Trialkoxysilane‐capped acrylic resin/titania organic–inorganic hybrid optical films prepared by the sol–gel process

Homogeneous organic–inorganic hybrid materials with excellent thermal and optical performance were successfully prepared via the mixing of (3‐methacryloxypropyl)trimethoxysilane‐capped acrylic resin with titania synthesized by sol–gel approaches. The effects of the titania content, amount of water, and pH in the sol–gel and the ratio of the solvents (butyl acetate and ethanol) on the structures and properties of the hybrid materials were studied. More titania, more water, and base catalysis in the sol–gel process and a higher ratio of butyl acetate to ethanol for the hybrids led to a larger size and a more compact structure of the titania phase. Increasing the titania content dramatically improved the glass‐transition temperature, UV‐shielding properties, and refractive index for the hybrid materials, and it did not reduce their optical transparency. In general, better thermal stability and optical properties were achieved for the hybrid materials prepared with less water, lower pH values (e.g., acidic or neutral conditions), and a lower ratio of butyl acetate to ethanol. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 637–649, 2005     

High‐refractive‐index thin films prepared from aminoalkoxysilane‐capped pyromellitic dianhydride–titania hybrid materials

High‐refractive‐index aminoalkoxysilane‐capped pyromellitic dianhydride (PMDA)–titania hybrid optical thin films (TP0–TP8) were synthesized and characterized in this study. They were prepared with PMDA, aminopropyltrimethoxysilane, and titanium(IV) isopropoxide via a sol–gel process followed by spin coating and multistep baking. Through adjustments in the concentration and reaction time, the inorganic content in the hybrid thin films could be as high as 59.1 wt %. The Fourier transform infrared results indicated successful bonding between the organic and inorganic moieties. However, residues of the chelating ligands were found in the hybrids with high titania contents, affecting their thermal and optical properties. Field emission scanning electron microscopy results suggested a nanosized domain of the titania segment in the hybrid materials TP0–TP8. An atomic force microscopy study suggested that the hybrid thin films had good planarization. The dispersions of the refractive index and extinction coefficient in the wavelength range 190–900 nm were studied. The refractive indices of the prepared hybrid thin films at 633 nm increased linearly from 1.567 to 1.780 with increasing titania content. However, the Abbe numbers of the hybrid thin films showed an opposite trend. Excellent optical transparence was obtained in the visible region for the prepared hybrid thin films. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3419–3427, 2001     

Organic–inorganic polymeric nanocomposites involving novel titanium tetraisopropylate in polyethylene–octene elastomer

The new nanocomposites, by means of an in situ sol–gel process consisting of metallocene polyethylene–octene elastomer (POE) and titanium tetraisopropylate (TTIP), were investigated. In addition, the acrylic acid grafted POE (POE‐g‐AA) was studied as an alternative to POE. Fourier transform infrared (FTIR) spectroscopy, a dynamic mechanical analyzer (DMA) spectrometer, an X‐ray diffractometer (XRD), differential scanning calorimetry (DSC), a thermogravimetric analyzer (TGA), an Instron mechanical tester, and a scanning electron microscope (SEM) were used to characterize and examine the samples. The results indicate that the POE‐g‐AA/TiO₂ hybrid could have a positive effect on the properties of the POE/TiO₂ hybrid because the carboxylic acid groups of acrylic acid should act as coordination sites for the titania phase to form a Ti? O? C chemical bond. The strength of interfacial bonding between the polymer chains and the ceramic phase depended on the amount of TiO₂, as shown by the change in glass‐transition temperature (T_g) with TiO₂ content. The result of mechanical and thermal tests showed that both the tensile strength and the T_g increased to a maximum value and then decreased with an increasing of TiO₂ because excess particles (e.g., greater than 10 wt % TiO₂) might cause separation or segregation between the organic and inorganic phases. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4272–4280, 2004     

Synthesis of the (hydroxypropyl)cellulose–titania hybrid nanocomposite as seen by Raman spectroscopy

The nanocomposite of the (hydroxypropyl)cellulose–titania hybrid was prepared using the (hydroxypropyl)cellulose (HPC) and (tetra‐isopropyl)orthotitanate (TIPT) modified by the methacrylic acid (MAA) as a sol–gel precursor. The Raman investigations of the TIPT with MAA mixtures revealed that these mixtures formed an intermolecular complex determined by the non‐hydrolytic condensation of the constituents. In spite of this, the MAA/TIPT precursor can be used as a solvent for the HPC. The high viscosity of the homogenous liquid of HPC in the TIPT/MAA system was obtained and the sol–gel process under an influence of the moisture from the air could be conducted. The Raman investigations of HPC–titania hybrid showed octahedrally coordinated titania atoms [TiO₆] embodied in the HPC environment. Although the chelating bond between the octahedrally coordinated titania [TiO₆] and the MAA still occurred. The nanosize properties of TiO₂ prepared by calcinations of HPC–titania hybrids were studied by the Raman spectroscopy, X‐ray investigations and the scanning electron microscopy (SEM). Copyright © 2007 John Wiley & Sons, Ltd.     

Organic–inorganic hybrid networks by the sol–gel process and subsequent photopolymerization

Organic–inorganic hybrid materials were prepared by a convenient two‐step curing procedure based on sol–gel condensation and subsequent photopolymerization. Novel bismethacrylate‐based hybrid monomers with pendant, condensable alkoxysilane groups were prepared by Michael addition and possessed number‐average molecular weights between 580 and 1600 g/mol. The formation of inorganic networks by sol–gel condensation of the alkoxysilane groups in the presence of aqueous methacrylic acid was monitored with rheological measurements. The condensation conversion was monitored with solid‐state ²⁹Si cross‐polarization/magic‐angle spinning NMR spectroscopy. Subsequent photopolymerization led to organic–inorganic hybrid networks and low volume shrinkage, ranging from 4.2 to 8.3%, depending on the molecular weight of the hybrid monomer applied. Highly filled composite materials with glass filler fractions greater than 75% showed attractive mechanical properties with Young's moduli of 2700–6200 MPa. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4274–4282, 2001     

Preparation of MEH‐PPV/nanosized titania hybrids via in situ sol–gel reaction of titanium alkoxide: Optical property

Homogenously dispersed organic (MEH‐PPV)/inorganic (nanosized titania) hybrids were successfully synthesized. The method of preparation was based on a simple one‐step in situ sol–gel technique using titanium isopropoxide (TIP) as the precursor. The key benefit of this preparation was that TIP interacted with both 2‐chlorophenol and MEH‐PPV, so that the degree of aggregation and phase separation could be kept to a minimum with a suitable recipe. MEH‐PPV/TIP/H₂O/2‐chlorophenol of various weight ratios were synthesized to examine the morphology as well as optical properties of the MEH‐PPV/TIP(titania) hybrid. The observation of MEH‐PPV gelation and Fourier transform infrared results verified the interaction existing between MEH‐PPV and TIP. SEM photographs showed that TIP(titania) were homogenously dispersed in the MEH‐PPV film if the hybrid solution was clear from the use of a suitable recipe. UV–vis absorption measurements showed that the addition of TIP decreased the conjugation length of MEH‐PPV. A redshift in the photoluminescence (PL) emission was observed in almost all the hybrids in the solution state, because of the aggregation of MEH‐PPV. However, it was found that spinning destroyed the aggregation of MEH‐PPV, resulting in a blueshift in the PL emission of the hybrids. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 515–529, 2008     

A comparative study of phosphoric acid‐doped m‐PBI membranes

Phosphoric acid (PA)‐doped m‐polybenzimidazole (PBI) membranes used in high temperature fuel cells and hydrogen pumps were prepared by a conventional imbibing process and a sol–gel fabrication process. A comparative study was conducted to investigate the critical properties of PA doping levels, ionic conductivities, mechanical properties, and molecular ordering. This systematic study found that sol–gel PA‐doped m‐PBI membranes were able to absorb higher acid doping levels and to achieve higher ionic conductivities than conventionally imbibed membranes when treated in an equivalent manner. Even at similar acid loadings, the sol–gel membranes exhibited higher ionic conductivities. Heat treatment of conventionally imbibed membranes with ≤29 wt % solids caused a significant reduction in mechanical properties; conversely, sol–gel membranes exhibited an enhancement in mechanical properties. From X‐ray structural studies and atomistic simulations, both conventionally imbibed and sol–gel membranes exhibited d‐spacings of 3.5 and 4.6 Å, which were tentatively attributed to parallel ring stacking and staggered side‐to‐side packing, respectively, of the imidazole rings in these aromatic heterocyclic polymers. An anisotropic staggered side‐to‐side chain packing present in the conventional membranes may be related to the reduction in mechanical properties. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Polym. Phys. 2014 , 52, 26–35     

Microstructure and Properties of Triethoxysilylpropylamine-Capped Polyurethane/Titania Hybrid Films

Triethoxysilylpropylamine-capped waterborne polyurethane/titania hybrid films were prepared by in situ method via sol-gel process of titanium n-butoxide under acidic condition. In the paper, we studied the effect of the contents of titania sol on the microstructure, mechanical property, water resistance, and optical property of the hybrid films. It was found, with introducing the content of titania, some physical properties such as tensile strength, modulus, water resistance, refractive index, heat resistance, and ultraviolet absorbance will increase. SEM and SAXS study suggested that the hybrid films had good planarization.     

Preparation of photocrosslinked sol‐gel composites based on urethane‐acrylic matrix,silsesquioxane sequences,TiO2, and Ag/Au Nanoparticles for use in photocatalytic applications

An acid urethane oligodimethacrylate based on poly(ethylene glycol) was synthesized and used in the preparation of hybrid composites containing silsesquioxane sequences and titania domains formed through sol‐gel reactions along with silver/gold nanoparticles (Ag/Au NPs) in situ photogenerated during the UV‐curing process. The photopolymerization kinetics studied by Fourier transform infrared spectroscopy and photoDSC showed that the photoreactivity of the investigated formulations depends on the amount of titanium butoxide (5–20 wt %) added in the system subjected to UV irradiation. The introduction of 1 wt % AgNO₃/AuBr₃ in formulations slightly improved the degree of conversion but diminished the polymerization rates. The formation of hybrid materials comprising predominantly amorphous TiO₂/SiO₂ NPs, with or without Ag/Au NPs, was confirmed through specific analyses. The evaluation of photocatalytic activity demonstrated that the synthesized hybrid films are suitable for the complete removal of organic pollutants (phenolic compounds) from water under UV irradiation (200–350 min) at low intensity (found in the solar radiation). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1189–1204     

Preparation of poly(methyl acrylate‐co‐itaconic anhydride)/SiO2 hybrid materials via the sol–gel process—The effect of the coupling agent,inorganic content,and nature of the catalyst

Transparent poly(methyl acrylate‐co‐itaconic anhydride)/SiO₂ hybrid materials were prepared from methyl acrylate‐itaconic anhydride copolymer and tetraethoxysilane (TEOS) with the coupling agent (3‐aminopropyl)triethoxysilane (APTES) via a sol–gel process. The covalent bonds between the organic and inorganic phases were introduced by the in situ aminolysis of the itaconic anhydride units with APTES forming a copolymer bearing a triethoxysilyl group. These groups subsequently were hydrolyzed with TEOS and allowed to form a network. These reactions were monitored by Fourier transform infrared analysis. The amount of APTES had a dramatic influence on the gel time and sol fraction. The effect of APTES, the inorganic content, and the nature of the catalyst on the thermal properties and morphology of the hybrid materials were studied by differential scanning calorimetry, thermogravimetric analysis, scanning electron microscopy, and atomic force microscopy. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 321–328, 2000     

Synthesis and characterization of UV‐curable phosphorus containing hybrid materials prepared by sol–gel technique

In this study, a series of ultraviolet (UV)‐curable organic–inorganic hybrid coating materials containing phosphorus were prepared by sol–gel approach from acrylate end‐capped urethane resin, acrylated phenyl phosphine oxide oligomer (APPO), and inorganic precursors. TEOS and MAPTMS were used to obtain the silica network and Ti:acac complex was employed for the formation of the titania network in the hybrid coating systems. Coating performance of the hybrid coating materials applied on aluminum substrates was determined by the analysis techniques, such as hardness, gloss, impact strength, cross‐cut adhesion, taber abrasion resistance, which were accepted by international organization. Also, stress–strain test of the hybrids was carried out on the free films. These measurements showed that all the properties of the hybrids were enhanced effectively by gradual increase in sol–gel precursors and APPO oligomer content. The thermal behavior of the hybrid coatings was investigated by thermogravimetric analysis (TGA) analysis. The flame retardancy of the hybrid materials was examined by the limiting oxygen index (LOI); the LOI values of pure organic coating (BF) increased from 31 to 44 for the hybrid materials containing phosphorus (BF‐P:40/Si:10). The data from thermal analysis and LOI showed that the hybrid coating materials containing phosphorus have higher thermal stability and flame resistance properties than the organic polymer. Besides that, it was found that the double bond conversion values for the hybrid mixtures were adequate in order to form an organic matrix. The polycondensation reactions of TEOS and MAPTMS compounds were also investigated by ²⁹Si‐NMR spectroscopy. SEM studies of the hybrid coatings showed that silica/titania particles were homogenously dispersed through the organic matrix. In addition, it was determined that the hybrid material containing phosphorus and silica showed fibrillar structure. Copyright © 2009 John Wiley & Sons, Ltd.     

Microstructure and properties of 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA)‐p‐phenylene diamine (PDA) polyimide/poly(vinylsilsesquioxane) hybrid nanocomposite films

Hybrid nanocomposite films of poly(vinylsilsesquioxane) (PVSSQ) and polyimide (PI) (PI/PVSSQ) were prepared via sol‐gel process from triethoxyvinylsilane (VSSQ) and thermal imidization from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA)‐p‐phenylene diamine (PDA) polyamic acid (BPDA‐PDA PAA). We investigated the microstructure; interfacial interaction; and optical, thermal, dielectric, and mechanical properties of the hybrid films. The phase morphologies and degree of surface roughness were evaluated by scanning electron microscope (SEM) and atomic force microscope (AFM), respectively. It was found that the surface topography was influenced by the composition of PVSSQ. Hydrogen bonding interactions between polyimide (PI) matrix and PVSSQ domains were proved with FT‐IR spectroscopy. The transparency of the hybrid films was found to be dependent on the PVSSQ content. Incorporating of the PVSSQ in the hybrid composites increased the glass transition temperature of PI. Dielectric constants of the hybrid films were in the range of 2.37–3.59. Properties of the PI films were also significantly enhanced by adding 5–30 wt % of PVSSQ. For comparison, we also prepared the hybrid composites of PI and mixtures of VSSQ and tetraethoxysilane (TEOS) and the PI/silica hybrid composite containing 30 wt % of silica obtained from TEOS. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5189–5199, 2004     

Ternary luminescent lanthanide-centered hybrids with organically modified titania and polymer units

Nicotinic acid (NA) is grafted to titanium alkoxide to achieve functional precursor Ti-NA, which then is coordinated to lanthanide ions (Tb³⁺/Eu³⁺) to prepare the binary titania hybrid materials Ti-NA-Eu/Ti-NA-Tb via a sol–gel process in the presence of water. Furthermore, two types of ternary titania hybrid materials, Ti-NA-Ln-PMAA/Ti-NA-Ln-PVP, are assembled by the introduction of the organic polymers polymethacrylic acid (PMAA)/polyvinylpyrrolidone (PVP) into the above system. The FTIR spectra of these titania hybrid materials confirm their basic composition, and the X-ray diffraction patterns reveal that they are amorphous. Luminescence spectra and lifetimes of these titania hybrids are recorded, revealing that these hybrid materials with organic polymers exhibit longer luminescence lifetimes and higher quantum efficiencies.     

The effect of silver doping on photocatalytic properties of titania multilayer membranes

In this investigation an Ag doped titania multilayer membrane is successfully fabricated via the sol–gel processing method. The doped membrane is characterized via X-ray Diffraction and N₂-sorption techniques and the photocatalytic properties of the membrane are investigated via methyl orange degradation. The properties included high surface area (101 m²/g), small pore size (3.1 nm), and active anatase crystal phase. The prepared titania membrane has a high photocatalytic activity and decomposes methyl orange by 50% after 9 h of UV irradiation. The prepared membrane can be applied in the development of efficient photocatalytic systems for the treatment of water. Due to the high photoactivity of the prepared titania membrane, this study reveals the possibility of combining two processes for removal of organic pollutants: the photocatalytic process and the membrane separation process. In the combining process the lifetime of the membrane increases and the quality of water is enhanced.     

溶胶-凝胶法制备丙烯酸树脂/TiO2有机-无机杂化材料及其结构表征

通过预水解的二氧化钛(TiO2 )溶胶与丙烯酸树脂共混或原位聚合的方法制备了均匀透明的丙烯酸树脂 TiO2 有机 无机杂化材料.考察了TiO2 溶胶制备方法、聚合物中—COOH官能团含量和杂化材料制备方法对杂化材料结构的影响.索氏抽提实验表明聚合物中的羧酸官能团和无机TiO2 相间发生了交联反应,且随着—COOH官能团含量的增加,交联程度增大.小角X射线散射(SAXS)结果发现,杂化材料中TiO2 为疏松的三维网状结构,且在纳米尺度范围内,但这种三维网状结构随着TiO2 溶胶制备中水或酸的用量增加,其致密度增加,尺寸增大.同原位聚合法相比,共混法可制备出更均匀的杂化体系,且TiO2 为单分散.     

Solid polymer electrolytes. VI. Microstructure of organic–inorganic hybrid networks composed of 3‐glycidoxypropyltrimethoxysilane and LiClO4 and affected by different synthetic routes

Hybrid organic–inorganic materials derived from 3‐glycidoxypropyltrimethoxylsilane were prepared via two different synthetic routes: (1) the HCl‐catalyzed sol–gel approach of silane followed by the lithium perchlorate (LiClO₄)/HCl‐catalyzed opening of epoxide and (2) the simultaneous gelation of tin/LiClO₄‐catalyzed silane/epoxide groups. LiClO₄ catalyzed the epoxide polymerization, and its effects on the structures of these hybrid materials were studied by NMR. The structure of the inorganic side was probed by solid‐state ²⁹Si NMR spectroscopy, and the characterizations of the organic side and the chemical processes involved in the different synthetic routes were performed with solid‐state cross‐polarity/magic‐angle‐spinning ¹³C NMR. The different synthetic routes significantly affected the polymerization behaviors of the organic and inorganic sides in the presence of LiClO₄. A larger amount of LiClO₄ promoted the opening of epoxide and led to the formation of longer poly(ethylene oxide) chains via the HCl‐catalyzed sol–gel approach, whereas in the case of the tin‐catalyzed approach, the faster polymerization of the inorganic side hindered the growth of the organic network. The addition of LiClO₄ was proven to be without crystalline salt present in the hybrid networks by wide‐angle X‐ray powder diffraction. Also, the interactions between the ions and hybrid host, examined with Fourier transform infrared and ⁷Li proton‐decoupled magic‐angle‐spinning NMR, further demonstrated that extensive ion aggregation existed in these hybrid materials. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 151–161, 2004     

Preparation,characterization, and properties of novolac‐type phenolic/SiO2 hybrid organic–inorganic nanocomposite materials by sol–gel method

This article describes the preparation of novolac‐type phenolic resin/silica hybrid organic–inorganic nanocomposite, with a sol–gel process. The coupling agent was used to improve the interface between the organic and inorganic phases. The effect of the structure of the nanocomposite on its physical and chemical properties is discussed. The coupling agent reacts with the resin to form covalent bonds. The structure of the modified hybrid nanocomposites was identified with a Fourier transform infrared spectroscope. The silica network was characterized by nuclear magnetic resonance imaging (²⁹Si NMR). Results revealed that Q₄ (tetrasubstituted) and T₃ (trisubstituted) are the dominant microstructures. The size of the silica in the phenolic resin was characterized with a scanning electron microscope. The size of the particles of inorganic silica in the modified system was less than 100 nm. The nanocomposite exhibited good transparency. Moreover, the thermal and mechanical properties exhibited significant improvement. The modified hybrid composite exhibited favorable thermal properties. The temperature at which a weight loss of 5% occurred increased from 281 to 350 °C. The flexural strength increased by 6–30%. The limiting oxygen index of the nanocomposite reached 37, and the Underwriters Laboratory test was 94V‐0. Consequently, these materials possess excellent flame‐retardant properties. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 905–913, 2003     

Flexible nanocrystalline‐titania/polyimide hybrids with high refractive index and excellent thermal dimensional stability

In this study, a novel synthetic route was developed to prepare polyimide–nanocrystalline–titania hybrid optical films with a relatively high titania content (up to 50 wt %) and thickness (20–30 μm) from soluble polyimides containing hydroxyl groups. Two series of newly soluble polyimides were synthesized from the hydroxy‐substituted diamines with various commercial tetracarboxylic dianhydrides. The hydroxyl groups on the backbone of the polyimides could provide the organic–inorganic bonding and resulted in homogeneous hybrid solutions by controlling the mole ratio of titanium butoxide/hydroxyl group. AFM, SEM, TEM, and XRD results indicated the formation of well‐dispersed nanocrystalline‐titania. The flexible hybrid films could be successfully obtained and revealed relatively good surface planarity, thermal dimensional stability, tunable refractive index, and high optical transparency. A three‐layer antireflection coating based on the hybrid films was prepared and showed a reflectance of less than 0.5% in the visible range indicated its potential optical applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1433–1440, 2010     

Acrylic polymer/silica organic–inorganic hybrid emulsions for coating materials: Role of the silane coupling agent

Acrylic polymer/silica organic–inorganic hybrid emulsions were synthesized by a simple method, that is, a conventional emulsion polymerization and subsequent sol–gel process, to provide water‐based coating materials. The acrylic polymer emulsions contained a silane coupling agent monomer, such as methacryloxypropyltriethoxysilane, to form highly solvent‐resistant hybrid films. On the other hand, the hybrid films from the surface‐modified polymer emulsions, in which the silane coupling agent was located only on the surface of the polymer particles and the particle core was not crosslinked, did not exhibit high solvent resistance. A honeycomblike array structure, which was derived from the polymer particles (diameter ≈ 50 nm) and the silica domain, on the hybrid film surfaces was observed by atomic force microscopy. The crosslinked core part and silane coupling agent containing the shell part of the polymer particles played important roles in attaining high solvent resistance. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4736–4742, 2006     

Mechanically controlled, morphologically determined sol–gel derived UV curable hybrid nanocomposites: SAXS and DMTA studies

This work reports preparation of organic–inorganic hybrid materials by sol–gel method. To this end, UV cured urethane acrylate and different functional monomers were used as organic network together with tetraethyl orthosilicate (TEOS) as inorganic network former and 3-methacryloxy propyltrimethoxy silane (MEMO) as network modifier. The effect of sol–gel precursor’s ratio on morphological properties of hybrid network was studied by small angle X-ray scattering (SAXS). Dynamic mechanical thermal analysis (DMTA) was performed to investigate the mechanical behavior of hybrid films. Whilst hybrids with low content of TEOS and high amounts of MEMO represented a “structural defect”, it was found that by increasing TEOS/MEMO ratio, the silica domain size decreased, showing a mass fractal behavior. This was attributed to a more compact structure of silica and a stronger hybrid network. The changes observed in compactness of hybrid films directly affected the glass transition temperature. By increasing the inorganic phase, more restriction in segmental motion of the polymeric phase occurred. Upon increasing TEOS/MEMO ratio a broader tan δ peak deduced from DMTA graphs was observed, indicating greater phase separation and higher heterogeneity.