Oxidation polymerization of a charge‐transfer complex of 2,6‐bis(2‐thienyl)‐1,4‐dithiafulvene with 7,7,8,8‐tetracyanoquinodimethane

A π‐conjugated poly(α‐dithienylen‐dithiafulvene) ( 2 ) was obtained by the oxidation polymerization of 2,6‐bis(2‐thienyl)‐1,4‐dithiafulvene ( 1 ) as a dithiafulvene monomer derived from 4‐(2‐thienyl)‐1,2,3‐thiadiazole. When a solution of 1 in CHCl₃ was added to a stirred solution of FeCl₃ in CHCl₃, only the low‐molecular‐weight product 2 was obtained. The mixture was stirred for 15 h with an N₂ flow. The polymerization at higher temperatures resulted in polymers with large insoluble fractions. A higher molecular weight polymer was obtained by the oxidation polymerization of a charge‐transfer complex of 1 with 7,7,8,8‐tetracyanoquinodimethane (compound 3 ). In contrast to 2 , polymer 4 was readily soluble in dimethyl sulfoxide, dimethylformamide, and acetone and partially soluble in tetrahydrofuran and methanol and had a larger molecular weight (peak top molecular weight = 37,000). The conductivity of polymer 4 was 3 orders of magnitude larger than that of polymer 2 . © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6592–6598, 2005     

Synthesis and properties of π‐conjugated dithiafulvene oligomers by addition of a monofunctionalized compound

Dithiafulvene oligomers ( 3 ) were prepared by cycloaddition polymerization of aldothioketenes with their alkynethiol tautomers derived from 1,4‐diethynylbenzene ( 2 ) with the addition of 1‐ethynyl‐4‐methylbenzene ( 1 ) as a monofunctionalized compound. Different feed ratios of 2 / 1 were used to control the molecular weights of 3 . The structures of 3 were confirmed by IR and ¹H NMR spectroscopies in comparison with those of 2‐(4‐tolylidene)‐4‐tolyl‐1,3‐dithiol ( 4 ) as a model compound, which was obtained by the treatment of lithium 2‐tolylethynethiolate with water in Et₂O. The number‐average degree of polymerization (DP) and the number‐average molecular weight were measured by gel permeation chromatographic and ¹H NMR analysis. DP increased with an increasing feed ratio of 2 / 1 . The ultraviolet–visible spectra of 3 in diluted acetonitrile showed that the absorption maxima of 3 increased with an increasing DP of 3 . These redshifts are ascribed to an effective expansion of the π‐conjugation system in 3 . The oligomers exhibited a maximum conjugation length of seven repeating units. The redox properties of 3 were examined by cyclic voltammetry. The oxidation half‐peak potentials (E_p/2) of 3 were slightly cathodically shifted with increasing DP. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 708–715, 2003     

Synthesis and characterization of novel π‐conjugated polymers with phosphole ring derivatives

Novel π‐conjugated polymers ( 8 – 10 ) were prepared by the palladium‐catalyzed Sonogashira coupling reaction of three kinds of phosphole‐ring‐containing monomers with 2,5‐dihexyloxyl‐1,4‐diethynylbenzene. The obtained polymers ( 8 – 10 ) were regioregulated with the 2,5‐substituted phosphole ring in the polymer main chain and characterized with ¹H, ¹³C, and ³¹P NMR and FTIR. Polymers 8 – 10 were found to have an extended π‐conjugated system according to the results of UV–vis absorption spectra. In the fluorescence emission spectra of 8 – 10 , moderate emission peaks were observed in the visible blue‐to‐green region. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2867–2875, 2007     

Alternating π‐conjugated copolymer of dithiafulvene with 2,2′‐bipyridyl units

A π‐conjugated polymer containing a dithiafulvene unit and a bipyridyl unit was prepared by cycloaddition polymerization of aldothioketene derived from 5,5′‐diethynyl‐2,2′‐bipyridine. Ultraviolet–visible (UV–vis) absorption spectra showed that the π‐conjugation system of the polymer expanded more effectively than that of a benzene analogue of poly(dithiafulvene) obtained from 1,4‐diethynylbenzene. Cyclic voltammetry measurements indicated that the dithiafulvene–bipyridyl polymer was a weaker electron‐donor polymer than the benzene analogue. These results supported the idea that the incorporation of the electron‐accepting bipyridyl moiety into conjugated poly(dithiafulvene) induced an intramolecular charge‐transfer (CT) effect between the units. Treatment of the dithiafulvene–bipyridyl polymer with bis(2,2′‐bipyridyl)dichlororuthenium (II) [Ru(bpy)₂Cl₂] afforded a ruthenium–polymer complex. A cyclic voltammogram of the complex showed broad redox peaks, which indicated electronic interaction between the dithiafulvene and tris(bipyridyl) ruthenium complex. The dithiafulvene–bipyridyl polymer formed CT complexes with 7,7,8,8‐tetracycanoquinodimethane (TCNQ) in dimethyl sulfoxide. The UV–vis absorption indicated that the resulting CT complex contained anion radical of TCNQ and partially charge‐transferred TCNQ. The polymer showed an unusually high electrical conductivity of 3.1 × 10^?4 S/cm in its nondoped state due to the effective donor–acceptor interaction between the bipyridine unit and the dithiafulvene unit. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4083–4090, 2001     

Synthesis and spectroscopic investigation of π‐conjugated (E)‐enyne polycarbazole with different organo‐metallic catalysts from 3,6‐diethynyl‐9‐(2‐ethylhexyl)carbazole

In the present study, a new (E)‐rich‐enyne π‐conjugated polymer containing a carbazole was designed and synthesized. Two different synthesis methods of poly[N‐(2‐ethylhexyl)‐3,6‐carbazolyleneethynylene‐(E)‐vinylene] (PCZEV) have been prepared from 3,6‐diethynyl‐9(2‐ethylhexyl)carbazole by using the palladium‐carbene‐catalyzed reaction and/or by using the organolanthanide‐catalyzed reaction leading to well‐defined polymer, and their general properties were studied. Compared to poly[N‐(2‐ethylhexyl)‐3,6‐carbazolyleneethynylene] (PCE), the UV‐vis absorption and photoluminescence of the PCZEV was red‐shifted, which indicates the extension of conjugation length. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2434–2442, 2009     

High‐performance amorphous donor–acceptor conjugated polymers containing x‐shaped anthracene‐based monomer and 2,5‐bis(2‐octyldodecyl)pyrrolo[3,4‐c]pyrrole‐1,4(2H,5H)‐dione for organic thin‐film transistors

New diketopyrrolopyrrole (DPP)‐containing amorphous conjugated polymers, such as poly(3‐(5‐((9,10‐bis((4‐hexylphenyl)ethynyl)‐6‐(prop‐1‐ynyl)anthracen‐2‐yl)ethynyl) thiophen‐2‐yl)‐5‐(2‐hexyldecyl)‐2‐(2‐octyldodecyl)‐6‐(thiophen‐2‐yl)pyrrolo[3,4‐c]pyrrole‐1,4(2H,5H)‐dione) ( 4 ), and poly(3‐(5‐((2,6‐bis((4‐hexylphenyl)ethynyl)‐10‐(prop‐1‐ynyl)anthracen‐9‐yl)ethynyl)thiophen‐2‐yl)‐2,5‐bis(2‐octyldodecyl)‐6‐(thio phen‐2‐yl)pyrrolo[3,4‐c]pyrrole‐1,4(2H,5H)‐dione) ( 7 ), were successfully synthesized via Sonogashira coupling reactions under microwave conditions. Copolymer 7 , incorporating a DPP moiety at the 9,10‐position of the anthracene ring through a triple bond, showed a much lower bandgap energy (E_g = 1.81 eV) than copolymer 4 (E_g = 2.13 eV). Tuning of the molecular frontier orbital energies was achieved by only changing the anchoring position of dithiophenyl‐DPP from the 2,6‐ to the 9,10‐position in the anthracene ring. Because of the donor–acceptor (D–A) interaction and the two‐dimensional planar structure of the X‐shaped donor monomer, the resulting polymers showed good interchain π?π stacking in the thin‐film state, despite being amorphous polymers. When the newly synthesized polymer 7 was used as a semiconductor material in an organic thin‐film transistor, the best mobility of up to 0.12 cm² V^?1 s^?1 (I_on/off = ～ 4.4 × 10⁶) was observed, which is one of the highest values recorded for amorphous polymer films reported to date. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and characterization of new π‐conjugated polymers containing 1,8‐naphthyridine in the main chain: Role of the 1,8‐naphthyridine unit in π‐conjugated polymers

Alternating π‐conjugated copolymers of 1,8‐naphthyridine‐2,6‐diyl ( 1,8‐Nap ) with 9,9‐dioctylfluorene‐2,7‐diyl ( P(Flu‐Ph‐1,8‐Nap) ) and 2,5‐didodecyloxy‐1,4‐phenylene ( P(ROPh‐Ph‐1,8‐Nap) ) have been synthesized by Pd‐catalyzed organometallic polycondensation. The copolymers showed UV‐vis absorption peaks at around 390 nm in o‐dichlorobenzene. The polymers were photoluminescent both in o‐dichlorobenzene and in the solid state. In o‐dichlorobenzene, the emission peaks of P(Flu‐Ph‐1,8‐Nap) and P(ROPh‐Ph‐1.,8‐Nap) appeared at λ_EM = 440 and 471 nm, with quantum yields of 87% and 66%, respectively. Electrochemical data revealed that 1,8‐Nap behaved as a typical electron‐accepting unit. When P(Flu‐Ph‐1,8‐Nap) was treated with 10‐camphorsulfonic acid, the emission peak shifted to λ_EM = 598 nm. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and photovoltaic properties of 2,6‐bis(2‐thienyl) benzobisazole and 4,8‐bis(thienyl)‐benzo[1,2‐B:4,5‐B′]dithiophene copolymers

In an effort to design efficient low‐cost polymers for use in organic photovoltaic cells the easily prepared donor–acceptor–donor triad of a either cis‐benzobisoxazole, trans‐benzobisoxazole or trans‐benzobisthiazole flanked by two thiophene rings was combined with the electron‐rich 4,8‐bis(5‐(2‐ethylhexyl)‐thien‐2‐yl)‐benzo[1,2‐b:4,5‐b′]dithiophene. The electrochemical, optical, morphological, charge transport, and photovoltaic properties of the resulting terpolymers were investigated. Although the polymers differed in the arrangement and/or nature of the chalcogens, they all had similar highest occupied molecular orbital energy levels (?5.2 to ?5.3 eV) and optical band gaps (2.1–2.2 eV). However, the lowest unoccupied molecular orbital energy levels ranged from ?3.1 to ?3.5 eV. When the polymers were used as electron donors in bulk heterojunction photovoltaic devices with PC₇₁BM ([6,6]‐phenyl C₇₁‐butyric acid methyl ester) as the acceptor, the trans‐benzobisoxazole polymer had the best performance with a power conversion efficiency of 2.8%. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 316–324     

Synthesis and characterization of donor–acceptor poly(3‐hexylthiophene) copolymers presenting 1,3,4‐oxadiazole units and their application to photovoltaic cells

We have used Grignard metathesis polymerization to prepare poly(3‐hexylthiophene)‐based copolymers containing electron‐withdrawing 4‐tert‐butylphenyl‐1,3,4‐oxadiazole‐phenyl moieties as side chains. We characterized these copolymers using ¹H and ¹³C nuclear magnetic resonance spectroscopy, thermogravimetric analysis, and gel permeation chromatography. The band gap energy of copolymer was determined from the onset of the optical absorption. The quenching effects were observed in the photoluminescence spectra of the copolymers incorporating pendant electron‐deficient 1,3,4‐oxadiazole moieties on the side chains. The photocurrents of devices were enhanced in the presence of an optimal amount of the 1,3,4‐oxadiazole moieties, thereby leading to improved power conversion efficiencies. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3331–3339, 2010     

Synthesis and photovoltaic behaviors of narrow‐band‐gap π‐conjugated polymers composed of dialkoxybenzodithiophene‐ and thiophene‐based fused aromatic rings

π‐Conjugated polymers, PBDT‐CNETT and PBDT‐CNECPDT , were prepared by the Stille cross‐coupling polymerization. Optical and thermal properties of the obtained polymers were investigated by UV–vis spectroscopy and thermogravimetric analysis. PBDT‐CNETT and PBDT‐CNECPDT exhibited very narrow band gaps of 1.39 and 1.13 eV, respectively. Highest occupied molecular orbital energy levels estimated by surface analyzer were ?5.17 and ?5.11 eV for PBDT‐CNETT and PBDT‐CNECPDT , respectively. The solar cells based on these polymers were evaluated with the cell configuration of ITO/PEDOT‐PSS/polymer:PC₆₁BH/LiF/Al. The power conversion efficiencies of the solar cells were estimated to be 1.57 and 0.16% for PBDT‐CNETT and PBDT‐CNECPDT , respectively. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Poly((2‐alkylbenzo[1,2,3]triazole‐4,7‐diyl)vinylene)s for organic solar cells

Poly((2‐Alkylbenzo[1,2,3]triazole‐4,7‐diyl)vinylene)s (pBTzVs) synthesized by Stille coupling show different absorption spectra, solid‐state morphology, and photovoltaic performance, depending on straight‐chain versus branched‐chain (pBTzV12 and pBTzV20) pendant substitution. Periodic boundary condition density functional computations show limited alkyl pendant effects on isolated chain electronic properties; however, pendants could influence polymer backbone conjugative planarity and polymer solid film packing. The polymers are electronically ambipolar, with best performance by pBTzV12 with hole and electron transport mobilities of 4.86 × 10^?6 and 1.96 × 10^?6 cm² V^?1 s^?1, respectively. pBTzV12 gives a smooth film morphology, whereas pBTzV20 gives a very different fibrillar morphology. For ITO/PEDOT:PSS/(1:1 w/w polymer:PC₇₁BM)/LiF/Al devices, pBTzV12 gives power conversion efficiency (PCE) up to 2.87%, and pBTzV20 gives up to PCE = 1.40%; both have open‐circuit voltages of V_OC = 0.6–0.7 V. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1539–1545     

Synthesis and properties of blue light‐emitting,silicon‐containing,regio‐ and stereoregular conjugated polymers

This article concerns the hydrosilylation polyaddition of 1,4‐bis(dimethylsilyl)benzene ( 1 ) with 4,4′‐diethynylbiphenyl, 2,7‐diethynylfluorene ( 2b ), and 2,6‐diethynylnaphthalene with RhI(PPh₃)₃ catalyst. Trans‐rich polymers with weight‐average molecular weights (M_w's) ranging from 19,000 to 25,000 were obtained by polyaddition in o‐Cl₂C₆H₄ at 150–180 °C, whereas cis‐rich polymers with M_w's from 4300 to 34,000 were obtained in toluene at 0 °C–r.t. These polymers emitted blue light in 4–81% quantum yields. The cis polymers isomerized into trans polymers upon UV irradiation, whereas the trans polymers did not. The device having a layer of polymer trans‐ 3b obtained from 1 and 2b demonstrated electroluminescence without any dopant. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2774–2783, 2004     

Alternating copolymers of 2,6‐bis(p‐dihexylaminostyryl)anthracene‐9,10‐diyl and N‐octylcarbazole with large two‐photon cross sections

We report the synthesis, thermal, one‐ and two‐photon properties of poly(2,6‐bis(p‐dihexylaminostyryl)anthracene‐9,10‐diyl‐alt‐N‐octylcarbazole‐3,6‐/2,7‐diyl) ( P1/P2 ). The as‐synthesized polymers exhibit number‐average molecular weights of 1.7 × 10⁴ for P1 and 2.1 × 10⁴ g/mol for P2 . They emit strong one‐ and two‐photon excitation fluorescence with the peak around 502 nm, and the fluorescence quantum yields around 0.76 in chloroform. In film state, P1 and P2 show different red‐shift emission with the peaks at 512 nm and 523 nm, respectively. The DSC measurement reveals that as‐synthesized polymers are all amorphous aggregates with the glass transition temperatures of 131 °C for P1 and 152 °C for P2 . The solution two‐photon absorption (TPA) properties of P1 and P2 in chloroform are measured by the two‐photon‐induced fluorescence method using femtosecond laser pulses (120 fs). The TPA cross sections (δ) are measured over the range of 700–900 nm. The maximal δ of P1 and P2 all appear at ～800 nm and are 1010 GM and 940 GM per repeating unit, respectively. This suggests that no notable interactions among structure units that impair their fluorescence and TPA properties, and the polymers with large δ can be obtained by using the high TPA‐active units as building blocks. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Heteroarene‐fused π‐conjugated main‐chain polymers containing 4,7‐bis(4‐octylthiophen‐2‐yl)benzo[c][1,2,5]thiadiazole or 2,5‐bis(4‐octylthiophen‐2‐yl)thiazolo[5,4‐d]thiazole and their application to photovoltaic devices

Two conjugated main‐chain polymers consisting of heteroarene‐fused π‐conjuagted donor moiety alternating with 4,7‐bis(5‐bromo‐4‐octylthiophen‐2‐yl)benzo[c][1,2,5]thiadiazole (P1) or 2,5‐bis(5‐bromo‐4‐octylthiophen‐2‐yl) thiazolo[5,4‐d]thiazole (P2) units have been synthesized. They are intrinsically amorphous in nature and do not exhibit crystalline melting temperatures during thermal analysis. The effect of the fused rings on the thermal, optical, electrochemical, charge transport, and photovoltaic properties of these polymers has been investigated. The polymer (P1) containing 4,7‐bis(5‐bromo‐4‐octylthiophen‐2‐yl)benzo[c][1,2,5] thiadiazole has a broad absorption extending from 300 to 600 nm with optical bandgaps as low as 2.02 eV. The HOMO levels (5.42 to 5.29 eV) are more sensitive to the choice of acceptor. The polymers were employed to fabricate organic photovoltaic cells with methanofullerene [6,6]‐phenyl C71‐butyric acid methyl ester (PC₇₁BM). As a result, the polymer solar cell device containing P1 had the best preliminary results with an open‐circuit voltage of 0.61 V, a short‐circuit current density of 6.19 mA/cm², and a fill factor of 0.32, offering an overall power conversion efficiency of 1.21%. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and characterization of a π‐conjugated hybrid of oligothiophene and porphyrin

5‐(3‐Thienyl)‐10,15,20‐triethyl‐21H,23H‐porphine (H₂(ttep)) was synthesized and characterized. Oxidative polymerization of H₂(ttep) gave a novel oligomeric porphyrin linked at the 2,5‐positions of the thienyl group. Electric conductivity of 4 × 10^?1 S/cm after I₂ doping indicated that the oligomer had a π‐conjugated structure with a delocalization of π electrons over the thienylene backbone. PM3 calculations revealed a low HOCO‐LUCO gap, which was consistent with the relatively high electric conductivity. Regioregular (head‐to‐tail) structure was inferred from spectroscopic and calculational results. The pendant porphyrin groups formed a regular J‐type array along the thienylene backbone, which was indicated by a significant red shift of the Soret band maximum. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5403–5412, 2006     

Effect of conjugated core building block dibenzo[a,c]phenazine unit on π‐conjugated electrochromic polymers: Red‐shifted absorption

A comparative investigation was undertaken for the electrosynthesis and electrochemical properties of three different electroactive polymers having a conjugated core building block, dibenzo[a,c]phenazine. A series of monomers has been synthesized as regards to thiophene based units; thiophene, 3‐hexyl thiophene, and 3,4‐ethylenedioxythiophene. The effects of different donor substituents on the polymers' electrochemical properties were examined by cyclic voltammetry. Introducing highly electron‐donating (ethylene dioxy) group to the monomer enables solubility while also lowering the oxidation potential. The planarity of the monomer unit enhances π‐stacking and consequently lowering the E_g from 2.4 eV (PHTP) to 1.7 (PTBP). Cyclic voltammetry and spectroelectrochemical measurements revealed that 2,7‐bis(4‐hexylthiophen‐2‐yl)dibenzo[a,c]phenazine (HTP) and 2,7‐bis(2,3‐dihydrothieno[3,4‐b][1,4]dioxin‐5‐yl)dibenzo[a,c]phenazine (TBP) possessed electrochromic behavior. The colorimetry analysis revealed that while PTBP have a color change from red to blue, PHTP has yellow color at neutral state and blue color at oxidized state. Hence the presence of the phenazine derivative as the acceptor unit causes a red shift in the polymers' absorption to have a blue color. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1714–1720, 2010     

Regioselective grignard metathesis reaction of 2,5‐dibromo‐3‐(6′‐hexylpyridine‐2′‐yl)thiophene and kumada coupling polymerization

2,5‐Dibromo‐3‐(6′‐hexylpyridine‐2′‐yl)thiophene ( DBPyTh ) was synthesized by the Suzuki coupling reaction between two aromatic compounds followed by the bromination. The Grignard metathesis reaction of DBPyTh with isopropylmagnesium chloride proceeded in 85% conversion and the regioselective halogen–metal exchange at the 2‐position was confirmed. Namely, 5‐bromo‐2‐chloromagnesio‐3‐(6′‐hexylpyridine‐2′‐yl)thiophene and 2‐bromo‐5‐chloromagnesio‐3‐(6′‐hexylpyridine‐2′‐yl)thiophene were generated in 90:10 molar ratio. Subsequently, the Kumada coupling polymerization was carried out using 1,3‐bis(diphenylphosphinopropane)nickel(II) dichloride to obtain poly(3‐(6′‐hexylpyridine‐2′‐yl)thiophene) ( PolyPyTh ). The polymer molecular weight could be roughly controlled by the catalyst concentration and the molecular weight distribution ranged from 1.25 to 1.80. The gas chromatograph analysis indicated that 5‐bromo‐2‐chloromagnesio‐3‐(6′‐hexylpyridine‐2′‐yl)thiophene was preferentially polymerized in 90% conversion and the percentage of the head‐to‐tail content (regioregularity) was calculated to be 96%. The matrix‐assisted laser desorption/ionization time‐of‐fright mass spectrum indicated that both polymer chain ends were substituted with the hydrogen atom. The absorption maxima of polymer in CHCl₃ and thin film were observed at 447 and 457 nm, respectively, which were blue‐shifted compared with poly(3‐(4′‐octylphenyl)thiophene). From the CV measurement of the polymer thin film, highest occupied molecular orbital (HOMO) (?5.31 eV) and lowest unoccupied molecular orbital (LUMO) (?3.76 eV) energy levels were calculated from the oxidation and reduction onset potentials, respectively, and the electrochemical band gap energy was determined to be 1.62 eV. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of fluoro‐substituted silole‐containing conjugated materials

2,5‐Dihydroxyboryl‐1,1‐dimethyl‐3,4‐bis(3‐fluorophenyl)‐silole ( 2a ) was prepared in 40% overall yield by reaction between 3‐fluorophenyl‐acetylene and dichlorodimethylsilane to yield bis[2(3‐fluorophenyl)ethynyl]dimethylsilane ( 1a ), which subsequently undergoes a reductive cyclization reaction using an excess of lithium naphthalenide. The fluoro substituted silole was applied as a co‐monomer in the Suzuki polycondensation reaction with 2,7‐dibromo‐9,9‐dioctyl‐fluorene. An oligomer ( 3a ) with a degree of polymerization of 6 was prepared and compared with an oligomer without fluoro substitution on the silole ( 3b ), with a degree of polymerization of 4. The new oligomers were spin coated onto glass slides and showed weak green photoluminescence (PL) in the solid state. Cyclic voltammetry, visible absorption spectroscopy, and density functional theory calculations showed that the fluoro substituents were sufficiently electron withdrawing to lower both the highest occupied molecular orbital and the lowest unoccupied molecular orbital in the oligomer. Two further alternating co‐oligomers were prepared from 2,5‐dihydroxyboryl‐1,1‐dimethyl‐3,4‐bis(phenyl)‐silole ( 2b ) and 1,3‐dibromo‐5‐fluoro‐benzene ( 4a ) or 1,3‐dibromobenzene ( 4b ). These oligomers both had degrees of polymerization of 8 and showed green PL in the solid state. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5116–5125, 2009