Quantitation of the antitumour agent N-[2-(dimethylamino)ethyl]acridine-4-carboxamide in plasma by high-performance liquid chromatography

N-[2-(Dimethylamino)ethyl]acridine-4-carboxamide is a new experimental antitumour agent which has excellent in vivo activity against the Lewis lung tumour in mice. A reversed-phase high-performance liquid chromatographic method is described for the measurement of this agent in plasma. The internal standard was N-[2-(diethylamino)ethyl]acridine-4-carboxamide. The compounds of interest were extracted from plasma (0.2 ml) with acetonitrile and further purified on C18 solid-phase extraction Bond Elut columns. After elution with acetonitrile-ammonium acetate buffer and evaporation, the final separation was carried out on a C18 muBondapak column with fluorimetric detection. Over the plasma concentration range 100-5000 nM, the intra- and inter-assay coefficients of variation were less than 4.1 and 7.7%, respectively. The accuracy of the method varied from 97 to 105% of the theoretical values. The lowest concentration which could be measured with acceptable accuracy (+/- 10%) and precision (coefficient of variation less than 10%) was 10 nM. The method was sufficiently sensitive to allow pharmacokinetic analyses of 30 mumol/kg doses for more than six half-lives (t1/2) in rabbits (t1/2 = 4) and mice (t1/2 = 1.3 h).     

Quantitative determination of octadecenedioic acid in human skin and transdermal perfusates by gas chromatography-mass spectrometry

A gas chromatographic (GC) method with mass spectrometric (MS) detection is developed and validated for the accurate and precise determination of octadecenedioic acid (C18:1 DIOIC) in human skin samples and transdermal perfusates. C18:1 DIOIC is extracted using methanol. The saturated analogue 1,18-octadecanedioic acid (C18:0 DIOIC) is added as internal standard. Prior to analysis, both compounds are converted to their trimethylsilylated derivatives using N,O-bis(trimethylsilyl)trifluoroacetamide with 15% trimethylchlorosilane. Quantitation is performed in selected ion monitoring mode with a limit of quantitation of 250 ng/mL. Linearity with a correlation coefficient of 0.998 is obtained over a concentration range of 250-2000 ng/mL. Values for within-day accuracy range from 94.5% to 102.4%, and from 97.5% to 105.8% for between-day accuracy. Within- and between-day precision values are better than 5% and 7%, respectively. The recovery values from the various matrices vary from 92.6% to 104.0%. The GC-MS method is employed for the determination of C18:1 DIOIC after application of an emulsion containing the active ingredient onto human skin in vitro. The results demonstrate that the method is suitable for the determination of C18:1 DIOIC in human skin samples and transdermal perfusates.     

Rapid HPLC analysis of the antiepileptic lamotrigine and its metabolites in human plasma

A liquid chromatographic method with diode array detection (DAD) has been developed for the analysis of the antiepileptic agent lamotrigine (LTG) and its metabolites, lamotrigine 2-N-glucuronide and 2-N-methylated in plasma samples. The analytes were separated on a C8 RP column, using a mobile phase composed of methanol and a 0.45 mM, pH 3.5 phosphate buffer containing 0.17% triethylamine (24:76 v/v). Melatonin was used as the internal standard (IS). The DAD detector was set at 220 nm for the detection of all the analytes. A simple protein precipitation with methanol guaranteed high extraction yield values (>90%) and good purification from matrix interference. Good linearity was obtained in the 0.1-15.0 microg/mL range for LTG and lamotrigine 2-N-glucuronide and in the 0.1-2.0 microg/mL range for lamotrigine 2-N-methylated. The analytical method was validated in terms of precision, extraction yield, and accuracy. These assays gave RSD% values for precision always lower than 4.3% and mean accuracy higher than 80%. The method seems to be suitable for the analysis of plasma samples from patients treated with Lamictal.     

New method for determination of (E)-resveratrol in wine based on microextraction using packed sorbent and ultra-performance liquid chromatography

An ultra-fast and improved analytical methodology based on microextraction by packed sorbent (MEPS) combined with ultra-performance LC (UPLC) was developed and validated for determination of (E)-resveratrol in wines. Important factors affecting the performance of MEPS such as the type of sorbent material (C2, C8, C18, SIL, and M1), number of extraction cycles, and sample volume were studied. The optimal conditions of MEPS extraction were obtained using C8 sorbent and small sample volumes (50-250 μL) in one extraction cycle (extract-discard) and in a short time period (about 3 min for the entire sample preparation step). (E)-Resveratrol was eluted by 1×250 μL of the mixture containing 95% methanol and 5% water, and the separation was carried out on a high-strength silica HSS T3 analytical column (100 mm × 2.1 mm, 1.8 μm particle size) using a binary mobile phase composed of aqueous 0.1% formic acid (eluent A) and methanol (eluent B) in the gradient elution mode (10 min of total analysis). The method was fully validated in terms of linearity, detection (LOD) and quantification (LOQ) limits, extraction yield, accuracy, and inter/intra-day precision, using a Madeira wine sample (ET) spiked with (E)-resveratrol at concentration levels ranging from 5 to 60 μg/mL. Validation experiments revealed very good recovery rate of 95±5.8% RSD, good linearity with r(2) values >0.999 within the established concentration range, excellent repeatability (0.52%), and reproducibility (1.67%) values (expressed as RSD), thus demonstrating the robustness and accuracy of the MEPS(C8) /UPLC-photodiode array (PDA) method. The LOD of the method was 0.21 μg/mL, whereas the LOQ was 0.68 μg/mL. The validated methodology was applied to 30 commercial wines (24 red wines and six white wines) from different grape varieties, vintages, and regions. On the basis of the analytical validation, the MEPS(C8)/UPLC-PDA methodology shows to be an improved, sensitive, and ultra-fast approach for determination of (E)-resveratrol in wines with high resolving power within 6 min.     

Rapid method for the determination of capsaicin and dihydrocapsaicin in Gochujang using ultra-high-performance liquid chromatography

A sensitive and specific heating block method coupled with ultra-HPLC (u-HPLC) was developed for the analysis of capsaicin in Gochujang and validated by comparing with a conventional HPLC (AOAC Method 995.03). The method validation parameters yielded good results, including linearity, precision, accuracy, and recovery. The u-HPLC separation was performed on a reversed C18 column (50 x 2 mm id, particle size 2 microm), followed by fluorescence detection (excitation 280 nm, emission 325 nm). Methanol was used as the extracting solvent, and the amount of sample taken was approximately 0.2 g; the optimum amount of extraction solvent and extraction time were 15 mL and 1 h, respectively. The recovery of capsaicin in Gochujang was more than 93%, and the LOD and LOQ of the u-HPLC analysis were 0.05 and 0.16 microg/g for capsaicin and 0.05 and 0.16 microg/g for dihydrocapsaicin. The calibration graphs for capsaicin and dihydrocapsaicin were linear from 0.2 to 10.0 microg/mL for u-HPLC. The interday and intraday precisions (RSD values) were < 6.27%.     

Rapid and quantitative extraction method for the determination of chlorophylls and carotenoids in olive oil by high-performance liquid chromatography

Colour is an organoleptic characteristic of virgin olive oil and an important attribute that affects the consumer perception of quality. Chlorophylls and carotenoids are the main pigments responsible for the colour of virgin olive oil. A simple analytical method for the quantitative determination of chlorophylls and carotenoids in virgin olive oils has been developed. The pigments were isolated from small samples of oil (1.0 g) by solid-phase extraction using diol-phase cartridges (diol-SPE), and the extract was analysed by reverse-phase HPLC with diode-array UV detection. Chromatographic peak resolution, reproducibility (coefficient of variation (C.V.) <4.5%) and recovery (>98.4%) for each component were satisfactory. A comparative study of the proposed method was performed versus classical liquid-liquid extraction (LLE) with N,N′-dimethylformamide and solid-phase extraction using a C18 column (C18-SPE). While 96.4% of the pigments were recovered by LLE, only 51.3% were isolated by C18-SPE in comparison to diol-SPE. Likewise, a higher alteration of pigment composition was observed when such LLE and C18-SPE procedures were used. In this sense, a higher ratio of pheophytin in comparison to that isolated by the diol-SPE procedure was achieved with both extraction procedures, indicating a greater extent of the pheophytinization reaction. Therefore, quantification of pigments from virgin olive oil by diol-SPE followed by RP-HPLC was found to be rapid, simple, required only a small amount of sample, consumed only small amounts of organic solvents, and provided high recoveries, accuracy and precision.     

Determination of MK-0431 in human plasma using high turbulence liquid chromatography online extraction and tandem mass spectrometry

A robust and sensitive method using high turbulence liquid chromatography (HTLC) online extraction with tandem mass spectrometry (MS/MS) for the determination of MK-0431 in human plasma was developed and validated to support the clinical studies. This HTLC online extraction method eliminated the time-consuming offline sample extraction procedures and significantly increased productivity. A narrow bore large particle size reversed-phase column (Cyclone, 50 x 1.0 mm, 60 microm) and a BDS Hypersil C18 column (30 x 2.1 mm, 3 microm) were used as extraction and analytical columns, respectively. The linear dynamic range of the calibration curve was 0.5 to 1000 ng/mL. Intraday validation was conducted using five calibration curves prepared in five lots of human control plasma, and the intraday precision (RSD%) was from 2.4 to 9.0% and the accuracy was from 98.0 to 103% of the nominal value. The intraday precision (RSD%, n = 5) for plasma quality control (QC) samples varied from 2.0 to 5.3% and accuracy from 103 to 105% of the nominal value. The interday precision (RSD%) for 100 sets of plasma QC samples in 29 analytical runs varied from 6.3 to 9.0% and the accuracy from 98.8 to 104% of the nominal value. No significant difference was observed between the interday and intraday precision and accuracy of the QC samples.     

Determination of atrazine, deethylatrazine and simazine in water at parts-per-trillion levels using solid-phase extraction and gas chromatography/ion trap mass spectrometry

Methods for trace analysis of atrazine and simazine in water have been developed by using stable-isotope dilution with detection by gas chromatography/mass spectrometry. D(5)-Atrazine was used as the internal standard for the determination of atrazine and deethylatrazine, while (13)C(3)-simazine was used for simazine analysis. Water samples were fortified with known amounts of the internal standards and submitted to solid-phase extraction with a C(18) bonded-silica cartridge. A gas chromatograph coupled with an ion-trap mass spectrometer was used to analyze the water sample extracts. Method detection limits were 38 parts-per-trillion (ppt) for atrazine and deethylatrazine and 75 ppt for simazine. The accuracy of the method, represented by relative analytical errors, was less than 15%, and the method precision was less than 5% (relative standard deviation, n = 9). The method was successfully applied to analyze surface water samples collected from a reservoir and a river at ppt levels.     

Simple, sensitive and rapid liquid chromatography/atmospheric pressure chemical ionization mass spectrometric method for the quantitation of Ranolazine in rat plasma

A sensitive and specific method using liquid chromatography with atmospheric pressure chemical ionization mass spectrometry (LC/APCI-MS) has been developed and validated for the identification and quantification of Ranolazine in rat plasma. A simple liquid-liquid extraction procedure was followed by injection of the extracts onto a C18 column with isocratic elution and detection using a single quadrupole mass spectrometer in selected ion monitoring (SIM) mode. The method was tested using six different batches of blank plasma. Linearity was established for the concentration range 0.02-10.0 microg/mL, with a coefficient of determination (r) of 0.9998 and good back-calculated accuracy and precision. The intra- and inter-day precision (relative standard deviation (RSD) %) was lower than 10%, and accuracy ranged from 85 to 115%. The lower limit of quantification was reproducible at 0.01 microg/mL with 20 microL plasma. The proposed method enables the unambiguous identification and quantification of Ranolazine for pre-clinical and clinical studies.     

Quantitation of simvastatin and its beta-hydroxy acid in human plasma by liquid-liquid cartridge extraction and liquid chromatography/tandem mass spectrometry

A sensitive and reliable procedure for the simultaneous determination of simvastatin (SV) and its active beta-hydroxy acid metabolite (SVA) in human plasma was developed and validated. The analytes were extracted simultaneously from 0.5 ml aliquots of human plasma samples by methyl tert-butyl ether (MTBE) via Chem Elut cartridge extraction [also called liquid-solid extraction (LSE) or liquid-liquid cartridge extraction (LLCE)], separated through a Kromasil C(18) column (50 x 2 mm i.d. 5 microm) and detected by tandem mass spectrometry with a turbo ionspray interface. Stable isotope-labeled SV and SVA, (13)CD(3)-SV and (13)CD(3)-SVA, were used as internal standards. SV and SVA were detected in positive and negative ion modes, respectively, via within-run polarity switching. The use of Chem Elut cartridges not only provided a simple and efficient means of plasma sample extraction but also successfully reduced the interconversion between SV and SVA to an undetectable (for lactonization of SVA) or negligible (<0.07%, for hydrolysis of SV) level. The method showed excellent reproducibility, with intra- and inter-assay precisions <4.5% (RSD), and intra- and inter-assay accuracy between 94% and 107% of nominal values, for both analytes. The extraction recoveries were 78% and 87% on average for SV and SVA, respectively. The analyte was found to be stable in plasma through three freeze (-70 degrees C)-thaw (4 degrees C) cycles and for at least 3 h under bench-top storage condition in an ice-bath (4 degrees C), and also in the reconstitution solution at 4 degrees C for at least 24 h. The method has a lower limit of quantitation (LOQ) of 50 pg ml(-1) with a linear calibration range of 0.05-50 ng ml(-1) for both analytes, and has proved to be very reliable for the analysis of clinical samples.     

Detection of Phthalate Esters in Environmental Water Samples-Comparison of Nylon6 Nanofibers Mat-based Solid Phase Extraction and Other Conventional Extraction Methods

In this article, a new method for simultaneous determination of six phthalate esters was developed by a combination of electrospun nylon6 nanofibers mat‐based solid phase extraction with high performance liquid chromatography‐ultraviolet detector (HPLC‐UV). The six phthalate esters were dimethyl phthalate (DMP), diethyl phthalate (DEP), butyl benzyl phthalate (BBP), di‐n‐butyl phthalate (DBP), di‐(2‐ethylhexyl) phthalate (DEHP) and dioctyl phthalate (DOP). Under optimized conditions, all target analytes in 50 mL environmental water samples could be completely extracted by 2.5 mg nylon6 nanofibers mat and eluted by 100 µL solvent. Compared with C18 cartridges solid phase extraction, C18 disks solid phase extraction and national standard method (China), nylon6 nanofibers mat‐based solid phase extraction was advantageous in aspects of simple and fast operation, low consumption of extraction materials and organic solvents. The four methods were applied to analysis of environment water samples. All the results indicated that the determination values of target compounds with the proposed method were consistent with C18 cartridges and C18 disks solid phase extraction method, and the new method was better than the national standard method in aspects of recovery, LOD and precision. Therefore, nylon6 nanofibers mat has great potential as a novel material for solid phase extraction.     

Improved procedure for the the determination of rofecoxib in human plasma involving 96-well solid-phase extraction and fluorescence detection

An improved assay for the determination of rofecoxib in human plasma samples is described. The analyte and an internal standard were extracted from the plasma matrix using solid-phase extraction in the 96-well format with an Empore C8-SD extraction plate. The analytes are chromatographed on a Waters Symmetry C18 analytical column (3.5 microm, 50x4.6 mm) with a mobile phase consisting of acetonitrile-water (35:65, v/v). Analyte detection was via fluorescence following post-column photochemical derivatization. Eight point calibration curves over the concentration range of 0.5-80 ng/ml yielded a linear response when a 1/y weighted linear regression model was employed. Based on the replicate analyses (n=5) of spiked standards, the within-day assay precision was better than 8% RSD at all points on the calibration curve, within-day accuracy was within 6% of nominal at all standard concentrations. The between-run precision and accuracy of the assay, as calculated from the results of the analysis of quality control samples, was better than 7% RSD and within 5% of nominal. Assay throughput was improved by a factor of three as compared to previously described methods. The method was partially automated using a combination of a Packard Multi-Probe liquid handling system and a TomTec Quadra 96 workstation.     

Development and validation of a reliable high-performance liquid chromatographic method for determination of nodakenin in rat plasma and its application to pharmacokinetic study

A simple and reliable high-performance liquid chromatographic (HPLC) method has been developed for the determination of nodakenin in rat plasma. The concentration of nodakenin was determined in plasma samples after deproteinization with methanol using hesperidin as internal standard. HPLC analysis was performed on a Diamonsil C(18) analytical column using acetonitrile-water (25:75, v/v) as the mobile phase and a UV detection at 330 nm. This method was validated in terms of recovery, linearity, accuracy and precision (intra- and inter-day variation). The extraction recoveries were 91.3 ± 10, 87.8 ± 4.8 and 92.6 ± 5.1 at concentrations of 0.500, 5.00 and 40.0 μg/mL, respectively. The standard curve for nodakenin was linear (r(2) ≥ 0.99) over the concentration range 0.250-50.0 μg/mL with a lower limit of quantification of 0.250 μg/mL. The intra- and inter-day precision (relative standard deviation, RSD) values were not higher than 12% and the accuracy (relative error, RE) was within ± 5.8% at three quality control levels. The validated method was successfully applied for the evaluation of the pharmacokinetics of nodakenin in rats after oral administration of Rhizoma et Radix Notopterygii decoction and nodakenin solution.     

多壁纳米碳管固相萃取测定水中的有机氯农药

对于水样中的有机氯农药的净化方法主要是采用传统的液液分配的方法,缺点是溶剂使用量和前处理复杂。近年来固相萃取及固相微萃取等技术被应用到水样中的有机污染物的测定。如利用键合在硅胶上的非极性(C18,LC18等)或极性物质(LC-CN,LC-NH2)对水中有机物进行富集,用GDX或XAD自填的固相柱的报道也很多。纳米技术和纳米材料的发展为开发固相萃取材料带来新契机。纳米材料是指尺寸大小在从1～100m之间物质。与普通的块体材料相比,纳米材料具有较大的比表面,因而有可能具有较大吸附容量。纳米材料在环境有机污染物分离富集方面的应用研究才刚刚开始。本文主要就纳米碳管对水样中的有机氯农药进行研究,优化固相萃取条件。     

Multiresidue analytical method of pesticides in peanut oil using low-temperature cleanup and dispersive solid phase extraction by GC-MS

A method for the determination of 33 pesticides in peanut oil by GC-MS was described. Two extraction procedures based on (i) low-temperature extraction and (ii) liquid-liquid extraction were tested for the optimization of the method. The mixture of anhydrous MgSO(4) with primary secondary amine (PSA) or with PSA and C(18) was performed as sorbents in dispersive SPE. Low temperature along with PSA and C(18) cleanup gave the best results. Pesticides were identified and quantified by GC-MS in SIM mode. The correlation coefficients, R(2), in the linear range tests were better than 0.990. The average recoveries for most pesticides (spiked at 0.02, 0.05, 0.2, and 1 mg/kg) ranged from 70 to 110%, the RSD was below 20% in most instances, and LODs varied from 0.5 to 8 mug/kg.     

A sensitive and selective LC-differential mobility-mass spectrometric analysis of allopregnanolone and pregnanolone in human plasma

A sensitive and selective method was developed to quantitate allopregnanolone and its 5β isomer pregnanolone in human plasma using liquid chromatography-differential mobility separation combined with MS/MS detection. The method employed a simple liquid–liquid extraction of 100 μL plasma with hexane/ethyl acetate. After extraction, the sample was derivatized using a quaternary aminooxy reagent. Separation of allopregnanolone, pregnanolone, and their 3β epimers (epiallopregnanolone and epipregnanolone) was achieved using a Phenomenex Kinetex C18 2.1?×?100-mm 2.6-μm column. A linear calibration curve was obtained over the concentration range from 10 to 25,000 pg/mL, and the inter- and intra-day accuracy of the quality control samples were between 90 and 110 % with the inter- and intra-day precision less than 10 %. The lower limit of quantitation is 50 fg (157 amol) on column for both allopregnanolone and pregnanolone which is 100-fold less than the underivatized compounds. The recovery is above 95 %, and the extracted samples are stable for at least 6 days when stored at 4 °C. Plasma samples from normal, pregnant, and postpartum women were analyzed using this method.     

Determination of pesticides in sugarcane juice employing microextraction by packed sorbent followed by gas chromatography and mass spectrometry

This paper describes the development of a method for the determination of six pesticides (tebuthiuron, carbofuran, atrazine, metribuzine, ametryn, and bifenthrin) in sugarcane juice using microextraction by packed sorbent as the extraction technique. The extraction steps were optimized by factorial design, being the variables pH, ionic strength, desorption solvent and solvent volume optimized for comparisons among sorbent materials. Among the evaluated materials C18‐Chromabond ^® showed better extraction efficiency. A factorial design 2³ with central point was used for the extraction cycles optimization. Draw/eject and washes cycles showed significant improvements in the extraction efficiency when the number of cycles increased. The method was validated and showed a limit of quantification in the range of 2.0–10.0 μg.L^?1. The calibration curves were constructed by weighting models that reduced the sum of absolute residues values and improved determination coefficient. The matrix factor and extraction efficiency were 97.3–77.3% and 27.1–64.8%, respectively. The accuracy was 71.7–106.9%; precision evaluated as the coefficient of variance obtained in intra and inter day analysis was 4.5–15.9%. The method was applied to the determination of pesticide residues in four sugarcane juice samples commercially available in markets from different cities from São Paulo state, Brazil.     

An installation for the preparation of foraminifera micro samples for the isotopic analysis of carbon and oxygen

A technical modification of the traditional method of decomposition of carbonates in phosphoric acid was proposed for the determination of δ¹³C and δ¹⁸O in organogenic carbonate samples weighing 10–30 μg with an accuracy of 0.05%. The extraction of CO₂ was carried out under a vacuum at 95°C in 105% phosphoric acid. The isotopic composition of CO₂ was measured by CG-IRMS. The used feed-motion of samples to the reactor provides a consecutive delivery of the samples from the sample holders to the acid. This sample feeding method prevents the contamination of the acid with impurities from the surface of the sample, obviates the necessity of removing the sample holders from the acid, and allows the use of the same acid for performing a very large numbers of analyses. The accuracy and reproducibility of the δ¹³C and δ¹⁸O values was estimated by measuring international standards and comparing with the δ¹³C and δ¹⁸O values for organogenic carbonate samples obtained by the proposed method of analysis at a microgram level and the traditional method at a milligram level. The proposed technology was successfully used to study the isotopic composition of oxygen and carbon in the plankton and benthos foraminifers in order to reconstruct the Okhotsk Sea palaeotemperatures.     

Extraction of sodium and potassium perchlorates with benzo-18-crown-6 into various organic solvents. Quantitative elucidation of anion effects on the extraction-ability and -selectivity for Na(+) and K(+)

To investigate quantitatively the anion effect on the extraction-ability and -selectivity of benzo-18-crown-6 (B18C6) for alkali metal ions, the constants for overall extraction into various diluents having low dielectric constants (K(ex)) and aqueous ion-pair formation (K(MLA)) of B18C6-sodium and potassium perchlorate 1:1:1 complexes (MLA) were determined at 25 degrees C. The K(ex) value was analyzed by the four fundamental equilibrium constants. The K(MLA) values were determined by applying our established method to this perchlorate extraction system. The K(M(B18C6)A) value of the perchlorate is much larger for K(+) than for Na(+), and is much smaller than that of the picrate. The K(M(B18C6)A) value makes a minor contribution to the magnitude of K(ex) for the perchlorate system, but a major contribution to that for the picrate one. The distribution behavior of the B18C6 1:1:1 complexes with the alkali metal perchlorates follows the regular solution theory. For the diluent with a high dipole moment, however, the 1:1:1 complexes somewhat undergo the dipole-dipole interaction. B18C6 always shows very high extraction selectivity for KClO(4) over NaClO(4), which is determined mostly by the much greater log/(log K(MLA)) value for K(+) than for Na(+). The extraction-ability and -selectivity of B18C6 for Na(+) and K(+) ions with a perchlorate ion were compared with those with a picrate ion in terms of the fundamental equilibrium constants. The K(+) extraction-selectivity of B18C6 over Na(+) for the perchlorate system is superior to that for the picrate one, which is caused largely by the greater log/(log K(K(B18C6)A))-log/(log K(Na(B18C6)A)) value for the perchlorate than for the picrate. The perchlorate system is recommended for extraction separation of K(+) from Na(+).