Exclusion effect of carbon dioxide on the crystallization of polypropylene

We investigated the crystallization growth of isotactic polypropylene under carbon dioxide (CO₂) at various CO₂ pressures and temperatures by in situ observation with a digital high‐fidelity microscope and a specially designed high‐pressure visualized cell. The fibrils within the spherulite were distorted and branched by crystallization under CO₂ at pressures higher than 2 MPa, and this suggested the exclusion of CO₂ from the growth front of the fibrils. The spherulite growth rate (G) at 140 °C increased with the CO₂ pressure, attained a maximum value around 0.3 MPa, and then decreased. Above 6 MPa, it became slower than that under air at the ambient pressure. An analysis of the crystallization kinetics by the Hoffman–Lauritzen theory revealed that the pressure dependence of G could be ascribed to the change in the transportation rate of crystallizable molecules (β_g) with pressure; that is, β_g increased and then decreased with pressure. The increase in β_g at a low pressure was caused by the plasticizing effect of CO₂, whereas the decrease in β_g at a high pressure was due to the exclusion of CO₂ from the crystal growth front. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1565–1572, 2004     

Melting behavior of a poly(ether‐block‐amide) copolymer melt‐crystallized under quiescent,isothermal conditions

Segmented poly(ether‐block‐amide) copolymers are typically known as polyamide‐based thermoplastic elastomers consisting of hard, crystallizable polyamide block and flexible, amorphous polyether block. The melting characteristics of a poly(ether‐block‐amide) copolymer melt‐crystallized under various quiescent, isothermal conditions were calorimetrically investigated using differential scanning calorimetry (DSC). For such crystallized copolymer samples, their crystalline structures under ambient condition and the structural evolutions upon heating from ambient to complete melting were characterized using ambient and variable‐temperature wide‐angle X‐ray diffractometry (WAXD), respectively. It was observed that dependent of specific crystallization conditions, the copolymer samples exhibited one, two, or three melting endotherms. The ambient WAXD results indicated that all melt‐crystallized copolymer samples only exhibited γ‐form crystals associated with the hexagonal habits of the polyamide homopolymer, whereas variable‐temperature WAXD data suggested that upon heating from ambient, a melt‐crystallized copolymer might exhibit so‐called Brill transition before complete melting. Based on various DSC and variable‐temperature WAXD experimental results obtained in this study, the applicability of different melting mechanisms that might be responsible for multiple melting characteristics of various crystallized PEBA copolymer samples were discussed. It was postulated that the low (T _m1) endotherm was primarily because of the disruption of less thermally stable, short‐range ordered structure of amorphous polyamide segments of the copolymer, which was only formed after the completion of primary crystallization via so‐called annealing effects. The intermediate (T_m2) and high (T_m3) endotherms were attributed to the melting of primary crystals within polyamide crystalline microdomains of the copolymer. The appearance of these two melting endotherms might be somehow complicated by thermally induced Brill transition. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2035–2046, 2008     

Crystallization and morphology of star-shaped polyethylenoxyde-b-polycaprolactone under high pressure carbon dioxide

Atomic force microscopy（AFM）,wide-angle X-ray diffraction（WAXD） and differential scanning calorimetry are used to analyze the crystallization morphology and melting behavior of 4-arm PEO-b-PCL under high-pressure CO₂.It is demonstrated that CO₂ has certain effect on the melting and crystallization behavior of the samples.After crystallization under CO₂ at 4 MPa,spherulites with concentric ring-banded structure are formed which are composed of crystals with periodic thickness variation,and the band distance decreases with increasing treatment pressure.Due to the plasticization effect of CO₂,depression of the melting temperature is observed with sorption of CO₂ in polymers.     

CO2‐delayed crystallization of isotactic polypropylene: A kinetic study

The effect of CO₂ on the nonisothermal crystallization of isotactic polypropylene (iPP) was studied with high‐pressure differential scanning calorimetry at cooling rates of 0.2–5 °C/min. CO₂ significantly delayed the melt crystallization of iPP, and both the crystallization temperature and the heat of crystallization decreased with increasing CO₂ pressure. The crystallization rate of iPP, as characterized by the half‐time, was also prolonged by the presence of CO₂. With a modified Ozawa model developed by Seo, the Avrami crystallization exponent n of iPP was calculated. This value was depressed by the addition of CO₂ and was strongly dependent on the CO₂ pressure at low cooling rates. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1518–1525, 2003     

Compressed‐gas‐induced crystallization in tert‐butyl poly(ether ether ketone)

tert‐Butyl‐substituted poly(ether ether ketone) (tBuPEEK), which does not undergo crystallization with thermal annealing, crystallizes readily when treated with compressed CO₂. The dissolved CO₂ causes a reduction in the glass‐transition temperature of the polymer–gas system and enhances the chain mobility of the macromolecules, thereby bringing about crystallization. In the presence of CO₂, crystallization is increasingly favored with increasing CO₂ pressure and treatment temperature. The melting point of tBuPEEK crystals increases linearly with the CO₂ pressure applied in the treatment, indicating an increase in the order and/or size of the crystals. The extent of crystallinity increases when small amounts of methanol or dichloromethane are used as a cosolute with CO₂. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1505–1512, 2001     

Analysis of the complex thermal behavior of poly(L‐lactic acid) film. II. Samples crystallized from the melt

The complex thermal behavior of poly(l ‐lactic acid) films crystallized from the melt, either isothermally or nonisothermally, was studied by differential scanning calorimetry (DSC), wide angle X‐ray diffraction, and small angle X‐ray scattering. The variation of the thermal behavior with crystallization temperature, time, and cooling rate was documented and analyzed. After nonisothermal crystallization at low cooling rates that develop high crystallinity, an obvious double melting peak appears at modest heating rates (e.g., 10 °C/min). At higher heating rates, these samples exhibit only single melting. However, an unusual form of double melting occurs under the majority of the conditions studied under either isothermal or nonisothermal conditions. In this case, double melting is marked by the appearance of a recrystallization exotherm just prior to the final melting that obscures the observation of the melting of the crystals formed during the initial crystallization process. The occurrence of double melting in melt‐crystallized samples was concluded to be the result of a melt‐recrystallization process occurring during the subsequent DSC heating scan; it is a function of crystalline perfection, not the initial crystallinity, nor whether or not the crystallization reached completion at the crystallization temperature. Many other very interesting observations are also discussed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3378–3391, 2006     

Influence of deformation on irreversible and reversible crystallization of poly(ethylene‐co‐1‐octene)

The effect of uniaxial deformation and subsequent relaxation at ambient temperature on irreversible and reversible crystallization of homogeneous poly(ethylene‐co‐1‐octene) with 38 mol % 1‐octene melt‐crystallized at 10 K min was explored by calorimetry, X‐ray scattering, and Fourier transform infrared spectroscopy. At 298 K, the enthalpy‐based crystallinity of annealed specimens increased irreversibly by stress‐induced crystallization from initially 15% to a maximum of, at least, 19% when a permanent set of more than 200% was attained. The crystallinity increased by formation of crystals of pseudohexagonal structure at the expense of the amorphous polymer, and as a result of destruction of orthorhombic crystals. The stress‐induced increase of crystallinity was accompanied by an increase in the apparent specific heat capacity from 2.44 to about 2.59 J g^?1 K^?1, which corresponds to an increase of the total reversibility of crystallization from, at least, 0.10 to 0.17% K^?1. The specific reversibility calculated for 100% crystallinity increased from 0.67 to 0.89% K^?1 and points to a changed local equilibrium at the interface between the crystal and amorphous phases. The deformation resulted in typical changes of the phase structure and crystal morphology that involve orientation and destruction of crystals as well as the formation of fibrils. The effect of the decrease of the entropy of the strained melt on the reversibility of crystallization and melting is discussed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1223–1235, 2002     

Melting behavior in blends of isotactic polypropylene and a liquid crystalline polymer

The influence of low contents of a liquid crystalline polymer on the crystallization and melting behavior of isotactic polypropylene (iPP) was investigated using electron and optical microscopy, differential scanning calorimetry, and X-ray diffraction. In pure iPP, the α modification was found, whereas for iPP/Vectra blends at Vectra concentration <5%, both α and β forms were observed. The amount of β phase varied from 0.23 to 0.16. Optical microscopy showed that Vectra was able to nucleate both α and β forms. Non-isothermal crystallization produces a material with a strong tendency for recrystallization of the α and β forms (αα′ and ββ′ recrystallization) leading to double endotherms for both crystalline forms in DSC thermograms. Melting thermograms after isothermal crystallization at low temperatures showed a similar behavior. At values of T_c > 119 °C for the α form and T_c > 125 °C for the β form, only one melting endotherm was observed because enough perfect crystals, not susceptible to recrystallization, were obtained. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1949–1959, 2004     

Crystallization and melting of isotactic polypropylene crystallized from quiescent melt and stress‐induced localized melt

Temperature dependency of crystalline lamellar thickness during crystallization and subsequent melting in isotactic polypropylene crystallized from both quiescent molten state and stress‐induced localized melt was investigated using small angle X‐ray scattering technique. Both cases yield well‐defined crystallization lines where inverse lamellar thickness is linearly dependent on crystallization temperature with the stretching‐induced crystallization line shifted slightly to smaller thickness direction than the isothermal crystallization one indicating both crystallization processes being mediated a mesomorphic phase. However, crystallites obtained via different routes (quiescent melt or stress‐induced localized melt) show different melting behaviors. The one from isothermal crystallization melted directly without significant changing in lamellar thickness yielding well‐defined melting line whereas stress‐induced crystallites followed a recrystallization line. Such results can be associated with the different extent of stabilization of crystallites obtained through different crystallization routes. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 957–963     

Effect of MMT,SiO2, CaCO3, and PTFE nanoparticles on the morphology and crystallization of poly(vinylidene fluoride)

The crystallization and melting behaviors of poly (vinylidene fluoride) (PVDF) with small amount of nanoparticles (1 wt %), such as montmorillonite (MMT), SiO₂, CaCO₃, or polytetrafluoroethylene (PTFE), directly prepared by melt‐mixing method were investigated by scanning electron microscopy (SEM), polarizing optical microscopy, Fourier transform infrared spectroscopy, wide angle X‐ray diffraction (WAXD), and differential scanning calorimetry (DSC). The nanoparticle structure and the interactions between PVDF molecule and nanoparticle surface predominated the crystallization behavior and morphology of the PVDF. Small amount addition of these four types of nanoparticles would not affect the original crystalline phase obtained in the neat PVDF sample (α phase), but accelerated the crystallization rate because of the nucleation effect. In these four blend systems, MMT or PTFE nanoparticles could be well applied for PVDF nanocomposite preparation because of stronger interactions between particle surface and PVDF molecules. The nucleation enhancement and the growth rate of the spherulites were decreased in the order SiO₂ > CaCO₃ > PTFE > MMT. The melting and recrystallization of PVDF was found in MMT addition sample, because of the special ways of ordering of the PVDF chains. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Isothermal melt and cold crystallization kinetics of poly(aryl ether ketone ether ketone ketone)

The isothermal melt and cold crystallization kinetics of poly(aryl ether ketone ether ketone ketone) are investigated by differential scanning calorimetry over two temperature regions. The Avrami equation describes the primary stage of isothermal crystallization kinetics with the exponent n ≈ 2 for both melt and cold crystallization. With the Hoffman–Weeks method, the equilibrium melting point is estimated to be 406 °C. From the spherulitic growth equation proposed by Hoffman and Lauritzen, the nucleation parameter (K_g) of the isothermal melt and cold crystallization is estimated. In addition, the K_g value of the isothermal melt crystallization is compared to those of the other poly(aryl ether ketone)s. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1992–1997, 2000     

Thermal properties and influence of orientation on crystalline morphologies in stereoblock polypropylene and related elastomers

Atomic force microscopy (AFM), small angle X‐ray scattering (SAXS), temperature modulated differential scanning calorimetry (TMDSC), variable heating rate DSC, an independent rapid heating rate method for melting points, and cyclic mechanical testing were used to study semicrystalline thermoplastic elastomeric polypropylenes (ELPPs) and related semicrystalline polyolefins including ethylene copolymers. Low crystallinity (ca., 9 and 15%) ELPP samples were studied by AFM in the nonoriented and melt‐oriented states. AFM images taken as a function of time after quenching of a melt‐drawn and highly nucleated film resolved details of secondary crystallization involving lateral growth on the ordered row‐nucleated structures. For nonoriented films, isothermal melt crystallization at high temperatures (110 °C) led to similar features for the two ELPPs. The dominant crystalline morphology studied by AFM consisted of small (several nm in width) granular crystallites organized into immature but large spherulites spanning tens of microns. A striking cross‐hatch morphology was detected in regions of the surface in 110 °C crystallized samples, which is contrasted with melt‐drawn films where row nucleated structures dominated the morphology in the film under no external stress. AFM was also used to monitor the morphological changes that occurred as the films were stretched at 25 °C. Break‐down of lamellae was observed, resulting in oriented narrow fibrils. Cyclic stress‐strain curves showed the expected result where lower crystallinity ELPPs had higher recoverable levels of set after both 100 and 500% elongation. TMDSC was used to resolve the broad melting and recrystallization regions in these low to medium crystallinity ELPP systems, and to contrast the results with ethylene copolymers. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Oxygen‐barrier properties of cold‐crystallized and melt‐crystallized poly(ethylene terephthalate‐co‐4,4′‐bibenzoate)

This study examined the oxygen‐transport properties of poly(ethylene terephthalate‐co‐bibenzoate) (PETBB55) crystallized from the melt (melt crystallization) or quenched to glass and subsequently isothermally crystallized by heating above the glass‐transition temperature (cold crystallization). The gauche–trans conformation of the glycol linkage was determined by infrared analysis, and the crystalline morphology was examined by atomic force microscopy. Oxygen solubility decreased linearly with volume fraction crystallinity. For melt‐crystallized PETBB55, extrapolation to zero solubility corresponded to an impermeable crystal with 100% trans glycol conformations, a density of 1.396 g cm^?3, and a heat of melting of 83 J g^?1. From the melt, PETBB55 crystallized as space‐filling spherulites with loosely organized lamellae and pronounced secondary crystallization. The morphological observations provided a structural model for permeability consisting of impermeable platelets randomly dispersed in a permeable matrix. In contrast, cold‐crystallized PETBB55 retained the granular texture of the quenched polymer despite the high level of crystallinity, as measured by the density and heat of melting. Oxygen solubility decreased linearly with volume fraction crystallinity, but zero solubility corresponded to an impermeable defective crystal with a trans fraction of 0.83 and a density of 1.381 g cm^?3. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2489–2503, 2002     

Correlation of the melting behavior and copolymer composition distribution of Ziegler–Natta‐catalyst and single‐site‐catalyst polyethylene copolymers

The multimodal differential scanning calorimetry melting endotherms observed for commercial linear low‐density polyethylenes are due to broad and multimodal short‐chain‐branching distributions. Multiple peaks, observed in melting endotherms of isothermally melt‐crystallized and compositionally homogeneous polyethylene copolymers are due to intrachain heterogeneity. This intrachain heterogeneity is quantified by the distribution of ethylene sequence lengths within the chains. These compositionally homogeneous copolymers undergo a primary crystallization, which produces a population of thicker lamellae, creating a network that places severe restrictions on segment transport in subsequent secondary crystallization, which produces a population of thinner crystals. The restrictions on segment transport imposed by the initial network created by the primary crystallization of thicker lamellae severely limits the total crystallinity achieved in the random copolymers studied. The solution crystallization of such copolymers produces a continuous distribution due to more facile segment transport in a dilute solution, in contradistinction to the multimodal distribution produced in the melt crystallization. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2800–2818, 2001     

Step‐like melting mechanisms of isothermally crystallized isotactic polypropylene

The complex melting behavior of isotactic polypropylene, after isothermal crystallization, was studied within the context of step‐like melting mechanisms which were previously proposed for high temperature polymers. The morphological characteristics of the melting process were also studied as a function of molecular weight, and close similarities were observed with respect to high temperature polymers. Positive birefringence crystals of low molecular weight samples developed double melting behavior in three steps. The first melting step was assigned to continuous melting of secondary crosshatch reversing lamellae, together with recrystallization of the remaining isothermal crystals. In the second melting step (first melting endotherm), crystals tended to lose their original coarse negative birefringence due to melting of secondary reversing branching. This effect rendered new, finer texture, but still negative birefringence crystals. In the third melting step (second melting endotherm), there was a combination of melting of two crystal populations, one consisting of the remaining fraction of reversing primary crystals, and the other consisting of nonreversing primary crystals. A crosshatch secondary branching model was therefore proposed to explain the overall results. Mixed birefringence spherulites of high molecular weight samples displayed similar, although proportional, behavior under identical crystallization and melting conditions corroborating the proposed melting mechanism. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2188–2200, 2008     

New insight into melting and crystallization behavior in semicrystalline poly(ethylene terephthalate)

After isothermal crystallization, poly(ethylene terephthalate) (PET) showed double endothermic behavior in the differential scanning calorimetry (DSC) heating scan. During the heating scans of semicrystalline PET, a metastable melt which comes from melting thinner lamellar crystal populations formed between the low and the upper endothermic temperatures. The metastable melt can recrystallize immediately just above the low melting temperature and form thicker lamellae than the original ones. The thickness and perfection depends on the crystallization time and crystallization temperature. The crystallization kinetics of this metastable melt can be determined by means of DSC. The kinetics analysis showed that the isothermal crystallization of the metastable PET melt proceeds with an Avrami exponent of n = 1.0 ∼ 1.2, probably reflecting one‐dimensional or irregular line growth of the crystal occurring between the existing main lamellae with heterogeneous nucleation. This is in agreement with the hypothesis that the melting peaks are associated with two distinct crystal populations with different thicknesses. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 53–60, 2000     

Enhanced electrical properties of highly oriented poly(vinylidene fluoride) films prepared by solid‐state coextrusion

Oriented poly(vinylidene fluoride) (PVDF) films with β‐form crystals have been commonly prepared by cold drawing of a melt‐quenched film consisting of α‐form crystals. In this study, we have successfully produced highly oriented PVDF thin films (20 µm thick) with β‐crystals and a high crystallinity (55–76%), by solid‐state coextrusion of a gel film to eight times the original length at an established optimum extrusion temperature of 160°C, some 10°C below the melting temperature. The resultant drawn films had a highly oriented (orientation function f_c = 0.993) fibrous structure, showing high mechanical properties of an extensional elastic modulus of 8.3 GPa and tensile strength of 0.84 GPa, along the draw direction. Such highly oriented and crystalline films exhibited excellent ferroelectric and piezoelectric properties. The square hysteresis loop was significantly sharper than that of a conventional sample. The sharp switching transient yielded the remnant polarization P_r of 90 mC/m², and the electromechanical coupling factor k_t was 0.24 at room temperature. These values are about 1.5 times greater than those of a conventional β‐PVDF film. Thus, solid‐state coextrusion near the melting point was found to be a useful technique for the preparation of highly oriented and highly crystalline β‐PVDF films with superior mechanical and electrical properties. The morphology of the extrudate relevant to such properties is discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2549–2556, 1999     

Crystallization and melting behaviour of poly(m-xylene adipamide)

The melting and crystallisation behaviour of poly(m-xylene adipamide) (MXD6) are investigated by using the conventional DSC, X-ray diffraction and polarised light microscopy. Triple, double or single melting endotherms are obtained in subsequent heating scan for the samples after isothermal crystallisation from the melt state at different temperatures. The lowest melting peak can be ascribed to the melting of secondary crystals. The melting of primary crystals causes the medium melting peak and the highest melting peak is attributed to the melting of recrystallised species formed during heating. Following the Hoffman–Weeks theory, the equilibrium melting temperature is equal to 250°C and the equilibrium melting enthalpy ΔH _m ⁰ to 175 J g^–1. Then, using the Lauritzen–Hoffmann theory of secondary crystallisation, the analyse of the spherulitic growth shows that the temperature of transition between the growing regimes II and III is equal to 176°C. Finally the Gibbs-Thomson relationship allows the determination of the distribution function of crystalline lamellae.     

Phase Transformation Behavior of Polylactide Probed by Small Angle Light Scattering and Calorimetry

Small angle light scattering (SALS) and differential scanning calorimetry DSC have been applied to investigate the melting of spherulites isothermally crystallized polylactide. At an isothermal crystallization temperature high enough, pure α‐phase crystals are formed. Exposed to a temperature gradient, the crystals first melt and then recrystallize before they finally melt. With decreasing crystallization temperature, an increasing fraction of polylactide is crystallizing in the less stable α ^′‐phase. α ^′‐crystals also melt upon increasing the temperature but recrystallize to the more stable α‐phase. A constant spherulite size is revealed by SALS for both processes, the α/α and α ^′/α melt‐recrystallization, until completion of the final melting, thereby supporting integrity of the spherulites throughout the entire processes. Joint DSC and SALS experiments demonstrate that the depolarized scattering invariant correlates with the heat flow recorded by DSC and thus offer an alternative measure for the degree of crystallinity. The following mechanism is identified for both processes: initial melting and recrystallization overlay each other. Crystallinity is not fully recovered upon recrystallization because only part of the original lamellae survives the melt‐recrystallization, though with an increased thickness. While lamellae are melting and reforming or simply transforming their phase, the spherulites survive the process until final melting. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1483–1495     

Effect of supercritical carbon dioxide on the crystallization and melting behavior of linear bisphenol A polycarbonate

The crystallization and melting behavior of bisphenol A polycarbonate treated with supercritical carbon dioxide (CO₂) has been investigated with differential scanning calorimetry. Supercritical CO₂ depresses the crystallization temperature (T_c) of polycarbonate (PC). The lower melting point of PC crystals increase nonlinearly with increasing treatment temperature. This indicates that the depression of T_c is not a constant at the same pressure. T_c decreases faster at a higher treatment temperature than at a lower temperature. The leveling off of the depression in T_c at higher pressures is due to the antiplasticization effect of the hydrostatic pressure of CO₂. The melting curves of PC show two melting endotherms. The lower melting peak moves to a higher temperature with increasing treatment temperature, pressure, and time. The higher temperature peak moves toward a higher temperature as the treatment temperature is increased, whereas this peak is independent of the treatment pressure, time, and heating rate. The double melting peaks observed for PC can be attributed to the melting of crystals with different stability mechanisms. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 280–285, 2004