Spatial and temporal thermal analysis of acousto-optic deflectors using finite element analysis model

Thermal effects greatly influence the optical properties of the acousto-optic deflectors (AODs). Thermal analysis plays an important role in modern AOD design. However, the lack of an effective method of analysis limits the prediction in the thermal performance. In this paper, we propose a finite element analysis model to analyze the thermal effects of a TeO₂-based AOD. Both transducer heating and acoustic absorption are considered as thermal sources. The anisotropy of sound propagation is taken into account for determining the acoustic absorption. Based on this model, a transient thermal analysis is employed using ANSYS software. The spatial temperature distributions in the crystal and the temperature changes over time are acquired. The simulation results are validated by experimental results. The effect of heat source and heat convection on temperature distribution is discussed. This numerical model and analytical method of thermal analysis would be helpful in the thermal design and practical applications of AODs.     

Electronic tuning of acoustic resonances in acousto-optic mode lockers

The effect of electronic tuning of acoustic resonances in an acousto-optic mode locker is studied theoretically and experimentally. The tuning is implemented by means of changing a matching inductance connected to the transducer in parallel. Experimental investigations are carried out with a mode locker made of a fused quartz with a lithium niobate transducer. Varying magnitude of the inductor from 0.025 to 0.25 mH has made it possible to retune the acoustic resonance frequency by 0.19 MHz, i.e. wider than the acoustic resonance half-width.     

自聚焦换能器的声场研究

高强度聚焦超声（HIFU）治疗局部肿瘤是一项无创伤的新技术,有着很好的应用前景,因此对其声场的研究是有实际的价值的。对声场的研究不仅有利于换能器的设计,提高治疗的效果;而且有助声场测量方案的设计,提高对治疗超声剂量的安全保证。本文采用时域有限差分法研究了自聚焦换能器的声场,分别对简谐波,脉冲波进行了研究。比较清楚地看出在焦区的声场可以认为是平面波,这对光纤端面法声场测量提供了有力的支持。     

Impact of thermal effects induced by ultrasound on viability of rat C6 glioma cells

In order to have consistent and repeatable effects of sonodynamic therapy (SDT) on various cancer cells or tissue lesions we should be able to control a delivered ultrasound energy and thermal effects induced. The objective of this study was to investigate viability of rat C6 glioma cells in vitro depending on the intensity of ultrasound in the region of cells and to determine the exposure time inducing temperature rise above 43 °C, which is known to be toxic for cells. For measurements a planar piezoelectric transducer with a diameter of 20 mm and a resonance frequency of 1.06 MHz was used. The transducer generated tone bursts with 94 μs duration, 0.4 duty-cycle and initial intensity I_SATA (spatial averaged, temporal averaged) varied from 0.33 W/cm² to 8 W/cm² (average acoustic power varied from 1 W to 24 W). The rat C6 glioma cells were cultured on a bottom of wells in 12-well plates, incubated for 24 h and then exposed to ultrasound with measured acoustic properties, inducing or causing no thermal effects leading to cell death. Cell viability rate was determined by MTT assay (a standard colorimetric assay for assessing cell viability) as the ratio of the optical densities of the group treated by ultrasound to the control group. Structural cellular changes and apoptosis estimation were observed under a microscope. Quantitative analysis of the obtained results allowed to determine the maximal exposure time that does not lead to the thermal effects above 43 °C in the region of cells for each initial intensity of the tone bursts used as well as the threshold intensity causing cell death after 3 min exposure to ultrasound due to thermal effects. The averaged threshold intensity was found to be about 5.7 W/cm².     

一种纵扭复合换能器型超声马达的原理及实验研究

本文从纵扭振动换能器理论出发，计算了一种新的复合换能器型超声马达，并进行了实验研究，测出了其主要性能参数。     

柔性超声换能器在生物医学中的研究进展*

传统超声换能器存在体积大、表面刚性的缺点,无法用于人体复杂皮肤表面和可穿戴器件的设计。为使换能器具有灵活、体积小,满足可穿戴的特点,将其压电元件、电极和封装等各组成部分重组为柔性换能器。相比于传统换能器,它有两个优点：首先,不需要专业人员操作,可实现持续性的超声监控或治疗。其次,通过更全面的皮肤表面覆盖,扩大声场范围。在超声诊断方面,改善声信号采集,获得更全面的检测信息;在超声治疗方面,增加声能量沉积,提高疗效。柔性换能器使超声医疗应用场景多元化,可实现连续超声诊断或超声治疗。该文首先概述了其在设计和加工方面的最新进展,然后重点介绍了其在诊断和治疗方面的应用,最后讨论了这一领域所面临的挑战并对发展前景进行展望。     

Thermal effects of photonic-bandgap fiber laser

A steady thermal model of photonic-bandgap fiber laser (PBFL) is presented. Temperature distribution in PBFL is analyzed by heat transfer equations and numerical finite-element method (FEM) separately. Thermal stress distribution caused by the temperature difference between the inner and outer claddings is calculated. The results show that the thermal stresses in this fiber structure are low less than the critical tensile stress in fused silica.     

Thermal effects in high-power Nd:YAG disk-type solid state laser

An investigation of thermal effects in a high-power Nd:YAG disk-type solid state laser pumped with different pump beam transverse profiles is carried out by numerical simulation based on the finite element method (FEM). Impact of the heat sink on the thermal effects is included in the simulation. The distribution of first principle stress, thermally induced birefringence, including the distribution and variation of the birefringence loss, are studied. The characteristics of the phase variation are analyzed with consideration of the temperature gradient, deformation, strain and thermal stress. Thermal lensing is explored as a function of pump power and of the radius pumped with different pump beam transverse profiles. The non-parabolic part of optical phase distortion is simulated. Furthermore, the characteristics of the bi-focus of the disk laser are also studied. Experiments on the maximum tensile stress distribution and depolarization loss are carried out. The presented calculations are in qualitative agreement with the experimental observations.     

同时发射和接收纵波和横波的压电复合材料换能器

通过控制压电复合材料中压电相的分布形式，本文具有在百度模振动的１－３型压电复合材料和具有扭转模振动的拼接２－２型压电复合材料组合在一起，构成一种混俣模式压电材料，并测试了这种压电材料晶片的性能参数，使用这种晶片作的换能器可以根据使用者的要求，单独产生纵波或横波，也可同时产生这两种波。     

高功率厘米波辐照黄粉虫幼虫和草坪热效应研究

 建立了高功率厘米波辐照平台,测定了黄粉虫幼虫和草坪的表面温升及黄粉虫幼虫致死百分率。实验结果表明,高功率厘米波辐照过程中黄粉虫幼虫温度与辐照时间呈一定函数关系;草坪温度与辐照时间也呈一定函数关系,但两者不同。由实验结果拟合得到了辐照过程中黄粉虫幼虫表面温升与辐照时间之间的关系和黄粉虫幼虫致死百分率与辐照时间及致死百分率与温度的函数关系。实验观察了不同时间厘米波辐照对草坪的影响。观察结果表明温度超过一定数值时,厘米波辐照将损伤草坪。采用图像处理方法得到了草坪损伤的量化结果,并进一步得到了草坪损伤程度与辐照温度的函数关系。     

A novel technique for predicting ionizing radiation effects of commercial MOS devices

A nondestructive selection technique for predicting ionizing radiation effects of commercial metal-oxide-semiconductor (MOS) devices has been put forward. The basic principle and application details of this technique have been discussed. Practical application for the 54HC04 and 54HC08 circuits has shown that the predicted radiation-sensitive parameters such as threshold voltage, static power supply current and radiation failure total dose are consistent with the experimental results obtained only by measuring original electrical parameters. It is important and necessary to choose suitable information parameters. This novel technique can be used for initial radiation selection of some commercial MOS devices.     

Thermal dissipation effects of the entangled photon generated by a nonlinear ring resonator

We firstly analyze the thermal dissipation effects of the entangled photons generated by a nonlinear optical ring resonator. To obtain the corresponding equation of motion of the entangled photons generated by a four-wave mixing process within the system, we propose the Markov approximation to repel the reservoir operators. The system master equation in the interaction picture for both degenerate and non-degenerate cases is analyzed and obtained. The established system can be used to characterize the optimum entangled photons in some cases where the thermal dissipation effects may introduce noise into the system. In this work, the entangled photons can be generated into two forms, firstly, the two entangled photon states are generated and, the other, the four entangled photon states, can be easily obtained. Results obtained have shown that the optimum entangled photon in terms of entangled photon visibility can be compensated (i.e. unchanged) under thermal dissipation effects.     

Dual effects of ultrasound on fabrication of anodic aluminum oxide

Ultrasound has been proven to enhance the mass transfer process and impact the fabrication of anodic aluminum oxide (AAO). However, the different effects of ultrasound propagating in different media make the specific target and process of ultrasound in AAO remain unclear, and the effects of ultrasound on AAO reported in previous studies are contradictory. These uncertainties have greatly limited the application of ultrasonic-assisted anodization (UAA) in practice. In this study, the bubble desorption and mass transfer enhancement effects were decoupled based on an anodizing system with focused ultrasound, such that the dual effects of ultrasound on different targets were distinguished. The results showed that ultrasound has the dual effects on AAO fabrication. Specifically, ultrasound focused on the anode has a nanopore-expansion effect on AAO, leading to a 12.24 % improvement in fabrication efficiency. This was attributed to the promotion of interfacial ion migration through ultrasonic-induced high-frequency vibrational bubble desorption. However, AAO nanopores were observed to shrink when ultrasound was focused on the electrolyte, accompanied by a 25.85 % reduction in fabrication efficiency. The effects of ultrasound on mass transfer through jet cavitation appeared to be the reason for this phenomenon. This study resolved the paradoxical phenomena of UAA in previous studies and is expected to guide AAO application in electrochemistry and surface treatments.     

Solvent effects on the S0→S2 absorption spectra of β-carotene

Absorption spectra of β-carotene in 31 solvents are measured in ambient conditions. Solvent effects on the 0-0 band energy, the bandwidth, and the transition moment of the S 0 → S 2 transition are analysed. The discrepancies between published results of the solvent effects on the 0-0 band energy are explained by taking into account microscopic solute-solvent interactions. The contributions of polarity and polarizability of solvents to 0-0 band energy and bandwidth are quantitatively distinguished. The 0-0 transition energy of the S 2 state at the gas phase is predicted to locate between 23000 and 23600 cm-1 .     

Thermal hysteresis and memory effects in TIInS2

The dielectric susceptibility of layered TlInS₂ was studied in the temperature range of successive phase transitions. Thermal hysteresis was observed in the incommensurate phase. It was shown that after annealing the crystal at a fixed temperature within the incommensurate phase, the existing temperature interval of this phase reveals noticeable broadening. The thermal memory effect is discussed using a defect density wave model.     

极化子效应对量子盘中线性和非线性光吸收系数的影响

利用密度矩阵的方法,得出了考虑极化子效应的量子盘的线性和非线性光吸收系数的解析表达式,并以GaAs为例讨论了光吸收系数与不同的入射光子能量和量子盘的厚度之间的关系.结果表明,极化子效应对吸收系数有相当的影响 关键词： 量子盘 光学吸收系数 极化子效应     

Rapid Ag/Sn/Ag transient liquid phase bonding for high-temperature power devices packaging by the assistance of ultrasound

Rapid transient liquid phase (TLP) bonding process on Ag/Sn/Ag system is achieved in air by the assistance of ultrasonic, which has great potential to be applied to high-temperature power devices packaging. In this study, the influence of ultrasonic effect on the morphology and growth kinetics of Ag₃Sn grains, and the joint microstructure, mechanical property and thermal reliability were systematically investigated. Experimental results indicated that the rapid consumption of the “dynamic” transient liquid phase was attributed to the accelerated dissolution of Ag substrate and the extrusion of liquid Sn, which were entirely induced by the complex sonochemical effects on the liquid/solid intermetallic compounds (IMCs) interface. An elongated scallop-like morphology of Ag₃Sn grains was developed during Ag/Sn interfacial reaction with ultrasonic, accompanied by widening of grooves between neighbored grains. This phenomenon is called as a strengthening thermal grooving, in which the grooves at grain boundaries provide stable molten channels for Ag atoms diffusion from the substrate. Consequently, the improved elemental diffusion was evaluated through the growth kinetics of Ag₃Sn IMCs, with conservative estimation of 6–16.5 times faster than the traditional TLP process. In addition, both excellent mechanical property and thermal reliability of the Ag-Sn intermetallic joint were experimentally verified by shear test and high-temperature storage test, respectively.     

A simple model of ultrasound propagation in a cavitating liquid. Part II: Primary Bjerknes force and bubble structures

In a companion paper, a reduced model for propagation of acoustic waves in a cloud of inertial cavitation bubbles was proposed. The wave attenuation was calculated directly from the energy dissipated by a single bubble, the latter being estimated directly from the fully nonlinear radial dynamics. The use of this model in a mono-dimensional configuration has shown that the attenuation near the vibrating emitter was much higher than predictions obtained from linear theory, and that this strong attenuation creates a large traveling wave contribution, even for closed domain where standing waves are normally expected. In this paper, we show that, owing to the appearance of traveling waves, the primary Bjerknes force near the emitter becomes very large and tends to expel the bubbles up to a stagnation point. Two-dimensional axi-symmetric computations of the acoustic field created by a large area immersed sonotrode are also performed, and the paths of the bubbles in the resulting Bjerknes force field are sketched. Cone bubble structures are recovered and compare reasonably well to reported experimental results. The underlying mechanisms yielding such structures is examined, and it is found that the conical structure is generic and results from the appearance a sound velocity gradient along the transducer area. Finally, a more complex system, similar to an ultrasonic bath, in which the sound field results from the flexural vibrations of a thin plate, is also simulated. The calculated bubble paths reveal the appearance of other commonly observed structures in such configurations, such as streamers and flare structures.     

Diffraction losses of Nd:YAG and Yb:YAG laser crystals

Based on space-dependent rate equations, the lowest threshold input power for a diode end-pumped solid-state laser is obtained for the pump spot size w_p→0. However, as the pump beam waist is decreased, the thermally induced effects in the laser rod would be very high. Diffraction losses caused by radial and tangential variations of refractive index have been analyzed and compared for the Nd : YAG and the Yb : YAG at room temperature (300 K) and liquid-nitrogen temperature (77 K).     

Properties and characteristics of P(VDF/TrFE) transducers manufactured by a solution casting method for use in the MHz-range ultrasound in air

Highly effective piezoelectric polymer transducers operating in air at high frequencies have been successfully made by casting a solution of ferroelectric poly(vinylidene fluoride-co-trifluoroethylene) P(VDF/TrFE) directly on a backing metal plate, and their performance has been evaluated. By utilizing this method, it has been possible to develop the three kinds of transducers that operate respectively at 4, 6 and 10 MHz in air. For precise evaluation of the performance of the P(VDF/TrFE) transducers, the absorption loss in air was measured up to 10 MHz. It was confirmed that the empirical formula obtained from the measured absorption values in air at high frequencies was in alignment with its theoretical value. In addition, a high lateral resolution acoustic image of a ROM-Chip (amplitude-image) at 6 MHz in air was successfully displayed using an air coupled concave type P(VDF/TrFE) transducer by bonding an epoxy adhesive.