Morphology and fracture behavior of toughening‐modified poly(vinyl chloride)/organophilic montmorillonite composites

Toughening‐modified poly(vinyl chloride) (PVC)/organophilic montmorillonite (OMMT) composites with an impact‐modifier resin (Blendex 338) were prepared by melt intercalation, and their microstructures were investigated with wide‐angle X‐ray diffraction, transmission electron microscopy, and scanning electron microscopy. The mechanical properties of the PVC composites were examined in terms of the content of Blendex and OMMT, and the fracture toughness was analyzed with a modified essential work of fracture model. Intercalated structures were found in the PVC/OMMT composites with or without Blendex. Either Blendex or OMMT could improve the elongation at break and notched impact strength of PVC at proper contents. With the addition of 30 phr or more of Blendex, supertough behavior was observed for PVC/Blendex blends, and their notched impact strength was increased more than 3319% compared with that of pristine PVC. Furthermore, the addition of OMMT greatly improved both the toughness and strength of PVC/Blendex blends, and the toughening effect of OMMT on PVC/Blendex blends was much larger than that on pristine PVC. Blendex and OMMT synergistically improved the mechanical properties of PVC. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 286–295, 2004     

Diffusion of small molecules through modified poly(vinyl chloride) membranes

The transport properties of a set of four copolymers based on poly(vinyl chloride) (PVC) have been studied. The nucleophilic substitution of chlorine atoms with 4‐mercaptophenol sodium salt, 2‐thionaphthalene, 4‐(1‐adamantyl) thiophenol, and thiophenolate sodium salt as the nucleophiles has been performed, from low conversion levels (3%) to high levels (40%), and the permeability, solubility, and diffusivity of oxygen, nitrogen, carbon dioxide, and methane have been measured. The introduction of bulky groups to the PVC chain leads to chain separation and results in large increases in the free volume at conversions up to 10%. This brings about a 5‐fold increase in the diffusion coefficients that is almost independent of the bulkiness of the substituent. Solubility is little affected and instead tends to decrease as substitution progresses. The substitution of more than 10% of the chlorine atoms does not result in an improvement in the transport properties. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 964–971, 2002     

Preparation of conducting poly(vinyl chloride)/polyindole composites and freestanding films via chemical polymerization

This study covers the synthesis of conducting polyindole (PIN) homopolymer, poly(vinyl chloride)/polyindole (PVC/PIN) composites, and preparation of their freestanding films. PIN and composites were synthesized chemically by radicalic mechanism using FeCl₃ as an initiator. Films of PVC and PVC/PIN composites were prepared by casting on glass Petri dishes. Mechanical properties of films were examined by stress–strain experiments. From FTIR spectra of polymers, it was revealed that polymerization reaction occurred by 2–3 mechanism. The conductivities of polymers at different temperatures were also measured by four‐probe technique and found in the range 10^?4 to 10^?5 S cm^?1. Magnetic properties of the polymers were analyzed by Gouy scale measurements and were found that their conducting mechanisms are of polaron and bipolaron natures. Thermal properties of polymers were investigated by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) and found that they had shown adequate thermal stability. X‐ray diffraction (XRD) spectra showed the amorphous nature of the polymers. Scanning electron microscopy (SEM) was used for microstructural analysis. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1290–1298, 2010     

Migration of Additives from Poly(vinyl chloride) (PVC) Tubes into Aqueous Media

The stability and migration product of medical PVC tubes plasticized with polyadipates were investigated by ageing in phosphate buffer at pH 1.679 and water at different temperatures. Changes in the PVC tubes were studied by water absorption, weight loss, Fourier infrared spectroscopy (FTIR), differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA). The low molecular weight migration product that was released was extracted and silylanized before gas chromatography/mass spectroscopy (GC/MS) identification and quantification. After 70 days, the weight loss was less than 0.5% and only a small amount of adipic acid migrated when a tube was aged at 37°C in water and phosphate buffer (pH 1.679), and at 70°C in water after 56 days. However, when aged at 70 and 110°C, gradual deactivation of heat stabilizer after 21 days of ageing in buffer solution and separation of plasticizer from PVC matrix occurred. When the tube was aged at 110°C, significant degradation of both polyadipates and PVC were observed. Adipic acid and 1,4-butanediol monomers and oligomers of polyadipate were the major migration products from polyadipates in the water ageing solution, while only a relatively high amount of adipic acid was identified as the main product in the buffer ageing solution.     

Radiation effects on the thermal degradation of poly(vinyl chloride) and poly(vinyl alcohol)

Radiation effects on the formation of conjugated double bonds in the thermal degradation of poly(vinyl chloride) (PVC) and poly(vinyl alcohol) (PVA) were investigated. Thin films of PVC and PVA were either irradiated with γ-rays at ambient temperature (pre-irradiation) and then subjected to thermal treatment, or irradiated at elevated temperatures (in situ irradiation). An extensive enhancement of the thermal degradation was observed for the pre-irradiation of the PVC films, which was more effective than the effect of the in situ irradiation at the same absorption dose. For the PVA degradation, however, the effect of the in situ irradiation was larger than that of the pre-irradiation. The results were explained and related mechanisms were discussed based on radiation-induced chemical reactions and their individual contributions to the thermal degradation behaviors of the two polymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3089–3095, 1998     

Investigation at the chain segmental level of the miscibility of poly(vinyl chloride)/atactic poly(methyl methacrylate) blends

We employed high‐resolution ¹³C cross‐polarization/magic‐angle‐spinning/dipolar‐decoupling NMR spectroscopy to investigate the miscibility and phase behavior of poly(vinyl chloride) (PVC)/poly(methyl methacrylate) (PMMA) blends. The spin–lattice relaxation times of protons in both the laboratory and rotating frames [T₁(H) and T_1ρ(H), respectively] were indirectly measured through ¹³C resonances. The T₁(H) results indicate that the blends are homogeneous, at least on a scale of 200–300 Å, confirming the miscibility of the system from a differential scanning calorimetry study in terms of the replacement of the glass‐transition‐temperature feature. The single decay and composition‐dependent T_1ρ(H) values for each blend further demonstrate that the spin diffusion among all protons in the blends averages out the whole relaxation process; therefore, the blends are homogeneous on a scale of 18–20 Å. The microcrystallinity of PVC disappears upon blending with PMMA, indicating intimate mixing of the two polymers. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2390–2396, 2001     

Molecular orientation behavior of poly(vinyl chloride) as influenced by the nanoparticles and plasticizer during uniaxial film stretching in the rubbery stage

The structural evolution during uniaxial stretching of poly(vinyl chloride) films was studied using our real time spectral birefringence stretching machine. The effect of clay loading and the amount of plasticizer as well as the rate effects on the birefringence development and true mechanical response are presented with a final model summarizing the molecular phenomena during stretching. Mechano‐optical studies revealed that birefringence correlated with mechanical response (stress, strain, work) nonlinearly. This was primarily attributed to the preexisting strong network of largely amorphous chains connected via small crystallites that act as physical crosslinking points. These crystallites are not easily destroyed during the high‐speed stretching process as evidenced from the birefringence–true strain curves along with the X‐ray crystallinity measurements. At high speeds, the amorphous chains do not have enough time to relax and hence attain higher orientation levels. The crystallites, however, orient more efficiently when stretched at slow speeds. Apparently, some relaxation of the surrounding amorphous chains helps rotate the crystallites in the stretching direction. Overall birefringence is higher at high stretching speeds for a given true strain value. When the nanoparticles are incorporated, the orientation levels are increased significantly for both the crystalline and amorphous phases. Nanoplatelets increase the continuity of the network because they have strong interaction with the amorphous chains and/or crystallites. This in turn helps transfer the local stresses to the attached chains and increase the orientation levels of the chains. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 724–742, 2005     

Effects of microscale calcium carbonate and nanoscale calcium carbonate on the fusion,thermal, and mechanical characterizations of rigid poly(vinyl chloride)/calcium carbonate composites

A Haake torque rheometer equipped with an internal mixer has been used to study the influence of microscale calcium carbonate (micro‐CaCO₃) and nanoscale calcium carbonate (nano‐CaCO₃) on the fusion, thermal, and mechanical characteristics of rigid poly(vinyl chloride) (PVC)/micro‐CaCO₃ and PVC/nano‐CaCO₃ composites, respectively. The fusion characteristics discussed in this article include the fusion time, fusion temperature, fusion torque, and fusion percolation threshold (FPT). The fusion time, fusion temperature, and FPT of rigid PVC/calcium carbonate (CaCO₃) composites increase with an increase in the addition of micro‐CaCO₃ or nano‐CaCO₃. In contrast, the fusion torque of rigid PVC/CaCO₃ composites decreases with an increase in the addition of micro‐CaCO₃ or nano‐CaCO₃. The results of thermal analysis show that the first thermal degradation onset temperature (T_onset) of rigid PVC/micro‐CaCO₃ is 7.5 °C lower than that of PVC. Meanwhile, the glass‐transition temperature (T_g) of rigid PVC/micro‐CaCO₃ is similar to that of PVC. However, T_onset and T_g of PVC/nano‐CaCO₃ composites can be increased by up to 30 and 4.4%, respectively, via blending with 10 phr nano‐CaCO₃. Mechanical testing results for PVC/micro‐CaCO₃ composites with the addition of 5–15 phr micro‐CaCO₃ and PVC/nano‐CaCO₃ composites with the addition of 5–20 phr nano‐CaCO₃ are better than those of PVC. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 451–460, 2006     

Formation of crystalline inclusion compounds of poly (vinyl chloride) of different stereoregularity with γ-cyclodextrin

This work reports the formation and detailed characterization of the γ-cyclodextrin (γ-CD) inclusion compounds (ICs) formed with two poly (vinyl chloride) samples with different isotactic content. The ICs were characterized by X-ray diffraction, solid state ¹³C-NMR, solution ¹H-NMR, FT-infrared, differential scanning calorimetry, and thermogravimetric analysis. Experimental evidence of the inclusion of the guest polymer chains into the narrow channels created by the γ-CD crystalline host lattice has been obtained. Examination of coalesced poly (vinyl chlorides) (PVCs) obtained after the host γ-CD is removed reveals different characteristics specifically for the coalesced PVC sample with higher isotactic content. An increase in T_g was observed by DSC for this PVC. To the contrary, the T_g of the coalesced PVC sample with lower isotactic content is almost the same as that of the as-synthesized sample. Thermogravimetric analysis indicated that coalesced PVC with higher isotactic content acquires a degree of stabilization after modification by threading into and being extracted from its γ-CD IC. The results suggest that an irreversible conformational change takes place when PVC forms ICs with a solid host lattice like γ-CD. The PVC molecules extend and reorganize into a more stable conformation in the IC, consequently improving the properties of the coalesced sample. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2503–2513, 2007     

The effects of wood-flour on combustion and thermal degradation behaviors of PVC in wood-flour/poly(vinyl chloride) composites

The effects of wood-flour on combustion and thermal degradation behaviors of PVC in wood-flour/poly (vinyl chloride) composites (WF-PVC) were investigated by using cone calorimeter (CONE) and TGA. The results show that thermal degradation behavior of WF-PVC composites has obvious characteristics of that of PVC. Interactions occur between wood-flour and PVC during the combustion and thermal degradation of WF-PVC composites. The thermal degradation of wood-flour can be accelerated by pure PVC. Moreover, the char formation can be raised by adding wood-flour to PVC. Compared with PVC at all flaming stage, when heat flux is kept at 50 kW m⁻², the average heat release rate (av-HRR), the total heat release (THR), the total smoke production (TSP) and the average specific extinction area (av-SEA) of WF-PVC composites are respectively reduced by 44%, 9.2%, 25.8% and 29.9%. In WF-PVC composites, the wood-flour has remarkable effects on the properties of heat release and smoke release of PVC.     

Thermal properties of poly(vinyl chloride)/polyurethane blends

Blends of poly(vinyl chloride) and a polyurethane elastomer were investigated by DSC and tensile testing. Up to 30 wt% single glass transition was found. It was concluded that the polyurethane forms partly a true blend and is partly disperged in the continuous blend phase.     

用DSC研究线形多嵌段聚氨酯与聚氯乙烯、氯化聚氯乙烯共混相容性

用示差扫描量热法（DSC）研究了线形多嵌段聚氨酯（PU）与聚氯乙烯（PVC）、氯化聚氯乙烯（CPVC）共混相容性，说明了PU／VC、PU／CPVC的相容是由于共混物中形成了新的氢键的缘故．聚酯型聚氨酯与PVC、CPVC的相容性要好子聚酸型聚氨酯，CPVC与PU的相容性又要好于PVC．聚氨酯中硬段的引入不利于PU／PVC、PU／CPVC的相容性．     

Influence of a mixing solvent with tetrahydrofuran and N,N‐dimethylformamide on electrospun poly(vinyl chloride) nonwoven mats

We evaluated the effects of the solvent composition with respect to the solution concentration, applied electric field, and tip‐to‐collector distance on the morphology of electrospun poly(vinyl chloride) (PVC) fibers. The solvent volume ratio was strongly correlated with the diameter of the electrospun fibers with respect to the other processing parameters. Electrospun PVC fibers dissolved in tetrahydrofuran (THF) had diameters ranging from 500 nm to 6 μm; those dissolved in N,N‐dimethylformamide (DMF) had an average diameter of 200 nm. The diameters of the electrospun fibers were obtained from narrow to broad distributions with the solvent composition. Also, the diameters of fibers electrospun from a mixed solvent of THF and DMF were less than 1 μm. The mechanical properties of electrospun PVC nonwoven mats depended on the fiber orientation and linear velocity of the drum surface. With increasing linear velocity of the drum surface, electrospun PVC fibers were arranged toward the machine direction, and the dimensions of the spiral path were shorter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2259–2268, 2002     

Dielectric investigation of the glass relaxation in poly(vinyl acetate) and poly(vinyl chloride) under high hydrostatic pressure

Measurements of the complex relative permittivity of poly(vinyl acetate) from 35 °C to 190 °C and poly(vinyl chloride) from 90 °C to 150 °C in the frequency range 10^–2 –10⁷ Hz and the pressure range 1–5000 bar are reported. Details of the pressure generating system and of the dielectric equipment are described.     

Preparation of poly(vinyl chloride) latexes by polymerization of stabilized monomer droplets

Poly(vinyl chloride) latexes have been prepared by polymerization in micron and submicron sized monomer droplets. Monomer emulsions with excellent long time stability were obtained by diffusional swelling of vinyl chloride monomer into preformed, stable polydisperse pre-emulsions of water-insoluble oils or monodisperse, oligomer styrene seed particles. It was found that the size and size distribution of the final latex particles were determined by those of the parent monomer emulsions. Except for the secondary particles formed during polymerization, the size and size distributions of the latex particles were found to be com-parable to those of the monomer emulsions employed, indicating a complete nucleation of the parent emulsion droplets. The extent of secondary particle formation was found to be very dependent upon the emulsifier concentration as well as on the type and amount of initiator used. © 1995 John Wiley & Sons, Inc.     

聚氯乙烯支载三氯化铁试剂催化醛与乙酸酐反应合成 乙酰缩醛

聚氯乙烯支载三氯化铁(PVC-FeCl3)试剂在室温条件下能方便快速催化各类醛与乙酸酐反应,以良好产率(75%～96%)生成相应乙酰缩醛。     

Electrical conductivity of poly(vinyl chloride) obtained by photodehydrochlorination from laminated poly(vinyl chloride)/polypyrrole films

Poly(vinyl chloride) (PVC) has been converted to an electrically conductive structure by combined electrochemical and photochemical methods. PVC was cast on a polypyrrole (PPy) film electrode which had been electrochemically prepared. The PVC layer in the laminated PVC/PPy films was first dehydrochlorinated under the illumination of UV light, and the generated polyenes were subsequently doped with I₂ and FeCl₃. The maximum electrical conductivity achieved for such PVC film was 2.51 X 10^?2 and 8.63 10^?2 S cm^?1 after I₂ and FeCl₃ doping, respectively. The temperature dependence of the electrical conductivity showed different behavior in higher and lower temperature ranges. In the former (T > 243 K), the T^?1 law held, and the activation energy and bandgap were estimated as 0.25 and 0.49 eV, respectively. In the latter (T < 243 K), the conductivity mechanism followed the variable range hopping model (T^?1/4 law) in which the radius of the localized state wave function and the density of the localized states at the Fermi level were 1.25 × 10³ Å and 1.03 X 10¹⁵ eV^?1 cm^?3, respectively. © 1995 John Wiley & Sons, Inc.     

弹性体偶联剂结构对PVC/PPC性能的影响

NBR－PPC弹性体偶联剂能促进PPC（聚丙撑碳酸酯）与PVC（聚氯乙烯）之间的相容性，改善共混物的力学性能，并在共混体系中产生轻度交联。偶联剂组成在NBR／PPC比例为70／30，NBR（丁腈橡胶）含腈量为34％，BPO过氧化苯甲酸用量为2．5份时，共混物的综合力学性能最佳，但偶联剂预先硫化时间不宜过长．     

Viscometric study of poly(vinyl chloride)/poly(vinyl acetate) blends in various solvents

The intermolecular interactions between poly(vinyl chloride) (PVC) and poly(vinyl acetate) (PVAc) in tetrahydrofuran (THF), methyl ethyl ketone (MEK) and N,N^′-dimethylformamide (DMF) were thoroughly investigated by the viscosity measurement. It has been found that the solvent selected has a great influence upon the polymer-polymer interactions in solution. If using PVAc and THF, or PVAc and DMF to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+THF) or (PVAc+DMF) is less than in corresponding pure solvent of THF or DMF. On the contrary, if using PVAc and MEK to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+MEK) is larger than in pure solvent of MEK. The influence of solvent upon the polymer-polymer interactions also comes from the interaction parameter term Δb, developed from modified Krigbaum and Wall theory. If PVC/PVAc blends with the weight ratio of 1/1 was dissolved in THF or DMF, Δb<0. On the contrary, if PVC/PVAc blends with the same weight ratio was dissolved in MEK, Δb>0. These experimental results show that the compatibility of PVC/PVAc blends is greatly associated with the solvent from which polymer mixtures were cast. The agreement of these results with differential scanning calorimetry measurements of PVC/PVAc blends casting from different solvents is good.