Synthesis of phenylquinoxaline oligomers containing pendant electron‐donating and electron‐withdrawing groups

A series of extended 6‐substituted quinoxaline AB monomer mixtures, 2‐(4‐fluorophenyl)‐3‐[4‐(4‐hydroxyphenoxy)phenyl]‐6‐substituted quinoxaline and 3‐(4‐fluorophenyl)‐2‐[4‐(4‐hydroxyphenoxy)phenyl]‐6‐substituted quinoxaline, were prepared and polymerized to afford phenylquinoxaline oligomers. High‐molecular‐weight polymers could not be obtained because of the formation of cyclic oligomers. On the basis of matrix‐assisted laser desorption/ionization time‐of‐flight analysis and molecular modeling results, the formation of a cyclic dimer could be a favorable process resulting in low‐molecular‐weight oligomers. They were completely soluble and amorphous, with glass‐transition temperatures varying from 165 to 266 °C, and they had thermooxidative stability, with samples displaying 5% weight loss temperatures of 419–511 °C in nitrogen. The thermal properties of the monomers and resultant polymers dramatically depended on the polarity of the substituents. The monomers and resultant oligomers displayed high fluorescence in tetrahydrofuran solutions and N‐methyl‐2‐pyrrolidinone solutions, respectively. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6465–6479, 2005     

Solid‐state amidization and imidization reactions in vapor‐deposited poly(amic acid)

The condensation polymerization of 4,4′‐oxydianiline with pyromellitic dianhydride for the formation of poly(amic acid) and the subsequent imidization for the formation of polyimides were investigated for films prepared with vapor‐deposition polymerization techniques. Fourier transform infrared spectroscopy, thermal analysis, and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry of films at different temperatures indicated that additional solid‐state polymerization occurred before imidization. The experiments revealed that, upon vapor deposition, poly(amic acid) oligomers formed that had a number‐average molecular weight of about 1500 Da. Between 100–130 °C, these chains underwent an additional condensation reaction and formed slightly higher molecular weight oligomers. Calorimetry measurements showed that this reaction was exothermic [enthalpy of reaction (ΔH) ～ ?30 J/g] and had an activation energy of about 120 kJ/mol. The experimental ΔH values were compared with results from ab initio molecular modeling calculations to estimate the number of amide groups formed. At higher temperatures (150–300 °C), the imidization of amide linkages occurred as an endothermic reaction (ΔH ～ +120 J/g) with an activation energy of about 130 kJ/mol. The solid‐state kinetics depended on the reaction conversion as well as the processing conditions used to deposit the films. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5999–6010, 2004     

Novel miktofunctional initiator for the preparation of an ABC‐type miktoarm star polymer via a combination of controlled polymerization techniques

An ABC‐type miktoarm star polymer was prepared with a core‐out method via a combination of ring‐opening polymerization (ROP), stable free‐radical polymerization (SFRP), and atom transfer radical polymerization (ATRP). First, ROP of ϵ‐caprolactone was carried out with a miktofunctional initiator, 2‐(2‐bromo‐2‐methyl‐propionyloxymethyl)‐3‐hydroxy‐2‐methyl‐propionic acid 2‐phenyl‐2‐(2,2,6,6‐tetramethyl‐piperidin‐1‐yl oxy)‐ethyl ester, at 110 °C. Second, previously obtained poly(ϵ‐caprolactone) (PCL) was used as a macroinitiator for SFRP of styrene at 125 °C. As a third step, this PCL–polystyrene (PSt) precursor with a bromine functionality in the core was used as a macroinitiator for ATRP of tert‐butyl acrylate in the presence of Cu(I)Br and pentamethyldiethylenetriamine at 100 °C. This produced an ABC‐type miktoarm star polymer [PCL–PSt–poly(tert‐butyl acrylate)] with a controlled molecular weight and a moderate polydispersity (weight‐average molecular weight/number‐average molecular weight < 1.37). The obtained polymers were characterized with gel permeation chromatography and ¹H NMR. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4228–4236, 2004     

Anionic polymerization of N,N‐dialkyl‐2‐methylenebut‐3‐enamide: Effect of alkyl substituents on polymerization behavior

Anionic polymerizations of three 1,3‐butadiene derivatives containing different N,N‐dialkyl amide functions, N,N‐diisopropylamide (DiPA), piperidineamide (PiA), and cis‐2,6‐dimethylpiperidineamide (DMPA) were performed under various conditions, and their polymerization behavior was compared with that of N,N‐diethylamide analogue (DEA), which was previously reported. When polymerization of DiPA was performed at ?78 °C with potassium counter ion, only trace amounts of oligomers were formed, whereas polymers with a narrow molecular weight distribution were obtained in moderate yield when DiPA was polymerized at 0 °C in the presence of LiCl. Decrease in molecular weight and broadening of molecular weight distribution were observed when polymerization was performed at a higher temperature of 20 °C, presumably because of the effect of ceiling temperature. In the case of DMPA, no polymer was formed at 0 °C and polymers with relatively broad molecular weight distributions (M_w/M_n = 1.2) were obtained at 20 °C. The polymerization rate of PiA was much faster than that of the other monomers, and poly(PiA) was obtained in high yield even at ?78 °C in 24 h. The microstructure of the resulting polymers were exclusively 1,4‐ for poly(DMPA), whereas 20–30% of the 1,2‐structure was contained in poly(DiPA) and poly(PiA). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3714–3721, 2010     

Synthesis of polymers in aqueous solutions: Synthesis of polysulfide by reaction of bis(4‐mercaptophenyl) sulfide with bis(4‐chloro‐3‐nitrophenyl) sulfone using various bases in aqueous solutions

The polycondensation of bis(4‐mercaptophenyl) sulfide (BMPS) with bis(4‐chloro‐3‐nitrophenyl) sulfone (BCNPS) was examined using various organic or inorganic bases in mixed solvents of N‐methyl‐2‐pyrrolidone (NMP) with water or in plain water. The reaction of BMPS with BCNPS proceeded smoothly to give the corresponding polysulfide in mixed solvents of NMP with water at 60 °C using 1,8‐diazabicyclo[5.4.0]undecene‐7 as a base, although the rate of the reaction decreased gradually as the water in the solvent increased. Polysulfide can also be obtained by reaction in plain water using appropriate organic bases such as tripropylamine (TPA) or quinoline. The polysulfide with a number‐average molecular weight of 45,100 was synthesized in 62% yield when the reaction of BMPS with BCNPS was performed using TPA as a base at 60 °C for 48 h in plain water. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3399–3404, 2000     

Polymerization of styrene with tetramethylthiuram disulfide as an initiator in the presence of 2,2,6,6‐tetramethyl‐1‐piperidinyloxy

The bulk polymerization of styrene was investigated with tetramethylthiuram disulfide (TMTD) as an initiator in the presence of 2,2,6,6‐tetramethyl‐1‐piperidinyloxy (TEMPO) at 123 °C. The polymerization proceeded in a controlled/living way; that is, the polymerization rate was first‐order with respect to the monomer concentration, and the molecular weight increased linearly with conversion. The molecular weights of the polymers obtained were close to the theoretical values, and the molecular weight distributions were relatively low (weight‐average molecular weight/number‐average molecular weight = 1.1–1.3). The rate of polymerization with TMTD as an initiator was faster than that with benzoyl peroxide, and the rate was independent of the initial concentration of TMTD in the presence of TEMPO. The obtained polystyrene was functionalized with ultraviolet‐light‐sensitive ? SC(S)N(CH₃)₂ groups, which was characterized with ¹H NMR spectroscopy. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 543–551, 2005     

Synthesis and properties of blue light‐emitting,silicon‐containing,regio‐ and stereoregular conjugated polymers

This article concerns the hydrosilylation polyaddition of 1,4‐bis(dimethylsilyl)benzene ( 1 ) with 4,4′‐diethynylbiphenyl, 2,7‐diethynylfluorene ( 2b ), and 2,6‐diethynylnaphthalene with RhI(PPh₃)₃ catalyst. Trans‐rich polymers with weight‐average molecular weights (M_w's) ranging from 19,000 to 25,000 were obtained by polyaddition in o‐Cl₂C₆H₄ at 150–180 °C, whereas cis‐rich polymers with M_w's from 4300 to 34,000 were obtained in toluene at 0 °C–r.t. These polymers emitted blue light in 4–81% quantum yields. The cis polymers isomerized into trans polymers upon UV irradiation, whereas the trans polymers did not. The device having a layer of polymer trans‐ 3b obtained from 1 and 2b demonstrated electroluminescence without any dopant. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2774–2783, 2004     

Low‐temperature route to thermoplastic polyamide elastomers

Thermoplastic polyamide elastomers were obtained by polymerization of aminobenzoyl‐substituted telechelics derived from poly(tetrahydrofuran)‐diols (number‐average molecular weight: 1400 or 2000 g mol^?1) with several diacid dichlorides (terephthaloyl dichloride, 4,4′‐biphenyldicarbonyl dichloride, or 2,6‐naphthalenedicarbonyl dichloride) and chlorotrimethylsilane in N,N‐dimethylacetamide at 0–20 °C. The as‐prepared polymers had melting temperatures above 190 °C and exhibited elastic properties at room temperature, as evidenced by dynamic mechanical analysis and stress–strain measurements. The polymer with 2,6‐naphthalenedicarboxamide hard segments had the widest rubbery plateau within the series, the highest extension at break, and good recovery properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1449–1460, 2004     

Oligo‐Ortho‐Chloroazomethinephenol and its Metal Complexes: Synthesis,Characterization, Antimicrobial and Thermal Properties

The new Schiff base oligomer (oligo‐ortho‐chloroazomethinephenol) was synthesized by the condensation of ortho‐chloroaniline with oligosalicylaldehyde (OSA). Oligomer‐metal complexes of oligo‐ortho‐chloroazomethinephenol (OKAP) with Cu(II), Zn(II) and Co(II) were synthesized. The properties of OKAP and oligomer‐metal complexes were studied by elemental, UV‐Vis, ¹H‐NMR, FT‐IR, magnetic susceptibility analyses. The number average molecular weight and mass average molecular weight OKAP were found to be 1494 g · mol^?1 and 5418 g · mol^?1, respectively. Elemental analyses of oligomer‐metal complexes suggest that the ratio of metal to oligomer is 1∶2. The results indicate that the OKAP coordinate through azomethine nitrogen and phenolic oxygen to the metal ions. Antimicrobial activity of OKAP was tested against S. cerevisiae, B. subtilis, E. coli, K. pneumoniae, M. luteus and S. aureus. The thermal stabilities of the OKAP and oligomer‐metal complexes were compared by thermogravimetric (TG) analyses. According to TG, OKAP, and oligomer‐metal complexes were stable against temperature and thermooxidative decomposition. The weight losses of OKAP and oligomer‐metal complexes were found to be at 400 and 800°C at 20.2 and 50.0 (OKAP), 17.1 and 41.1 (Cu(II)), 13.4 and 38.5 (Zn(II)), 18.3 and 68.2 (Co(II)), %, respectively. Based on half degradation temperature (T_50%) parameters, Cu(II) and Zn(II) complexes were more resistant than the OKAP and Co(II) complex.     

Application of ketenes to well‐defined polyester synthesis. II. Synthesis of reactive polyester by living anionic polymerization of (4‐halophenyl)ethylketene

Novel ketenes, (4‐chlorophenyl)ethylketene and (4‐bromophenyl)ethylketene, were synthesized by dehydrochlorination of 2‐(4‐halophenyl)butanoyl chlorides, and their anionic polymerizations by lithium (4‐methoxyphenoxide) in tetrahydrofuran at ?20 °C were carried out to afford the corresponding polyesters with narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight < 1.3) quantitatively. Polymerizations with various feed ratios afforded the corresponding polyesters with predictable molecular weights and narrow molecular weight distributions. Kinetic studies of the polymerizations at ?78 °C revealed that the polymerization rates were apparently larger than that of ethylphenylketene, which is considered to be responsible for the enhanced electrophilicities of the monomers via the introduction of electron‐negative halogen atoms. Monomer conversion agreed with the first‐order kinetic equation. These results strongly support the living mechanism of this polymerization. The obtained polyesters were modified by a palladium‐catalyzed coupling reaction of the side‐chain 4‐halophenyl group with 4‐methoxyphenylboronic acid, demonstrating their potential as reactive polymers. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2093–2102, 2001     

3‐Phenylethynyl phthalimide end‐capped imide oligomers and the cured polymers

In the past decades, 4‐phenylethynyl phthalic anhydride (4‐PEPA) has been the most important endcapper used for thermoset polyimide. As the isomer of4‐PEPA, 3‐phenylethynyl phthalic anhydride (3‐PEPA) has attracted our interest. In this article, 3‐PEPA was synthesized and a comparative study with 4‐PEPA on curing temperature, curing rate, thermal and mechanical properties of oligomers and cured polymers was presented. The new phenylethynyl endcapped model compound, N‐phenyl‐3‐phenylethynyl phthalimide, was synthesized and characterized. The molecular structure of model compound was determined via single‐crystal X‐ray diffraction and the thermal curing process was investigated by Fourier transform infrared. Differential scanning calorimetry clearly showed that the model compound from 3‐PEPA had about 20 °C higher curing onset and peak temperature than the 4‐PEPA analog. This result was further proved by the dynamic rheological analysis that the temperature of minimum viscosity for oligomers end‐capped with 3‐PEPA was above 20 °C higher than that of the corresponding 4‐PEPA endcapped oligomers with the same calculated number average molecular weight. The cured polymer from 3‐PEPA displayed slightly higher thermal oxidative stability than those from 4‐PEPA by thermogravimetric analysis. The thermal curing kinetics of 3‐PEPA endcapped oligomer (OI‐5) and 4‐PEPA endcapped oligomer (OI‐6) fitted a first‐order rate law quite well and revealed a similar rate acceleration trend. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4227–4235, 2008     

Synthesis and properties of new aromatic polyimides based on 2,5‐bis(4‐amino‐2‐trifluoromethylphenoxy)‐tert‐butylbenzene and various aromatic dianhydrides

A novel, fluorinated diamine monomer, 2,5‐bis(4‐amino‐2‐ trifluoromethylphenoxy)‐tert‐butylbenzene ( II ) was synthesized through the nucleophilic substitution reaction of tert‐butylhydroquinone (t‐BHQ) and 2‐chloro‐5‐nitrobenzotrifluoride in the presence of potassium carbonate to yield the intermediate dinitro compound I , followed by catalytic reduction with hydrazine and Pd/C to afford diamine II . A series of fluorinated polyimides V were prepared from II with various aromatic dianhydrides ( III _a–f ) via the thermal imidization of poly(amic acid). Most of V _a–f could be soluble in amide‐type solvents and even in less polar solvents. These polyimide films showed tensile strengths up to 106 MPa, elongation at break up to 21%, and initial modulus up to 2.1 GPa. The glass‐transition temperature of V was recorded at 245–304 °C, the 10% weight loss temperatures were above 488 °C, and left more than 41% residue even at 800 °C in nitrogen. Low dielectric constants, low moisture absorptions, and higher and light‐colored transmittances were also observed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5424–5438, 2004     

Polymerization of β‐pinene with Schiff‐base nickel complexes catalyst: Synthesis of relatively high molecular weight poly(β‐pinene) at high temperature with high productivity

A series of easily accessible and stable Schiff‐base nickel complexes (complex 1 – 4 ) in conjunction with methylaluminoxane (MAO) were employed for the synthesis of relatively high molecular weight β‐pinene polymers at high temperature with high productivity. The ligand structure of the complex had a substantial effect on the polymerization in terms of the productivity and the molecular weight. With complex 4 in the presence of MAO, high molecular weight polymers of β‐pinene (M_n ～ 10,900) were obtained at 40 °C with an extremely high productivity up to 1.25 × 10⁷ g polyβ‐pinene/mol of Ni. ¹H NMR analyses showed that the obtained β‐pinene polymer was structurally identical to that formed by conventional cationic Lewis acid initiators. The polymerization was presumably initiated by the nickel cation formed by the reaction of the schiff‐base nickel complex and MAO, while the propagation proceeded in a manner typical for a conventional carbocationic polymerization process. Direct evidence for the carbocationic polymerization was offered by the fact that quenching of the polymerization with methanol at a low monomer conversion resulted in incorporation of a methoxyl end group into the polymer chain. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3739–3746, 2007     

Synthesis of well‐defined polymers end‐functionalized with crosslinkable aziridine groups by living anionic polymerization

Well‐defined end‐functionalized polystyrene, poly(α‐methylstyrene), and polyisoprene with polymerizable aziridine groups were synthesized by the termination reactions of the anionic living polymers of styrene, α‐methylstyrene, and isoprene with 1‐[2‐(4‐chlorobutoxy)ethyl]aziridine in tetrahydrofuran at ?78 °C. The resulting polymers possessed the predicted molecular weights and narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight < 1.1) as well as aziridine terminal moieties. The cationic ring‐opening polymerization of the ω‐monofunctionalized polystyrene having an aziridinyl group with Et₃OBF₄ gave the polymacromonomer, whereas the α,ω‐difunctional polystyrene underwent crosslinking reactions to afford an insoluble gel. Crosslinking products were similarly obtained by the reaction of the α,ω‐diaziridinyl polystyrene with poly(acrylic acid)‐co‐poly(butyl acrylate). © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4126–4135, 2005     

Chain‐growth condensation polymerization of 4‐aminobenzoic acid esters bearing tri(ethylene glycol) side chain with lithium amide base

Chain‐growth condensation polymerization of p‐aminobenzoic acid esters 1 bearing a tri(ethylene glycol) monomethyl ether side chain on the nitrogen atom was investigated by using lithium 1,1,1,3,3,3‐hexamethyldisilazide (LiHMDS) as a base. The methyl ester monomer 1a afforded polymer with low molecular weight and a broad molecular weight distribution, whereas the polymerization of the phenyl ester monomer 1b at ?20 °C yielded polymer with controlled molecular weight (M_n = 2800–13,400) and low polydispersity (M_w/M_n = 1.10–1.15). Block copolymerization of 1b and 4‐(octylamino)benzoic acid methyl ester ( 2 ) was further investigated. We found that block copolymer of poly 1b and poly 2 with defined molecular weight and low polydispersity was obtained when the polymerization of 1b was initiated with equimolar LiHMDS at ?20 °C and continued at ?50 °C, followed by addition of 2 and equimolar LiHMDS at ?10 °C. Spherical aggregates were formed when a solution of poly 1b in THF was dropped on a glass plate and dried at room temperature, although the block copolymer of poly 1b and poly 2 did not afford similar aggregates under the same conditions. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1357–1363, 2010     

Anionic polymerization of 4‐phenyl‐1‐buten‐3‐yne derivatives bearing electron‐withdrawing groups

The anionic polymerization of derivatives of 4‐phenyl‐1‐buten‐3‐yne was carried out to investigate the effect of substituents on the polymerization behavior. The polymerization of 4‐(4‐fluorophenyl)‐1‐buten‐3‐yne and 4‐(2‐fluorophenyl)‐1‐buten‐3‐yne in tetrahydrofuran at −78 °C with n‐BuLi/sparteine as an initiator gave polymers consisting of 1,2‐ and 1,4‐polymerized units in quantitative yields with ratios of 80/20 and 88/12, respectively. The molecular weights of the polymers were controlled by the ratio of the monomers to n‐BuLi, and the distribution was relatively narrow (weight‐average molecular weight/number‐average molecular weight < 1.2), supporting the living nature of the polymerization. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1016–1023, 2001     

Synthesis,characterization, and optimum reaction conditions of oligo‐2‐[(pyridine‐2‐yl‐methylene) amino] phenol

The reaction conditions of the oxidative polycondensation of 2‐[(pyridine‐2‐yl‐methylene) amino] phenol (2‐PMAP) with air O₂, H₂O₂, and NaOCl were studied in an aqueous alkaline medium between 60 and 90 °C. Oligo‐2‐[(pyridine‐2‐yl‐methylene) amino] phenol (O‐2‐PMAP) was characterized with ¹H NMR, Fourier transform infrared, ultraviolet–visible, size exclusion chromatography (SEC), and elemental analysis techniques. Moreover, solubility testing of the oligomer was performed in polar and nonpolar organic solvents. With the NaOCl, H₂O₂, and air O₂ oxidants, the conversions of 2‐PMAP into O‐2‐PMAP were 98, 87, and 62%, respectively, in an aqueous alkaline medium. According to SEC, the number‐average molecular weight, weight‐average molecular weight, and polydispersity index of O‐2‐PMAP were 2262 g mol^?1, 2809 g mol^?1, and 1.24 with NaOCl, 3045 g mol^?1, 3861 g mol^?1, and 1.27 with air O₂, and 1427 g mol^?1, 1648 g mol^?1, and 1.16 with air H₂O₂, respectively. Also, thermogravimetric analysis showed that O‐2‐PMAP was stable against thermooxidative decomposition. The weight loss of O‐2‐PMAP was 96.68% at 900 °C. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2717–2724, 2004     

Hyperbranched polyesters of 3,5‐diacetoxybenzoic acid: A reinvestigation

3,5‐Diacetoxybenzoic acid was polycondensed at temperatures in the range of 200–250 °C either in the absence of a catalyst or with addition of MgO or SnCl₂. The highest molecular weight was obtained in the absence of a catalyst. The matrix‐assisted laser desorption/ionization time‐of‐flight mass spectra revealed the formation of cyclic hyperbranched polyesters. The content of polyesters with cyclic core increased with higher conversions, and thus, with higher molecular weights. Furthermore, a loss of acetyl groups was found to be a significant side reaction. The same side reactions were found when trimethylsilyl 3,5‐bisacetoxybenzoate was polycondensed at 280 or 310 °C. Model reactions concerning the deacetylation mechanism were performed and the results are discussed. Size exclusion chromatography measurements in two different solvents proved that the high‐molecular‐weight fraction is not the result of aggregation via hydrogen bonds. Yet, the nature of the solvent, the profile of the columns, and the character of the detector had a significant influence on the shape of the elution curves and on the apparent molecular weights. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3751–3760, 2004     

Influence of tertiary diamines on the synthesis of high‐molecular‐weight poly(1,3‐cyclohexadiene)

The living synthesis of poly(1,3‐cyclohexadiene) was performed with an initiator adduct that was synthesized from a 1:2 (mol/mol) mixture of N,N,N′,N′‐tetramethylethylenediamine (TMEDA) and n‐butyllithium. This initiator, which was preformed at 65 °C, facilitated the synthesis of high‐molecular‐weight poly(1,3‐cyclohexadiene) (number‐average molecular weight = 50,000 g/mol) with a narrow molecular weight distribution (weight‐average molecular weight/number‐average molecular weight = 1.12). A plot of the kinetic chain length versus the time indicated that termination was minimized and chain transfer to the monomer was eliminated when a preformed initiator adduct was used. Chain transfer was determined to occur when the initiator was generated in situ. The polymerization was highly sensitive to both the temperature and the choice of tertiary diamine. The use of the bulky tertiary diamines sparteine and dipiperidinoethane resulted in poor polymerization control and reduced polymerization rates (7.0 × 10⁻⁵ s⁻¹) in comparison with TMEDA‐mediated polymerizations (1.5 × 10⁻⁴ s⁻¹). A series of poly(1,3‐cyclohexadiene‐block‐isoprene) diblock copolymers were synthesized to determine the molar crossover efficiency of the polymerization. Polymerizations performed at 25 °C exhibited improved molar crossover efficiencies (93%) versus polymerizations performed at 40 °C (80%). The improved crossover efficiency was attributed to the reduction of termination events at reduced polymerization temperatures. The microstructure of these polymers was determined with ¹H NMR spectroscopy, and the relationship between the molecular weight and glass‐transition temperature at an infinite molecular weight was determined for polymers containing 70% 1,2‐addition (150 °C) and 80% 1,4‐addition (138 °C). © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1216–1227, 2005     

Coupling selectivity in the radical‐controlled oxidative polymerization of 4‐phenoxyphenol catalyzed by (1,4,7‐triisopropyl‐1,4,7‐triazacyclononane)copper(II) complex

Various effects on the coupling selectivity of the oxidative polymerization of 4‐phenoxyphenol catalyzed by (1,4,7‐triisopropyl‐1,4,7‐triazacyclononane)copper(II) halogeno complex [Cu(tacn)X₂] are described. With respect to the amount of the catalyst and the nature of the halide ion (X) of Cu(tacn)X₂, the coupling selectivity hardly changed. The Cu(tacn) catalyst possessed a turnover number greater than 1860. As the temperature of the reaction and the polarity of the reaction solvent were elevated, the C O coupling at the o‐position increased, but the C C coupling was not involved. For the polymerization in toluene at 80 °C, poly(1,4‐phenylene oxide), obtained as a methanol‐insoluble part, showed the highest number‐average molecular weight of 4000 with a melting point (T_m) of 195 °C. Only a slight change in the coupling selectivity was observed in the presence or absence of hindered amines as the base. Surprisingly, however, the C O selectivity decreased from 100 to 24% with less hindered amines, indicating that the selectivity drastically changed from a preference for C O coupling to a preference for C C coupling. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4792–4804, 2000