Photoluminescence and optical characterization of CdS nanoparticles prepared by solid-state method at low temperature

The photoluminescence (PL) and optical properties of CdS nanoparticles prepared by the solid-state method at low temperature have been discussed. The effects of NaCl and anionic surfactant SDBS (sodium dodecylbenzene sulfonate) on the luminescent properties of CdS nanophosphors prepared using this method, without the inert gas or the H₂S environment, were studied separately. The synthesized products were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), field emission scanning electron microscope (FESEM), and energy dispersive X-ray spectroscopy (EDAX). UV–VIS absorption and PL spectra were also studied. XRD studies confirmed the single-phase formation of CdS nanoparticles. TEM micrograph revealed the formation of nearly spherical nanoparticles with a diameter of 2.5 nm. The PL emission for the CdS shows the main peak at 560 nm with a shoulder at 624 nm, with an increase in the PL intensity after the addition of SDBS. The effect of Mn doping on PL intensity has also been investigated. The PL spectra show that the emission intensity decreases as the dopant concentration increases.     

核/壳结构的ZnS:Mn/SiO_2纳米粒子的制备及发光性质研究

采用溶剂热法制备了Mn离子掺杂的ZnS纳米粒子(ZnS∶Mn),然后利用正硅酸乙酯(TEOS)的水解反应对其进行了不同厚度的SiO2无机壳层包覆。采用X射线衍射(XRD)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)及荧光发射光谱(PL)对样品的结构及光学性质进行了表征和研究。包覆SiO2壳层后,粒子的粒径明显增大并且在ZnS∶Mn纳米粒子表面可以观察到明显的SiO2壳层。XPS测试印证了ZnS∶Mn/SiO2的核壳结构。随着SiO2壳层的增厚,ZnS∶Mn/SiO2的Mn离子的发光先增强后减弱,这是因为SiO2壳层同时具有表面修饰和降低发光中心浓度这两种相反的作用。当壳层厚度(壳与核的物质的量的比)达到5时,发光效果达到最好,其强度达到未包覆样品的7.5倍。     

核/壳结构ZnS : Mn/CdS纳米粒子的制备及发光

利用溶剂热法制备了Mn离子掺杂的ZnS纳米粒子(ZnS : Mn),利用沉淀法对ZnS ∶ Mn纳米粒子进行了不同厚度的CdS无机壳层包覆。采用X射线衍射(XRD)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)及光致发光(PL)光谱等手段对样品进行了表征。TEM显示粒子为球形,直径大约在14~18 nm之间。由XRD结果可以看出CdS壳层的形成过程受到了ZnS ∶ Mn核的影响,导致其结晶较差。XRD和XPS测量证明了ZnS : Mn/CdS的核壳结构。随着CdS壳层的增厚,样品的发光强度呈现一直减弱的现象。     

核壳结构CdS/ZnS纳米微粒的制备与光学特性

用微乳液法制备CdS纳米微粒 ,以ZnS对其进行表面修饰 ,得到具有核壳结构的CdS/ZnS纳米微粒 .采用X射线衍射 (XRD)、透射电镜 (TEM )表征其结构、粒度和形貌 ,紫外 可见吸收光谱 (UV)、光致发光光谱(PL)表征其光学特性 .制得的CdS近似呈球形 ,直径为 3.3nm ;以XRD和UV证实了CdS/ZnS核壳结构的实现 .研究了不同ZnS壳层厚度对CdS纳米微粒光学性能的影响 ,UV谱表明随着壳层厚度的增加纳米微粒的吸收带边有轻微的红移 ,同时短波吸收增强 ;PL谱表明壳层ZnS的包覆可减少CdS纳米微粒的表面缺陷 ,带边直接复合发光的几率增大 ,具有合适的壳层厚度时发光效率大大提高 .     

The optical properties and energy transition process in nanocomposite of polyvinyl-pyrrolidone polymer and Mn-doped ZnS

This study has been carried out on the optical properties of polyvinyl-pyrrolidone (PVP), the energy transition process in nanocomposite of PVP capped ZnS:Mn nanocrystalline and the influence of the PVP concentration on the optical properties of the PVP capped ZnS:Mn nanocrystalline thin films synthesized by the wet chemical method. The microstructures of the samples were investigated by X-ray diffraction, the atomic absorption spectroscopy, and transmission electron microscopy. The results showed that the prepared samples belonged to the sphalerite structure with the average particle size of about 2–3 nm. The optical properties of samples are studied by measuring absorption, photoluminescence (PL) spectra and time-resolved PL spectra in the wavelength range from 200 to 700 nm at 300 K. From data of the absorption spectra, the absorption edge of PVP polymer was found about of 230 nm. The absorption edge of PVP capped ZnS:Mn nanoparticles shifted from 322 to 305 nm when the PVP concentration increases. The luminescence spectra of PVP showed a blue emission with peak maximum at 394 nm. The luminescence spectra of ZnS:Mn–PVP exhibits a blue emission with peak maximum at 437 nm and an orange–yellow emission of ion Mn²⁺ with peak maximum at 600 nm. While the PVP coating did not affect the microstructure of ZnS:Mn nanomaterial, the PL spectra of the PVP capped ZnS:Mn samples were found to be affected strongly by the PVP concentration.     

Influences of capping molecules on optical properties of nanocrystalline ZnS:Cu

ZnS:Cu nanocrystals capped with different capping molecules have been successfully synthesized by a simple aqueous method. The prepared nanocrystals were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive analysis by X-rays (EDAX). The surface characterization of the nanocrystals was done by FTIR spectroscopy. The effect of capping agents on absorption and photoluminescence (PL) spectra of the ZnS:Cu nanocrystals was studied. A blue shift of the absorption peaks was observed and attributed to a quantum confinement effect, which increases the band gap energy. The photoluminescence spectra of the capped ZnS:Cu nanocrystals showed a broad peak in the range of 460–480 nm. The intensity of the PL spectra strongly depended on the capping agents.     

Formation of zinc sulfide nanoparticles in HMTA matrix

A hydrothermal method has been optimized for the synthesis of ZnS nanoparticles. The nanoparticles were stabilized using Hexamethylenetetramine (HMTA) as surfactant in aqueous solution. The self-assembling of the surfactant molecules in the water solution forms a unique architecture that can be adopted as the reaction template for the formation of nanomaterials. The average grain size of the nanoparticles calculated from the XRD pattern was of the order of 2 nm which exhibits cubic zinc-blende structure. TEM results showed that the synthesized nanoparticles were uniformly dispersed in the HMTA matrix without aggregation. The spectroscopic results revealed that the synthesized ZnS nanoparticles exhibits strong quantum confinement effect as the optical band gap energy increased significantly compared to the bulk ZnS material. Formation of HMTA capped ZnS nanoparticles were confirmed by FTIR studies. The PL spectra exhibit a strong green emission peak around 502 nm attributed to some self-activated defect centers related to Zn-vacancies.     

Luminescence properties of co-doped ZnS:Ni,Mn and ZnS:Cu,Cd nanoparticles

Transition metal doped ZnS:Ni and ZnS:Cu and co-doped ZnS:Ni, Mn and ZnS:Cu, Cd nanoparticles were synthesized through the chemical precipitation method in an air atmosphere. The XRD analysis of co-doped samples shows the formation of cubic phase. The average size of nanoparticles ranges from 3.6 to 5.5 nm. The formation of co-doped nanoparticles was confirmed by XRD and PL analysis. The PL spectra show that the obtained nanoparticles have good crystal quality. An optimum concentration of transition metals was selected in co-doped ZnS nanoparticles.     

Synthesis, structural and optical characterization of nanocrystalline ZnS:Cu embedded in silica matrix

The synthesis of Cu doped ZnS nanoparticles inside the pore of an inorganic silica gel matrix is presented. The synthesized nanoparticles were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray (EDX). X-ray diffraction pattern reveals the crystalline wurtzite phase of ZnS. The existence of silica gel in modeling morphologies of the nanoparticles was characterized using Fourier transform infrared (FTIR) spectrometer. Thickness of the silica shell was also calculated. UV- absorption spectrum shows the appearance of an absorption peak at 273 nm which confirms the blue shift as compared to that of bulk ZnS. The photoluminescence (PL) emission spectrum of the sample showed a broad band in the range 465-510 nm due to the transition from the conduction band edge of ZnS nanocrystals to the acceptor like t₂ state of Cu.     

Synthesis and photoluminescent and nonlinear optical properties of manganese doped ZnS nanoparticles

In this work we synthesized ZnS:Mn²⁺ nanoparticles by chemical method using PVP (polyvinylpyrrolidone) as a capping agent in aqueous solution. The structure and optical properties of the resultant product were characterized using UV-vis optical spectroscopy, X-ray diffraction (XRD), photoluminescence (PL) and z-scan techniques. UV-vis spectra for all samples showed an excitonic peak at around 292 nm, indicating that concentration of Mn²⁺ ions does not alter the band gap of nanoparticles. XRD patterns showed that the ZnS:Mn²⁺ nanoparticles have zinc blende structure with the average crystalline sizes of about 2 nm. The room temperature photoluminescence (PL) spectrum of ZnS:Mn²⁺ exhibited an orange-red emission at 594 nm due to the ⁴T₁-⁶A₁ transition in Mn²⁺. The PL intensity increased with increase in the Mn²⁺ ion concentration. The second-order nonlinear optical properties of nanoparticles were studied using a continuous-wave (CW) He-Ne laser by z-scan technique. The nonlinear refractive indices of nanoparticles were in the order of 10⁻⁸ cm²/W with negative sign and the nonlinear absorption indices of these nanoparticles were obtained to be about 10⁻³ cm/W with positive sign.     

Synthesis and photoluminescence of water-soluble Mn-doped ZnS quantum dots

The water-soluble Mn²⁺-doped ZnS quantum dots (Mn:ZnS d-dots) were synthesized by using thioglycolic acid (TGA) as stabilizer in aqueous solutions in air, and characterized by X-ray powder diffraction (XRD), UV-vis absorption spectra and photoluminescence (PL) emission spectroscopy. The sizes of Mn:ZnS d-dots were determined to be about 2 nm using XRD measurements and the UV-vis absorption spectra. It was found that the Mn²⁺⁴T₁ → ⁶A₁ emission intensity of Mn:ZnS d-dots significantly increased with the increase of Mn²⁺ concentration, and showed a maximum when Mn²⁺ doping content was 1.5%. If Mn²⁺ concentration continued to increase, namely more than 1.5%, the Mn²⁺⁴T₁ → ⁶A₁ emission intensity would decrease. In addition, the effects of TGA/(Zn + Mn) molar ratio on PL were investigated. It was found that the peak intensity ratio of Mn²⁺⁴T₁ → ⁶A₁ emission to defect-states emission showed a maximum when the TGA/(Zn + Mn) molar ratio was equal to 1.8.     

Synthesis and characterization of Cu doped ZnS nanoparticles using TOPO and SHMP as capping agents

Undoped and Cu²⁺ doped (0.2-0.8%) ZnS nanoparticles have been synthesized through chemical precipitation method. Tri-n-octylphosphine oxide (TOPO) and sodium hexametaphosphate (SHMP) were used as capping agents. The synthesized nanoparticles have been analyzed using X-ray diffraction (XRD), transmission electron microscope (TEM), Fourier transform infrared spectrometer (FT-IR), UV-vis spectrometer, photoluminescence (PL) and thermo gravimetric-differential scanning calorimetry (TG-DTA) analysis. The size of the particles is found to be 4-6 nm range. Photoluminescence spectra were recorded for ZnS:Cu²⁺ under the excitation wavelength of 320 nm. The prepared Cu²⁺-doped sample shows efficient PL emission in 470-525 nm region. The capped ZnS:Cu emission intensity is enhanced than the uncapped particles. The doping ions were identified by electron spin resonance (ESR) spectrometer. The phase changes were observed in different temperatures.     

Synthesis and stabilization of ZnS nanoparticles embedded in silica nanospheres

The silica-coated ZnS nanocomposites have been synthesized by a seeded-growth procedure in iso-propanol. The results of XRD, HRTEM and UV absorption show that the ZnS nanoparticles can be incorporated in the silica nanospheres without changing the particle size, and the composites are of multi-core structure. UV absorption and emission spectra have been performed to check the character of the composites, which show that the silica shell not only increases the PL intensity, but also greatly improves the anti-oxidation ability and thermal stability. PACS 81.05.Dz; 81.16.Be; 81.65.Rv; 78.55.Et; 78.66.Hf     

Synthesis and characterization of aqueous MPA-capped CdS–ZnS core–shell quantum dots

The novel CdS–ZnS core–shell nanoparticles are synthesized using simple one-step aqueous chemical approach. 3-mercaptopropionic acid (MPA) was used as the capping molecule. The structural and optical properties of the prepared samples are characterized by X-ray diffraction (XRD), UV–vis absorption spectroscopy, photoluminescence (PL) spectroscopy, energy-dispersive X-ray (EDX) and transition electron microscopy (TEM). The studies show that pH contributed noticeably to the growth and optical properties of nanoparticles. The TEM results indicate that the prepared particles have core–shell structure.     

Photoluminescent properties of ZnS nanoparticles prepared by electro-explosion of Zn wires

We study the photoluminescent properties of ZnS nanoparticles without the influence of dopants or magnetic impurities. The ZnS nanoparticles reported in this case were synthesized by a novel method of electro-explosion of wire (EEW). The nanoparticles were prepared employing electro-explosion of pure zinc wires in a cell filled with sulfide ions to produce a free-standing compound ZnS semiconductor. To investigate the structural and optical properties, these nanoparticles were characterized by X-ray powder diffraction (XRD), atomic force microscopy (AFM), UV–visible and photoluminescence (PL) spectroscopy. Consistent with the enhancement of the PL intensity of the 443 nm peak due to deep blue emission of ZnS particles, the XRD of the nanoparticles reveals a hexagonal phase of ZnS nanocrystallites prepared by our novel synthesis technique.      

Preparation, characterization and study of optical properties of ZnS nanophosphor

In this work the preparation, characterization and photoluminescence studies of pure and copper-doped ZnS nanophosphors are reported, which are prepared by using solid-state reaction technique at a temperature of 100 °C. The as-obtained samples were characterized by X-ray diffraction (XRD) and UV-VIS Reflectance spectroscopy. The XRD analysis confirms the formation of cubic phase of undoped as well as Cu²⁺-doped ZnS nanoparticles. Furthermore it shows that the average size of pure as well as copper-doped samples ranges from 15 to 50 nm. The room-temperature PL spectra of the undoped ZnS sample showed two main peaks centered at around 421 and 450 nm, which are the characteristic emissions of interstitial zinc and sulfur vacancies, respectively. The PL of the doped sample showed a broad-band emission spectrum centered at 465 nm accompanied with shoulders at around 425, 450 and 510 nm, which are the characteristic emission peaks of interstitial zinc, sulfur vacancies and Cu²⁺ ions, respectively. Our experimental results indicate that the PL spectrum confirms the presence of Cu²⁺ ions in the ZnS nanoparticles as expected.     

Investigations on structural and optical properties of Zn1−xGdxS nanoparticles

Zn_1−xGd_xS (x = 0.00, 0.02 and 0.04) nanoparticles were synthesized by facile chemical co-precipitation method using PVP as a surfactant. ZnS nanoparticles could be doped with Gd ions during synthesis without altering the XRD patterns of ZnS. Also, the pattern of the powders showed cubic zincblende structure. The particle size obtained from the XRD studies lies in the range 3-5 nm, whereas from TEM analysis it is 4 nm for x = 0.02 sample. The UV-Vis absorption spectra revealed that Zn_1−xGd_xS nanoparticles exhibit strong confinement effect as the blue shift in the absorption spectra with that of the undoped ZnS. The photoluminescence spectra showed enhanced luminescence intensity and the entry of Gd into host lattice.     

Study of optical and thermal properties in nickel doped ZnS nanoparticles using surfactants

The presence of surfactants polyethylene glycol (PEG), polyvinyl pyrrolidone (PVP), sodium hexameta polyphosphate (SHMP) and tri-octyl phosphine oxide (TOPO) on the surface of Ni²⁺ doped ZnS (ZnS:Ni²⁺) nanoparticles resulted variation in their optical properties. The optical properties of each surfactant-capped ZnS:Ni²⁺ nanoparticles were investigated using UV–visible (UV–Vis) absorption and photoluminescence (PL) techniques. The absorption spectra and fluorescent emission spectra showed a significant blue shift compared to that of the bulk zinc sulfide. The effect of the optical properties in colloidal form (wet) and dry samples were investigated. Enhanced PL emission was observed for the dry samples at 80 °C. Thermal properties of the ZnS:Ni²⁺ was also studied using thermo gravimetric-differential thermal analysis (TG-DTA), Fourier transform infra-red spectrometer (FT-IR) and X-ray diffraction (XRD). The results are presented and discussed.     

Synthesis and characterization of Mn<Superscript>2+</Superscript>-doped ZnS nanoparticles

Mn²⁺-doped ZnS nanoparticles were prepared by chemical arrested precipitation method. The samples were heated at 300, 500, 700 and 900°C. The average particle size was determined from the X-ray line broadening. Samples were characterized by XRD, FTIR and UV. The composition was verified by EDAX spectrum. The hexagonal structure of the sample was identified. The size of the particles increased as the annealing temperature was increased. The crystallite size varied from 5 nm to 34 nm as the calcination temperature increased. At around 700°C, ZnS is converted into ZnO phase due to oxidation. The emission peak of the sample is observed at 300 nm resulting in blue emission. The solid state theory based on the delocalized electron and hole within the confined volume can explain the blue-shifted optical absorption spectra. UV-VIS spectro-photometric measurement shows an indirect allowed band gap of 3.65 eV.      

氧化石墨烯/硒化锌纳米光电材料的制备及其蓝光发射特性

采用一种简单有效的原位水热合成方法,使用石墨烯氧化物（GO）作为反应物和晶体生长基底成功制备出了还原氧化石墨烯/硒化锌（r-GO/ZnSe）纳米复合材料。采用X射线粉末衍射（XRD）、透射电子显微镜（TEM）、高分辨透射电镜（HRTEM）以及红外-可见光谱（FT-IR）等方法对r-GO/ZnSe纳米复合材料进行了检测。结果表明,平均粒径在30 nm的立方闪锌矿晶体结构的ZnSe粒子均匀分散在氧化石墨烯片层上,构成纳米复合结构。 UV-Vis光谱显示,纳米复合材料的光学吸收的起始波长在445 nm附近。PL光谱显示,纳米复合材料在470 nm附近存在一个很强的发射峰。这种石墨烯基纳米复合材料在白光二极管领域中有重要的应用价值。