Simultaneous determination of the styrene unit content and assessment of molecular weight of triblock copolymers in adhesives by a size exclusion chromatography method

The content of styrene units in nonhydrogenated and hydrogenated styrene‐butadiene‐styrene and styrene‐isoprene‐styrene triblock copolymers significantly influences product performance. A size exclusion chromatography method was developed to determine the average styrene content of triblock copolymers blended with tackifier in adhesives. A complete separation of the triblock copolymer from the other additives was realized with size exclusion chromatography. The peak area ratio of the UV and refraction index signals of the copolymers at the same effective elution volume was correlated to the average styrene unit content using nuclear magnetic resonance spectroscopy with commercial copolymers as standards. The obtained calibration curves showed good linearity for both the hydrogenated and nonhydrogenated styrene‐butadiene‐styrene and styrene‐isoprene‐styrene triblock copolymers (r  = 0.974 for styrene contents of 19.3–46.3% for nonhydrogenated ones and r  = 0.970 for the styrene contents of 23–58.2% for hydrogenated ones). For copolymer blends, the developed method provided more accurate average styrene unit contents than nuclear magnetic resonance spectroscopy provided. These results were validated using two known copolymer blends consisting of either styrene‐isoprene‐styrene or hydrogenated styrene‐butadiene‐styrene and a hydrocarbon tackifying resin as well as an unknown adhesive with styrene‐butadiene‐styrene and an aromatic tackifying resin. The methodology can be readily applied to styrene‐containing polymers in blends such as poly(acrylonitrile‐butadiene styrene).     

Effect of PEO‐PPO‐PEO copolymer on the mechanical and thermal properties and morphological behavior of biodegradable poly (L‐lactic acid) (PLLA) and poly (butylene succinate‐co‐L‐lactate) (PBSL) blends

A blend of two biodegradable and semi‐crystalline polymers, poly (L‐lactic acid) (PLLA; 70 wt%) and poly (butylene succinate‐co‐L‐lactate) (PBSL; 30 wt%), was prepared in the presence of various polyethylene oxide‐polypropylene oxide‐polyethylene oxide (PEO‐PPO‐PEO) triblock copolymer contents (0.5, 1, 2 wt%). Mechanical, thermal properties, and Fourier transform infrared (FTIR) analysis of the blends were investigated. It was found that the addition of copolymer to PLLA/PBSL improved the fracture toughness of the blends as shown by mode I fracture energies. It was supported by morphological analysis where the brittle deformation behavior of PLLA changed to ductile deformation with the presence of elongated fibril structure in the blend with copolymer system. The glass transition temperature (T_g), melting temperature (T_m) of PLLA, and PBSL shift‐closed together indicated that some compatibility exists in the blends. In short, PEO‐PPO‐PEO could be used as compatibilizer to improve the toughness and compatibility of the PLLA/PBSL blends. Copyright © 2010 John Wiley & Sons, Ltd.     

Stabilization of a cocontinuous phase morphology by a tapered diblock or triblock copolymer in polystyrene‐rich low‐density polyethylene/polystyrene blends

The stability against the thermal annealing of a cocontinuous two‐phase morphology developed in polystyrene (PS)/low‐density polyethylene (LDPE) blends containing 80 wt % PS was investigated. Blends containing 1, 5, and 10 wt % of a tapered diblock poly(styrene‐block‐hydrogenated butadiene) (P(S‐b‐hB)) or triblock poly(styrene‐block‐hydrogenated butadiene‐block‐styrene) (P(S‐hB‐S)) copolymer were melt‐blended with roll‐mill mixing equipment. The efficiency of each of the two copolymers in stabilizing against coalescence the cocontinuous morphology was examined. The tensile properties of the resulting blends, annealed and nonannealed, were also examined in relation to the morphology induced by thermal annealing. The phase morphology was studied by optical and scanning electron microscopy. With computer‐aided image analysis, it was possible to obtain a measurable characteristic parameter to quantify the cocontinuous phase morphology. When it was necessary, the extraction of one phase with a selective solvent was performed. Although the observed differences were subtle, the tapered diblock exhibited a more efficient compatibilizing activity than the triblock copolymer, particularly at a low concentration of about 2 wt %. The superiority of the tapered diblock over the triblock might be due to its ability to quantitatively locate at the LDPE/PS interface and consequently form a more efficient barrier against the subsequent breakup of the elongated structures of the cocontinuous phase morphology. The tensile properties of the triblock‐modified blends were more sensitive to thermal annealing than the tapered‐modified ones. This deficiency was ascribed to the phase morphology coarsening of the dispersed polyethylene phase. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 202–216, 2003     

Influence of Domain Size on Toughness of Poly(styrene‐block‐butadiene) Star Block Copolymer/Polystyrene Blends

Summary: The toughness of poly(styrene‐block‐butadiene) star block copolymer/polystyrene (PS) blends have been investigated using the essential‐work‐of‐fracture approach. The blends show a co‐continuous or layer‐like structure of polystyrene‐rich and polybutadiene‐rich domains arising from the used extrusion process. A tough‐to‐brittle transition at a critical domain size of polystyrene‐rich domains of about 50 nm and a maximum in the non‐essential work of fracture at 20–30% PS (co‐continuous morphology) have been found.

Non‐essential work of fracture as a function of the mean thickness of polystyrene‐rich domains, demonstrating a tough‐to‐brittle transition at a critical domain thickness about 50 nm. AFM micrograph of a star block copolymer/PS‐blend containing 40% PS.     

Synthesis of Maleated Ionomers via Ring‐Opening Reaction of Epoxidized (Styrene‐Butadiene‐Styrene) Triblock Copolymer with Potassium Hydrogen Maleate and Study of their Properties

A novel method for synthesizing maleated ionomer of (styrene‐butadiene‐styrene) triblock copolymer (SBS) from epoxidized SBS was developed. The epoxidized SBS was prepared via epoxidation of SBS with performic acid formed in situ by 30% H₂O₂ and formic acid in cyclohexane in the presence of polyethylene glycol 600 as a phase transfer catalyst. The maleated ionomer was obtained by a ring‐opening reaction of the epoxidized SBS solution with an aqueous solution of potassium hydrogen maleate. The optimum conditions for the ring‐opening reaction and some properties of the ionomers were studied. It is necessary to use phase transfer catalyst, ring‐opening catalyst and a pH regulator (dipotassium maleate) for obtaining the epoxy group conversion over 90%. The product was characterized by FTIR spectrophotometry and transmission electron microcroscopy (TEM) to be an ionomer with domains of maleate ionic groups. With increasing ionic groups, the water absorbency and the dilute solution viscosity of the ionomer increase, whereas the oil absorbency decreases. The tensile strength and ultimate elongation of ionomers increase with ionic group content and are higher than those of the original SBS without using any ionic plasticizer, which is usually used with the sulfonated ionomer. The ionomers with 1.2–1.7 mmol ionic groups/g exhibit optimum mechanical properties and behave as thermoplastic elastomers. The ionomer can be used as a compatibilizer for the blends of SBS with oil resistant chlorohydrin rubber (CHR). Addition of 3 wt% ionomer to the blend can increase the tensile strength and ultimate elongation of the blend optimally. The compatibility of the blends enhanced by adding the ionomer was shown by scanning electron microscopy (SEM). The blend of equal weight of SBS and CHR compatibilized by the ionomer behaves as a toluene resistant thermoplastic elastomer.     

The influence of partial emulsification on coalescence suppression and interfacial tension reduction in PP/PET blends

This study examines how the relative role of coalescence suppression and interfacial tension reduction influence the particle size at various levels of in situ compatibilization. The polymers studied are polyethylene terephthalate (PET) as matrix and a polypropylene (PP) as dispersed phase compatibilized by a triblock copolymer of poly(styrene–hydrogenated butadiene–styrene) (SEBS) grafted with maleic anhydride. The interfacial tension was studied by the breaking‐thread method, and it was used along with the morphology to characterize the emulsification efficacy of the copolymers. By modifying the concentration of MA grafted on the SEBS, different levels of emulsification of the blends were obtained. A comparison of 1/99 and 10/90 PP/PET blends compatibilized by SEBS‐g‐MA allows one to distinguish the relative role of interfacial tension and coalescence suppression in diminishing particle size. It is shown that varying degrees of residual coalescence remain, depending on the level of %MA in the copolymer. A detailed study of the 2%MA system below interfacial saturation was carried out to shed further light on the dependence of coalescence suppression on emulsification level and interfacial coverage. After separating out the contribution of interfacial tension on particle size reduction, it is shown that coalescence suppression for this system increases gradually with areal density of modifier at the interface right up to the region of interfacial saturation. Finally, the interfacial and morphological data were used to test the ability of the Lee and Park model to describe coalescence in polymer blends. Reasonable agreement was found between the parameter c₁, describing the coalescence in that model, and the trends related to residual coalescence from this study. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 939–951, 1999     

Filler‐polymer interactions of styrene and butadiene units in silica‐filled styrene–butadiene rubber compounds

Styrene–butadiene rubber (SBR) is a copolymer of styrene and butadiene, and the butadiene unit is composed of cis‐1,4‐, trans‐1,4‐, and 1,2‐components. Filler‐polymer interactions of each component of SBR in silica‐filled SBR compounds were examined by microstructure analysis of the bound and unbound rubbers. The composition ratio of butadiene and styrene units (butadiene/styrene) of the bound rubber was higher than that of the compounded rubber. Of the butadiene units, the 1,2‐component of the bound rubber was more abundant than the cis‐1,4‐ and trans‐1,4‐components. The filler‐polymer interaction of the butadiene unit with silica was stronger than that of the styrene unit, and the interaction of the 1,2‐component was stronger as compared with the others. The butadiene–styrene ratio of the bound rubber of the compounds containing the silane coupling agent was lower than for the compounds without the silane. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 577–584, 2004     

Epoxies toughened with triblock copolymers

Three different commercial triblock copolymers from Arkema were evaluated as potential toughening agents for two different lightly crosslinked epoxies. It was found that the plane strain fracture toughness, K_IC, was on the order of 3.0 MPa√m for 10 parts per hundred resin (phr) of NanoStrength™ E20 resin (a styrene–butadiene–methylacrylate, SBM, type triblock copolymer) in epoxies cured with either aminoethylpiperazine or piperidine. In contrast, 10 phr NanoStrength E40 resin (also an SBM type triblock copolymer) was ineffective in toughening such epoxies. The difference in toughening effectiveness was attributed to the smaller amount of polybutadiene present in the E40 resin. The third toughening agent from Arkema was NanoStrength M22 resin, which is a symmetric triblock copolymer consisting of side blocks of PMMA surrounding a center block of poly(butyl acrylate) and is designated as MAM. At 10 phr MAM both lightly crosslinked epoxies exhibited improvements in toughness. Morphologies were characterized using TEM and toughening mechanisms revealed using SEM and TOM. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1470–1481, 2007     

Structure and mechanical properties of talc‐filled blends of polypropylene and styrenic block copolymers

The structure–property relationships of isotactic polypropylene (iPP)/styrenic block copolymer blends filled with talc were examined by optical and scanning electron microscopy, wide‐angle X‐ray diffraction, and tensile‐ and impact strength measurements. The composites were analyzed as a function of the poly(styrene‐b‐ethylene‐co‐propylene) diblock copolymer (SEP) and the poly(styrene‐b‐butadiene‐b‐styrene) triblock copolymer (SBS) content in the range from 0 to 20 vol % as elastomeric components and with 12 vol % of aminosilane surface‐treated talc as a filler. Talc crystals incorporated in the iPP matrix accommodated mostly plane‐parallel to the surface of the samples and strongly affected the crystallization process of the iPP matrix. The SBS block copolymer disoriented plane‐parallel talc crystals more significantly than the SEP block copolymer. The mechanical properties depended on the final phase morphology of the investigated iPP blends and composites and supermolecular structure of the iPP matrix because of the interactivity between their components. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1255–1264, 2004     

Compatibilization level effects on the structure and mechanical properties of rubber‐modified polyamide‐6/clay nanocomposites

Exfoliated polyamide‐6 (PA6)/organically modified montmorillonite clay (OMMT) nanocomposites (PNs) were modified with partially maleinized styrene–ethylene/butadiene–styrene triblock copolymers (SEBS) at three maleinization levels in an attempt to link in these materials high toughness with appropriate small‐strain and fracture tensile properties. OMMT stayed only in the PA6 matrix, and no preferential location in the matrix/rubber interphase was observed. The increased dispersed phase size upon the addition of OMMT was attributed to interactions between maleic anhydride (MA) functionalized SEBS and the surfactant of OMMT. The rubber particle size generally decreased when the MA content of SEBS increased, and this indicated compatibilization. The subsequent good adhesion led to tough nanocomposites across a wide range of both strain rates and fracture modes. As the critical interparticle distance (τ_c) decreased with the MA content, and the other parameters that could influence the surface‐to‐surface mean interparticle distance did not change, it is proposed that in these PNs higher adhesion leads to a smaller τ_c value. Finally, the presence in the matrix of a nanostructured clay makes the rubber content necessary for the toughness jump to increase and τ_c to decrease. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3611–3620, 2005     

Use of maleic anhydride compatibilization to improve toughness and other properties of polylactide blended with thermoplastic elastomers

Polylactide (PLA) being a very brittle biopolymer could be toughened by blending with thermoplastic elastomers such as thermoplastic polyurethane elastomer (TPU) and thermoplastic polyester elastomer (TPE); unfortunately, these blends are immiscible forming round domains in the PLA matrix. Therefore, the purpose of this study was to investigate the effects of using maleic anhydride (MA) compatibilization on the toughness and other properties of PLA blended with TPU and TPE. MA grafting on the PLA backbone (PLA‐g‐MA) was prepared separately by reactive extrusion and added during melt blending of PLA/thermoplastic elastomers. IR spectroscopy revealed that MA graft might interact with the functional groups present in the hard segments of TPU and TPE domains via primary chemical reactions, so that higher level of compatibilization could be obtained. SEM studies indicated that PLA‐g‐MA compatibilization also decreased the size of elastomeric domains leading to higher level of surface area for more interfacial interactions. Toughness tests revealed that Charpy impact toughness and fracture toughness (K_IC and G_IC) of inherently brittle PLA increased enormously when the blends were compatibilized with PLA‐g‐MA. For instance, G_IC fracture toughness of PLA increased as much as 166%. It was also observed that PLA‐g‐MA compatibilization resulted in no detrimental effects on the other mechanical and thermal properties of PLA blends. Copyright © 2014 John Wiley & Sons, Ltd.     

Upper critical solution temperature type phase behavior of poly(styrene‐co‐acrylonitrile) blends with poly(styrene‐co‐n‐phenyl maleimide) and their interaction energies

To enhance the heat resistance of poly(styrene‐co‐acrylonitrile‐co‐butadiene), ABS, miscibility of poly(styrene‐co‐acrylonitrile), SAN, with poly(styrene‐co‐n‐phenyl maleimide), SNPMI, having a higher glass transition temperature than SAN was explored. SAN/SNPMI blends casted from solvent were immiscible regardless of copolymer compositions. However, SNPMI copolymer forms homogeneous mixtures with SAN copolymer within specific ranges of copolymer composition upon heating caused by upper critical solution temperature, UCST, type phase behavior. Since immiscibility of solvent casting samples can be driven by solvent effects even though SAN/SNPMI blends are miscible, UCST‐type phase behavior was confirmed by exploring phase reversibility. When copolymer composition of SNPMI was fixed, the phase homogenization temperature of SAN/SNPMI blends was increased as AN content in SAN copolymer increased. To understand the observed phase behavior of SAN/SNPMI blend, interaction energies of blends were calculated from the UCST‐type phase boundaries by using the lattice‐fluid theory combined with a binary interaction model. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1131–1139, 2008     

Microphase‐separated structure of 1,3‐cyclohexadiene/butadiene triblock copolymers and its effect on mechanical and thermal properties

We report the effect of microphase‐separated structure on the mechanical and thermal properties of several poly(1,3‐cyclohexadiene‐block‐butadiene‐block‐1,3‐cyclohexadiene) triblock copolymers (PCHD‐block‐PBd‐block‐PCHD) and of their hydrogenated derivatives: poly(cyclohexene‐block‐ethylene/butylene‐block‐cyclohexene) triblock copolymers (PCHE‐block‐PEB‐block‐PCHE). Both mechanical strength and heat‐resistant temperature (ex. Vicat Softening Temperature: VSPT) tended to increase with an increase in the 1,3‐cyclohexadiene (CHD)/butadiene ratio. On the other hand, heat resistance of the hydrogenated block copolymer was found to be higher than that of the unhydrogenated block copolymer. However, the mechanical strength was lower than those of the unhydrogenated block copolymer with the same ratio of CHD to butadiene. To clarify the relationship between the higher order structures of those block copolymers and their properties, we observed the microphase‐separated structure by transmission electron microscope (TEM). Hydrogenated block copolymers were found to have more finely dispersed microphase‐separated structures than those of the unhydrogenated block copolymers with the same CHD/Bd ratios through the use of TEM and the small‐angle X‐ray scattering (SAXS) technique. Those results indicated that the segregation strength between the PCHE block sequence and the PEB block sequence increased, depending on hydrogenation of the unhydrogenated precursor. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 13–22, 2001     

Effect of preparation method on nanoscopic structure of conductive SBS/PANI blends: Study using small‐angle X‐ray scattering

Small‐angle X‐ray scattering (SAXS) studies of electrically conductive blends based on polyaniline–dodecylbenzenesulfonic acid (PANI–DBSA)/styrene–butadiene–styrene (SBS) triblock copolymer were performed to investigate the influence of the blend preparation procedure on the nanoscopic structure of the blends. The blends were prepared by mechanical mixing (MM) procedure and by in situ polymerization (ISP) of aniline in the presence of SBS. The results indicate that pure PANI–DBSA presents an extended phase consisting of crystalline islands of nanometric size, with a good spatial correlation between them, embedded into an amorphous PANI phase. This feature was not observed in SBS/PANI–DBSA blends prepared by MM or ISP. In MM blends, the PANI phase is constituted by smaller domains, containing poorly spatially correlated crystalline islands, whereas in ISP blends with low or medium amount of PANI, there is no SAXS peak which could be related to a spatial correlation between PANI crystalline islands. The conductivity of the ISP blends is higher when compared to MM blends because of the higher homogeneity at nanometric scale. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3069–3077, 2007     

Hydrocarbon polymers containing six-membered rings in the main chain. Microstructure and properties of poly(1,3-cyclohexadiene)

The relationship between the microstructure and the properties of poly(1,3-cyclohexadiene)s, obtained by living anionic polymerization with an alkyllithium/amine system, and their hydrogenated derivatives are reported. The 1,2-bond/1,4-bond molar ratio of poly(1,3-cyclohexadiene) was determined by measuring 2D-NMR with the H H COSY method. The glass transition temperature of poly(1,3-cyclohexadiene) was found to rise with an increase in the ratio of 1,2-bonds to 1,4-bonds or with an increase of the number average molecular weight. The 1,2-bond of the polymer chain gives a high flexural strength and heat distortion temperature. Hydrogenated poly(1,3-cyclohexadiene) has the highest T_g (231°C) among all hydrocarbon polymers ever reported. 1,3-Cyclohexadiene–butadiene–1,3-cyclohexadiene triblock copolymer and 1,3-cyclohexadiene–styrene–1,3-cyclohexadiene triblock copolymer have high heat resistance and high mechanical strength. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1657–1668, 1998     

Effect of reactive compatibilization on the properties of poly(butylene terephthalate)/acrylonitrile–ethylene–propylene–diene–styrene blends

Blends of poly(butylene terephthalate) (PBT) with 30 wt % acrylonitrile–ethylene–propylene–diene–styrene (AES) were prepared with methyl methacrylate (MMA)/glycidyl methacrylate (GMA)/ethyl acrylate (EA) terpolymers (MGEs) as compatibilizing agents. These acrylic terpolymers were miscible with the styrene–acrylonitrile (SAN) phase of AES, whereas the epoxide groups of GMA could react with the PBT end groups; this could lead to the formation of grafted copolymers (PBT‐g‐MGE) at the PBT/AES interface during the melt processing of the blends if at least a fraction of this interface was formed between the PBT and SAN phases. This study found evidence of the aforementioned interfacial structure through the effectiveness of the MGE terpolymers in promoting the compatibilization, as evaluated by dynamical mechanical analysis, through the increase in the viscosity of the blends, and through the reduction of the AES particle size dispersed in the PBT matrix. These effects became more intense with an increase in the overall concentration of GMA in the blends and with a reduction of the molecular weight of MGE. Another effect promoted by the compatibilization was a remarkable reduction of the brittle–ductile transition temperatures of the blends, which was correlated with the reduction of the AES particle size. However, this correlation between the brittle–ductile transition temperatures and particle size did not hold for the blend with the lowest AES particle size, which showed a high ductile–brittle transition temperature. These mechanical behaviors were examined on the basis of the current theory of the toughening of thermoplastics, which takes into account the importance of the rubber interparticle distance and the cavitation process of these particles. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1244–1259, 2005     

Polypropylene/montmorillonite nanocomposites toughened with SEBS‐g‐MA: Structure–property relationship

Polypropylene (PP)/organo‐montmorillonite (Org‐MMT) nanocomposites toughened with maleated styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MA) were prepared via melt compounding. The structure, mechanical properties, and dynamic mechanical properties of PP/SEBS‐g‐MA blends and their nanocomposites were investigated by X‐ray diffraction (XRD), polarizing optical microscopy (POM), tensile, and impact tests. XRD traces showed that Org‐MMT promoted the formation of β‐phase PP. The degree of crystallinity of PP/SEBS‐g‐MA blends and their nanocomposites were determined from the wide angle X‐ray diffraction via profile fitting method. POM experiments revealed that Org‐MMT particles served as nucleating sites, resulting in a decrease of the spherulite size. The essential work of fracture approach was used to evaluate the tensile fracture toughness of the nanocomposites toughened with elastomer. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3112–3126, 2005     

Hydrogenation of Styrene‐Butadiene Rubber Catalyzed by Ru(CHCHPh)Cl(CO)(PCy3)2

Summary: The hydrogenation of a copolymer of styrene and butadiene (SBR) catalyzed by Ru(CHCHPh)Cl(CO)(PCy₃)₂ was experimentally investigated within the temperature range of 120–160 °C, at Pequation/tex2gif-inf-7.gif of 300–1 200 psi, and a catalyst concentration of 10–78 × 10⁻⁶ M . Special attention was paid to minimizing the catalyst metal residue and crosslinking in the product. The results indicated that high‐quality hydrogenated SBR was achieved without crosslinking and the metal residue was less than 7 ppm without a post‐treatment.

IR spectra of the styrene–butadiene rubber before (a) and after (b) hydrogenation with the Ru(CHCHPh)Cl(CO)(PCy₃)₂ catalyst were observed as reported here. The disappearance of all characteristic absorbencies of CC (724, 910, 967, and 994 cm⁻¹) suggests nearly quantitative hydrogenation of the CC bonds.     

Brittle–ductile transition of polypropylene/ethylene–propylene–diene monomer blends induced by size,temperature, and time

To study the brittle–ductile transition (BDT) of polypropylene (PP)/ethylene–propylene–diene monomer (EPDM) blends induced by size, temperature, and time, the toughness of the PP/EPDM blends was investigated over wide ranges of EPDM content, temperature, and strain rate. The toughness of the blends was determined from the tensile fracture energy of the side‐edge notched samples. The concept of interparticle distance (ID) was introduced into this study to probe the size effect on the BDT of PP/EPDM blends, whereas the effect of time corresponded to that of strain rate. The BDT induced by size, temperature, and time was observed in the fracture energy versus ID, temperature, and strain rate. The critical BDT temperatures for various EPDM contents at different initial strain rates were obtained from these transitions. The critical interparticle distance (ID_c) increased nonlinearly with increasing temperature, and when the initial strain rate was lower, the ID_c was larger. Moreover, the variation of the reciprocal of the initial strain rate with the reciprocal of temperature followed different straight lines for various EPDM contents. These straight lines were with the same slope. Furthermore, a diagram at critical BDT points in three dimensions (ID, T, and initial strain rate) was given for the PP/EPDM blends. The brittle and ductile zones are clearly shown in this diagram. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1433–1440, 2004     

聚合物共混物脆韧转变性能研究 Ⅳ橡胶粒子的分布对PVC/NBR共混物脆韧转变的影响

根据作者已建立的准网络形态模型和推导出的基体层厚度计算公式，从实验上研究了橡胶粒子的分布对聚氯乙烯（ＰＶＣ）／丁氰橡胶（ＮＢＲ）共混物脆韧转变的影响．结果表明，不仅无规形态ＰＶＣ／ＮＢＲ共混物存在脆韧转变主曲线，而且准网络形态ＰＶＣ／ＮＢＲ共混物也存在脆韧转变主曲线．但是两条主曲线明显不重合，表明橡胶粒子的分布对ＰＶＣ／ＮＢＲ共混物脆韧转变有显著影响．而且准网络形态ＰＶＣ／ＮＢＲ共混物的临界基体层厚度比无规形态ＰＶＣ／ＮＢＲ共混物的临界基体层厚度大得多，表明准网络形态比无规形态明显有利于增韧．因此临界基体层厚度不仅是基体的特征参数，还是界面粘结和橡胶粒子分布的函数．