Crystallization and morphology of poly(ethylene‐2,6‐naphthalene dicarboxylate) in the presence of nucleating agents

The crystallization and morphology of poly(ethylene‐2,6‐naphthalene dicarboxylate) (PEN) containing, as nucleating agents, a sodium salt of a copolymer of ethylene and acrylic acid or a sodium salt of a copolymer of ethylene and methacrylic acid, were investigated with differential scanning calorimetry, polarized optical microscopy, and small‐angle light scattering. The nucleating agents accelerated the crystallization rate at high temperatures by decreasing the surface free energy barrier hindering nucleation. Meanwhile, the nucleating agents with flexible chains could also improve the mobility of the PEN chains and increase the crystallization rate at low temperatures. Hedrites were observed when PEN was crystallized at high temperatures, whereas crystallization at low temperatures led to the formation of spherulites. Similar but smaller morphologies were obtained in the presence of nucleating agents. With nucleating agents, the spherulites formed at low temperatures were less perfect, although the optical properties of the spherulites were not influenced. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2387–2394, 2002     

X‐ray studies on the double melting behavior of poly(butylene terephthalate)

The double melting behavior of poly(butylene terephthalate) (PBT) was studied with differential scanning calorimetry (DSC) and wide‐angle X‐ray analysis. DSC melting curves of melt‐crystallized PBT samples, which we prepared by cooling from the melt (250 °C) at various cooling rates, showed two endothermic peaks and an exothermic peak located between these melting peaks. The cooling rate effect on these peaks was investigated. The melt‐crystallized PBT sample cooled at 24 K min^?1 was heated at a rate of 1 K min^?1, and its diffraction patterns were obtained successively at a rate of one pattern per minute with an X‐ray measurement system equipped with a position‐sensitive proportional counter. The diffraction pattern did not change in the melting process, except for the change in its peak height. This suggests that the double melting behavior does not originate from a change in the crystal structure. The temperature dependence of the diffraction intensity was obtained from the diffraction patterns. With increasing temperature, the intensity decreased gradually in the low‐temperature region and then increased distinctly before a steep decrease due to the final melting. In other words, the temperature‐dependence curve of the diffraction intensity showed a peak that is interpreted as proof of the recrystallization in the melting process. The peak temperature was 216 °C. The temperature‐dependence curve of the enthalpy change obtained by the integration of the DSC curve almost coincided with that of the diffraction intensity. The double melting behavior in the heating process of PBT is concluded to originate from the increase of crystallinity, that is, recrystallization. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2005–2015, 2001     

Analysis of crystallization behavior and crystal modifications of poly(butylene‐2,6‐naphthalene dicarboxylate)

Information on the crystalline structure and the properties of poly(butylene‐2,6‐naphthalene dicarboxylate) (PBN) has not been well reported until now, but it is known that there are two different crystal modifications in PBN, as follows: one is formed in isotropic samples by annealing (α form); another appears by annealing with tension (β form). The relation between the crystal modifications and the kinetics of isothermal crystallization for PBN was investigated using in‐situ Fourier transform infrared spectroscopy (FTIR) and wide‐angle X‐ray diffraction (WAXD). The melting behavior of each crystalline form was also studied by means of FTIR and differential scanning calorimetry (DSC) measurements. From the analysis of the melt‐crystallized PBN specimens, the two crystalline forms coexisted in the isotropic samples melt‐crystallized at 230°C, but only the α crystal modification was observed in the films annealed at lower temperatures. In addition, it was revealed that, at 230°C, the β modification was formed only in the primary crystallization process. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 561–574, 1999     

Crystal modifications and multiple melting behavior of poly(L‐lactic acid‐co‐D‐lactic acid)

The crystal modifications and multiple melting behavior of poly(L ‐lactic acid‐co‐D ‐lactic acid) (98/2) as a function of crystallization temperature were studied by wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). It was found that the disorder (α′) and order (α) phases of poly(L ‐lactic acid) (PLLA) were formed in cold‐crystallized poly(L ‐lactic acid‐co‐D ‐lactic acid) samples at low (<110 °C) and high (≥110 °C) temperatures, respectively. A disorder‐to‐order (α′‐to‐α) phase transition occurred during the annealing process of the α′‐crystal at elevated temperatures, which proceeded quite slowly even at the peak temperature of the exotherm P_exo but much more rapidly at higher temperature close to the melting region. The presence or absence of an additional endothermic peak before the exotherm in the DSC thermograph of the α′‐crystal was strongly dependent on the heating rate, indicating that a melting process involved during the α′‐to‐α phase transition. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Analysis of the complex thermal behavior of poly(L‐lactic acid) film. II. Samples crystallized from the melt

The complex thermal behavior of poly(l ‐lactic acid) films crystallized from the melt, either isothermally or nonisothermally, was studied by differential scanning calorimetry (DSC), wide angle X‐ray diffraction, and small angle X‐ray scattering. The variation of the thermal behavior with crystallization temperature, time, and cooling rate was documented and analyzed. After nonisothermal crystallization at low cooling rates that develop high crystallinity, an obvious double melting peak appears at modest heating rates (e.g., 10 °C/min). At higher heating rates, these samples exhibit only single melting. However, an unusual form of double melting occurs under the majority of the conditions studied under either isothermal or nonisothermal conditions. In this case, double melting is marked by the appearance of a recrystallization exotherm just prior to the final melting that obscures the observation of the melting of the crystals formed during the initial crystallization process. The occurrence of double melting in melt‐crystallized samples was concluded to be the result of a melt‐recrystallization process occurring during the subsequent DSC heating scan; it is a function of crystalline perfection, not the initial crystallinity, nor whether or not the crystallization reached completion at the crystallization temperature. Many other very interesting observations are also discussed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3378–3391, 2006     

成核剂对聚2,6-萘二甲酸乙二酯结晶行为的影响

通过DSC、偏光显微镜 (POM)和小角激光散射 (SALS)研究了苯甲酸钠 (SB)对聚 2 ,6 萘二甲酸乙二酯(PEN)结晶行为的影响 .研究发现SB是PEN的成核剂 .在高温下 ,SB与PEN发生化学反应 ,生成可以起到成核作用的物质 ,降低了PEN的成核表面自由能位垒 ,提高了PEN在高温区的结晶速率 .同时 ,SB还可以提高PEN在低温区的结晶速率 .此外 ,SB的加入还使PEN分别在高温区和低温区结晶得到的多角晶和球晶尺寸减小 ,这表明不管在高温区还是在低温区 ,SB都可以提高PEN的成核速率 .而含有SB的PEN结晶样品的SALS图像变得弥散、模糊 ,则说明SB使PEN在低温下结晶得到的球晶变得不完善     

Effect of silver nanoparticles on the dynamic crystallization behavior of nylon‐6

The effect of introducing silver nanoparticles on the rheological properties and dynamic crystallization behavior of nylon‐6 was investigated. The nanocomposites showed slightly higher viscosity than pure nylon‐6 in the low‐frequency range even at an extremely low loading level of the silver particles (0.5–1.0 wt %). The nanoparticles had a more noticeable effect on the storage modulus than on the loss modulus of a nylon‐6 melt and reduced its loss tangent. They increased the crystallization temperature of nylon‐6 by about 14 °C and produced a sharper crystalline peak. The silver nanoparticles promoted the crystallization of nylon‐6, and their effect on the dynamic crystallization of nylon‐6 at 200 °C was more notable at a lower shear rate and at 190 °C at a higher frequency. Nylon‐6 produced large spherulitic crystals, but the nanocomposites showed a grainy structure. In addition, the silver nanoparticles reduced the fraction of the α‐form crystal but increased that of the γ‐form crystal. The nanocomposites crystallized at 190 °C showed a lower melting temperature than nylon‐6 by about 3 °C, whereas the nanocomposites crystallized at 200 °C showed almost the same melting temperature. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 790–799, 2004     

Crystallization behavior of P(EN‐co‐ET) copolyesters: Crystallization kinetics and morphology revealed by DSC,time‐resolved SAXS analysis,and TEM

The crystallization kinetics and morphology of PEN/PET copolyesters were investigated using differential scanning calorimetry (DSC), time‐resolved small‐angle X‐ray scattering (TR‐SAXS), and transmission electron microscopy (TEM). The Avrami exponents obtained using DSC were approximately 3 for homo PEN and 4 for all the copolyesters. The 3‐parameter Avrami model was successfully fitted to the invariants with respect to the time obtained from TR‐SAXS, and the exponent values were similar to those obtained from DSC. Moreover, the Avrami rate constants obtained from TR‐SAXS showed marked temperature‐sensitive decreases in all samples, like those obtained from DSC. This indicates that not only could changes in morphological parameters be obtained from the analysis of TR‐SAXS data but also crystallization kinetics. The changes in the morphological parameters determined from the SAXS data indicate that the minor components, dimethyl terephthalate (DMT) segments, are rejected into the amorphous phase during crystallization. In the TEM study, copolyesters crystallized at temperature above 240 °C grew into both the α‐ and β‐form, although 240 °C is the optimum condition for the β‐form crystal. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 805–816, 2005     

Thermal memory of poly(3‐hydroxybutyrate) using temperature‐modulated differential scanning calorimetry

The influence of thermal history on morphology, melting, and crystallization behavior of bacterial poly(3‐hydroxybutyrate) (PHB) has been investigated using temperature‐modulated DSC (TMDSC), wide‐angle X‐ray diffraction (WAXRD) and polarized optical microscopy (POM). Various thermal histories were imparted by crystallization with continuous and different modulated cooling programs that involved isoscan and cool–heat segments. The subsequent melting behavior revealed that PHB experienced secondary crystallization during heating and the extent of secondary crystallization varied with the cooling treatment. PHB crystallized under slow, continuous, and moderate cooling rates were found to exhibit double melting behavior due to melting of TMDSC scan‐induced secondary crystals. PHB underwent considerable secondary crystallization/annealing that took place under modulated cooling conditions. The overall melting behavior was interpreted in terms of recrystallization and/or annealing of crystals. Interestingly, the PHB analyzed by temperature modulation programs showed a broad exotherm before the melting peak in the nonreversing heat capacity curve and a multiple melting reversing curve, verifying that the melting–recrystallization and remelting process was operative. WAXRD and POM studies supported the correlations from DSC and TMDSC results. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 70–78, 2006     

Thermal analysis of the multiple melting behavior of poly(butylene succinate‐co‐adipate)

The melting behavior of poly(butylene succinate‐co‐adipate) (PBSA) isothermally crystallized from the melt was investigated by differential scanning calorimetry. Triple, double, or single melting endotherms were observed in subsequent heating scan for the samples isothermally crystallized at different temperatures. These endothermic peaks were labeled as I, II, and III for low‐, middle‐, and high‐temperature melting endotherms, respectively. The independence of endotherm III to the crystallization temperature, the existence of an exothermic crystallization peak just below the endotherm III, and the heating rate dependence of endotherm III indicated that endotherm III was due to the remelting of recrystallized lamellar during a heating scan. The influence of crystallization time on the melting behavior of PBSA showed that endotherms II and III developed prior to endotherm I; endotherm III developed rather simultaneously with endotherm II. Further investigation showed that the peak temperature of endotherm I increased linearly with the logarithm of the crystallization time. It suggested that endotherm II was attributed to the melting of the primary lamellae, while endotherm I was due to the melting of secondary lamellae. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3077–3082, 2005     

Differential scanning calorimetry study on thermal behaviors of freeze‐dried poly(L‐lactide) from dilute solutions

Glass transition, cold crystallization, and melting of freeze‐dried poly(L‐lactide) (PLLA) prepared from dilute 1,4‐dioxane solutions were investigated by differential scanning calorimetry (DSC). Conventional DSC measurements of heating scans revealed that freeze‐dried PLLA prepared from a 0.07 wt % solution undergoes a two‐step cold crystallization (or reorganization) with a lower exotherm appearing at about 78 °C and with a higher broad exotherm between 110–155 °C. The peak temperature of the former exotherm is about 50 K lower than that observed for a reference bulk sample. Step‐scan mode DSC, which provides information essentially equivalent to that obtained from the temperature‐modulated DSC, revealed that the glass‐transition temperature is about 6 K lower than that of the reference bulk. These findings suggest enhanced chain mobility for freeze‐dried PLLA. Freeze‐dried PLLA that crystallized at 80 °C for 40 min was revealed to contain a rather large amount of rigid amorphous material (42%). © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 115–124, 2005     

Study of the crystallization behaviors of isotactic polypropylene with sodium benzoate as a specific versatile nucleating agent

Sodium benzoate (SB), a conventional nucleating agent of α‐phase isotactic polypropylene (iPP) was discovered to induce the creation of β‐phase iPP under certain crystalline conditions. Polarized optical microscopy (POM) and wide angle X‐ray diffraction (WAXD) were carried out to verify the versatile nucleating activity of SB and investigate the influences of SB's content, isothermal crystallization temperature, and crystallization time on the formation of β‐phase iPP. The current experimental results indicated that, under isothermal crystallization conditions, SB showed peculiar nucleating characteristics on inducing iPP crystallization which were different from those of the commercial β form nucleating agent (TMB‐5). The content of β crystal form of iPP nucleated with SB (PP/SB) increased initially with the increase of crystallization temperature, nucleating agent (SB) percentage or crystallization time, reached a maximum value, and then decreased as the crystallization temperature, nucleating agent percentage or crystallization time further increased. While the content of β crystal form of iPP nucleated with TMB‐5 (PP/TMB‐5) showed a completely different changing pattern with the crystallization conditions. The obvious difference of the two kinds of nucleating agents on inducing iPP crystallization can be explained by the versatile nucleating ability of SB. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1183–1192, 2008     

Phase separation and polymer crystallization in a poly(4‐methyl‐1‐pentene)–dioctylsebacate–dimethylphthalate system via thermally induced phase separation

The effects of the polymer concentration and quenching temperature on the phase separation, the membrane morphology and polymer crystallization behavior in a poly(4‐methyl‐1‐pentene) (TPX)‐dioctylsebacate (DOS)‐dimethylphthalate (DMP) system via thermally induced phase separation were studied with a pseudobinary phase diagram, with the weight ratio of DOS:DMP = 1:1. SEM was used to observe the membrane morphology and structure, whereas the TPX crystallization behavior was studied with DSC and WAXD. Liquid‐liquid phase separation occurred, although quenching under the crystallization temperature. As the quenching temperature decreased, the pore size decreased, with better connected pore structure formed. The membranes quenched at 333 and 363 K showed good cellular structures, with an average pore size of about 2.3μm, whereas the pores of the membranes quenched at 393 and 423 K were not well formed, with some lamellar crystals on the inner side. The diluent assisted the mobility of the polymer chain, which improved the polymer crystallization. Dual‐melting‐peak behavior occurred for all the samples studied here. As the quenching temperature increased, the first peak of the melting trace moved to a higher temperature, whereas the second one stayed almost the same. The flexibility of the TPX main chain was restricted by the side groups, which allowed liquid‐liquid phase separation to occur first when quenched below the equilibrium crystallization temperature. This allowed primary and secondary crystallization, which was responsible for the dual‐melting‐peak behavior. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 153–161, 2007     

Analysis of the complex thermal behavior of poly(L‐lactic acid) film. I. Samples crystallized from the glassy state

The melting behavior of poly(L ‐lactic acid) film crystallized from the glassy state, either isothermally or nonisothermally, was studied by wide angle X‐ray diffraction (WAXD), small angle X‐ray scattering (SAXS), differential scanning calorimetry (DSC), and temperature‐modulated differential scanning calorimetry (TMDSC). Up to three crystallization and two melting peaks were observed. It was concluded that these effects could largely be accounted for on the basis of a “melt‐recrystallization” mechanism. When molecular weight is low, two melting endotherms are readily observed. But, without TMDSC, the double melting phenomena of high molecular weight PLLA is often masked by an exotherm just prior to the final melting, as metastable crystals undergo melt‐recrystallization during heating in the DSC. The appearance of a double cold‐crystallization peak during the DSC heating scan of amorphous PLLA film is the net effect of cold crystallization and melt‐recrystallization of metastable crystals formed during the initial cold crystallization. Samples cold‐crystallized at 80 and 90 °C did not exhibit a long period, although substantial crystallinity developed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3200–3214, 2006     

Probing multiple melting behaviors in poly(ethylene naphthalene 2,6‐dicarboxylate) with different thermal histories by simultaneous wide‐angle and small‐angle X‐ray scattering

A simultaneous wide‐angle and small‐angle X‐ray scattering study of two poly(ethylene naphthalene 2,6‐dicarboxylate) samples crystallized from the glassy state at different annealing temperatures for different annealing times was carried out with synchrotron radiation. Either single or dual melting was induced in the samples, as confirmed by differential scanning calorimetry (DSC). The correlation function and interface distribution function were calculated to evaluate microstructural parameters such as the long spacing, the thickness of the amorphous and crystalline phases, and the width of the size distributions. The sample with dual melting behavior exhibited an abrupt increase of all microstructural parameters at temperatures above the melting of the lowest endotherm, whereas the sample revealing a single melting endotherm did not show such a sudden change. This finding agrees with the concept that the appearance of two melting peaks in DSC traces can be explained by the dual lamellar stacking model. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 881–894, 2001     

The double melting behavior of a liquid crystalline polyimide derived from PMDA and 1,3‐bis[4‐(4′‐aminophenoxyl) cumyl] benzene

The double melting behavior of a thermotropic liquid crystalline polyimide was studied by means of differential scanning calorimetry (DSC), polarized light microscopy (PLM), transmission electron microscopy (TEM), wide‐angle X‐ray diffraction (WAXD), and small‐angle X‐ray scattering (SAXS). This liquid crystalline polyimide exhibited a normal melting peak around 278 °C and transformed into a smectic A phase. The smectic A phase changed to nematic phase upon heating to 298 °C, then became isotropic melt around 345 °C. The samples annealed or isothermally crystallized at lower temperature showed double melting endotherms during heating scan. The annealing‐induced melting endotherm was highly dependent on annealing conditions, whereas the normal melting endotherm was almost not influenced by annealing when the annealing temperature was low. Various possibilities for the lower melting endotherm are discussed. The equilibrium melting points of both melting peaks were extrapolated to be 283.2 °C. Combined analytical results showed that the double melting peaks were from the melting of the two types of crystallites generated from two crystallization processes: a slow and a fast one. Fast crystallization may start from the well‐aligned liquid crystal domains, whereas the slow one may be from the fringed or amorphous regions. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3018–3031, 2000     

Thermal and X‐ray analysis of polymorphic crystals,melting, and crystalline transformation in poly(butylene adipate)

Polymorphic crystals and complex multiple melting behavior in an aliphatic biodegradable polyester, poly(butylene adipate) (PBA), were thoroughly examined by wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). Further clarification on mechanisms of multiple melting peaks related to polymorphic crystal forms in PBA was attempted. More stable α‐form crystal is normally favored for crystallization from melt at higher temperatures (31–35 °C), or upon slow cooling from the melt; while the β‐form is the favored species for crystallization at low temperatures (25–28 °C). We further proved that PBA crystallization could also result in all α‐form even at low temperatures (25–28 °C) if it crystallized with the presence of prior α‐form nuclei. PBA packed with both crystal forms could display as many as four melting peaks (P1 ? P4, in ascending temperature order). However, PBA initially containing only the α‐crystal exhibited dual melting peaks of P1 and P3, which are attributed to dual lamellar distributions of the α‐crystal. By contrast, PBA initially containing only the β‐crystal could also exhibit dual melting peaks (P2 and P4) upon scanning. While P2 is clearly associated with melting of the initial β‐crystal, the fourth melting peak (P4), appearing rather broad, was determined to be associated with superimposed thermal events of crystal transformation from β‐ to α‐crystal and final re‐melting of the new re‐organized α‐crystal. Crystal transformation from one to the other or vice versa, lamellae thickening, annealing at molten state, and influence on crystal polymorphism in PBA were analyzed. Relationships and mechanisms of dual peaks for isolate α‐ or β‐crystals in PBA are discussed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1662–1672, 2005     

Temperature‐modulated differential scanning calorimetry studies on the origin of double melting peaks in isothermally melt‐crystallized poly(L‐lactic acid)

In this work, the melting behaviors of nonisothermally and isothermally melt‐crystallized poly(L ‐lactic acid) (PLLA) from the melt were investigated with differential scanning calorimetry (DSC) and temperature‐modulated differential scanning calorimetry (TMDSC). The isothermal melt crystallizations of PLLA at a temperature in the range of 100–110 °C for 120 min or at 110 °C for a time in the range of 10–180 min appeared to exhibit double melting peaks in the DSC heating curves of 10 °C/min. TMDSC analysis revealed that the melting–recrystallization mechanism dominated the formation of the double melting peaks in PLLA samples following melt crystallizations at 110 °C for a shorter time (≤30 min) or at a lower temperature (100, 103, or 105 °C) for 120 min, whereas the double lamellar thickness model dominated the formation of the double melting peaks in those PLLA samples crystallized at a higher temperature (108 or 110 °C) for 120 min or at 110 °C for a longer time (≥45 min). © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 466–474, 2007     

Origin of double melting behavior of poly(p‐phenylene succinate)

The origin of double melting behavior of poly(p‐phenylene succinate) (PPSc) was investigated by differential scanning calorimetry (DSC) and wide‐angle X‐ray diffraction. As‐polymerized PPSc showed two melting peaks: the low melting (LM) and high melting (HM) peaks at 286 and 311 °C, respectively. When PPSc was annealed at 270 °C, the LM peak constantly shifted toward higher temperatures and grew in its area with annealing time, and eventually merged into the HM peak located at 308 °C. X‐ray diffractograms of PPSc annealed at 270 °C became sharper with increasing the annealing time while the peak positions did not change. The X‐ray diffractograms obtained from the LM and the HM peak exhibited the same diffraction peaks. It was concluded from these results that the double melting behavior of PPSc is due to the distribution of crystals having the same crystal form but differing in size and perfection. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1868–1871, 2000     

New insights into the multiple melting behaviors of the semicrystalline ethylene‐hexene copolymer: Origins of quintuple melting peaks

A semicrystalline ethylene‐hexene copolymer (PEH) was subjected to a simple thermal treatment procedure as follows: the sample was isothermally crystallized at a certain isothermal crystallization temperature from melt, and then was quenched in liquid nitrogen. Quintuple melting peaks could be observed in heating scan of the sample by using differential scanning calorimeter (DSC). Particularly, an intriguing endothermic peak (termed as Peak 0) was found to locate at about 45 °C. The multiple melting behaviors for this semicrystalline ethylene‐hexene copolymer were investigated in details by using DSC. Wide‐angle X‐ray diffraction (WAXD) technique was applied to examine the crystal forms to provide complementary information for interpreting the multiple melting behaviors. Convincing results indicated that Peak 0 was due to the melting of crystals formed at room temperature from the much highly branched ethylene sequences. Direct heating scans from isothermal crystallization temperature (T_c, 104–118 °C) were examined for comparison, which indicated that the multiple melting behaviors depended on isothermal crystallization temperature and time. A triple melting behavior could be observed after a relatively short isothermal crystallization time at a low T_c (104–112 °C), which could be attributed to a combination of melting of two coexistent lamellar stack populations with different lamellar thicknesses and the melting‐recrystallization‐remelting (mrr) event. A dual melting behavior could be observed for isothermal crystallization with both a long enough time at a low T_c and a short or long time at an intermediate T_c (114 °C), which was ascribed to two different crystal populations. At a high T_c (116–118 °C), crystallizable ethylene sequences were so few that only one single broad melting peak could be observed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2100–2115, 2008