Characteristics of low-temperature-grown GaN films on Si(111)

In this paper, we report on the characteristics of GaN films grown on Si(111) at a low temperature (200 °C) by electron cyclotron resonance (ECR) plasma-assisted metalorganic chemical vapor deposition (PA-MOCVD). Structural analysis of the GaN films was performed by using scanning electron microscopy (SEM), atomic force miscroscopy (AFM), X-ray diffraction (XRD), energy dispersive X-ray analysis (EDX), and Rutherford backscattering spectrometry (RBS). Post deposition analysis revealed high quality crystalline GaN was obtained at this low temperature. Electrical analysis of the GaN films was done by using current-voltage (I-V) measurements where electrical characterizations were carried on GaN/Si heterojunction and Schottky barrier diodes. Rectification behaviour was observed for the isotype GaN/Si (n-n) heterojunction. Ideality factors and Schottky barrier heights for Ni and Cr Schottky barriers on GaN, were deduced to be 1.4 and 1.7; and 0.62 and 0.64 eV, respectively.     

On the characteristics of AlGaN films grown on (111) and (001) Si substrates

High Al-content Al_xGa_1−xN films were deposited on (001) and (111) Si substrates at 1000 °C using high temperature AlN buffer layers. Experimental results show that Al_xGa_1−xN films grown on (111) Si substrates exhibit better crystalline quality than that in the films deposited on (001) Si substrates. Cracks were found in the high Al-content Al_xGa_1−xN/(111) Si samples but they were not observed in the Al_xGa_1−xN films grown on (001) Si substrates having the same film thicknesses and Al compositions. Based upon the results of X-ray diffraction (XRD) and transmission electron microscopy (TEM), it appears that mono-crystalline Al_xGa_1−xN films were achieved on (111) Si substrates while columnar structure was observed in the Al_xGa_1−xN/(001) Si samples. According to the depth profiles of Al_xGa_1−xN/Si samples using secondary ion mass spectroscopic (SIMS) analyses, enhanced Al inter-diffusion in the Al_xGa_1−xN/(001) Si samples was identified. Room temperature (RT) photoluminescence (PL) measurements of the Al_xGa_1−xN (x≦0.10)/(111) Si samples exhibit strong near band edge luminescence. The PL emission linewidth was found to decrease with the decrement of Al-content.     

Morphological properties of AlN and GaN grown by MOVPE on porous Si(111) and Si(111) substrates

Metal Organic Vapour Phase Epitaxy (MOVPE) of AlN and GaN layers at a temperature of 1080 C were performed on porous Si(111) and Si(111) substrates. The thermal stability of porous silicon (PS) is studied versus growth time under AlN and GaN growth conditions. The surface morphology evolution of the annealed PS is revealed by scanning electron microscopy (SEM). Porous Si(111) with low porosity (40%) is more thermally stable than porous Si(100) with relatively high porosity (60%).AlN layers with various thicknesses were grown under the same conditions on the two substrates. Morphological properties of AlN were studied by atomic force microscopy (AFM) and compared taking into account the two different surfaces of the substrates. The two growth kinetics of AlN were found to be different due to the initial surface roughness of the PS substrate. The effect of AlN buffer morphology on the qualities of subsequent GaN layers is discussed. Morphological qualities of GaN layers grown on PS are improved compared to those obtained on porous Si(100) but are still less than those grown on Si substrate.     

Preparation and properties of GaN films on Si(111) substrates

High-quality gallium nitride (GaN) films were prepared on Si(111) substrates by sputtering post-annealing-reaction technique. XRD, XPS, and SEM measurement results indicate that polycrystalline GaN with hexagonal structure was successfully prepared. Intense room- temperature photoluminescence that peaked at 354 nm of the films is observed. The bandgap of these films has a blueshift with respect to bulk GaN.     

Si(110)和Si(111)衬底上制备InGaN/GaN蓝光发光二极管

分别在Si(110)和Si(111)衬底上制备了In Ga N/Ga N多量子阱结构蓝光发光二极管(LED)器件.利用高分辨X射线衍射、原子力显微镜、室温拉曼光谱和变温光致发光谱对生长的LED结构进行了结构表征.结果表明,相对于Si(111)上生长LED样品,Si(110)上生长的LED结构晶体质量较好,样品中存在较小的张应力,具有较高的内量子效率.对制备的LED芯片进行光电特性分析测试表明,两种衬底上制备的LED芯片等效串联电阻相差不大,在大电流注入下内量子效率下降较小;但是,相比于Si(111)上制备LED芯片,Si(110)上LED芯片具有较小的开启电压和更优异的发光特性.对LED器件电致发光(EL)发光峰随驱动电流的变化研究发现,由于Si(110)衬底上LED结构中阱层和垒层存在较小的应力/应变而在器件中产生较弱的量子限制斯塔克效应,致使Si(110)上LED芯片EL发光峰随驱动电流的蓝移量更小.     

Temperature-dependent photoluminescence spectra of GaN epitaxial layer grown on Si(111) substrate

In this paper, the temperature-dependent photoluminescence(PL) properties of Ga N grown on Si(111) substrate are studied. The main emission peaks of Ga N films grown on Si(111) are investigated and compared with those grown on sapphire substrates. The positions of free and bound exciton luminescence peaks, i.e., FX A and D0 X peaks, of Ga N films grown on Si(111) substrates undergo red shifts compared with those grown on sapphire. This is attributed to the fact that the Ga N films grown on sapphire are under the action of compressive stress, while those grown on Si(111) substrate are subjected to tensile stress. Furthermore, the positions of these peaks may be additionally shifted due to different stress conditions in the real sample growth. The emission peaks due to stacking faults are found in Ga N films grown on Si(111) and an S-shaped temperature dependence of PL spectra can be observed, owing to the influence of the quantum well(QW) emission by the localized states near the conduction band gap edge and the temperature-dependent distribution of the photo-generated carriers.     

The influence of SixNy interlayer on GaN film grown on Si(111) substrate

A method to drastically reduce dislocation density in a GaN film grown on an Si(111) substrate is newly developed. In this method, the Si_xN_y interlayer which is deposited on an AlN buffer layer in situ is introduced to grow the GaN film laterally. The crack-free GaN film with thickness over 1.7 micron is grown on an Si(111) substrate successfully. Synthesized GaN epilayer is characterized by X-ray diffraction (XRD), atomic force microscope (AFM), and Raman spectrum. The test results show that the GaN crystal reveals a wurtzite structure with the <0001> crystal orientation and the full width at half maximum of the X-ray diffraction curve in the (0002) plane is as low as 403 arcsec for the GaN film grown on the Si substrate with an Si_xN_y interlayer. In addition, Raman scattering is used to study the stress in the sample. The results indicate that the Si_xN_y interlayer can more effectively accommodate the strain energy. So the dislocation density can be reduced drastically, and the crystal quality of GaN film can be greatly improved by introducing Si_xN_y interlayer.     

In-situ wafer bowing measurements of GaN grown on Si(111) substrate by reflectivity mapping in metal organic chemical vapor deposition system

In this work, the wafer bowing during growth can be in-situ measured by a reflectivity mapping method in the 3×2 Thomas Swan close coupled showerhead metal organic chemical vapor deposition(MOCVD) system. The reflectivity mapping method is usually used to measure the film thickness and growth rate. The wafer bowing caused by stresses(tensile and compressive) during the epitaxial growth leads to a temperature variation at different positions on the wafer, and the lower growth temperature leads to a faster growth rate and vice versa. Therefore, the wafer bowing can be measured by analyzing the discrepancy of growth rates at different positions on the wafer. Furthermore, the wafer bowings were confirmed by the ex-situ wafer bowing measurement. High-resistivity and low-resistivity Si substrates were used for epitaxial growth. In comparison with low-resistivity Si substrate, Ga N grown on high-resistivity substrate shows a larger wafer bowing caused by the highly compressive stress introduced by compositionally graded Al Ga N buffer layer. This transition of wafer bowing can be clearly in-situ measured by using the reflectivity mapping method.     

Structure and ultraviolet photoluminescence of 3C-SiC films grown on Si(111)

The structure and light-emitting properties of nanocrystalline cubic silicon carbide films prepared by chemical conversion from hexane vapors are discussed. The morphology, the composition, and the crystallographic structure of the grown silicon carbide thick films are thoroughly analyzed using X-ray diffraction, electron diffraction, white light interferometry, and scanning probe and transmission electron microscopies. The excitation with the use of the third harmonic of a femtosecond laser (λ_excit = 266 nm) makes it possible for the first time to reveal the luminescence line lying in the deep UV region with the wavelength λ = 340 nm in addition to the usually observed lines in the high-temperature photoluminescence spectrum. The nature of the lines observed in the photoluminescence spectrum is discussed.     

Magnetic properties of Co films grown on the modified Si(111) surface

The magnetic properties and domain structure of epitaxial Co films grown on a modified Si(111) surface were studied. First, the processes of growth of copper silicide nanostructures on the Si(111) surface were investigated. Copper silicide clusters were formed on the Si(111)-5.55 × 5.55-Cu surface at a substrate temperature of ～550°C. It was established that the nanostructures formed have a perfect faceting, and the lateral edges and long wire side are oriented along the Si〈110〉 crystallographic directions. Then, Co films were deposited on the formed structures. The investigation of the coercive force and reduced remanent magnetization showed that the Co(111) films have the sixth-order crystalline anisotropy. It was found that the coercive force of the Co films deposited on the Cu buffer layer is approximately six times less than that of the Co films deposited on the Si(111)-5.55 × 5.55-Cu surface and Si(111)?5.55 × 5.55-Cu/(Cu-Si) cluster surface.     

Growth and structure of epitaxial diamond films grown on Si(111) single crystals

Experiments on growing single-crystal diamond films on silicon crystals with (111) surface orientation have been performed. Results attesting to the possibility of obtaining thin heteroepitaxial films are presented. Pis’ma Zh. éksp. Teor. Fiz. 65, No. 5, 414–418 (10 March 1997)     

Si(111)衬底上GaN的MOCVD生长

利用LP-MOCVD在Si（111）衬底上,以高温AIN为缓冲层,分别用低温GaN（LT-GaN）和偏离化学计量比富Ga高温GaN（HT-GaN）为过渡层外延生长六方相GaN薄膜。采用高分辨率双晶X射线衍射（DCXRD）,扫描电子显微镜（SEM）,原子力显微镜（AFM）和室温光致荧光光谱（RT-PL）进行分析。结果表明,有偏离化学计量比富Ga HT-GaN为过渡层生长的GaN薄膜质量和光致荧光特性均明显优于以LT-GaN为过渡层生长的GaN薄膜,得到GaN（0002）和（1012）的DCXRD峰,其半峰全宽（FWHM）分别为698s和842s,室温下的光致荧光光谱在361nm处有一个很强的发光峰,其半峰全宽为44．3meV。     

The influence of AlN/GaN superlattice intermediate layer on the properties of GaN grown on Si（111） substrates

AlN/GaN superlattice buffer is inserted between GaN epitaxial layer and Si substrate before epitaxial growth of GaN layer. High-quality and crack-free GaN epitaxial layers can be obtained by inserting AlN/GaN superlattice buffer layer. The influence of AlN/GaN superlattice buffer layer on the properties of GaN films are investigated in this paper. One of the important roles of the superlattice is to release tensile strain between Si substrate and epilayer. Raman spectra show a substantial decrease of in-plane tensile strain in GaN layers by using AlN/GaN superlattice buffer layer. Moreover, TEM cross-sectional images show that the densities of both screw and edge dislocations are significantly reduced. The GaN films grown on Si with the superlattice buffer also have better surface morphology and optical properties.     

Columnar AlGaN/GaN nanocavities with AlN/GaN Bragg reflectors grown by molecular beam epitaxy on Si(111)

Self-assembled columnar AlGaN/GaN nanocavities, with an active region of GaN quantum disks embedded in an AlGaN nanocolumn and cladded by top and bottom AlN/GaN Bragg mirrors, were grown. The nanocavity has no cracks or extended defects, due to the relaxation at the Si interface and to the nanocolumn free-surface to volume ratio. The emission from the active region matched the peak reflectivity by tuning the Al content and the GaN disks thickness. Quantum confinement effects that depend on both the disk thickness and the inhomogeneous strain distribution within the disks are clearly observed.     

The effect of single A1GaN interlayer on the structural properties of GaN epilayers grown on Si （111） substrates

High-quality and nearly crack-free GaN epitaxial layer was obtained by inserting a single AlGaN interlayer between GaN epilayer and high-temperature AlN buffer layer on Si (111) substrate by metalorganic chemical vapor deposition. This paper investigates the effect of AlGaN interlayer on the structural properties of the resulting GaN epilayer. It confirms from the optical microscopy and Raman scattering spectroscopy that the AlGaN interlayer has a remarkable effect on introducing relative compressive strain to the top GaN layer and preventing the formation of cracks. X-ray diffraction and transmission electron microscopy analysis reveal that a significant reduction in both screw and edge threading dislocations is achieved in GaN epilayer by the insertion of AlGaN interlayer. The process of threading dislocation reduction in both AlGaN interlayer and GaN epilayer is demonstrated.     

Microstructural properties of GaN grown on a Si(110) substrate by gas-source molecular beam epitaxy: Dependence on the ammonia flux

The microstructural properties of a GaN thin film grown on a Si(110) substrate under various ammonia (NH₃)-flux conditions were observed to study growth mode and defect evolution. The surface flatness of GaN thin films was improved with the increase of the NH₃ flux while the thickness was decreased by increasing the NH₃ flux. In addition, the crystalline quality of the GaN film grown under the lower NH₃ flux (100 sccm) was better than that of the film under the higher NH₃ flux (400 sccm). The different dislocation behaviors depending on NH₃ fluxes were observed; the low density of dislocations was measured and most of dislocations penetrating the thin film was mixed- and edge-type dislocations when GaN was grown under the low NH₃ flux condition while the high density of dislocation and many mixed- and screw-type dislocations penetrating the film were observed in the GaN film grown under the high NH₃ flux. These phenomena are demonstrated by using a kinetic model related to the role of NH₃.     

等离子辅助分子束外延技术研究生长在Si(111)衬底的氮化镓pn结

利用等离子辅助分子束外延系统研究了生长在硅(111)衬底的氮化镓pn结,并将其应用于光学器件．硅和镁分别用做n和p掺杂,反射高能电子衍射图像显示氮化镓pn结层具有良好的表面形貌,结层厚度约为0.705 nm,且为六方结构．室温下X射线衍射对称摇摆曲线中(0002)面的ω/2θ显示,半峰宽为0.340,说明氮化镓pn结质量高．另外,在硅和镁掺杂样品中没有A1峰淬灭．光致发光光谱表明pn结样品具有良好的光学性能．镍和铝作为分别作为正面和背面的电极接触应用于光学器件,该器件的电流电压特性显示了典型的异质结整流特性．正向接触镍经过氮气中退火处理10 min,结果表明,600 oC处理的样品比400 oC处理和未经处理的样品具有更高的增益．     

Growth and optical properties of filamentary GaN nanocrystals grown on a hybrid SiC/Si(111) substrate by molecular beam epitaxy

The potential to grow filamentary GaN nanocrystals by molecular beam epitaxy on a silicon substrate with a nanosized buffer layer of silicon carbide has been demonstrated. Morphological and optical properties of the obtained system have been studied. It has been shown that the intensity of the photoluminescence spectrum peak of such structures is higher than that of the best filamentary GaN nanocrystals without the buffer silicon carbide layer by a factor of more than two.     

The effect of sub-band gap photon illumination on the properties of GaN layers grown on Si(111) by MBE

Nanostructured GaN layers are fabricated by laser-induced etching processes based on heterostructure of n-type GaN/AlN/Si grown on n-type Si(111) substrate. The effect of varying laser power density on the morphology of GaN nanostructure layer is observed. The formation of pores over the structure varies in size and shape. The etched samples exhibit dramatic increase in photoluminescence intensity compared to the as-grown samples. The Raman spectra also display strong band at 522 cm⁻¹ for the Si(111) substrate and a small band at 301 cm⁻¹ because of the acoustic phonons of Si. Two Raman active optical phonons are assigned h-GaN at 139 and 568 cm⁻¹ due to E2 (low) and E2 (high), respectively. Surface morphology and structural properties of nanostructures are characterized using scanning electron microscopy and X-ray diffraction. Photoluminance measurement is also taken at room temperature by using He–Cd laser (λ = 325 nm). Raman scattering is investigated using Ar⁺ Laser (λ = 514 nm).     

Study of the structural and magnetic characteristics of epitaxial Fe3Si/Si(111) films

The results of the structural and magnetic studies of the epitaxial structure prepared during the simultaneous evaporation from two iron and silicon sources on an atomically pure Si(111)7 × 7 surface at a substrate temperature of 150°C have been presented. The epitaxial structure has been identified as a single-crystal Fe₃Si silicide film with the orientation Si[111]‖Fe₃Si[111] using methods of the X-ray structural analysis, transmission electron microscopy, and reflection high-energy electron diffraction. It has been established that the epitaxial Fe₃Si film at room temperature has magnetic uniaxial anisotropy (H _a = 26 Oe) and a relatively narrow uniform ferromagnetic resonance line (ΔH = 11.57 Oe) measured at a pump frequency of 2.274 GHz.