containing cyano‐ and cholesterol‐terminated substituents: Where will the structure‐dependence of terminal behavior of the side chain reappear?

A series of polysiloxane side chain liquid crystal polymers with strong polarity cyano substitution‐terminated achiral side chains and cholesterol‐terminated chiral side chains was successfully synthesized via thiol‐ene click chemistry. ¹H‐NMR, FT‐IR, and thermogravimetric analysis were used to confirm their chemical structures and thermal stabilities. Their phase transition behaviors and phase structures were systematically investigated by a combination of analysis methods such as differential scanning calorimetry, polarized optical microscopy, and X‐ray. Results revealed that attributing to the decisive role of the polarity interaction, all the polymers only developed a monolayer interdigitated SmA phase in which the period arrangement was determined by the cyano‐terminated side chains, the increased content of cholesterol‐terminated chiral side chains (X_chol) just expanded the distance between neighboring molecules within a layer. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1765–1772     

Controlled synthesis and microstructure tuning of PEG‐containing side‐chain discotic liquid crystalline block copolymers via RAFT polymerization

Liquid crystalline block copolymers (LCBCPs) are fascinating for their combining molecular level liquid crystalline orders and microphase separated multidomain morphologies. Here in this article, a series of PEG‐containing side‐chain discotic LCBCPs of PEG‐b‐P_m‐n with variant spacer length m = 6, 10 and degree of polymerization (DP) of discotic LC block from n = 10 to 45, have been well‐synthesized via reversible addition‐fragmentation chain‐transfer (RAFT) polymerization. The RAFT process mediated by macromolecular chain transfer agent (macroCTA) shows remarkable monomer concentration dependence. The influence of the introduced PEG block on the nano‐scale microphase‐segregation and mesophase organization is closely related to the side‐chain triphenylene (TP) discogens stacking mode dependent on the spacer length. Wherein, the PEG‐b‐P₆‐n series with a six‐methylene spacer exhibit consistent microphase separation with slightly disturbed yet ordered columnar structures. While for PEG‐b‐P₁₀‐n series with a longer ten‐methylene spacer, the columnar organization in the copolymers is even improved in contrast with the low order of randomly TP stacking in their corresponding homopolymers. This work offers a viable and inspiring pathway for controlled synthesis of block copolymers with bulky side groups, as well as enhances in‐depth understanding of the hierarchical superstructure organization in discotic units involved complex block copolymers. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2544–2553     

Highly organosoluble and flexible polyimides with color lightness and transparency based on 2,2‐bis[4‐(2‐trifluoromethyl‐4‐aminophenoxy)‐3,5‐dimethylphenyl]propane

A new diamine containing isopropylidene, methyl substituted arylene ether, and trifluoromethyl groups, 2,2‐bis[4‐(2‐trifluoromethyl‐4‐aminophenoxy)‐3,5‐dimethylphenyl]propane (BTADP), was synthesized and used in preparation of a series of polyimides by direct polycondensation with various aromatic tetracarboxylic dianhydrides in N, N‐dimethylacetamide (DMAc). All polymers derived from diamine (BTADP) with trifluoromethyl substituents were highly organosoluble in the solvents, like N‐methyl‐2‐pyrrolidinone (NMP), N,N‐dimethylacetamide, N,N‐dimethylformamide (DMF), pyridine, chloroform, tetrahydrofuran (THF), dimethyl sulfoxide (DMSO), dichloromethane, cyclohexanone, and γ‐butyrolactone at room temperature or upon heating at 70 °C. Inherent viscosities of the polyimides were found to range between 0.58 and 0.97 dL·g^?1. These polyimides had glass transition temperatures between 256 and 307 °C, and their 10% mass loss temperatures ranged from 440 to 462 °C and 421 to 443 °C under nitrogen and air, respectively. These polyimides had low dielectric constants in the range of 2.84–3.09. All the polyimides could be cast into films from DMAc solutions and were thermally converted into color lightness, optically transparent, flexible, and tough polyimides. The polyimide films had a tensile strength in the range of 83–97 MPa and a tensile modulus in the range of 2.0–2.2 GPa. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5766–5774, 2004     

Synthesis and characterization of novel polyimides bearing a side chain composed of stilbene mesogen and undecyl spacer and the alignment ability of nematic liquid-crystal molecules

Four different polyimides with side chains containing undecyl spacers and 4-fluorostilbene mesogen end groups were prepared, and their structures and the controllability of the liquid-crystal (LC) alignment with rubbing were investigated. From X-ray scattering and differential scanning calorimetry data, pyromellitic dianhydride (PMDA)-, benzophenone-3,3′,4,4′-tetracarboxylic dianhydride (BTDA)-, and 4,4′-oxydi(phthalic anhydride) (ODPA)-based polyimides were shown to have layered structures and short-range ordering. Pretilt angles of LCs on the rubbed surfaces were 1–9°, depending on the rubbing density and backbone. In particular, the long undecyl spacers caused the mesogenic stilbene end groups to lie next to the main chain, resulting in a reduction in the pretilt angles. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1800–1809, 2001     

Polymeric dopant effects of bent‐core covalent‐bonded and hydrogen‐bonded structures on banana‐shaped liquid crystalline complexes

Two series of banana‐shaped liquid crystalline (LC) H‐bonded complexes HP_m / CB_n (i.e., bent‐core H‐bonded side‐chain homopolymer HP mixed with bent‐core covalent‐bonded small molecule CB ) and CP_m / HB_n (i.e., bent‐core covalent‐bonded side‐chain homopolymer CP mixed with bent‐core H‐bonded small molecular complex HB ) with various m/n molar ratios were developed. The bent‐core covalent‐ and H‐bonded structural moieties were homopolymerized in the banana‐shaped LC H‐bonded complexes HP_m / CB_n and CP_m / HB_n , respectively. The influences of m/n molar ratios (polymeric moieties vs. small molecular moieties) on the mesomorphic and electro‐optical properties of both banana‐shaped LC H‐bonded complexes HP_m / CB_n and CP_m / HB_n were investigated. The polar smectic phases could be achieved and stabilized by smaller contents of polymeric dopants in banana‐shaped LC H‐bonded complexes, such as HP1/CB10 , HP1/CB15 , CP1/HB10 , and CP1/HB15 , which possessed tunable spontaneous polarization (Ps) values according to the molar ratios of m/n , that is, lower Ps values obtained in H‐bonded complexes HP_m /CB_n and CP_m / HB_n with higher ratios of H‐bonded moieties (larger m/n molar ratios), respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 764–774, 2010     

Synthesis and properties of polythiophenes with conjugated side‐chains containing carbon–carbon double and triple bonds

Two soluble side‐chain conjugated polythiophenes, poly{3‐[2‐(4‐octyloxy‐phenyl)‐vinyl]‐thiophene} (P3OPVT) and poly{3‐(4‐octyloxy‐phenylethynyl)‐thiophene} (P3OPET) have been synthesized successfully. In P3OPVT and P3OPET, substituted benzene rings are connected with the polythiophene backbone through trans carbon–carbon double bond and carbon–carbon triple bond, respectively. Absorption spectra of the P3OPVT and P3OPET both show two absorption peaks located in UV and visible region, respectively. The results of optical and electrochemical measurements indicate that the conjugated side‐chains can reduce the bandgap effectively. This type of side‐chain conjugated polythiophenes may be promising for the applications in polymer photovoltaic cells and field effect transistors. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2206–2214, 2006     

Synthesis,characterization and liquid crystal‐aligning properties of new poly{3‐[4‐(n‐alkyloxy)phenyloxy]pyromellitimide}s

Four new polypyromellitimides (MC_m‐PPIs and MC_m‐OPIs, m = 6, 8) that are singly substituted with a flexible n‐alkyloxy side branch at the pyromellitimide ring were prepared by the two‐step polycondensation of 3‐[4‐(n‐alkyloxy)phenyloxy]pyromellitic dianhydrides (MC_m‐PMDAs, m = 6, 8) with p‐phenylenediamine (PDA) and 4,4′‐oxydianiline (ODA), respectively. The dianhydride monomers were synthesized from durene via several reaction steps. Inherent viscosities of the precursor poly(amic acid)s ranged from 0.57 to 1.58 dl/g. After chemical structures of the polyimides had been characterized, their thermal properties, crystalline structures, and liquid crystal (LC) aligning abilities on their rubbed thin films were determined and discussed in comparison to the polypyromellitimides that are doubly substituted at the pyromellitimide ring with the same side branches. For all polymers thermogravimetric analysis (TGA) programs showed a typical two‐step degradation behavior with onset temperatures in the 430–455°C range. In X‐ray scattering studies all the samples were found to be amorphous, but the presence of a loosely developed layer structure could be confirmed, in which two main chains gather together to form a double‐strand backbone layer and n‐alkyl branches fill the space between the layers. On the rubbed surfaces of the polyimide thin films LCs uniformly aligned parallel to the rubbing direction with the pre‐tilt angles 5–7° in MC_m‐OPIs and 18–32° in MC_m‐PPIs. Copyright © 2006 John Wiley & Sons, Ltd.     

Formation and elasticity of layer networks

Layer network formation of poly(styrene‐alt‐n‐octadecylmaleimide) in dodecane is investigated. It is shown that the polymer in the bulk exhibits lamellar structures of alternated alkane side‐chain and main‐chain layers. Adding dodecane into the polymer separates the polymer layers, increases the mean distance between the layers, and results in a less orderly layered structure. Crystallization of the alkane side chains introduces linkages to staple the layers together and builds up a layer network. Dimensional analysis predicts that the modulus (G) of the layer network is simply related to the long period (L) of the layer network through a cubic power law, i.e., G ∼ L⁻³. This prediction is indeed observed experimentally. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 667–677, 1999     

Polyrotaxanes based on polyethers and β‐cyclodextrin

A polyrotaxane in which β‐cyclodextrins (β‐CDs) are threaded onto a polyether chain was prepared by polycondensation of a β‐CD/bisphenol A (BPA) inclusion complex with aromatic dihalides. Two dihalides, with and without a side chain, were used. This polycondensation results in a polyrotaxane (or pseudopolyrotaxane for polymers without stoppers) with a 1:1 threading ratio when the side chain is present and 2:3 when there is none. The long side chain prevents dethreading of the macrocycles. The best yield and a good threading ratio were obtained when the polycondensation was performed by liquid?solid phase transfer catalysis without solvent (L/S PTC) using 2,5‐bi(iodomethyl)‐4‐methoxy‐(1‐octyloxy)benzene as dihalide. The ¹H NMR and FTIR spectra show that the products consist of β‐CD and polyether. The 2D NOESY NMR spectrum shows that the polyether chains are included in the β‐CD cavity. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4391–4399, 2009