Crystallization kinetics and melting behavior of syndiotactic 1,2‐polybutadiene

Differential scanning calorimetry was used to investigate the isothermal crystallization, subsequent melting behavior, and nonisothermal crystallization of syndiotactic 1,2‐polybutadiene (st‐1,2‐PB) produced with an iron‐based catalyst system. The isothermal crystallization of two fractions was analyzed according to the Avrami equation. The morphology of the crystallite was observed with polarized optical microscopy. Double melting peaks were observed for the samples isothermally crystallized at 125–155 °C. The low‐temperature melting peak, which appeared approximately 5 °C above the crystallization temperature, was attributed to the melting of imperfect crystals formed by the less stereoregular fraction. The high‐temperature melting peak was associated with the melting of perfect crystals formed by the stereoregular fraction. With the Hoffman–Weeks approach, the value of the equilibrium melting temperature was derived. During the nonisothermal crystallization, the Ozawa method was limited in obtaining the kinetic parameters of st‐1,2‐PB. A new method that combined the Ozawa method and the Avrami method was employed to analyze the nonisothermal crystallization of st‐1,2‐PB. The activation energies of crystallization under nonisothermal conditions were calculated. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 553–561, 2005     

Isothermal and nonisothermal crystallization kinetics of nylon‐46

Isothermal and nonisothermal crystallization kinetics of nylon‐46 were investigated with differential scanning calorimetry. The equilibrium melting enthalpy and the equilibrium melting temperature of nylon‐46 were determined to be 155.58 J/g and 307.10 °C, respectively. The isothermal crystallization process was described by the Avrami equation. The lateral surface free energy and the end surface free energy of nylon‐46 were calculated to be 8.28 and 138.54 erg/cm², respectively. The work of chain folding was determined to be 7.12 kcal/mol. The activation energies were determined to be 568.25 and 337.80 kJ/mol for isothermal and nonisothermal crystallization, respectively. A convenient method was applied to describe the nonisothermal crystallization kinetics of nylon‐46 by a combination of the Avrami and Ozawa equations. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1784–1793, 2002     

Nonisothermal crystallization and melting behavior of a luminescent conjugated polymer,poly(9,9‐dihexylfluorene‐alt‐co‐2,5‐didecyloxy‐1,4‐phenylene)

The nonisothermal crystallization kinetics of a luminescent conjugated polymer, poly(9,9‐dihexylfluorene‐alt‐co‐2,5‐didecyloxy‐1,4‐phenylene) (PF6OC10) with three different molecular weights was investigated by differential scanning calorimetry under different cooling rates from the melt. With increasing molecular weight of PF6OC10, the temperature range of crystallization peak steadily became narrower and shifted to higher temperature region and the crystallization rate increased. It was found that the Ozawa method failed to describe the nonisothermal crystallization behavior of PF6OC10. Although the Avrami method did not effectively describe the nonisothermal crystallization kinetics of PF6OC10 for overall process, it was valid for describing the early stage of crystallization with an Avrami exponent n of about 3. The combined method proposed in our previous report was able to satisfactorily describe the nonisothermal crystallization behavior of PF6OC10. The crystallization activation energies determined by Kissinger, Takhor, and Augis‐Bennett models were comparable. The melting temperature of PF6OC10 increased with increasing molecular weight. For low‐molecular‐weight sample, PF6OC10 showed the characteristic of double melting phenomenon. The interval between the two melting peaks decreased with increasing molecular weight, and only one melting peak was observed for the high‐molecular‐weight sample. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 976–987, 2007     

Thermal,crystallization, mechanical,and rheological characteristics of poly(trimethylene terephthalate)/poly(ethylene terephthalate) blends

Blends of poly(trimethylene terephthalate) (PTT) and poly(ethylene terephthalate) in the amorphous state were miscible in all of the blend compositions studied, as evidenced by a single, composition‐dependent glass‐transition temperature observed for each blend composition. The variation in the glass‐transition temperature with the blend composition was well predicted by the Gordon–Taylor equation, with the fitting parameter being 0.91. The cold‐crystallization (peak) temperature decreased with an increasing PTT content, whereas the melt‐crystallization (peak) temperature decreased with an increasing amount of the minor component. The subsequent melting behavior after both cold and melt crystallizations exhibited melting point depression behavior in which the observed melting temperatures decreased with an increasing amount of the minor component of the blends. During crystallization, the pure components crystallized simultaneously just to form their own crystals. The blend having 50 wt % of PTT showed the lowest apparent degree of crystallinity and the lowest tensile‐strength values. The steady shear viscosity values for the pure components and the blends decreased slightly with an increasing shear rate (within the shear rate range of 0.25–25 s^?1); those of the blends were lower than those of the pure components. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 676–686, 2004     

Nonisothermal cold crystallization behavior and kinetics of polylactide/clay nanocomposites

The nonisothermal cold crystallization behavior of intercalated polylactide (PLA)/clay nanocomposites (PLACNs) was studied using differential scanning calorimetry, polarized optical microscope, X‐ray diffractometer, dynamic mechanical thermal analysis, and Fourier transform infrared spectrometer. The results show that both the cold crystallization temperature (T_cc) and melting point (T_m) of PLA matrix decreases monotonously with increasing of clay loadings, accompanied by the decreasing degree of crystallinity (X_c%) at the low heating rates (≤5 °C/min). However, the X_c% of PLACNs presents a remarkable increase at the high heating rate of 10 °C/min in contrast to that of neat PLA. The crystallization kinetics was then analyzed by the Avrami, Jezioney, Ozawa, Mo, Kissinger and Lauritzen–Hoffman kinetic models. It can be concluded that at the low heating rate, the cold crystallization of both the neat PLA and nanocomposites proceeds by regime III kinetics. The nucleation effect of clay promote the crystallization to some extent, while the impeding effect of clay results in the decrease of crystallization rate with increasing of clay loadings. At the high heating rate of 10 °C/min, crystallization proceeds mainly by regime II kinetics. Thus, the formation of much more incomplete crystals in the PLACNs with high clay loadings due to the dominant multiple nucleations mechanism in regime II, may have primary contribution to the lower crystallization kinetics, also as a result to the higher degree of crystallinity and lower melting point in contrast to that of neat PLA. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1100–1113, 2007     

Melting behaviors,crystallization kinetics,and spherulitic morphologies of poly(butylene succinate) and its copolyester modified with rosin maleopimaric acid anhydride

This article investigated the melting behaviors, crystallization kinetics, and spherulitic morphologies of poly(butylene succinate) (PBS) and its copolyester (PBSR) modified with rosin maleopimaric acid anhydride, using wide‐angle X‐ray diffraction, differential scanning calorimeter (DSC), and polarized optical microscope. Subsequent DSC scans of isothermally crystallized PBS and PBSR exhibited two melting endotherms, respectively, which was due to the melt‐recrystallization process occurring during the DSC scans. The equilibrium melting point of PBSR (125.9 °C) was lower than that of PBS (139 °C). The commonly used Avrami equation was used to describe the isothermal crystallization kinetics. For nonisothermal crystallization studies, the model combining Avrami equation and Ozawa equation was employed. The result showed a consistent trend in the crystallization process. The crystallization rate was decreased, the perfection of crystals was decreased, the recrystallization was reduced, and the spherulitic morphologies were changed when the huge hydrogenated phenanthrene ring was added into the chain of PBS. The activation energy (ΔE) for the isothermal crystallization process determined by Arrhenius method was 255.9 kJ/mol for PBS and 345.7 kJ/mol for PBSR. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 900–913, 2006     

Preparation and nonisothermal crystallization behavior of polyamide 6/montmorillonite nanocomposites

Polyamide 6 (PA6)/montmorillonite (MMT) nanocomposites were prepared via melt intercalation. The structure, mechanical properties, and nonisothermal crystallization kinetics of PA6/MMT nanocomposites were investigated by X‐ray diffraction (XRD), tensile and impact tests, and differential scanning calorimetry (DSC). Before melt compounding, MMT was treated with an organic surfactant agent. XRD traces showed that PA6 crystallizes exclusively in γ‐crystalline structure within the nanocomposites. Tensile measurements showed that the MMT additions are beneficial in improving the strength and the stiffness of PA6, at the expense of tensile ductility. Impact tests revealed that the impact strength of PA6/MMT nanocomposites tended to decrease with increasing MMT content. The nonisothermal crystallization DSC data were analyzed by Avrami, Ozawa, modified Avrami‐Ozawa, and Nedkov methods. The validity of these empirical equations on the nonisothermal crystallization process of PA6/MMT nanocomposites is discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2878–2891, 2004     

Reflection–absorption infrared spectroscopy investigation of the crystallization kinetics of poly(ethylene terephthalate) ultrathin films

Reflection–absorption infrared spectroscopy was used to study the crystallization behavior of poly(ethylene terephthalate) (PET) ultrathin films. The crystallinity of ultrathin films was estimated by the fraction of trans conformers of PET. The isothermal and nonisothermal crystallization kinetics of ultrathin films with different thicknesses were investigated. The thinner PET film showed slower kinetics during isothermal crystallization than the thicker film. Moreover, the final crystallinity of films with various thicknesses were reduced with decreasing thickness. An Avrami equation was used to fit the acquired results. The Avrami exponents decreased with the film thickness. As for the nonisothermal crystallization, the cold‐crystallization starting temperature shifted to a lower temperature as the film thickness increased. The influence of the substrate on the crystallization kinetics of the films was also studied. The half‐crystallization times and final crystallinities of ultrathin films adsorbed onto a self‐assembled‐monolayer‐treated surface and an untreated substrate were clearly different, although their thickness dependence was similar. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4440–4447, 2004     

Crystallization kinetics and melting behavior of metallocene short‐chain branched polyethylene fractions

Metallocene polyethylene (mPE) fractions are recognized as being more homogeneous with respect to short‐chain branch (SCB) distribution as compared with unfractionated mPEs. Differential scanning calorimetry and polarized optical microscopy (POM) were used to study the influences of SCB content on the crystallization kinetics, melting behavior, and crystal morphology of four butyl‐branched mPE fractions. The parent mPE of the studied fractions was also investigated for comparative purposes. mPE fractions showed a much simpler crystallization behavior as compared with their parent mPE during the cooling experiments. The Ozawa equation was successfully used to analyze the nonisothermal crystallization kinetics of the fractions. The Ozawa exponent n decreased from about 3.5 to 2 as the temperature declined for each fraction, indicating the crystal‐growth geometry changed from three‐dimensional to two‐dimensional. For isothermal crystallization, the fraction with a lesser SCB content exhibited a higher crystallization temperature (T_c) window. The results from the Avrami equation analysis showed the exponent n values were around 3 (with minor variation), which implied that the crystal‐growth geometry is pseudo‐three‐dimensional. Both of the activation energies for nonisothermal and isothermal crystallization were determined for each fraction with Kissinger and Arrhenius‐type equations, respectively. Double melting peaks were observed for both nonisothermally or isothermally crystallized specimens. The high‐melting peak was confirmed induced via the annealing effect during heating scans. The Hoffman–Weeks plot was inapplicable in obtaining the equilibrium melting temperature (T_m°) for each fraction. The relationship between T_c and T_m for the fractions is approximately T_m = T_c (°C) + 8.3. The POM results indicated that the crystals of parent or fractions formed under cooling conditions did not exhibit the typical spherulitic morphology as a result of the high SCB content. © 2002 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 325–337, 2002     

Isothermal and nonisothermal crystallization kinetics of poly(propylene terephthalate)

The kinetics of crystallization of poly(propylene terephthalate) (PPT) samples of different molecular weights were studied under both isothermal and nonisothermal conditions. The Avrami and Lauritzen–Hoffmann treatments were applied to evaluate kinetic parameters of PPT isothermal crystallization. It was found that crystallization is faster for low‐molecular‐weight samples. The modified Avrami equation, and the combined Avrami–Ozawa method were found to successfully describe the nonisothermal crystallization process. Also, the analysis of Lauritzen–Hoffmmann was tested and it resulted in values close to those obtained with isothermal crystallization data. The nonisothermal kinetic data were corrected for the effect of the temperature lag and shifted alone with the isothermal kinetic data to obtain a single master curve, according to the method of Chan and Isayev, testifying to the consistency between the isothermal and corrected nonisothermal data. A new method for ranking of polymers, referring to the crystallization rates, was also introduced. This involved a new index that combines the maximum crystallization rate observed during cooling with the average crystallization rates over the temperature range of the crystallization peak. Furthermore, the effective energy barrier of the dynamic process was evaluated with the isoconversional methods of Flynn and Friedmann. It was found that the energy barrier is lower for the low‐molecular‐weight PPT. The effect of the catalyst remnants on the crystallization kinetics was also investigated and it was found that this is significant only for low‐molecular‐weight samples. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3775–3796, 2004     

Isothermal and nonisothermal crystallization kinetics of novel biobased poly(ethylene succinate-<Emphasis Type="Italic">co</Emphasis>-ethylene sebacate) copolymers from the amorphous state

In this work, the isothermal and nonisothermal crystallization kinetics of three novel biobased poly(ethylene succinate-co-ethylene sebacate) (PESSe) copolymers was systematically investigated with differential scanning calorimetry under different crystallization conditions from the amorphous state. For the isothermal cold crystallization kinetics study, the Avrami equation could well describe the crystallization process of PESSe at various crystallization temperatures. All three PESSe copolymers crystallized through the same crystallization mechanism; moreover, the overall isothermal cold crystallization rate of PESSe decreased with increasing ethylene sebacate (ESe) comonomer content. The nonisothermal cold crystallization kinetics of PESSe was also studied at different heating rates. With increasing ESe content or heating rate, the nonisothermal cold crystallization exotherm of PESSe copolymers shifted to high temperature range. Both the crystallization rate parameter and crystallization rate coefficient of PESSe copolymers decreased with increasing ESe content, indicating that PESSe copolymer with higher ESe content crystallized more slowly than that with lower ESe content. The Ozawa equation was used to analyze the nonisothermal cold crystallization kinetics of PESSe copolymers, which was found to fit the crystallization process very well.     

Influence of ionic association on the nonisothermal crystallization kinetics of sodium sulfonate poly(butylene succinate) ionomers

We evaluated the relationship between the ionic substituents and nonisothermal crystallization behavior in poly(butylene succinate) (PBS) ionomers, synthesized by the introduction of sulfonated dimethyl fumarate (SDMF) with sodium sulfonate. In addition, we investigated the effect of sodium ions on the molecular structure of the PBS backbone by solid‐state ²³Na NMR analysis. Sodium ion aggregates (multiplets) was predominately created with the ionic group concentration, and melt rheology and dynamic melt analysis results showed that multiplet formation induced not only remarkable heterogeneity, but also a high degree of clustering in the PBS chains. At low ionic group concentration, well dispersed multiplets behaved as effective nuclei during the crystallization of the PBS ionomer and accelerated the rate of crystallization. As ionic group concentration grew higher, crystallization rates decreased due to hindered chain mobility by clusters consisting of numerous multiplets. A combined Ozawa and Avrami equation proved to be more effective than the Ozawa equation in describing the nonisothermal crystallization kinetics of PBS and its ionomers. The observed nucleation activity indicates that the nonisothermal crystallization rate is not directly proportional to the ionic group concentration. Superior nucleation activity was observed in PBS ionomer containing 1 mol % SDMF. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 925–937, 2008     

Synthesis and comparative study of biodegradable poly(alkylene sebacate)s

Novel biodegradable polyesters, such as poly(ethylene sebacate) (PESeb), poly(propylene sebacate) (PPSeb), and poly(butylene sebacate) (PBSeb), were synthesized and studied with respect to melting behavior, crystallization kinetics, and enzymatic hydrolysis. PESeb and PPSeb showed multiple melting behavior. Wide angle X‐ray diffractometry measurements at various temperatures, standard, step‐scan, and high‐rate differential scanning calorimetry methods were applied to elucidate the appearance of multiple endotherms in heating scans, which was interpreted in the context of partial melting‐recrystallization and final melting. PBSeb did not show any multiple melting behavior but only a weak tendency for recrystallization on heating. The melting temperatures of PESeb, PPSeb, and PBSeb were measured equal to 78, 57, and 71 °C, respectively. The equilibrium melting points were estimated to be T_m° = 90.2, 69.9, and 77.4 °C for PESeb, PPSeb, and PBSeb, while the corresponding enthalpy of fusion values were found to be ΔH_f = 170 ± 10, 140 ± 10, and 155 ± 10 J/g, respectively. The polyesters showed fast crystallization rates under both isothermal and nonisothermal conditions. Crystallization kinetics was thoroughly investigated using macrokinetic models and isoconversional analysis. Enzymatic hydrolysis rate in the presence of lipases Rhizopus delemar and Pseudomonas cepacia was found to be fast for PPSeb, whereas PESeb and PBSeb showed slow rates and comparable with those of PCL. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 672–686, 2010     

Poly(p‐phenylene sulfide) nonisothermal cold‐crystallization

The poly(p‐phenylene sulfide) (PPS) nonisothermal cold‐crystallization behavior was investigated in a wide heating rate range. The techniques employed were the usual Differential Scanning Calorimetry (DSC), and the less conventional FT‐IR spectroscopy and Energy Dispersive X‐ray Diffraction (EDXD). The low heating rates (Φ) explored by EDXD (0.1 K min^?1) and FT‐IR (0.5–10 K min^?1) are contiguous and complementary to the DSC ones (5–30 K min^?1). The crystallization temperature changes from 95 °C at Φ = 0.05 K min^?1 to 130 °C at Φ = 30 K min^?1. In such a wide temperature range the Kissinger model failed. The model is based on an Arrhenius temperature dependence of the crystallization rate and is widely employed to evaluate the activation energy of the crystallization process. The experimental results were satisfactorily fit by replacing in the Kissinger model the Arrhenius equation with the Vogel–Fulcher–Tamann function and fixing U* = 6.28 k J mol^?1, the activation energy needed for the chains movements, according to Hoffmann. The temperature at which the polymer chains are motionless (T_∞ = 42 °C) was found by fitting the experimental data. It appears to be reasonable in the light of our previously reported isothermal crystallization results, which indicated T_∞ = 48 °C. Moreover, at the lower heating rate, mostly explored by FT‐IR, a secondary stepwise crystallization process was well evidenced. In first approximation, it contributes to about 17% of the crystallinity reached by the sample. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2725–2736, 2005     

Nonisothermal crystallization kinetics of in situ nylon 6/graphene composites by differential scanning calorimetry

The nonisothermal crystallization kinetics was investigated by differential scanning calorimetry for the nylon 6/graphene composites prepared by in situ polymerization. The Avrami theory modified by Jeziorny, Ozawa equation, and Mo equation was used to describe the nonisothermal crystallization kinetics. The analysis based on the Avrami theory modified by Jeziorny shows that, at lower cooling rates (at 5, 10, and 20 K/min), the nylon 6/graphene composites have lower crystallization rate than pure nylon 6. However, at higher cooling rates (at 40 K/min), the nylon 6/graphene composites have higher crystallization rate than pure nylon 6. The values of Avrami exponent m and the cooling crystallization function F(T) from Ozawa plots indicate that the mode of the nucleation and growth at initial stage of the nonisothermal crystallization may be as follows: two‐dimensional (2D), then one‐dimensional (1D) for all samples at 5–10 °C/min; three‐dimensional (3D) or complicated than 3D, then 2D and 1D at 10–20 and 20–40 °C/min. The good linearity of the Mo plots indicated that the combined approach could successfully describe the crystallization processes of the nylon 6 and nylon 6/graphene composites. The activation energies (ΔE) of the nylon 6/graphene composites, determined by Kissinger method, were lower than those of pure nylon 6. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1381–1388, 2011     

Nonisothermal crystallization and melting behavior of poly(β‐hydroxybutyrate)–Poly(vinyl‐acetate) blends

Nonisothermal crystallization and melting behavior of poly(β‐hydroxybutyrate) (PHB)–poly(vinyl acetate) (PVAc) blends from the melt were investigated by differential scanning calorimetry using various cooling rates. The results show that crystallization of PHB from the melt in the PHB–PVAc blends depends greatly upon cooling rates and blend compositions. For a given composition, the crystallization process begins at higher temperatures when slower scanning rates are used. At a given cooling rate, the presence of PVAc reduces the overall PHB crystallization rate. The Avrami analysis modified by Jeziorny and a new method were used to describe the nonisothermal crystallization process of PHB–PVAc blends very well. The double‐melting phenomenon is found to be caused by crystallization during heating in DSC. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 443–450, 1999     

Nonisothermal crystallization behavior of poly(m‐xylene adipamide)/montmorillonite nanocomposites

This article reports the nonisothermal crystallization behavior of MXD6 and its clay nanocomposite system (MXD6/MMT) using differential scanning calorimetry (DSC). The DSC experimental data were analyzed by theoretical modeling of the crystallization kinetics using the Avrami, Ozawa, Jeziorny, and the combined Avrami–Ozawa semiempirical models. It has been determined that these models adequately described the crystallization behavior of the MXD6 nanocomposite at cooling rates below 20 °C/min, but there was a deviation from linear dependence at higher cooling rates. This was attributed to changes of both the free energy and the cooling crystallization function K(T) over the entire crystallization process, as well as possible relaxation effects leading to structural rearrangements. In addition, the activation energy determined using the differential isoconversional method of Friedman was also found to vary, indicating changes in both the free energy and crystallization mechanism. Despite the lack of a reliable theoretical model, the heterogeneous nucleating activity of the MMT nanoparticles was demonstrated and quantified using Dobreva's method (? = 0.71), and the crystallization rate for the nanocomposite system was found to be greater than pure MXD6 by up to 79% at 40 °C/min. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1300–1312, 2009     

Nonisothermal crystallization kinetics of poly(β-hydroxybutyrate)

Kinetics of nonisothermal crystallization of poly(β-hydroxybutyrate) from melt and glassy states were performed by differential scanning calorimetry under various heating and cooling rates. Several different analysis methods were used to describe the process of nonisothermal crystallization. The results showed that both Avrami treatment and a new method developed by combining the Avrami equation and Ozawa equation could describe this system very well. However, Ozawa analysis failed. By using an evaluation method, proposed by Kissinger, activation energies have been evaluated to be 92.6 kJ/mol and 64.6 kJ/mol for crystallization from the glassy and melt state, respectively. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1305–1312, 1998     

Nonisothermal crystallization behavior of the poly(ethylene glycol) block in poly(L‐lactide)–poly(ethylene glycol) diblock copolymers: Effect of the poly(L‐lactide) block length

The confined crystallization behavior, melting behavior, and nonisothermal crystallization kinetics of the poly(ethylene glycol) block (PEG) in poly(L ‐lactide)–poly(ethylene glycol) (PLLA–PEG) diblock copolymers were investigated with wide‐angle X‐ray diffraction and differential scanning calorimetry. The analysis showed that the nonisothermal crystallization behavior changed from fitting the Ozawa equation and the Avrami equation modified by Jeziorny to deviating from them with the molecular weight of the poly(L ‐lactide) (PLLA) block increasing. This resulted from the gradual strengthening of the confined effect, which was imposed by the crystallization of the PLLA block. The nucleation mechanism of the PEG block of PLLA15000–PEG5000 at a larger degree of supercooling was different from that of PLLA2500–PEG5000, PLLA5000–PEG5000, and PEG5000 (the numbers after PEG and PLLA denote the molecular weights of the PEG and PLLA blocks, respectively). They were homogeneous nucleation and heterogeneous nucleation, respectively. The PLLA block bonded chemically with the PEG block and increased the crystallization activation energy, but it provided nucleating sites for the crystallization of the PEG block, and the crystallization rate rose when it was heterogeneous nucleation. The number of melting peaks was three and one for the PEG homopolymer and the PEG block of the diblock copolymers, respectively. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3215–3226, 2006     

Nonisothermal crystallization and melting behavior of syndiotactic polypropylenes of different microstructure

Syndiotactic polypropylenes and their copolymers with 1‐olefins were synthesized using two metallocene/MAO catalytic systems, and the effect of the different microstructures on nonisothermal crystallization and subsequent melting was studied. Using differential scanning calorimetry (DSC) it was observed that samples with lower content of defects showed crystallization on cooling from the melt, and a double melting peak in the subsequent heating scan, the latter associated with melt, recrystallization and remelt processes that it was confirmed by its nonreversing exothermic process found by means of temperature modulated DSC (MDSC). However, polymers with high amount of defects showed cold crystallization on heating followed by a melting process, that it was observed by MDSC. Wide angle X‐ray diffraction was used for characterizing the changes of crystalline forms in relationship with crystallization process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 798–806, 2008