Comparative behavior of polybutadiene and polynorbornene‐based latices prepared by dispersion ring‐opening metathesis polymerization with a poly(ethylene oxide) macromonomer

This study critically examines the similarities and differences between poly(ethylene oxide) (PEO) stabilized latices of polynorbornene and polybutadiene. Features such as the kinetics of copolymerization of norbornene and cyclooctadiene with a macromonomer of PEO, the particles' size and morphology, the type of copolymer formed, and the stability of these latices were investigated and the results obtained are considered. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2705–2716, 2004     

Synthesis and characterization of cis‐polybutadiene‐block‐syn‐polystyrene copolymers with a cyclopentadienyl titanium trichloride/modified methylaluminoxane catalyst

This article reports a practical method for preparing cis‐polybutadiene‐block‐syn‐polystyrene (cis‐PB‐b‐syn‐PS) copolymers with long crystallizable syndiotactic polystyrene (syn‐PS) segments chemically bonded with high cis‐1,4‐polybutadiene segments through the addition of styrene (ST) to a cis‐specific 1,3‐butadiene (BD) living catalyst composed of cyclopentadienyl titanium trichloride (CpTiCl₃) and modified methylaluminoxane (MMAO). The incorporation of ST into the living polybutadiene (PB) precursor remarkably depended on the polymerization temperature. A low temperature (?20 °C) suppressed the rate of ST incorporation, but a high temperature (50 °C) tended to decompose the livingness of the active species and enhance the rate of the aspecific ST polymerization initiated by MMAO. Consequently, temperatures of 0–25 °C seemed to be best for this copolymerization system. Because of the absence of ST livingness, the final products contained not only the block copolymer but also the homopolymers. Attempts to isolate the block copolymer were carried out with common solvent fractionation techniques, but the results were not sufficient. Cross‐fractionation chromatography was, therefore, used for the isolation of the cis‐PB‐b‐syn‐PS copolymer. The presence of long syn‐PS segments was confirmed by the observation of a strong endothermic peak at 260 °C in the differential scanning calorimetry curve. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2698–2704, 2004     

Nitroxide‐mediated free‐radical copolymerization of styrene with butyl acrylate

Controlled free‐radical copolymerization of styrene (S) and butyl acrylate (BA) was achieved by using a second‐generation nitroxide, N‐tert‐butyl‐N‐[1‐diethylphosphono‐(2,2‐dimethylpropyl)] nitroxide (DEPN), and 2,2‐azobisisobutyronitrile (AIBN) at 120 °C. The time‐conversion first‐order plot was linear, and the number‐average molecular weight increased in direct proportion to the ratio of monomer conversion to the initial concentration, providing copolymers with low polydispersity. The monomer reactivity ratios obtained were r_S = 0.74 and r_BA = 0.29, respectively. To analyze the convenience of applying the Mayo–Lewis terminal model, the cumulative copolymer composition against conversion and the individual conversion of each monomer as a function of copolymerization time were studied. The theoretical values of the propagating radical concentration ratio were also examined to investigate the copolymerization rate behavior. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4168–4176, 2004     

Effect of reaction parameters on the dispersion polymerization of 1‐vinyl‐2‐pyrrolidone

Nonporous hydrogel microspheres 0.1–1.3 μm in diameter were prepared by the dispersion copolymerization of 1‐vinyl‐2‐pyrrolidone and ethylene dimethacrylate as a crosslinking agent. The crosslinking was evidenced by solid state ¹³C NMR and elemental analysis. The effect of various parameters including selection of solvent (cyclohexane, butyl acetate), initiator (4,4′‐azobis(4‐cyanopentanoic acid), 2,2′‐azobisisobutyronitrile, dibenzoyl peroxide) and stabilizer on the properties of resulting microspheres has been studied. Dynamic light scattering and photographic examination were used for determination of the diameter and polydispersity of microspheres. Increasing concentration of steric stabilizer in the initial polymerization mixture decreased the particle size. The particle size depended on the molecular weight of polystyrene‐block‐hydrogenated polyisoprene stabilizer, but not on the number of PS and polybutadiene blocks in the styrene–butadiene block copolymer stabilizers. Dibenzoyl peroxide used as an initiator resulted in agglomeration of particles. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 653–663, 2000     

Copolymerization of the macromonomer poly(ethylene oxide) with styryl end group and styrene in the presence of poly(ε‐caprolactone) with 2,2,6,6‐tetramethylpiperidinyl‐1‐oxy end group by controlled radical mechanism

A copolymerization of macromonomer poly(ethylene oxide) (PEO) with a styryl end group (PEO_S) and styrene was successfully carried out in the presence of poly(ε‐caprolactone) (PCL) with 2,2,6,6‐tetramethylpiperidinyl‐1‐oxy end group (PCL_T). The resulting copolymer showed a narrower molecular weight distribution and controlled molecular weight. The effect of the molecular weight and concentration of PCL_T and PEO_S on the copolymerization are discussed. The purity of PEO_S exerted a significant effect on the copolymerization; when the diol contents of PEO macromonomer were greater than 1%, the crosslinking product was found. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2093–2099, 2004     

Cationic copolymerization behavior of cyclic ether monomers with norbornene‐containing cyclic carbonate or spiro–orthoether structure

Cationic ring‐opening copolymerizations of various cyclic ether compounds with volume expanding monomers bearing norbornene backbones [norbornene‐spiro orthocarbonate (N‐SOC) and norbornene‐cyclic carbonate (N‐CC)] were carried out in the presence of a thermally latent initiator 1 . The 10% weight loss decomposition temperatures (T_d10) and the volume changes on the copolymerizations were measured for these resultant products. In the comparison between copolymerizations of bifunctional epoxide 2 with N‐SOC and with N‐CC, it was found that N‐CC served as a more useful volume controllable comonomer than N‐SOC. The copolymerizations with N‐CC yielded the products with a decrease in the volume change (volume shrinkage) and with an increase in the monomer feed ratio of N‐CC; T_d10 was relatively similar to the homopolymer of epoxide 2 and was observed except when the proportion of N‐CC was more than 20% in the monomer feed ratio of N‐CC. In contrast, similar copolymerizations with N‐SOC did not exhibit such tendencies, probably because of the low efficiency of the copolymerization derived from the low miscibility of N‐SOC for the epoxide. The other copolymerization systems of other bi‐ and monocyclic ether compounds ( 3 – 6 and phenyl glycidyl ether) with N‐CC also indicated an almost similar tendency toward that of the copolymerization with epoxide 2 . © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5113–5120, 2004     

Poly(butylene terephthalate‐co‐5‐tert‐butyl isophthalate) copolyesters: Synthesis,characterization, and properties

A series of poly(butylene terephthalate) copolyesters containing 5‐tert‐butyl isophthalate units up to 50 mol %, as well as the homopolyester entirely made of these units, were prepared by polycondensation from a melt. The microstructure of the copolymers was determined by NMR to be random for the whole range of compositions. The effect exerted by the 5‐tert‐butyl isophthalate units on thermal, tensile, and gas transport properties was evaluated. Both the melting temperature (T_m) and crystallinity were found to decrease steadily with copolymerization, whereas the glass‐transition temperature (T_g) increased and the polyesters became more brittle. Permeability and solubility slightly increased with the content in substituted isophthalic units, whereas the diffusion coefficient remained practically constant. For the homopolyester poly(5‐tert‐butyl isophthalate), all these properties were found to deviate significantly from the general trend displayed by copolyesters, suggesting that a different structure in the solid state is likely adopted in this case. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 92–100, 2005     

Physically controlled,free‐radical polymerization of vaporized fluoromonomer on solid surfaces

Gas/vapor‐deposition polymerization (GDP) of vinyl monomer is expected to exhibit a unique polymerization behavior different from its polymerization in the liquid phase. Free‐radical GDP of 2,2,3,3,3‐pentafluoropropyl methacrylate (FMA) was carried out with a conventional free‐radical initiator (azobisisobutyronitrile) on substrate surfaces. A linear relationship between the number‐average molecular weight and polymer yield was observed, and the consecutive copolymerization of methyl methacrylate (MMA) and FMA led to the formation of block copolymer P(MMA‐block‐FMA). These results suggested that the GDP process on substrate surfaces has a living nature. During the process, the active species at growing chain ends may be immobilized on the deposit surface and restricted from the chain‐transfer reactions, resulting in a continuation of the propagation reaction. The GDP on substrate surfaces is therefore a physically controlled polymerization process. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2621–2630, 2004     

Synthesis and characterization of well‐defined poly(2‐hydroxyethyl methacrylate‐co‐styrene)‐graft‐poly(ε‐caprolactone) by sequential controlled polymerization

A new graft copolymer, poly(2‐hydroxyethyl methacrylate‐co‐styrene) ‐graft‐poly(?‐caprolactone), was prepared by combination of reversible addition‐fragmentation chain transfer polymerization (RAFT) with coordination‐insertion ring‐opening polymerization (ROP). The copolymerization of styrene (St) and 2‐hydroxyethyl methacrylate (HEMA) was carried out at 60 °C in the presence of 2‐phenylprop‐2‐yl dithiobenzoate (PPDTB) using AIBN as initiator. The molecular weight of poly (2‐hydroxyethyl methacrylate‐co‐styrene) [poly(HEMA‐co‐St)] increased with the monomer conversion, and the molecular weight distribution was in the range of 1.09 ～ 1.39. The ring‐opening polymerization (ROP) of ?‐caprolactone was then initiated by the hydroxyl groups of the poly(HEMA‐co‐St) precursors in the presence of stannous octoate (Sn(Oct)₂). GPC and ¹H‐NMR data demonstrated the polymerization courses are under control, and nearly all hydroxyl groups took part in the initiation. The efficiency of grafting was very high. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5523–5529, 2004     

Anionic homo‐ and copolymerization of double‐tailed macromonomers: A route to novel macromolecular architectures

The synthesis of model linear and star double‐comb polybutadienes, as well as molecular double‐brush polybutadienes, with two tails emanating from each branch point, is presented. The synthetic approach involves (1) the selective reaction of living polybutadienes with the two chlorines of 4‐(dichloromethylsilyl)styrene to make double‐tailed macromonomers and (2) the homopolymerization or copolymerization of the double‐tailed macromonomer, in situ without isolation, to produce the double brushes and double combs, respectively. The star double comb was synthesized by the reaction of living double‐comb polybutadiene with trichloromethylsilane. Characterization carried out by size exclusion chromatography, with differential refractometer and light scattering detectors, indicated that the synthesized polybutadienes had a high degree of molecular and structural homogeneity. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4070–4078, 2005     

Incorporation of ketone groups into poly(4‐hydroxystyrene)s main chain by radical copolymerization of 2,2‐diphenyl‐4‐methylene‐1,3‐dioxorane with O‐protected hydroxystyrenes and their photodegradable behavior

Here we report the incorporation of ketone groups into poly(4‐hydroxystyrene)s main chain by radical copolymerization of O‐protected hydroxystyrenes such as 4‐ethoxyethoxystyrene and 4‐acetoxystyrene with 2,2‐diphenyl‐4‐methylene‐1,3‐dioxorane (DPMD) followed by removal of the protective groups and the photodegradable behavior of obtained copolymers. The copolymerization of O‐protected hydroxystyrenes with DPMD gave the corresponding copolymers bearing DMPD‐derived ketone groups in the main chain, of which content could be controlled by changing monomer feed ratio. The ethoxyethyl and acetyl groups of the obtained copolymers were completely removed under acidic and basic conditions, respectively, to afford poly(4‐hydroxystyrene)s having ketone moieties in the main chain. The molecular weights of these copolymers decreased under photoirradiation due to the Norrish‐type reactions of the ketone groups distributed in the main chain. These results demonstrate that poly(4‐hydroxystyrene)s having ketone groups in the main chain possess good photo‐scissibility. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Triblock copolymer synthesis via controlled radical polymerization in solution using S‐tert‐alkyl‐N,N‐alkoxycarbonylalkyldithiocarbamate RAFT agents

This paper presents the solution homopolymerization, random and block copolymerization of acrylic monomers, mediated using an S‐(1,4‐phenylenebis(propane‐2,2‐diyl)) bis(N,N‐butoxycarbonylmethyldithiocarbamate) RAFT agent. Fair to good control was obtained over the solution homopolymerization of various acrylic monomers. Although inhibition periods were observed, nearly no retardation was found to occur. Satisfactory control was also obtained over the solution copolymerization of n‐butyl acrylate with methacrylic acid, mediated using this RAFT agent. Finally, triblock copolymer synthesis, starting from the macromolecular intermediates produced in the homo‐ and copolymerization experiments, was studied, and was shown to be successful. The observed relatively broad molar mass distributions could be explained by a partial decomposition of the dithiocarbamate‐based RAFT agent during synthesis and/or polymerization, for which strong indications were obtained by performing a careful MALDI‐ToF MS analysis. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6419–6434, 2006     

Synthesis of new amphiphilic and lypophilic polymer networks containing 2‐methyl‐ and 2‐nonyl‐2‐oxazoline by the macroinitiator method

New amphiphilic and lypophilic polymer networks were obtained by the copolymerization of 2‐methyl‐2‐oxazoline (MeOXA), and/or 2‐nonyl‐2‐oxazoline (NoOXA) and 2,2′‐tetramethylenebis(2‐oxazoline) (BisOXA), respectively, initiating the copolymerization by random copolymers of chloromethylstyrene and methyl methacrylate or of chloromethylstyrene and styrene (macroinitiator method). Potassium iodide was used as an activator agent and the reaction was carried out in benzonitrile at 110 °C. In general, the polymer gels were obtained with a yield of 62 to 88%. The networks were characterized by high‐resolution magic angle spinning (HRMAS) NMR spectroscopy and by its absorption of polar and nonpolar solvents. In the case of amphiphilic polymer networks, the absorption of solvents depends on the molar ratio of 2‐methyl‐ to 2‐nonyl‐2‐oxazoline inside the polymer network favoring the absorption of polar solvents with a higher content of 2‐methyl‐2‐oxazoline. These gels showed a maximal swelling degree of 13 mL of water, 20 mL of methanol, and 13 mL of chloroform, respectively, per g of polymer. The lypophilic polymer networks containing only 2‐nonyl‐2‐oxazoline showed a maximal swelling degree of 8 mL of toluene, 14 mL of chloroform, and 2 mL of methanol, respectively, per g of the lypophilic network. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 122–128, 2005     

Polymerization of 1,3‐dienes with functional groups. III. Free‐radical polymerization of N,N‐diethyl‐2‐methylene‐3‐butenamide

Free‐radical homo‐ and copolymerization behavior of N,N‐diethyl‐2‐methylene‐3‐butenamide (DEA) was investigated. When the monomer was heated in bulk at 60 °C for 25 h without initiator, rubbery, solid gel was formed by the thermal polymerization. No such reaction was observed when the polymerization was carried out in 2 mol/L of benzene solution with with 1 mol % of azobisisobutyronitrile (AIBN) as an initiator. The polymerization rate (R_p) equation was R_p ∝ [DEA]^1.1[AIBN]^0.51, and the overall activation energy of polymerization was calculated 84.1 kJ/mol. The microstructure of the resulting polymer was exclusively a 1,4‐structure where both 1,4‐E and 1,4‐Z structures were included. From the product analysis of the telomerization with tert‐butylmercaptan as a telogen, the modes of monomer addition were estimated to be both 1,4‐ and 4,1‐addition. The copolymerizations of this monomer with styrene and/or chloroprene as comonomers were also carried out in benzene solution at 60 °C. In the copolymerization with styrene, the monomer reactivity ratios obtained were r₁ = 5.83 and r₂ = 0.05, and the Q and e values were Q = 8.4 and e = 0.33, respectively. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 999–1007, 2004     

Chemo‐ and stereoselective polymerization of 3‐methylenehepta‐1,6‐Diene and Its thiol‐ene modification

Here we report on the coordination polymerization of a vinyl‐functionalized butadiene monomer, 3‐methylenehepta‐1,6‐diene (MHD) with exclusive conjugated diene chemoselectivity, high 1,2‐regioselectivity and moderate isotacticity (1,2‐selectivity > 99%, mm triad = 93%). Random copolymers of MHD and other conjugated diene (isoprene or myrcene) are also synthesized. The pendent vinyl groups of MHD homo or copolymers could be quantitatively converted into various functional groups via thiol‐ene click reaction. The resulting functionalized polybutadiene‐based material display versatile thermal and surface properties. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1031–1039     

Cationic copolymerization behavior of epoxide and 3‐isochromanone

Cationic copolymerization of n‐butyl glycidyl ether (BGE) and 3‐isochromanone (ICM) was investigated using trifluoromethanesulfonic acid (TfOH) as an initiator at 100 °C. In the copolymerization, the reactive site of ICM with the propagating cation was completely different from that in its homopolymerization: in the former, the propagating cation reacted with the carbonyl oxygen of ICM, while in the latter, the propagating cation reacted with the aromatic ring of ICM. In spite of the potential of ICM to undergo the homopolymerization, in the present copolymerization, ICM was consumed smoothly only in the presence of epoxide. As a result, the copolymerization proceeded in a statistic manner to afford the corresponding copolymer bearing ICM‐derived ester linkages distributed in the main chain. Cationic copolymerization of bisphenol A‐diglycidyl ether and ICM was also performed to synthesize the corresponding networked polymer. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4213–4220     

Synthesis of asymmetrically substituted head‐to‐head polyacetylenes from 2,3‐disubstituted‐1,3‐butadienes

Asymmetrically substituted head‐to‐head polyacetylenes with phenyl and triphenylamine, thienyl or pyrenyl side groups were synthesized through anionic or controlled radical polymerization of 2,3‐disubstituted‐1,3‐butadienes and subsequent dehydrogenation process. Anionic polymerizations of the designed monomers bearing pendent triphenylamine and thienyl group gave narrow disperse disubstituted precursor polybutadienes with exclusive 1,4‐ or 4,1‐structure, which were confirmed by GPC and NMR measurements. In addition, the monomers possessing pyrenyl group were polymerized via nitroxide mediated radical polymerization and the resulting polymers were obtained with controlled molecular weight and low polydispersities. These polybutadiene precursors were then dehydrogenated in the presence of 2,3‐dichloro‐5,6‐dicyano‐1,4‐benzoquinone. Thus asymmetrically substituted head‐to‐head polyacetylenes were obtained as indicated by ¹H NMR. The properties of polybutadiene precursors and the corresponding polyacetylenes were analyzed by UV–vis, DSC, and TGA. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 395–402     

Reversible addition–fragmentation transfer polymerization of p‐nitrophenyl acrylate and synthesis of diblock copolymers poly(p‐nitrophenyl acrylate)‐b‐polystyrene

Poly(p‐nitrophenyl acrylate)s (PNPAs) with different molecular mass and narrow polydispersity were successfully synthesized for the first time by reversible addition–fragmentation transfer (RAFT) polymerization with azobisisobutyronitrile (AIBN) as an initiator and [1‐(ethoxy carbonyl) prop‐1‐yl dithiobenzoate] as the chain‐transfer agent. Although the molecular mass of PNPAs can be controlled by the molar ratio of NPA to RAFT agent and the conversion, a trace of homo‐PNPA was found, especially at the early stage of polymerization. The dithiobenzoyl‐terminated PNPA obtained was used as a macro chain‐transfer agent in the successive RAFT block copolymerization of styrene (St) with AIBN as the initiator. After purification by two washings with cyclohexane and nitromethane to remove homo‐PSt and homo‐PNPA, the pure diblock copolymers, PNPA‐b‐PSt's, with narrow molecular weight distribution were obtained. The structural analysis of polymerization products by ¹H NMR and GPC verified the formation of diblock copolymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4862–4872, 2004     

Sequence‐controlled cationic ring‐opening copolymerization of spiroorthocarbonate and oxetane

Pseudo block and triblock copolymers were synthesized by the cationic ring‐opening copolymerization of 1,5,7,11‐tetraoxaspiro[5.5]undecane (SOC1) with trimethylene oxide (OX) via one‐shot and two‐shot procedures, respectively. When SOC1 and OX were copolymerized cationically with boron trifluoride etherate (BF₃OEt₂) as an initiator in CH₂Cl₂ at 25 °C, OX was consumed faster than SOC1. SOC1 was polymerized from the OX‐rich gradient copolymer produced in the initial stage of the copolymerization to afford the corresponding pseudo block copolymer, poly [(OX‐grad‐SOC1)‐b‐SOC1]. We also succeeded in the synthesis of a pseudo triblock copolymer by the addition of OX during the course of the polymerization of SOC1 before its complete consumption, which provided the corresponding pseudo triblock copolymer, poly[SOC1‐b‐(OX‐grad‐SOC1)‐b‐SOC1]. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3233–3241, 2006     

Cationic copolymerization of racemic‐β‐butyrolactone with L,L‐lactide: One‐pot synthesis of block copolymers

Cationic copolymerization of racemic‐β‐butyrolactone (β‐BL) with l,l ‐lactide (LA) initiated by alcohol and catalyzed by trifluoromethanesulfonic acid proceeding by activated monomer (AM) mechanism was investigated. Although both comonomers were present from the beginning in the reaction mixture, polymerization proceeded in sequential manner, with poly‐BL formed at the first stage acting as a macroinitiator for the subsequent polymerization of LA. Such course of copolymerization was confirmed by following the consumption of both comonomers throughout the process as well as by observing the changes of growing chain‐end structure using ¹H NMR. ¹³C NMR analysis and thermogravimetry revealed the block structure of resulting copolymers. The proposed mechanism of copolymerization was confirmed by the studies of changes of ¹H NMR chemical shift of acidic proton in the course of copolymerization, providing an indication that indeed protonated species and hydroxyl groups are present throughout the process, as required for AM mechanism. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4873–4884