Fourth‐order hydrodynamic contribution to the polymer self‐diffusion coefficient

A hydrodynamic scattering treatment of interacting polymer chains is extended to obtain the five‐point chain–chain–chain–chain–chain hydrodynamic interaction tensor. The tensor is used to calculate the second‐order concentration correction to the self‐diffusion coefficient of a polymer in solution. The self‐similarity assumption of the hydrodynamic scaling model of polymer dynamics is tested against these calculations. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1663–1670, 2004     

Thiol‐ene photopolymerization of polymer‐derived ceramic precursors

The liquid, ceramic precursor monomer VL20 was copolymerized with a thiol monomer in a traditional radical thiol‐ene photopolymerization. Polymerization occurred via addition of the thiol functional group to the vinyl silazane functional group in a 1:1 ratio consistent with a step‐growth polymerization. Gelation occurred at a high conversion of functional groups (70%) consistent with an average molecular weight and functionality of 560 and 1.7, respectively, for VL20 monomers. Initiatorless photopolymerization of the thiol‐VL20 system also occurred upon irradiation at either 365 or 254 nm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1752–1757, 2004     

Synthesis of end‐functionalized AB copolymers. II. Synthesis and characterization of carboxyl‐terminated poly(ethylene glycol)–poly(amino acid) block copolymers

AB block copolymers composed of hydrophilic poly(ethylene glycol) (PEG) and hydrophobic poly(amino acid) with a carboxyl group at the end of PEG were synthesized with α‐carboxylic sodium‐ω‐amino‐PEG as a macroinitiator for the ring‐opening polymerization of N‐carboxy anhydride. Characterizations by ¹H NMR, IR, and gel permeation chromatography were carried out to confirm that the diblock copolymers were formed. In aqueous media this copolymer formed self‐associated polymer micelles that have a carboxyl group on the surface. The carboxyl groups located at the outer shell of the polymeric micelle were expected to combine with ligands to target specific cell populations. The diameter of the polymer micelles was in the range of 30–80 nm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3527–3536, 2004     

Amphiphilic block copolymers of high‐molecular‐weight poly(ethylene oxide) and either ε‐caprolactone or γ‐methyl‐ε‐caprolactone: Synthesis and characterization

Ethylene oxide (EO) has been block‐polymerized with both ε‐caprolactone (ε‐CL) and γ‐methyl‐ε‐caprolactone (MCL) through the combination of the anionic polymerization of EO and the ring‐opening polymerization (ROP) of ε‐CL and MCL. ω‐Hydroxyl poly(ethylene oxide) has been reacted with triethylaluminum (OH/Al = 1) and converted into a macroinitiator for ROP of ε‐CL and MCL. In toluene at room temperature, this polymerization leads to a bimodal molecular weight distribution as a result of monomer insertion in only some of the aluminum alkoxide bonds. However, in a more polar solvent (methylene chloride) added with 1 equiv of a Lewis base (pyridine), the expected diblock is formed selectively, and this indicates that aggregation of the active species in toluene is responsible for a macroinitiator efficiency of less than 1. A series of amphiphilic diblock copolymers with poly(ε‐caprolactone) (semicrystalline) and poly(γ‐methyl‐ε‐caprolactone) (amorphous) as the hydrophobic blocks have been prepared and characterized with size exclusion chromatography, ¹H NMR, IR, and wide‐angle X‐ray scattering. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1132–1142, 2004     

Energy‐damping behaviors of poly(methyl acrylate‐co‐divinylbenzene) microspheres coated with a porous nickel–phosphorus layer

Hybrid microspheres of poly(methyl acrylate‐co‐divinylbenzene) (PMADVB) with a thin and porous nickel–phosphorus (Ni–P) alloy layer were prepared via suspension polymerization and electroless nickel plating. The characterization of pristine and nickel‐coated microspheres was carried out with a differential scanning calorimeter and a scanning electron spectroscope equipped with an energy‐dispersive system. The glass‐transition range of Ni–P‐coated PMADVB was broadened and extended in the higher temperature direction. This effect allowed the PMADVB network to embrace more diversified energy states of the segment motion, this being a desired feature for damping sound waves. The low‐frequency (100–1000‐Hz) sound absorption behavior of the microspheres was tested with a sound attenuation kit. Besides the testing of their low‐frequency damping performance, an investigation into the ultrasonic‐wave (～35 kHz) absorption feature of the microspheres was conducted through chemical means; that is, the attenuation to the ultrasonic wave with respect to the unprotective situation was assessed through the chemisorption extent of copper ions on a biomass adsorbent. The Ni–P deposition layer was found to augment the damping capacity of the polymer network. The alloy layer was determined to cause an expansion of the glass‐transition range of PMADVB and its wave‐scattering capability because this layer was made up of submicrometer metallic grains. In this work, the particulars of the metal–polymer interactions were associated with a core–shell structure. The metal outer layer was thought to create a spherical temperature field inside the PMADVB network, and concerted motions of the polymer segments resulted. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2710–2723, 2004     

Metallocenic copolymers of ethylene and 5,7‐dimethylocta‐1,6‐diene: Structural characterization and mechanical behavior

The relationship between the structure and mechanical properties has been established for several copolymers of ethylene and 5,7‐dimethylocta‐1,6‐diene synthesized with a metallocene catalyst. A dependence on the composition and polymerization temperature has been found. The branches cannot be incorporated into the orthorhombic crystal lattice, and consequently, structural parameters such as the crystallinity and crystal size are considerably affected as the 5,7‐dimethylocta‐1,6‐diene content increases in the copolymers. The viscoelastic relaxations have been analyzed and compared with those exhibited by high‐density polyethylene (HDPE). The β relaxation does not appear in HDPE and is exclusively seen in the copolymers. As the 5,7‐dimethylocta‐1,6‐diene content rises, the intensity of this process is increased, and its location is shifted to a lower temperature up to comonomer contents of approximately 6–8 mol % in the copolymers. On the other hand, the α mechanism associated with motion within the crystalline regions is also moved to a lower temperature and its intensity is diminished as the 5,7‐dimethylocta‐1,6‐diene molar fraction increases in the copolymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3797–3808, 2004     

Interfacial effects in organophilic montmorillonite–poly(ϵ‐caprolactone) nanocomposites

In the last few years much progress has been made in the development of hybrid polymer–inorganic filler nanocomposites. Nevertheless, many questions remain. The comprehension of the structure and the interactions at the polymer–nanofiller interface are crucial to foresee and control the properties of nanocomposites. Because of the high surface ratio of the inorganic nanofiller, the interface is expected to have a prevailing role in determining the nanocomposite properties. In this study we use X‐ray photoelectron spectroscopy (XPS) as a tool for the surface characterization of an organophilic montmorillonite/poly(ε‐caprolactone) exfoliated nanocomposite. The XPS core levels of the nanocomposite have been compared with those obtained from its precursors, and analyzed as reference compounds to evaluate eventual differences attributable to the polymer–nanofiller interfacial interactions. The XPS investigation has allowed us to propose a qualitative model of possible interface interactions between poly(ε‐caprolactone) and the organo‐modified montmorillonite. The model is substantiated by Fourier transform infrared spectroscopy (FTIR). © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3907–3919, 2004     

Facile approach to polyurea/malonamide dendrons via a selective ring‐opening addition reaction of azetidine‐2,4‐dione

A bifunctional compound [(4‐isocyanato‐4′(3,3‐dimethyl ‐2,4‐dioxo‐acetidino)diphenylmethane] (MIA) has been used as a building block for the synthesis of novel polyurea/malonamide dendrons. This is based on selectively sequential addition reactions of amines to isocyanato‐azetidine‐2,4‐diones. After incorporation of the MIA onto the growing dendrons, rapid entry into polyurea/malonamide dendrons was achieved via a convergent route with the processing advantages of easy purification, high yield, and rapid synthesis. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 682–688, 2005     

Fluorescent probes for monitoring the pulsed‐laser‐induced photocuring of poly(urethane acrylate)‐based adhesives

Fluorescence spectroscopy was used to study the kinetics of polymerization of acrylic adhesive formulations exposed to a 355‐nm pulsed emission from an Nd‐YAG laser. Nine fluorescent probes were used for monitoring the laser curing, showing different sensitivities. In general, the fluorescence intensity emission increased as crosslinking occurred. In addition, solvatochromic fluorescent probes showed a blueshift in their emission. A relative method was applied for the evaluation of the polymerization rates in three different acrylic systems. Special features of pulsed‐laser‐induced polymerization were treated in detail, such as the influence of the laser pulse frequency and the incident laser beam intensity. The polymerization rate slowed down as the pulse repetition rate decreased. An inhibition period due to oxygen quenching was observed, and it was highly dependent on the laser repetition rate and the nature of the photoinitiator. The effect of the laser beam intensity on the kinetics of such fast reactions was studied. In general, increasing the laser energy improved the rate of polymerization. The degree of cure improved as the polymerization rate increased as a result of faster crosslinking, rather than relaxation volume kinetics. Moreover, a saturation rate effect occurred that depended on the photoinitiator. The different behaviors of the two photoinitiators in the curing of the same acrylic formulation was explained on the basis of primary radical termination. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1227–1238, 2004     

Ring‐opening polymerization of L‐lactide by rare‐earth tris(4‐tert‐butylphenolate) single‐component initiators

The ring‐opening polymerization of L ‐lactide initiated by single‐component rare‐earth tris(4‐tert‐butylphenolate)s was conducted. The influences of the rare‐earth elements, solvents, temperature, monomer and initiator concentrations, and reaction time on the polymerization were investigated in detail. No racemization was found from 70 to 100 °C under the examined conditions. NMR and differential scanning calorimetry measurements further confirmed that the polymerization occurred without epimerization of the monomer or polymer. A kinetic study indicated that the polymerization rate was first‐order with respect to the monomer and initiator concentrations. The overall activation energy of the ring‐opening polymerization was 79.2 kJ mol^?1. ¹H NMR data showed that the L ‐lactide monomer inserted into the growing chains with acyl–oxygen bond cleavage. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6209–6215, 2004     

Photopolymerization of 1,6‐hexanedioldiacrylate initiated by three‐component systems based on N‐arylphthalimides

Three‐component photoinitiators comprised of an N‐arylphthalimide, a diarylketone, and a tertiary amine were investigated for their initiation efficiency of acrylate polymerization. The use of an electron‐deficient N‐arylphthalimide resulted in a greater acrylate polymerization rate than an electron‐rich N‐arylphthalimide. Triplet energies of each N‐arylphthalimide, determined from their phosphorescence spectra, and the respective rate constants for triplet quenching by the N‐arylphthalimide derivatives (acquired via laser flash photolysis) indicated that an electron–proton transfer from an intermediate radical species to the N‐arylphthalimide (not energy transfer from triplet sensitization) is responsible for generating the initiating radicals under the conditions and species concentrations used for polymerization. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4009–4015, 2004     

Ultrahigh‐molecular‐weight‐polyethylene‐fiber surface treatment by electron‐beam‐irradiation‐induced graft polymerization and its effect on adhesion in a styrene–butadiene rubber matrix

Aiming to develop a high‐performance fiber‐reinforced rubber from styrene–butadiene rubber (SBR), we applied a special technique using electron‐beam (EB)‐irradiation‐induced graft polymerization to ultrahigh‐molecular‐weight‐polyethylene (UHMWPE) fibers. The molecular interaction between the grafted UHMWPE fibers and an SBR matrix was studied through the evaluation of the adhesive behavior of the fibers in the SBR matrix. Although UHMWPE was chemically inert, two monomers, styrene and N‐vinyl formamide (NVF), were examined for graft polymerization onto the UHMWPE fiber surface. Styrene was not effective, but NVF was graft‐polymerized onto the UHMWPE fibers with this special method. A methanol/water mixture and dioxane were used as solvents for NVF, and the effects of the solvents on the grafting percentage of NVF were also examined. The methanol/water mixture was more effective. A grafting percentage of 16.4% was the highest obtained. This improved the adhesive force threefold with respect to that of untreated UHMWPE fibers. These results demonstrated that EB irradiation enabled graft polymerization to occur even on the inert surface of UHMWPE fibers. However, the mechanical properties of the fibers could be compromised according to the dose of EB irradiation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2595–2603, 2004     

Synthesis and characterization of soluble polyimides derived from 2′,5′‐bis(3,4‐dicarboxyphenoxy)‐p‐terphenyl dianhydride

A novel bis(ether anhydride) monomer, 2′,5′‐bis(3,4‐dicarboxyphenoxy)‐p‐terphenyl dianhydride, was synthesized from the nitro displacement of 4‐nitrophthalonitrile by the phenoxide ion of 2′,5′‐dihydroxy‐p‐terphenyl, followed by alkaline hydrolysis of the intermediate bis(ether dinitrile) and cyclodehydration of the resulting bis(ether diacid). A series of new poly(ether imide)s bearing laterally attached p‐terphenyl groups were prepared from the bis(ether anhydride) with various aromatic diamines via a conventional two‐stage process that included ring‐opening polyaddition to form the poly(amic acid)s followed by thermal or chemical imidization to the poly(ether imide)s. The inherent viscosities of the poly(amic acid) precursors were in the range of 0.62–1.26 dL/g. Most of the poly(ether imide)s obtained from both routes were soluble in polar organic solvents, such as N,N‐dimethylacetamide. All the poly(ether imide)s could afford transparent, flexible, and strong films with high tensile strengths. The glass‐transition temperatures of these poly(ether imide)s were recorded as between 214 and 276 °C by DSC. The softening temperatures of all the poly(ether imide) films stayed in the 207–265 °C range according to thermomechanical analysis. For all the polymers significant decomposition did not occur below 500 °C in nitrogen or air atmosphere. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1008–1017, 2004     

Microwave syntheses of poly(ε‐caprolactam‐co‐ε‐caprolactone)

Microwave irradiation was applied to synthesize poly(ε‐caprolactam‐co‐ε‐caprolactone) directly from the anionic catalyzed ring opening of two cyclic monomers, ε‐caprolactam and ε‐caprolactone using a variable frequency microwave furnace, programmed to a set temperature and controlled by a pulsed power on–off system. Dielectric properties of ε‐caprolactam, ε‐caprolactone, and their mixture were measured in the microwave range from 0.4 to 3 GHz, showing that both ε‐caprolactam and ε‐caprolactone exhibited effective absorption of microwave energy to induce a fast chemical reaction. The microwave induced anionic copolymerization of ε‐caprolactam and ε‐caprolactone generated copoly(amide‐ester)s in yields as high as 70%. Conventional thermal and microwave copolymerization studies were also conducted for comparison with the microwave results. These studies demonstrated that an effective and efficient microwave method to copolymerize ε‐caprolactam with ε‐caprolactone in higher yield, higher amide content, and higher T_g 's, relative to the thermal process, has been developed. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1379–1390, 2000     

Synthesis and characterization of fluorescent poly[fluorene‐co‐phenylene‐1‐(di‐2‐pyridylamine)] copolymer and its Ru(II) complex

2,2′‐dipyridylamine substituted poly(fluorene‐co‐phenylene) copolymers with different concentrations of dipyridylamine have been synthesized by Suzuki polycondensation. These polymers were found to be soluble in organic solvents such as tetrahydrofuran, chloroform, and dimethylformamide. The photoluminescence of the copolymer was slightly blueshifted as the concentration of dipridylamine was increased. The introduction of dipyridylamine and the ruthenium complex into the polymer significantly improved the photoluminescence efficiency. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4838–4846, 2004     

Ion‐beam‐induced morphology on the surface of thin polymer films at low current density and high ion fluence

The effect of Xe⁺ bombardment on the surface morphology of four different polymers, polystyrene (PS), poly(phenylene oxide), polyisobutylene, and polydimethylsiloxane, was investigated in ion energy and fluence ranges of interest for secondary ion mass spectrometry depth‐profiling analysis. Atomic force microscopy (AFM) was applied to analyze the surface topography of pristine and irradiated polymers. AFM analyses of nonirradiated polymer films showed a feature‐free surface with different smoothness. We studied the influence of different Xe⁺ beam parameters, including the incidence angle, ion energy (660–4000 eV), current density (0.5 × 10² to 8.7 × 10² nA/cm²), and ion fluence (4 × 10¹⁴ to 2 × 10¹⁷ ion/cm²). Xe⁺ bombardment of PS with 3–4 keV at a high current density did not induce any change in the surface morphology. Similarly, for ion irradiation with lower energy, no surface morphology change was found with a current density higher than 2.6 × 10² nA/cm² and an ion fluence up to 4 × 10¹⁶ ion/cm². However, Xe⁺ irradiation with a lower current density and a higher ion fluence led to topography development for all of the polymers. The roughness of the polymer surface increased, and well‐defined patterns appeared. The surface roughness increased with ion irradiation fluence and with the decrease of the current density. A pattern orientation along the beam direction was visible for inclined incidence between 15° and 45° with respect to the surface normal. Orientation was not seen at normal incidence. The surface topography development could be explained on the basis of the balance between surface damage and sputtering induced by the primary ion beam and redeposition–adsorption from the gas phase. Time‐of‐flight secondary ion mass spectrometry analyses of irradiated PS showed strong surface modifications of the molecular structure and the presence of new material. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 314–325, 2001     

Brominated poly(isobutylene‐co‐para‐methylstyrene) (BIMS)‐clay nanocomposites: Synthesis and characterization

In this work, preparation and properties of different nanoclays modified by organic amines (octadecyl amine, a primary amine, and hexadecyltrimethylammonium bromide, a tertiary amine) and brominated polyisobutylene‐co‐paramethylstyrene (BIMS)‐clay nanocomposites are reported. The clays and the rubber nanocomposites have been characterized with the help of Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and X‐ray diffraction (XRD). The X‐ray diffraction peaks observed in the range of 3 °–10 ° for the modified clays disappear in the rubber nanocomposites. TEM photographs show predominantly exfoliation of the clays in the range of 12 ± 4 nm in the BIMS. In the FTIR spectra of the nanocomposites, there are common peaks of virgin rubber as well as those of the clays. Excellent improvement in mechanical properties like tensile strength, elongation at break, and modulus is observed on incorporation of the nanoclays in the BIMS. Structure‐property correlation in the above nanocomposites is attempted. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4489–4502, 2004     

Modification of carboxyl‐functionalized single‐walled carbon nanotubes with biocompatible,water‐soluble phosphorylcholine and sugar‐based polymers: Bioinspired nanorods

We report here the successful functionalization of single‐walled carbon nanotubes with bioinspired sugar and phosphocholine polymeric structures via surface‐initiated atom transfer radical polymerization. The surface‐polymer‐coated carbon nanotubes have been systematically analyzed by Raman, infrared, ultraviolet–visible, and nuclear magnetic resonance spectroscopy and high‐resolution transmission electron microscopy, which give strong evidence of successful functionalization. The successful aqueous dispersion of the functionalized carbon nanotubes also indicates that functionalization has been achieved. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6558–6568, 2006     

Zeolite‐supported metallocene catalyst for ethylene/1‐hexene copolymerization

Commercial zeolite acid mordenite was thermally treated for use as a support for bis(n‐butyl‐cyclopentadienyl)zirconium dichloride [(n‐BuCp)₂ZrCl₂] for the further evaluation of ethylene/1‐hexene copolymerization. The polymerization time, temperature, and solvent, as well as the addition of tri(isobutyl)aluminum in the hexane medium, were evaluated. The catalytic activity and 1‐hexene content in the copolymer synthesized with the supported system were very near those obtained with the homogeneous precursor. A comonomer effect was observed for both systems. The polymerization rate profiles were obtained for ethylene polymerization, and the activation energy and monomer reactivity were calculated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3038–3048, 2004     

Synthesis and inhibition performance of a polymer‐supported inhibitor

The synthesis of a polymer‐supported inhibitor (PSI) and its inhibition performance for free‐radical polymerization are reported for the first time. A special method has been devised to synthesize PSI with pure and abundant hydroquinone (HQ) groups anchored onto the polymer surface. A thin HQ/acetone (AC) solution is sandwiched between two polymer films. Under ultraviolet irradiation, AC as an photoinitiator quickly and effectively grafts HQ onto the polymer surface. PSI has been characterized with ultraviolet–visible and attenuated total reflectance/Fourier transform infrared spectroscopy. For potential applications, PSI has been used to inhibit the thermal polymerization of styrene and methyl methacrylate. The corresponding inhibition performance has been investigated through the measurement of the induction period with the dilatometer method. With the same absolute amount, the maximum inhibition ability of PSI approaches half that of a free inhibitor. Increasing the dispersion degree of PSI is favorable for the enhancement of the inhibition ability. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4074–4083, 2004