Preparation and properties of biocomposites composed of bio‐based epoxy resin,tannic acid,and microfibrillated cellulose

As new bio‐based epoxy resin systems, glycerol polyglycidyl ether (GPE) and sorbitol polyglycidyl ether (SPE) were cured with tannic acid (TA) at various conditions. When the curing conditions were optimized for the improvement of thermal and mechanical properties, the most balanced properties were obtained for the GPE/TA and SPE/TA cured at 160 °C for 2–3 h at the epoxy/hydroxyl ratio of 1/1. The cured SPE/TA had a higher glass transition temperature (T_g) and tensile strength than the cured GPE/TA. Next, biocomposites of GPE/TA and SPE/TA with microfibrillated cellulose (MFC) were prepared by mixing aqueous solution of the epoxy/curing reagent with MFC, and subsequent drying and curing at the optimized condition. For both the GPE/TA/MFC and SPE/TA/MFC biocomposites, T_g and the storage modulus at rubbery plateau region increased with increasing MFC content over the studied range of 3–15 wt %. The tensile strength at 25 °C for GPE/TA/MFC biocomposite with MFC content 10 wt % was 76% higher than that of control GPE/TA, while the tensile modulus was little improved. On the other hand, the tensile strength and modulus of SPE/TA/MFC biocomposite with MFC content 10 wt % were 30 and 55% higher than those of control SPE/TA, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 425–433, 2010     

Amine‐cured epoxy/clay nanocomposites. I. Processing and chemical characterization

The processing of nanocomposite materials composed of amine‐cured diglycidyl ether of bisphenol A (DGEBA) reinforced with organomontmorillonite clay is reported. A novel sample preparation scheme was used to process the modified clay in the glassy epoxy network, resulting in nanocomposites where the clay was both exfoliated and intercalated by the epoxy network. The processing scheme involves sonication of the constituent materials in a solvent, followed by solvent extraction to generate a composite with homogeneous dispersions of the nanoclay. Fourier transform infrared spectroscopy (FTIR) and Fourier transform (FT‐)Raman spectroscopy confirmed that the chemical structure of the epoxy network was not affected by the use of solvents in this processing scheme. The glass‐transition temperature, T_g, linearly increased with an increased weight ratio of the nanoclay. The microstructure of clay nanoplatelets in the composites was observed with transmission electron microscopy (TEM), wide‐angle X‐ray scattering (WAXS), and small‐angle X‐ray scattering (SAXS). It was found that the clay nanoplatelets were well‐dispersed, and were intercalated as well as exfoliated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4384–4390, 2004     

Exploitation of introducing of catalytic centers into layer galleries of layered silicates and related epoxy nanocomposites. I. Epoxy nanocomposites derived from montmorillonite modified with catalytic surfactant‐bearing carboxyl groups

Montmorillonite (MMT) was modified with the acidified cocamidopropyl betaine (CAB) and the resulting organo‐montmorillonite (O‐MMT) was dispersed in an epoxy/methyl tetrahydrophthalic anhydride system to form epoxy nanocomposites. The intercalation and exfoliation behavior of the epoxy nanocomposites were examined by X‐ray diffraction and transmission electron microscopy. The curing behavior and thermal property were investigated by in situ Fourier transform infrared spectroscopy and DSC, respectively. The results showed that MMT could be highly intercalated by acidified CAB, and O‐MMT could be easily dispersed in epoxy resin to form intercalated/exfoliated epoxy nanocomposites. When the O‐MMT loading was lower than 8 phr (relative to 100 phr resin), exfoliated nanocomposites were achieved. The glass‐transition temperatures (T_g's) of the exfoliated nanocomposite were 20 °C higher than that of the neat resin. At higher O‐MMT loading, partial exfoliation was achieved, and those samples possessed moderately higher T_g's as compared with the neat resin. O‐MMT showed an obviously catalytic nature toward the curing of epoxy resin. The curing rate of the epoxy compound increased with O‐MMT loading. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1192–1198, 2004     

Molecular composites made of ionic poly(p‐phenylene terephthalamide) and poly(4‐vinylpyridine): Relaxation behavior

Molecular composites were prepared from several types of ionically modified, poly(p‐phenylene terephthalamide) (PPTA) dispersed in a poly(4‐vinylpyridine) matrix. Optical clarity tests indicated that the component polymers of the composite were miscible, at least at low concentrations of the rodlike reinforcement. In composites containing ionic PPTA, where ionic sulfonate groups were attached as side groups either to PPTA chains or to PPTA anion chains, the glass‐transition temperature (T_g) was increased by l0 °C or more, at 5 wt % reinforcement. At concentrations of 10–15 wt % of the ionic polymer, T_g values leveled off or decreased slightly. This suggested that some aggregation of the rigid‐rod molecules occurred. In composites containing ionic PPTA, where the ionic sulfonate groups were directly attached to the phenylene rings of PPTA chains, not only was T_g shifted significantly to higher temperatures, but the rubbery plateau modulus retained high values up to temperatures of 250 °C or above. Observed effects were considered to be the result of strong ionic interactions between the ionic reinforcement polymer and the polar matrix polymer. The possible effects of the counterion on T_g and the storage modulus are discussed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1110–1117, 2002     

The POSS side chain epoxy nanocomposite: Synthesis and thermal properties

The IPI‐POSS‐modified epoxy resin (IPEP) was prepared from isocyanato‐propyldinethylsilyl‐isobutyl‐POSS (IPI‐POSS) and diglycidyl ether of bisphenol A epoxy resin. The steric hindrance of the IPEP bulky POSS side chain improved the curing activation energies. The POSS particles sizes were about 2–3 nm and dispersed uniformly. At lower IPEP concentration (POSS < 12 wt %), the glass transition temperatures (T_gs) of the IPEP nanocomposites increased from 118 to 170 °C. The char yield increased from 15 to 20 wt %, and the LOI values increased from 22 to 28. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 643–652, 2010     

Glass‐transition temperature behavior of alumina/PMMA nanocomposites

Alumina/poly(methyl methacrylate) (PMMA) nanocomposites were synthesized by an in situ free‐radical polymerization process with 38 and 17 nm diameter γ‐alumina nanoparticles. At extremely low filler weight fractions (<1.0 wt % of 38 nm fillers or < 0.5 wt % of 17 nm fillers) the glass‐transition temperature (T_g) of the nanocomposites drops by 25 °C when compared to the neat polymer. Further additions of filler (up to 10 wt %) do not lead to additional T_g reductions. The thermal behavior is shown to vary with particle size, but this dependence can be normalized with respect to a specific surface area. The nanocomposite T_g phenomenon is hypothesized to be because of nonadhering nanoparticles that serve as templates for a porous system with many internal interfaces that break up the percolating structure of dynamically heterogeneous domains recently suggested by Long, D.; and Lequeux, F. Eur Phys J E 2001, 4, 371 to be responsible for the T_g reductions in polymer ultrathin films. The results also point to a far field effect of the nanoparticle surface on the bulk matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4371–4383, 2004     

Influence of interaction between poly(methyl methacrylate) and clay on the properties of nanocomposites prepared by a heterocoagulation method

To have a better insight into the effect of interaction between polymer matrix and clay on the properties of nanocomposite, poly(methyl methacrylate)/clay nanocomposites were prepared by a heterocoagulation method. Using a reactive cationic emulsifier, methacryloyloxyethyltrimethyl ammonium chloride (METAC), a strong polymer–clay interaction was obtained with the advantage of keeping a consistent polymer matrix property. X‐ray diffraction and transmission electronic microscopy indicated an exfoliated structure in nanocomposites. The glass transition temperature (T_g) of the nanocomposites was measured by DSC and DMA. The DMA results showed that with a strong interaction, PMMA–METAC nanocomposite showed a 20 °C enhancement in glass transition temperature (T_g), whereas a slight increase in T_g was observed for PMMA–cetyl trimethylammonium bromide (CTAB)/clay nanocomposite with a weak interaction. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 733–738, 2010     

Molecular motion,morphology, and thermal properties of multiwall carbon nanotube/polysilsesquioxane composite

Diglycidyl ether of bisphenol A (DGEBA)‐bridged polyorganosiloxane precursors have been prepared successfully by reacting diglycidyl ether of bisphenol A epoxy resin with 3‐aminopropyltriethoxysilane. Acid‐modified and unmodified multiwalled carbon nanotube (MWCNT) were dispersed in the diglycidyl ether of bisphenol A‐bridged polyorganosiloxane precursors and cured to prepare the carbon nanotube/diglycidyl ether of bisphenol A‐bridged polysilsesquioxane (MWCNT/DGEBA‐PSSQ) composites. The molecular motion of MWCNT/DGEBA‐PSSQ nanocomposites was studied by high‐resolution solid‐state ¹³C NMR. Acid‐modification can improve the affinity between MWCNT and the polymer matrix. The molecular motion of the DGEBA‐PSSQ decreased with acid‐modified MWCNT content. However, when unmodified MWCNT was used, the molecular motion of the DGEBA‐PSSQ was increased. SEM and TEM microphotographs confirm that acid‐modified MWCNT exhibits better dispersion than unmodified MWCNT in DGBEA‐PSSQ. The dynamic mechanical properties of acid‐modified MWCNT/DGBEA‐PSSQ composites are more favorable than those of unmodified MWCNT. T_g of the DGEBA‐PSSQ decreased from 174.0 °C (neat DGEBA‐PSSQ) to 159.0 °C (1 wt % unmodified MWCNT) and 156.0 °C (1 wt % acid‐modified MWCNT). The storage modulus (at 30 °C) of the DGEBA‐PSSQ increased from 1.23 × 10⁹ Pa (neat DGEBA‐PSSQ) to 1.65 × 10⁹ Pa (1 wt % acid‐modified MWCNT). However, when unmodified MWCNT was used, the storage modulus of the DGEBA‐PSSQ decreased to 6.88 × 10⁸ Pa (1 wt % unmodified MWCNT). At high temperature, above 150 °C, storage modulus of nanocomposites was higher than that of neat polymer system. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 472–482, 2008     

Morphological and thermal properties of ABS/montmorillonite nanocomposites using two different ABS polymers and four different montmorillonite clays

ABS/Clay nanocomposites were prepared using two ABS with different Acrylonitrile (AN) contents and four montmorillonite clays; a natural clay (CNa+) and three modified clays, Cloisites 10A, 20A, and 30B. The composites were prepared in a twin‐screw extruder. Results were analyzed considering the effect of clay and ABS type, on the clay dispersion, intercalation and exfoliation, as well as on the storage modulus and thermal stability of the nanocomposites. XRD and TEM confirm that when using an ABS with higher AN content (ABS2), a better dispersion and intercalation–exfoliation can be obtained. Cloisites 20A and 30B, respectively the one with greater initial intergallery spacing, but lower polarity and with smaller inter‐gallery spacing but greater polarity, produce the ABS nanocomposites with the greater intergallery spacing. Both ABS polymers have similar storage modulus and T_g and in both cases, the modulus increases with the 4 wt % clay. This increase is greater with the modified clays and slightly greater with the ABS2. T_g, from tan δ, increases very little with the 4 wt % clay, but again, this is slightly greater with ABS2. TGA and flammability tests show that the dispersed clay enhances the thermal stability and that the ABS with higher AN content produces a greater increase in fire retardancy. Tests also show that the better thermal stability and fire retardancy is obtained with the Cloisites 20A or 30B. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 190–200, 2008     

Covalent bonded polymer–graphene nanocomposites

This report describes a new route to covalently bonded polymer–graphene nanocomposites and the subsequent enhancement in thermal and mechanical properties of the resultant nanocomposites. At first, the graphite is oxidized by the modified Hummers method followed by functionalization with Octadecylamine (ODA). The ODA functionalized graphite oxides are reacted with methacryloyl chloride to incorporate polymerizable ? C?C? functionality at the nanographene platelet surfaces, which were subsequently employed in in situ polymerization of methylmethacrylate to obtain covalently bonded poly(methyl methacrylate) (PMMA)–graphene nanocomposites. The obtained nanocomposites show significant enhancement in thermal and mechanical properties compared with neat PMMA. Thus, even with 0.5 wt % graphene nanosheets, the T_g increased from 119 °C for neat PMMA to 131 °C for PMMA–graphene nanocomposite, and the respective storage modulus increased from 1.29 to 2 GPa. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4262–4267, 2010     

Effect of moisture on the dynamic mechanical relaxation of polyamide-6/clay nanocomposites

This article investigates the effect of moisture on the dynamic mechanical behavior of polyamide-6 (PA6)/clay nanocomposites with dynamic mechanical analysis from −130 to 110 °C. The storage moduli increase with the clay loading for dried and moisture-absorbed samples because of the enhancing effect from the high-aspect-ratio nanoclay. Storage moduli for moisture-exposed samples are lower than those for dried samples; the longer the moisture absorption period is, the lower the moduli are for neat PA6 and PA6/clay nanocomposites. At temperatures below about 10 °C, however, samples exposed to moisture for longer periods tend to be stiffer than dried samples, probably because of the stiffening effect of ice. The peak temperature of the β relaxation shifts from −53 to −65 °C as the moisture content increases. The glass-transition temperature (T_g) or α relaxation dramatically shifts; its position is significantly lowered from 62 to 17 °C as the moisture content increases (longer moisture absorption period) and from 62 to 50 °C as the clay loading increases. The observed depression of the storage modulus and T_g may be attributed to the plasticization effect of moisture absorption. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1823–1830, 2004     

Viscoelastic characteristics of plasticized cellulose nanocomposites

The plasticization effects of cellulose diacetate composite systems including nanoparticles (montmorillonite, MMT) and plasticizers(diethyl phthalate, DEP) were investigated by the time–temperature superposition technique and viscoelastic modeling. Exhibiting the highest modulus value in the glass state, the viscoelastic modulus of the MMT nanocomposite rapidly decreased above the glass‐transition temperature (T_g). The Arrhenius‐type activation energy of pristine cellulose acetate showed the lowest value of activation energy and both DEP‐plasticized and MMT‐reinforced systems exhibited increased values of activation energy. Although the free volume fraction at the T_g decreased with the plasticizer content, it increased with the incorporation of MMT, seemingly preventing the polymer chains from being arranged in an ordered structure. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 59–65, 2005     

Synergism and multiple mechanical relaxations observed in ternary systems based on benzoxazine,epoxy, and phenolic resins

The synergism in the glass‐transition temperature (T_g) of ternary systems based on benzoxazine (B), epoxy (E), and phenolic (P) resins is reported. The systems show the maximum T_g up to about 180 °C in BEP541 (B/E/P = 5/4/1). Adding a small fraction of phenolic resin enhances the crosslink density and, therefore, the T_g in the copolymers of benzoxazine and epoxy resins. To obtain the ultimate T_g in the ternary systems, 6–10 wt % phenolic resin is needed. The molecular rigidity from benzoxazine and the improved crosslink density from epoxy contribute to the synergistic behavior. The mechanical relaxation spectra of the fully cured ternary systems in a temperature range of −140 to 350 °C show four types of relaxation transitions: γ transition at −80 to −60 °C, β transition at 60–80 °C, α₁ transition at 135–190 °C, and α₂ transition at 290–300 °C. The partially cured specimens show an additional loss peak that is frequency‐independent as a result of the further curing process of the materials. The ternary systems have a potential use as electronic packaging molding compounds as well as other highly filled systems. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1687–1698, 2000     

Rheological properties of ferrite nanocomposites based on nylon‐66

Effects of ferrite nanoparticles (0.1–20 wt %) on the rheological and other physical properties of nylon‐66 were investigated. The presence of ferrite nanoparticles less than 1 wt % increased the crystallization temperature (T_c) by 4.2 °C with ferrite content, but further addition decreased T_c. The onset temperature of degradation was increased by 7.3 °C at only 0.1 wt % loading of ferrite, after which the thermal stability of nylon‐66 was decreased with ferrite content. The incorporation of ferrite nanoparticles more than 5 wt % increased the dynamic viscosity (η′) with the loading level. Further, it produced notably shear thickening behavior in the low frequency, after which high degree of shear thinning was followed with ferrite content. In the Cole–Cole plot, the nanocomposites with ferrite lower than 5 wt % presented a single master curve, while further addition gave rise to a deviation from the curve. The relaxation time (λ) was increased with ferrite content and the difference of λ between nylon‐66 and its nanocomposite was greater at lower frequency. The tensile strength was a little increased up to 1 wt % loading, after which it was decreased with increasing the loading level. In addition, the introduction of the nanoparticles increased tensile modulus and decreased the ductility with ferrite content. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 371–377, 2006     

Enhanced interfacial interaction by grafting carboxylated‐macromolecular chains on nanodiamond surfaces for epoxy‐based thermosets

A novel core‐shell‐structured carboxylated‐styrene butadiene rubber (XSBR)‐functionalized nanodiamond (ND‐XSBR) was synthesized and characterized. Epoxy (EP) nanocomposites toughened by pristine ND and ND‐XSBR were investigated and compared. The ND‐XSBR‐reinforced nanocomposite exhibited mechanical properties superior to those of the one filled by pristine ND. At a low‐filler loading, the ND‐XSBR exhibited an impressive toughening effect. The maximum flexural strength was shown when the filler loading was as low as 0.1 wt % for the EP/ND‐XSBR nanocomposite. Furthermore, enhanced fracture toughness and fracture energy were shown by surface functionalization, representing enhanced compatibility between the ND‐XSBR and EP matrix. The glass transition temperature (T_g) and storage modulus of the nanocomposites were studied, and the EP/ND‐XSBR0.1 nanocomposite exhibited the highest T_g owing to the stronger interfacial interaction. The EP/ND‐XSBR0.2 exhibited higher storage modulus and T_g than the EP/ND0.2, because the higher interfacial interaction can restrict the molecular mobility of the EP by the functionalized ND‐XSBR. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1890–1898     

Extraordinary mechanical behavior of exfoliated montmorillonite/polymer nanocomposite films cast from soap‐free emulsion polymerized latices

The exfoliated montmorillonite (MMT) nanoplatelets tended to re‐stack with each other after casting the MMT/poly(methylacrylate‐co‐methylmethacrylate) P(MA‐co‐MMA) latex solutions fabricated by soap‐free emulsion polymerization into films as revealed by X‐ray diffraction and transmission electron microscopy. As the content of MMT was increased from 0 to 20 wt %, the T_g measured by differential scanning calorimetry was slightly decreased from 19.2 to 17.2 °C, whereas that measured by dynamic mechanical analysis was increased from 22 to 32 °C, indicating that the local motion of polymer segments has been retarded by MMT nanoplatelets. Besides, the elongated elliptical voids appeared during stretching of 1 wt % MMT/P(MA‐co‐MMA) film to cracking also illustrated the pinning effect provided by the exfoliated MMT. As the content of MMT was increased more than 10 wt %, the mechanical behavior of MMT/P(MA‐co‐MMA) nanocomposite films was changed from ductile to brittle nature with significant increase of Young's modulus and tensile strength owing to the restacking of exfoliated MMT nanoplatelets. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1064–1069, 2010     

Structure‐property relationships in exfoliated polyisoprene/clay nanocomposites

Structure‐property relationships in exfoliated polyisoprene (PI)/clay nanocomposites have been studied as a function of the clay concentration with rheometry, X‐ray diffraction, small‐angle X‐ray scattering, and transmission electron microscopy. The results presented here indicate that the interlayer spacing of layered silicates increases from 2 to at least approximately 14 nm because of the penetration of polymer molecules into the spacing between the silicate layers. The average aspect ratio (width/thickness) of the dispersed nanoplates is also estimated to be at least approximately 80. Additionally, the storage modulus of the nanocomposite exhibits frequency‐independent pseudo‐solidlike behavior above the percolation threshold [volume fraction of clay at the percolation threshold (?_p) = 0.02] and shows large enhancements (up to approximately six orders of magnitude) in comparison with the storage modulus of PI when the volume fraction of clay (?) is greater than ?_p. For the shear‐aligned PI/clay nanocomposites, an increase in the storage modulus with shear alignment is observed at ? < ?_p, whereas a decrease in the storage modulus is observed for ? > ?_p. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1000–1009, 2004     

Ionic liquids as reactive additives for the preparation and modification of epoxy networks

In this study, epoxy‐networked polymeric materials containing tributyl (ethyl) phosphonium diethyl phosphate (CYPHOS^®IL169) and trihexyl (tetradecyl) phosphonium bis 2,4,4‐(trimethyl pentyl)‐phosphinate (CYPHOS^®IL104) were developed from a mixture of epoxy prepolymer (DGEBA) and different amounts of ionic liquids (10–20–30 phr). Then, the effect of the chemical nature of ionic liquids on the final properties of epoxy networks was studied. Thus, the use of phosphonium salts as new additives led to the network with a high conversion of epoxy group (>90%), a high glass transition temperature T_g (>90 °C), adjustable in function of the counteranion and an increase of the storage modulus. In addition, the hydrophobic behavior and the thermal stability of the materials were also investigated by sessile drop method and thermogravimetric analyses. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3463–3471     

Flame‐retardant epoxy resins with high glass‐transition temperatures. II. Using a novel hexafunctional curing agent: 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐yl‐tris(4‐aminophenyl) methane

We synthesized a novel phosphorus‐containing triamine [9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐yl‐tris(4‐aminophenyl) methane (dopo‐ta)] from the nucleophilic addition of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐oxide and pararosaniline chloride, using triethylamine as an acid receiver. We confirmed the structure of dopo‐ta by IR, mass, and NMR spectra and elemental analysis. dopo‐ta served as a curing agent for diglycidyl ether of bisphenol A (DGEBA) and dicyclopentadiene epoxy (hp7200). Properties such as the glass‐transition temperature (T_g), thermal decomposition temperature, flame retardancy, moisture absorption, and dielectric properties of the cured epoxy resins were evaluated. The T_g's of cured DGEBA/dopo‐ta and hp7200/dopo‐ta were 171 and 190 °C, respectively. This high T_g phenomenon is rarely seen in the literature after the introduction of a flame‐retardant element. The flame retardancy increased with the phosphorus content, and a UL‐94 V‐0 grade was achieved with a phosphorus content of 1.80 wt % for DGEBA/dopo‐ta/diamino diphenylmethane (DDM) systems and 1.46 wt % for hp7200/dopo‐ta/DDM systems. The dielectric constants for DGEBA/dopo‐ta and hp7200/dopo‐ta were 2.91 and 2.82, respectively, implying that the dopo‐ta curing systems exhibited low dielectric properties. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5971–5986, 2005     

Pressure‐volume‐temperature and glass transition behavior of silica/polystyrene nanocomposite

The pressure‐volume‐temperature (PVT) behavior and glass transition behavior of a 10 wt % silica nanoparticle‐filled polystyrene (PS) nanocomposite sample are measured using a custom‐built pressurizable dilatometer. The PVT data are fitted to the Tait equation in both liquid and glassy states; the coefficient of thermal expansion α, bulk modulus K, and thermal pressure coefficient γ are examined as a function of pressure and compared to the values of neat PS. The glass transition temperature (T_g) is reported as a function of pressure, and the limiting fictive temperature (T_f′) from calorimetric measurements is reported as a function of cooling rate. Comparison with data for neat PS indicates that the nanocomposite has a slightly higher T_g at elevated pressures, higher bulk moduli at all pressures studied, and its relaxation dynamics are more sensitive to volume. The results for the glassy γ values suggest that thermal residual stresses would not be reduced for the nanocomposite sample studied. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1131–1138