Thiol–enes: Chemistry of the past with promise for the future

The photopolymerization of mixtures of multifunctional thiols and enes is an efficient method for the rapid production of films and thermoset plastics with unprecedented physical and mechanical properties. One of the major obstacles in traditional free‐radical photopolymerization is essentially eliminated in thiol–ene polymerizations because the polymerization occurs in air almost as rapidly as in an inert atmosphere. Virtually any type of ene will participate in a free‐radical polymerization process with a multifunctional thiol. Hence, it is possible to tailor materials with virtually any combination of properties required for a particular application. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5301–5338, 2004     

Kinetics of thiol–ene and thiol–acrylate photopolymerizations with real‐time fourier transform infrared

We used real‐time Fourier transform infrared to monitor the conversion of both thiol and ene (vinyl) functional groups independently during photoinduced thiol–ene photopolymerizations. From these results, the stoichiometry of various thiol–ene and thiol–acrylate polymerizations was determined. For thiol–ene polymerizations, the conversion of ene functional groups was up to 15% greater than the conversion of thiol functional groups. For stoichiometric thiol–acrylate polymerizations, the conversion of the acrylate functional groups was roughly twice that of the thiol functional groups. With kinetic expressions for thiol–acrylate polymerizations, the acrylate propagation kinetic constant was found to be 1.5 times greater than the rate constant for hydrogen abstraction from the thiol. Conversions of thiol–acrylate systems of various initial stoichiometries were successfully predicted with this ratio of propagation and chain‐transfer kinetic constants. Thiol–acrylate systems with different initial stoichiometries exhibited diverse network properties. Thiol–ene systems were initiated with benzophenone and 2,2‐dimethoxy‐2‐phenylacetophenone as initiators and were also polymerized without a photoinitiator. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3311–3319, 2001     

Photocatalyzed thiol–alkene coupling: Mechanistic study and polymer synthesis

Due to the “click” chemistry characteristics of the thiol–ene reaction, these transformations have been gaining an increasing amount of attention in current chemical research. The high efficiency and selectivity of these transformations have been useful for many areas of study, from small molecule organic synthesis, to polymer synthesis and functionalization, to bio‐conjugation reactions. In this work, a study of a novel method of photochemical thiol–ene reactions using alkyl halides and an tris[2‐phenylpyridinato‐C2,N]iridium(III) (Ir(ppy)₃) photocatalyst is investigated. This process is shown to progress rapidly and has the benefit of low catalyst and initiator concentrations relative to reagents as well as mild conditions associated with photochemical processes. To understand the mechanism of this process, catalyst and initiator concentrations and other reaction conditions are varied. To demonstrate the utility of this process, a step‐growth thiol–ene polymer is synthesized using dithiol and diene monomers and a crosslinked polymer network is synthesized as well. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1931–1937     

Thiol‐ene photopolymerization of polymer‐derived ceramic precursors

The liquid, ceramic precursor monomer VL20 was copolymerized with a thiol monomer in a traditional radical thiol‐ene photopolymerization. Polymerization occurred via addition of the thiol functional group to the vinyl silazane functional group in a 1:1 ratio consistent with a step‐growth polymerization. Gelation occurred at a high conversion of functional groups (70%) consistent with an average molecular weight and functionality of 560 and 1.7, respectively, for VL20 monomers. Initiatorless photopolymerization of the thiol‐VL20 system also occurred upon irradiation at either 365 or 254 nm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1752–1757, 2004     

Sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions as a route to well‐defined mono and bis end‐functionalized poly(N‐isopropylacrylamide)

Sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions have been used as a facile and quantitative method for modifying end‐groups on an N‐isopropylacrylamide (NIPAm) homopolymer. A well‐defined precursor of polyNIPAm (PNIPAm) was prepared via reversible addition‐fragmentation chain transfer (RAFT) polymerization in DMF at 70 °C using the 1‐cyano‐1‐methylethyl dithiobenzoate/2,2′‐azobis(2‐methylpropionitrile) chain transfer agent/initiator combination yielding a homopolymer with an absolute molecular weight of 5880 and polydispersity index of 1.18. The dithiobenzoate end‐groups were modified in a one‐pot process via primary amine cleavage followed by phosphine‐mediated nucleophilic thiol‐ene click reactions with either allyl methacrylate or propargyl acrylate yielding ene and yne terminal PNIPAm homopolymers quantitatively. The ene and yne groups were then modified, quantitatively as determined by ¹H NMR spectroscopy, via radical thiol‐ene and radical thiol‐yne reactions with three representative commercially available thiols yielding the mono and bis end functional NIPAm homopolymers. This is the first time such sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions have been used in polymer synthesis/end‐group modification. The lower critical solution temperatures (LCST) were then determined for all PNIPAm homopolymers using a combination of optical measurements and dynamic light scattering. It is shown that the LCST varies depending on the chemical nature of the end‐groups with measured values lying in the range 26–35 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3544–3557, 2009     

Photoinduced thiol–ene crosslinking of globalide/ε‐caprolactone copolymers: Curing performance and resulting thermoset properties

The increasing demand for bioderived polymers led us to investigate the potential use of the macrolactone globalide in thermoset synthesis via the photoinduced thiol–ene reaction. A series of six lipase‐catalyzed poly(globalide‐caprolactone) copolyesters bearing internal main‐chain unsaturations ranging from 10 to 50 and 100 mol % were successfully crosslinked in the melt with equal amounts of thiol groups from trimethylolpropane‐trimercapto propionate affording fully transparent amorphous elastomeric materials with different thermal and viscoelastic properties. Three major conclusions can be drawn from this study: (i) high thiol–ene conversions (>80%) were easily attained for all cases, while maintaining the cure behavior, and irrespective of functionality at reasonable reaction rates; (ii) parallel chain‐growth homopropagation of the ene monomer is insignificant when compared with the main thiol–ene coupling route; and (iii) high ene‐density copolymers result in much lower extracted sol fractions and high T_g values as a result of a more dense and homogeneous crosslinked network. The thiol–ene system evaluated in this contribution serve as model example for the sustainable use of naturally occurring 1,2‐disubstituted alkenes in making semisynthetic polymeric materials in high conversions with a range of properties. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012.     

Thiol–ene coupling reaction of fatty acid monomers

The reactivities and reaction rates of the thiol–ene coupling reaction of 2‐ethyl‐(hydroxymethyl)‐1,3‐propanediol trimercapto acetate and 2‐ethyl‐(hydroxymethyl)‐1,3‐propanediol trimercapto propionate with two common unsaturated fatty acid methyl esters (methyl oleate and methyl linoleate) were evaluated. The reactions were monitored with real‐time IR and ¹H NMR, which both showed that the mercapto acetate was more reactive than the mercapto propionate. Both thiols were more prone to add to the monounsaturated methyl oleate than to methyl linoleate, which contained two unconjugated double bonds. According to bond energy calculations, the thiol hydrogen of mercapto acetate was somewhat more difficult to abstract than the hydrogen of mercapto propionate. Consequently, the formed S? C bond in the acetate case was stronger than in the propionate case, and so the equilibrium was more shifted toward the addition products. The real‐time IR measurements also showed that the cis unsaturation in methyl oleate isomerized much more quickly than that in methyl linoleate, and this also had an impact on the overall addition rate of the thiols because a trans unsaturation was more reactive than a cis unsaturation. The higher isomerization rates in the oleate systems, compared with those of the linoleate systems, was suggested to be due to a more restricted rotation along the C? C bond of the reacted unsaturation in linoleate. This study showed the importance of trans unsaturations in obtaining reasonable reaction rates in thiol–ene reactions with fatty acid derivatives. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6346–6352, 2004     

New photo‐induced thiol‐ene crosslinked films based on linear methacrylate copolymer polythiols

Thiol‐ene radical addition by photolysis is a highly efficient click reaction of sufhydryl groups with reactive enes that has been extensively explored as a promising means to construct multifunctional materials. Here, photo‐induced thiol‐ene crosslinked films composed of linear methacrylate copolymer polythiols (MCPsh) are reported. Well‐defined MCPsh copolymers were prepared by thiol‐responsive cleavage of pendant disulfide linkages positioned in the corresponding methacrylate copolymers with narrow molecular weight distribution which were synthesized by a controlled radical polymerization method. With a commercially available multifunctional acrylate as a model ene, photo‐induced thiol‐ene radical polyaddition of these polythiols is competitive to free‐radical homopolymerization of acrylates, yielding crosslinked films exhibiting rapid cure, uniform network, and enhanced mechanical properties; these properties are required for high performance coating materials. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2860–2868.     

Multifunctional linear methacrylate copolymer polyenes having pendant vinyl groups: Synthesis and photoinduced thiol–ene crosslinking polyaddition

UV‐induced thiol‐ene crosslinked films composed of linear methacrylate copolymers having pendant enes (MCPenes) are reported. An approach involving a combination of controlled radical polymerization to synthesize well‐controlled pendant hydroxyl containing copolymers (MCP_OHs) with the following facile carbodiimide coupling of the formed MCP_OHs with enes allows for the synthesis of well‐controlled MCPenes with narrow molecular weight distribution. The density of the pendant enes in MCPenes are easily modulated by varying monomer ratios in the feed. Under UV irradiation, the resulting MCPenes undergo thiol‐ene polyaddition reactions with polythiols to form crosslinked films with a uniform network. The results from thermal and mechanical analysis suggest these properties are tuned by adjusting the densities of pendant enes in MCPenes and the amount of thiols in the reactive mixtures. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 572–581     

High‐throughput kinetic analysis of acrylate and thiol‐ene photopolymerization using temperature and exposure time gradients

In this work, a high‐throughput technique for evaluating photopolymers is developed to enable simultaneous measurement of the effects of temperature in combination with exposure time. Temperature and exposure time gradients were produced in orthogonal directions on a single sample, and subsequently sampled using Fourier transform infrared (FTIR) spectroscopy. The technique developed here allows for photopolymerization kinetics to be analyzed rapidly over a large range of industrially relevant temperatures, giving insight into the role temperature and the polymer's glass transition temperature have in dictating the photopolymerization kinetics. In the 70/30 wt % hexyl acrylate and hexanediol diacrylate system, conversion in samples below the glass transition temperature (T_G) was 66 ± 2% after 12 s, significantly lower than the 93 ± 4% conversion at 12 s for samples polymerized at temperatures above the T_G. In addition, a thiol‐ene system was analyzed to study the effect of temperature on the ene homopolymerization in allyl ether monomers, which leads to incomplete thiol conversion in stoichiometrically balanced systems. At a 60% thiol conversion, the allyl ether‐ene conversion at all temperatures is 65 ± 3% irrespective of initial formulation temperature, indicative of the homopolymerization behavior being nearly independent of temperature. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1502–1509, 2008     

Photopolymerization of thiol‐ene systems based on oligomeric thiols

Thiol oligomers were copolymerized with a triallyl ether by a photoinduced polymerization process. These oligomeric thiol‐ene systems comprise the same components as a photopolymerized thiol‐ene‐acrylate ternary system, yet the photopolymerized networks have much lower glass transition temperatures. An investigation into the effect of oligomeric thiol design on network formation was conducted by analyzing the reaction kinetics and thermal/mechanical properties of the thiol‐ene networks. Real‐time FTIR analysis shows that total conversion is >90% for all thiols investigated. Photo‐DSC analysis shows that the maximum exotherm rate is roughly equivalent for all of the thiols when the equivalent weight of the thiol is taken into account. As would be expected, the glass transition temperature and tensile strength increase with thiol functionality and lower thiol equivalent weight for thiols with functionality from 2 to 4. Films made using the oligomeric thiols have essentially the same glass transition temperatures and tensile modulus values regardless of thiol design. These results distinguish the method for generation of networks consisting of an initial Michael reaction of thiols and acrylates followed by a photoinitiated copolymerization with a multifunctional ene from the traditional photolysis of the corresponding thiol‐ene‐acrylate ternary systems with no Michael reaction. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 14–24, 2009     

Postfunctionalization of polyoxanorbornene via sequential Michael addition and radical thiol‐ene click reactions

We demonstrated the successful postfunctionalization of poly(oxanorbornene imide) (PONB) with two types of double bonds using sequential orthogonal reactions, nucleophilic thiol‐ene coupling via Michael addition and radical thiol‐ene click reactions. First, the synthesis of PONB with side chain acrylate groups is carried out via ring‐opening metathesis polymerization and nitroxide radical coupling reaction, respectively. Subsequently, the resulting polymer having two different orthogonal functionalities, main chain vinyl and side chain acrylate, is selectively modified via two sequential thiol‐ene click reactions, nucleophilic thiol‐ene coupling via Michael addition and photoinduced radical thiol‐ene. The orthogonal reactivity of two diverse double bonds, vinyl and acrylate functionalities, for the abovementioned consecutive thiol‐ene click reactions was first demonstrated on the model compound. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Modular material system for the microfabrication of biocompatible hydrogels based on thiol–ene‐modified poly(vinyl alcohol)

Novel modifications of the synthetic polymer poly(vinyl alcohol) (PVA) were developed for application in the field of biomedical engineering. PVA was modified with allyl succinic anhydride, norbornene anhydride as well as with γ‐thiobutyrolactone to produce macromers with reactive ene and thiol groups, respectively. Cytotoxicity studies have shown that the material exhibits almost no cell‐toxicity, when used in concentrations of 1 and 0.1 wt % for 24 h. The obtained macromers were photocrosslinked via thiol–ene chemistry. Storage stability of the macromer mixtures with different concentrations of pyrogallol as stabilizer were investigated. Photorheometry was employed to optimize mixtures concerning reactivity based on their thiol‐to‐ene ratio, photoinitiator concentration, and macromer content. The crosslinked hydrogels were studied concerning their swellability. To form hydrogels with cellular structure two‐photon‐polymerization (2PP) was employed. Processing windows for 2PP of selected mixtures were determined. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2060–2070     

An efficient nonisocyanate route to polyurethanes via thiol‐ene self‐addition

A novel and efficient strategy for the synthesis of nonisocyanate polyurethanes has been developed via thiol–ene self‐photopolymerization. An aliphatic thiol–ene carbamate monomer (allyl(2‐mercaptoethyl)carbamate, AMC) was synthesized by a one‐step synthesis procedure, from cysteamine and allyl chloroformate. The urethane group was therefore incorporated directly into the monomer precursor, avoiding the problems associated to toxic isocyanates. AMC was successfully stabilized with the radical inhibitor pyrogallol (1% wt). In addition, the use of phenyl phosphonic acid as coadditive allowed its stabilization for lower concentrations of pyrogallol (0.1% wt). AMC was directly transformed into thermoplastic polyurethane (TPU) through thiol–ene photopolymerization by UV‐irradiation at 365 nm. The obtained TPU presented semi‐crystalline nature and very high thermal stability (T_5% ～325 °C). It was found that high concentrations of pyrogallol decreased the reaction rate and final conversion of photopolymerization. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3017–3025     

The power of thiol‐ene chemistry

As a tribute to Professor Charlie Hoyle, we take the opportunity to review the impact of thiol‐ene chemistry on polymer and materials science over the past 5 years. During this time, a renaissance in thiol‐ene chemistry has occurred with recent progress demonstrating its unique advantages when compared with traditional coupling and functionalization strategies. Additionally, the robust nature of thiol‐ene chemistry allows for the preparation of well‐defined materials with few structural limitations and synthetic requirements. To illustrate these features, the utility of thiol‐ene reactions for network formation, polymer functionalization, dendrimer synthesis, and the decoration of three‐dimensional objects is discussed. Also, the development of the closely related thiol‐yne chemistry is described. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 743–750, 2010     

Photopolymerization behavior in nanocomposites formed with thiol–acrylate and polymerizable organoclays

Because of the inherent characteristics of the thiol–ene step growth mechanism in preparation of thiol–ene photopolymer clay nanocomposites, the ratio between thiol and ene functional groups at and near the organoclay surfaces may have a significant effect on the polymerization behavior. This study investigates the influence of monomer composition and the type of polymerizable organoclay on thiol–acrylate photopolymerization behavior in preparation of photocurable clay nanocomposite systems. To this end, two types of polymerizable organoclays with acrylate or thiol functional group on the clay surfaces were compared in monomer compositions with different polarity and functionality. Real‐time infrared spectroscopy was used to characterize polymerization behavior in conjunction with photo‐DSC. The degree of clay exfoliation was evaluated using small angle X‐ray scattering and correlated with photopolymerization behavior. Higher chemical compatibility of components induced enhanced clay exfoliation resulting in increase in photopolymerization rate. By affecting the stoichiometric ratio of functional groups in the clay gallery, thiolated organoclays enhance thiol–ene reaction, whereas acrylated organoclays encourage acrylate homopolymerization. In addition, inducing more propagating thiyl radicals on the organoclay surfaces by increasing functionality of thiol monomer also facilitates thiol–ene copolymerization, whereas the increase of acrylate functionality reduces final thiol conversion. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Functional off‐stoichiometry thiol‐ene‐epoxy thermosets featuring temporally controlled curing stages via an UV/UV dual cure process

We present a facile two‐stage UV/UV activation method for the polymerization of off‐stoichiometry thiol‐ene‐epoxy, OSTE+, networks. We show that the handling and processing of these epoxy‐based resins is made easier by introducing a material with a controlled curing technique based on two steps, where the first step offers excellent processing capabilities, and the second step yields a polymer with suitable end‐properties. We investigate the sequential thiol‐ene and thiol‐epoxy reactions during these steps by studying the mechanical properties, functional group conversion, water absorption, hydrolytic stability, and thermal stability in several different thiol‐ene‐epoxy formulations. Finally, we conclude that the curing stages can be separated for up to 24 h, which is promising for the usefulness of this technique in industrial applications. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2604‐2615     

Silicon‐based mercaptans: High‐performance monomers for thiol‐ene photopolymerization

Ester‐free silane and siloxane‐based thiol monomers were successfully synthesized and evaluated for application in thiol‐ene resins. Polymerization reaction rates, conversion, network properties as well as degradation experiments of those thiol monomers in combination with triallyl‐1,3,5‐triazine‐2,4,6(1H,3H,5H)‐trione (TATT) as ene component were performed and compared with formulations containing the commercially available mercaptopropionic ester‐based thiol pentaerythritol tetra‐3‐mercaptopropionate. Kinetic analysis revealed appropriate reaction rates and conversions reaching 90% and higher. Importantly, storage stability tests of those formulations clearly indicate the superiority of the synthesized mercaptans compared with pentaerythritol tetra‐3‐mercaptopropionate/TATT resins. Moreover, photocured samples containing silane‐based mercaptans provide higher glass transition temperatures and withstand water storage without a significant loss in their network properties. This behavior together with the observed excellent degradation resistance of photocured silane‐based thiol/TATT formulations make these multifunctional mercaptans interesting candidates for high‐performance applications, such as dental restoratives and automotive resins. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 418–424     

Synthesis and functionalization of dendron‐polymer conjugate based hydrogels via sequential thiol‐ene “click” reactions

Fabrication and functionalization of hydrogels from well‐defined dendron‐polymer‐dendron conjugates is accomplished using sequential radical thiol‐ene “click” reactions. The dendron‐polymer conjugates were synthesized using an azide‐alkyne “click” reaction of alkene‐containing polyester dendrons bearing an alkyne group at their focal point with linear poly(ethylene glycol)‐bisazides. Thiol‐ene “click” reaction was used for crosslinking these alkene functionalized dendron‐polymer conjugates using a tetrathiol‐based crosslinker to provide clear and transparent hydrogels. Hydrogels with residual alkene groups at crosslinking sites were obtained by tuning the alkene‐thiol stoichiometry. The residual alkene groups allow efficient postfunctionalization of these hydrogel matrices with thiol‐containing molecules via a subsequent radical thiol‐ene reaction. The photochemical nature of radical thiol‐ene reaction was exploited to fabricate micropatterned hydrogels. Tunability of functionalization of these hydrogels, by varying dendron generation and polymer chain length was demonstrated by conjugation of a thiol‐containing fluorescent dye. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 926–934