Antibacterial poly(ethylene glycol) hydrogels from combined epoxy‐amine and thiol‐ene click reaction

Antibacterial hydrogels containing quaternary ammonium (QA) groups were prepared via a facile thiol‐ene “click” reaction using multifunctional poly(ethylene glycol) (PEG). The multifunctional PEG polymers were prepared by an epoxy‐amine ring opening reaction. The chemical and physical properties of the hydrogels could be tuned with different crosslinking structures and crosslinking densities. The antibacterial hydrogel structures prepared from PEG Pendant QA were less well‐defined than those from PEG Chain‐End QA. Furthermore, functionalization of the PEG‐type hydrogels with QA groups produced strong antibacterial abilities against Staphylococcus aureus, and therefore has the potential to be used as an anti‐infective material for biomedical devices. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 656–667     

Electrochemical characterization of hydrogels for biomimetic applications

Hydrogels are increasingly being recognized as having potential in bio‐compatible applications. In previous work, we investigated the feasibility of poly(ethylene glycol)‐dimethacrylate (PEG‐1000‐DMA) and poly(ethylene glycol)‐diacrylate (PEG‐400‐DA) polymerized using either a chemical initiator (C) or a photoinitiator (P) to encapsulate and stabilize biomimetic membranes for novel separation technologies or biosensor applications. In this paper, we have investigated the electrochemical properties of the hydrogels used for membrane encapsulation. Specifically, we studied the crosslinked hydrogels by using electrochemical impedance spectroscopy (EIS), and we demonstrated that chemically crosslinked hydrogels had lower values for the effective electrical resistance and higher values for the electrical capacitance compared with hydrogels with photoinitiated crosslinking. Transport numbers were obtained using electromotive force measurements and demonstrated that at low salt concentrations, both PEG‐400‐DA‐C and PEG‐400‐DA‐P hydrogels presented an electropositive character whereas PEG‐1000‐DMA‐P was approximately neutral and PEG‐1000‐DMA‐C showed electronegative character. Sodium transport numbers approached the bulk NaCl electrolyte value at high salt concentrations for all hydrogels, indicating screening of fixed charges in the hydrogels. The average salt diffusional permeability 〈P_s〉 and water permeability 〈P_w〉 were found to correlate with EIS results. Both PEG‐1000‐DMA‐C and PEG‐400‐DA‐C had higher 〈P_s〉 and 〈P_w〉 values than PEG‐1000‐DMA‐P and PEG‐400‐DA‐P hydrogels. In conclusion, our results show that hydrogel electrochemical properties can be controlled by the choice of polymer and type of crosslinking used and that their water and salt permeability properties are congruent with the use of hydrogels for biomimetic membrane encapsulation. Copyright © 2011 John Wiley & Sons, Ltd.     

PEG–PLGA copolymers bearing carboxylated side chains: Novel hydrogels with enhanced crosslinking via ionic interactions

Novel water‐soluble amphiphilic block copolymers with pendant carboxylic acid groups are synthesized and used for the preparation of ionically crosslinked hydrogels. d ,l ‐Lactide (DLLA) and l ?3‐(2‐benzyloxycarbonyl)ethyl‐1,4‐dioxane‐2,5‐dione (BED) are copolymerized at different ratios via organo‐catalyzed ring‐opening polymerization using a hydroxyl‐terminated poly(ethylene glycol) (PEG–OH) macroinitiator. Dynamic light‐scattering experiments show that, at low concentrations, aqueous solutions of these PEG‐P(BED‐DLLA) copolymers form micelles and aggregates. At higher concentrations, thermo‐sensitive gels are obtained, exhibiting a reversible gel‐to‐sol transition upon a temperature increase. Ionic interactions between the COOH groups and metal ions (Cu²⁺ or Ca²⁺) are shown to significantly shift the gel–sol transition to higher temperatures. Thus, the introduction of COOH groups significantly enhances the water solubility of the amphiphilic PEG–polyester copolymer and allows additional crosslinking interactions to form functionalized hydrogels with improved physical properties, making this new class of hydrogels interesting for various applications. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1222–1227     

Semi‐interpenetrating polymer networks composed of poly(N‐isopropyl acrylamide) and polyacrylamide hydrogels

Three series of semi‐interpenetrating polymer networks, based on crosslinked poly(N‐isopropyl acrylamide) (PNIPA) and 1 wt % nonionic or ionic (cationic and anionic) linear polyacrylamide (PAAm), were synthesized to improve the mechanical properties of PNIPA gels. The effect of the incorporation of linear polymers into responsive networks on the temperature‐induced transition, swelling behavior, and mechanical properties was studied. Polymer networks with four different crosslinking densities were prepared with various molar ratios (25:1 to 100:1) of the monomer (N‐isopropyl acrylamide) to the crosslinker (methylenebisacrylamide). The hydrogels were characterized by the determination of the equilibrium degree of swelling at 25 °C, the compression modulus, and the effective crosslinking density, as well as the ultimate hydrogel properties, such as the tensile strength and elongation at break. The introduction of cationic and anionic linear hydrophilic PAAm into PNIPA networks increased the rate of swelling, whereas the presence of nonionic PAAm diminished it. Transition temperatures were significantly affected by both the crosslinking density and the presence of linear PAAm in the hydrogel networks. Although anionic PAAm had the greatest influence on increasing the transition temperature, the presence of nonionic PAAm caused the highest dimensional change. Semi‐interpenetrating polymer networks reinforced with cationic and nonionic PAAm exhibited higher tensile strengths and elongations at break than PNIPA hydrogels, whereas the presence of anionic PAAm caused a reduction in the mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3987–3999, 2004     

Thermoresponsive drug controlled release from chitosan‐based hydrogel embedded with poly(N‐isopropylacrylamide) nanogels

A facile synthetic strategy was developed for the preparation of thermoresponsive nanocomposite hydrogels comprising crosslinked chitosan (CS) networks and poly(N‐isopropylacrylamide) [p(NIPAAm)] nanogels. First, thermoresponsive p(NIPAAm) nanogels were synthesized via emulsion polymerization. The p(NIPAAm) nanogels were introduced into methacrylamide CS (MC) solution and the free‐radical initiated crosslinking reaction of MC produced nanogel‐embedded hydrogels. The last step involves the loading of the antibacterial model drug levofloxacin (LFX) into the prepared nanocomposite hydrogels by allowing the preformed hydrogels to swell to equilibrium in the drug's aqueous solution. The integration of p(NIPAAm) nanogel into CS networks facilitates thermoresponsive release of LFX with an enhancement of the drug‐loading capacity within the hydrogel. Notably, thermoresponsive drug‐release was achieved without unwarranted modification of the hydrogel's dimension and shape, although an increase in temperature caused the collapse of the p(NIPAAm) nanogels. The thermoresponsive property of the investigated nanocomposite hydrogel is beneficial and may offer broad opportunities for drug temperature‐triggered release for clinical applications. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1907–1914     

Reducible polyethylenimine hydrogels with disulfide crosslinkers prepared by michael addition chemistry as drug delivery carriers: Synthesis,properties, and in vitro release

Degradable hydrogels crosslinked with disulfide bonds were prepared by Michael addition between amine groups of branched polyethylenimine and carbon–carbon double bonds of N,N′‐bis(acryloyl)cystamine. The influences of the chemical composition of the resulted hydrogels on their properties were examined in terms of morphology, surface area, swelling kinetics, and degradation. The hydrogels were uniformly crosslinked and degraded into water‐soluble polymers in the presence of the reducing agent of dithiothreitol, which improved the control over the release of encapsulated drug. The degradation of hydrogels can trigger the release of encapsulated molecules, as well as facilitate the removal of empty vehicles. Results obtained from in vitro drug release suggested that the disulfide crosslinked hydrogels exhibited an accelerated release of encapsulated drug in dithiothreitol‐containing PBS buffer solution. Moreover, the drug release rate decreased gradually with increasing crosslinking density. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4074–4082, 2009     

Synthesis and characterization of acrylamide/acrylic acid hydrogels crosslinked using a novel diacrylate of glycerol to produce multistructured materials

In this work we propose a new crosslinking agent and the method to use it for the synthesis of acrylate based hydrogels. The use of this diacrylate of glycerol, synthesized in our laboratory, allows the generation of materials with well defined micro‐structures in the dry state, unique meso‐ and macro‐structures during swelling, and enhanced mechanical properties and swelling capacity in water. These properties depend on the crosslinking agent concentration, as well as synthesis thermal history. Poly(acrylamide‐co‐acrylic acid) hydrogels are commonly crosslinked with N, N′‐methylenebisacrylamide or N‐isopropylacrylamide. Here we obtain and use a new crosslinking agent, obtained from the reaction between glycerol and acrylic acid to produce a Diacrylate of glycerol (DAG). Two synthesis methods at equivalent molar ratio of acrylamide/acrylic acid (AM/AA) were analyzed. The mechanical properties, the swelling capacity, and the morphology at microscale of these hydrogels showed a well defined transition at a critical concentration of crosslinking agent. DAG induces the generation of hydrogels with hierarchichal structure. The micro‐structure surface morphology was investigated by scanning electron microscopy, the meso‐structure by polarized light microscopy and the macro‐structure by CCD imaging. The hydrogels with hierarchical structures showed improved mechanical properties when compared with structureless hydrogels. Control of the microstructure allows the generation of materials for different applications, i.e. templates or smart materials that interact with electromagnetic radiation. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2667–2679, 2008     

Synthesis and characterization of novel biodegradable unsaturated poly(ester amide)/poly(ethylene glycol) diacrylate hydrogels

A series of novel biodegradable hydrogels were designed and synthesized from four types of unsaturated poly(ester amide) (UPEA) and poly(ethylene glycol) diacrylate (PEG‐DA) precursors by UV photocrosslinking. These newly synthesized biodegradable UPEA/PEG‐DA hydrogels were characterized by their gel fraction (G_f), equilibrium swelling ratio (Q_eq), compressive modulus, and interior morphology. The effect of the precursor feed ratio (UPEAs to PEG‐DA) on the properties of the hydrogels was also studied. The incorporation of UPEA polymers into the PEG‐DA hydrogels increased their hydrophobicity, crosslinking density (denser network), and mechanical strength (higher compressive modulus) but reduced Q_eq. When different types of UPEA precursors were coupled with PEG‐DA at the same feed ratio (20 wt %), the resulting hydrogels had similar Q_eq values and porous three‐dimensional interior morphologies but different G_f and compressive modulus values. These differences in the hydrogel properties were correlated to the chemical structures of the UPEA precursors; that is, the different locations of the >C?C< double bonds in individual UPEA segments resulted in their different reactivities toward PEG‐DA to form hydrogels. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3932–3944, 2005     

Solid polymer electrolytes I,preparation, characterization,and ionic conductivity of gelled polymer electrolytes based on novel crosslinked siloxane/poly(ethylene glycol) polymers

A series of crosslinked siloxane/poly(ethylene glycol) (Si–PEG) copolymers were synthesized from the reactive methoxy‐functional silicone resin (Si resin) and PEGs with different molecular weights via two kinds of crosslinking reactions during an in situ curing stage. One of the crosslinking reactions is the self‐condensation between two methoxy groups in the Si resin, and another one is an alkoxy‐exchange reaction between the methoxy group in the Si resin and the OH group in PEG. The synthesized crosslinked copolymers were characterized by Fourier transform infrared spectroscopy, DSC, and ¹³C NMR. The crosslinked copolymers were stable in a moisture‐free environment, but the Si? O? C linkages were hydrolyzed in humid conditions. The gel‐like solid polymer electrolytes (SPEs) were prepared by impregnating these crosslinked Si–PEG copolymers in a propylene carbonate (LiClO₄/PC) solution. The highest conductivity reached 2.4 × 10^?4 S cm^?1 at 25 °C and increased to 8.7 × 10^?4 S cm^?1 at 85 °C. The conductivities of these gel‐type SPEs were affected by the content of LiClO₄/PC, the molecular weights of PEGs, and the weight fraction of the Si resin. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2051–2059, 2004     

Photoswitchable PEG‐CA hydrogels and factors that affect their photosensitivity

The photoswitching behavior of polyethylene glycol‐based hydrogels was determined by monitoring the changes in their swellability and absorption spectra upon exposure to alternating wavelengths of irradiation. Highly hydrophilic PEG‐based hydrogels were prepared by the irradiation of a cinnamylidene acetate‐terminated PEG solution (PEG‐CA). The degree of swelling of the PEG‐CA hydrogels was predictably modulated by alternating the wavelength of exposing irradiation. Exposing the PEG‐CA gels to >300 nm irradiation resulted in the decrease of their swellability, while short exposure to 254 nm led to more hydrophilic gels. That is, the physical properties of the PEG‐CA gels can be controlled by the selection of wavelength of irradiation. Interestingly, it was found that 254 nm irradiation could not only lead to the photoscission of the PEG‐CA gels, but also initiate a crosslinking reaction between PEG‐CA monomers. On the contrary, only photocrosslinking via a cyclobutane ring formation was observed under >300‐nm irradiation. Finally, the factors that could affect an efficient photoswitching behavior of the PEG‐CA gels were investigated. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1466–1476, 2000     

Amphiphilic membranes crosslinked and reinforced by POSS

This article concerns the synthesis and characterization of novel tricomponent amphiphilic membranes consisting of hydrophilic poly(ethylene glycol) (PEG) and hydrophobic polydimethylsiloxane (PDMS) segments cocrosslinked and reinforced by octasilane polyhedral oligomeric silsesquioxane (octasilane‐POSS) cages. Rapid and efficient network synthesis was effected by cocrosslinking diallyl‐telechelic PEG (A‐PEG‐A) and divinyl‐telechelic PDMS (V‐PDMS‐V) with pentamethylpentacyclosiloxane (D₅H), using Karstedt's catalyst in conjunction with Et₃N cocatalyst and water. Films were prepared by pouring charges in molds and crosslinking by heating at 60 °C for several hours. The films were characterized by sol fractions and equilibrium swelling both in hexane and water, extent of crosslinking, contact angle hysteresis, oxygen permeability, thermogravimetric analysis, and mechanical properties. The crosslinking of octasilane‐POSS achieved by the same catalyst system was studied in separate experiments. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4337–4352, 2004     

Polyester hydrogels with swelling properties controlled by the polymer architecture,molecular weight,and crosslinking agent

Hydrogels of poly(1,5‐dioxepan‐2‐one) and hydrogels of block copolymers of poly(1,5‐dioxepan‐2‐one) and poly(L ‐lactide) were synthesized. Both star‐shaped polymers and linear polymers were polymerized with ring‐opening polymerization and crosslinked in situ with a tetrafunctional acid chloride (1,2,3,4‐cyclopentane tetracarboxylic acid chloride) or a difunctional acid chloride (succinyl chloride). Different network architectures were synthesized in this way. The initial monomer concentrations and the molecular weights of the macromonomers were also altered. The networks were characterized with ¹H NMR and differential scanning calorimetry, and the swelling abilities of the different hydrogels were investigated in water and dichloromethane. The ratio of the monomer to the crosslinking agent was assessed by the quantification of the signal intensities in the ¹H NMR spectra of the swelled network and agreed with the theoretical crosslinking density. Both the homopolymers of 1,5‐dioxepan‐2‐one and the copolymers of 1,5‐dioxepan‐2‐one and L ‐lactide swelled to a high degree in water. The swelling properties of the materials could be varied over a broad range by changes in the architecture, molecular weight, and content of the precursor in the network. Star‐shaped poly(1,5‐dioxepan‐2‐one) crosslinked with a difunctional acid chloride had the highest degree of swelling among the different homopolymer hydrogels. This network also had the lowest glass‐transition temperature because of the flexible units in the structure. The same trends found for the homopolymer hydrogels were also seen in the hydrogels with block copolymers. The hydrogels swelled enormously in dichloromethane, and as in water, the star‐shaped copolymer crosslinked with a difunctional acid chloride had the highest degree of swelling. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1296–1305, 2003     

Characterization of well‐defined poly(ethylene glycol) hydrogels prepared by thiol‐ene chemistry

Considering the large number of applications for hydrogels, a better understanding of the relation between molecular structure and mechanical properties for well‐defined hydrogel is essential. A new library has been compiled of poly(ethylene glycol) polymers (PEG) of different length end functionalized with diallyl, dithiol, and dimethacrylate, and crosslinked with complementary trifunctional crosslinkers. In this study, the hydrogels were initially analyzed by FT‐Raman and NMR to study the conversion ratio of the functional groups. The effects of solvent type, solid content concentration, curing time and length of the PEG chains on the final leaching, swelling and tensile properties of the hydrogels were studied. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Facile synthesis and crosslinking reaction of trifunctional five‐membered cyclic carbonate and dithiocarbonate

The trifunctional five‐membered cyclic carbonate 2 and dithiocarbonate 3 were successfully synthesized by the reaction of trifunctional epoxide 1 with carbon dioxide and carbon disulfide, respectively. The crosslinking reactions of 2 with p‐xylylenediamine or hexamethylenediamine were carried out in dimethyl sulfoxide at 100 °C for 48 h to produce the corresponding crosslinked poly(hydroxyurethane)s quantitatively. The crosslinking reactions of 3 with both p‐xylylenediamine and hexamethylenediamine, followed by acetylation of thiol moiety, produced the corresponding crosslinked poly(thioester–thiourethane)s quantitatively. The obtained crosslinked poly(hydroxyurethane)s were thermally more stable than the analogous crosslinked poly(thioester–thiourethane)s, probably because of less thermal stability of thiourethane moiety than hydroxyurethane moiety. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5983–5989, 2004     

Poly(ethylene glycol)–poly(L‐lactide) star block copolymer hydrogels crosslinked by metal–ligand coordination

The aqueous solution behavior and thermoreversible gelation properties of pyridine‐end‐functionalized poly(ethylene glycol)–poly(L ‐lactide) (PEG–(PLLA)₈–py) star block copolymers in the presence of coordinating transition metal ions were studied. In aqueous solutions, the macromonomers self‐assembled into micelles and micellar aggregates at low concentrations and formed physically crosslinked, thermoreversible hydrogels above a critical gel concentration (CGC) of 8% w/v. In the presence of transition metal ions like Cu(II), Co(II), or Mn(II), the aggregate dimensions increased. Above the CGC, the gel–sol transition shifted to higher temperatures due to the formation of additional crosslinks from intermolecular coordination complexes between metal ions and pyridine ligands. Furthermore, as an example, PEG–(PLLA)₈–py hydrogels stabilized by Mn(II)–pyridine coordination complexes were more resistant against degradation/dissolution when placed in phosphate buffered saline at 37 °C when compared with hydrogels prepared in water. Importantly, the stabilizing effect of metal–ligand coordination was noticeable at very low Cu(II) concentrations, which have been reported to be noncytotoxic for fibroblasts in vitro. These novel PEG–(PLLA)₈–py metallo‐hydrogels, which are the first systems to combine metal–ligand coordination with the advantageous properties of PEG–PLLA copolymer hydrogels, are appealing materials that may find use in biomedical as well as environmental applications like the removal of heavy metal ions from waste streams. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Konjac glucomannan‐graft‐acrylic acid hydrogels containing azo crosslinker for colon‐specific delivery

In this article, the synthesis and characterization of novel hydrogel systems designed for colon‐targeting drug delivery are reported. The gels were composed of konjac glucomannan, copolymerized with acrylic acid, and crosslinked by the aromatic azo agent bis(methacryloylamino)‐azobenzene. The influence of various parameters on the dynamic and equilibrium swelling ratios (SRs) of the hydrogels was investigated. It is shown that the SR was inversely proportional to the grafting degree of acrylic acid and the content of bis(methacryloylamino)‐azobenzene. The dependence of SR on the pH indicates that obtained hydrogels are potential for drug delivery to colon. It was possible to modulate the degree of swelling and the pH sensitivity of the gels by changing crosslinking density of the polymer. The main chain of hydrogels can be degraded by β‐glycosidase which is abundant in colon. They can be in vitro degraded for 73% in a month by Cereflo® and 86% in 20 days by Mannaway25L. We have also prepared the hydrogels that loaded with bovine serum albumin about 1.5%, 3%, 9%, and 20% by weight. In vitro release of model drug bovine serum albumin was studied in the presence of Mannaway25L or Fungamyl®800L in pH 7.4 phosphate buffer at 37 °C. The drug release can be controlled by the biodegradation of the hydrogels. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4370–4378, 2004     

Tough and self‐recoverable hydrogels crosslinked by triblock copolymer micelles and Fe3+ coordination

Tough hydrogels have great potentials in soft robotics, artificial muscles, tissue replacement, and so on. Here we introduce novel tough hydrogels crosslinked by triblock copolymer (F127DA) micelles and metal coordination. The gels showed outstanding tensile strength (∼1–11 MPa), toughness (∼4–32 MJ m⁻³), and excellent self‐recovery properties (∼56.8–87.2% toughness recovery in 9 min at room temperature). The mechanical and self‐recovery properties could be manipulated by varying contents of micelles and/or COO⁻ groups. Dynamic mechanical analysis of the hydrogels revealed apparent activation energy and relaxations for both physical interactions. In situ small‐angle X‐ray scattering measurements on hydrogels upon stretching revealed micelle deformations. XPS measurements on hydrogels before and after stretching revealed significant changes in the binding energy of Fe³⁺ ions in the gels, suggesting the rupture of coordination bonds. The experimental results strongly suggest a synergistic effect from the micelle‐crosslinking and Fe³⁺–COO⁻ coordination on the strength, toughness, and self‐recovery of the hydrogels. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 865–876     

Hyaluronan/Collagen Hydrogels with Sulfated Hyaluronan for Improved Repair of Vascularized Tissue Tune the Binding of Proteins and Promote Endothelial Cell Growth

Innovative biomaterial‐based concepts are required to improve wound healing of damaged vascularized tissues especially in elderly multimorbid patients. To develop functional hydrogels as 3D cellular microenvironments and as carrier or scavenging systems, e.g., for mediator proteins or proinflammatory factors, collagen fibrils are embedded into a network of photo‐crosslinked acrylated hyaluronan (HA), chondroitin sulfate (CS), or sulfated HA (sHA). After lyophilization, the gels show a porous structure and an improved stability against degradation via hyaluronidase. Gels with CS and sHA bind significantly more lysozyme than HA/collagen gels and retard its release. The proliferation and metabolic activity of endothelial cells are significantly increased on sHA gels compared to CS‐ or only HA‐containing hydrogels. These findings highlight the potential of HA/collagen hydrogels with sulfated glycosaminoglycans to tune the protein binding and release behavior and to directly modulate cellular response. This can be easily translated into biomimetic biomaterials with defined properties to stimulate wound healing.     

One‐pot fabrication of robust interpenetrating hydrogels via orthogonal click reactions

Interpenetrating polymer network (IPN) hydrogels have been fabricated through a facile one‐pot approach from tetra/bifunctional telechelic macromonomers with epoxy, amine, azide, and alkyne groups by orthogonal double click reactions: epoxy‐amine reaction and copper‐catalyzed azide‐alkyne cycloaddition. Both the crosslinked networks are simultaneously constructed in water from the biocompatible poly (ethylene glycol)‐based macromonomers. The crosslinking density of each network was finely tuned by the macromonomer structure, permitting control of network molecular weights between crosslinks of the final gels. Compared to corresponding single network gels, the IPN gels containing both tightly and loosely crosslinked networks exhibited superior mechanical properties with shear moduli above 15 kPa and fracture stresses over 40 MPa. The synthetic versatility of this one‐pot approach will further establish design principles for the next generation of robust hydrogel materials. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1459–1467     

Effects of annealing and the addition of PEG on the PVA based hydrogel by gamma ray

Poly(vinyl alcohol) (PVA) is an interesting material with good biocompatibility, high elasticity and hydrophilic characteristics. PVA hydrogels have been formed through chemical crosslinking with aldehyde, photopolymerization and physical crosslinking with freeze-thawing. In this study, crosslinked hydrogels based on PVA, and poly(ethylene glycol) (PEG) were prepared by gamma-ray irradiation, and then annealed at 120 °C. The properties of a hydrogel such as gel fraction, swelling behavior, gel strength as a function of PEG content and annealing time were investigated. Also, the thermal behaviors were examined by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The gel fraction decreases with an increase in PEG content and decrease in annealing time. The tensile strength increases with an increase in annealing time. The thermal behaviors have shown different patterns according to the annealing time. The improved properties suggest that PVA/PEG blend hydrogel can be a good candidate for applications in the articular cartilage.