All-fiber,high power single-frequency linearly polarized ytterbium-doped fiber amplifier

We report an all-fiber high power,single frequency large-mode area (LMA) linearly polarized ytterbiumdoped fiber amplifiers (YDFA) module,which is based on the master oscillator multi-stage power amplifiers (MOPA).The maximum output power is 43.8 W at a wavelength of 1064 nm when 60-W launched pump light is coupled,with high slope efficiency of 88%,polarization extinction rate (PER) >17.2 dB and nearly diffraction-limited beam quality (M 2 <1.1).     

Power amplifier for 1064 nm using Yb3+-doped double-clad fiber

A master-oscillator fiber power amplifier(MOPA)system is presented,which consists of a single modelaser as the master oscillator and an Yba+-doped large-mode-area double-clad fiber as the power amplifier.The system emits up to 6 W of amplified radiation at a wavelength of 1064 nm.The slope efficiency andextracted pulse energy as a function of pulse repetition rate are analyzed.     

Er3+-doped phosphor-tellurite glass for broadband short-length Er3+-doped fiber amplifier

ErS+-doped phosphor-tellurite glass for broadband short-length Er3+-doped fiber amplifier (EDFA) is fabricated and characterized. The differential value (△T) of onset crystalline temperature (Tx) and glass transition temperature (Ts) is 206°C.     

全光纤结构高功率主振荡功率放大型单频光纤激光器

研制了一台全光纤结构主振荡功率放大型掺镱单频光纤激光器。该光纤激光器包括种子激光器和级联放大器两部分。种子激光器是自行搭建的环形腔结构的单频窄线宽光纤激光器。在976 nm半导体激光器泵浦下,能够输出线宽为10 MHz量级、波长为1 079.88 nm的单频光,激光功率为10.02 W,光-光转化效率为58.9%,斜率效率为65.3%。     

Tm3+掺杂光纤激光制冷的理论分析

近年来,掺Tm3+:ZBLANP玻璃已成为固体材料激光冷却领域中最有希望的新材料之一,但有关掺Tm3+:ZBLANP光纤的激光冷却尚未见到理论研究与实验报道.本文采用一个简单的理论模型,就Tm3+:ZBLANP光纤的激光冷却进行了理论研究与分析,讨论了量子效率、抽运功率、背景吸收、出射荧光波长变化和环境黑体辐射等对激光制冷效果的影响,得到了一些有趣的重要结果,可为掺Tm3+:ZBLANP光纤的激光冷却实验提供可靠的理论依据.     

Efficient approximately 2 microm Tm3+ -doped tellurite fiber laser

Laser emission in the range of 1.88-1.99 micrim from a Tm3+ -doped tellurite fiber is demonstrated when pumped with a diode-pumped Er3+/Yb3+-doped silica fiber laser operating at 1.57-1.61 microm. This pump source excites the Tm3+ ions directly into the F43 upper laser level and yields an output power of 280 mW with a slope efficiency of 76% in a 99%-12% laser cavity arrangement and a 32 cm long fiber. This result is very close to the Stokes efficiency limit of approximately 80%. This is, to the authors' knowledge, the first demonstration of high efficiency lasing in a tellurite fiber at wavelengths longer than 1.56 microm.     

CW single transverse mode all-fiber Tm3+-doped silica fiber laser

The CW 25.6 W output power with a slope efficiency of 30.6% respected to the pump power from a CW single transverse mode all-fiber Tm³⁺-doped Silica Fiber Laser is reported. The all-fiber laser is made up by progressively splicing the pigtail fiber, matched FBG fiber and Tm fiber. The reflective FBG and Tm³⁺-doped fiber end Fresnel reflection build up the laser resonance cavity. Due to the multi-mode FBG as the reflective mirror, the output laser spectrum is multi-peaks at high output power, but the spectrum width is less than 2 nm at 1.94 μm. We estimate the beam quality to be M ² = 2.39, clearly indicating nearly diffraction-limited beam propagation.     

LD泵浦掺铥(Tm3+)光纤激光器的数值分析

首先从掺铥光纤激光器的速率方程和光传输方程出发,建立数学模型,通过Matlab软件进行数值计算,分析了泵浦光和激光沿光纤的分布以及各能级离子数的变化.在不同掺杂浓度下,研究了小信号增益与入纤泵浦功率的关系以及泵浦光和激光功率与增益介质长度的关系.在不同泵浦功率下,研究了输出功率与输出耦合镜反射率的关系.进一步对不同泵浦吸收系数,研究了斜率效率和泵浦阈值与光纤长度的关系.分析结果表明存在最佳光纤长度和最佳耦合输出透过率,使得激光输出功率达到最佳值.     

LD泵浦掺铥(Tm3+)光纤激光器的数值分析

首先从掺铥光纤激光器的速率方程和光传输方程出发，建立数学模型，通过Matlab软件进行数值计算，分析了泵浦光和激光沿光纤的分布以及各能级离子数的变化。在不同掺杂浓度下，研究了小信号增益与入纤泵浦功率的关系以及泵浦光和激光功率与增益介质长度的关系。在不同泵浦功率下，研究了输出功率与输出耦合镜反射率的关系。进一步对不同泵浦吸收系数，研究了斜率效率和泵浦阈值与光纤长度的关系。分析结果表明：存在最佳光纤长度和最佳耦合输出透过率，使得激光输出功率达到最佳值。     

Short Tm3+-doped fiber lasers with watt-level output near 2 μm

High-power operation of diode-pumped fiber lasers at wavelength near 2μm are demonstrated with short length of heavily Tm3 -doped silica glass fibers. With 7-cm long fiber, a laser at near 2 μm is obtained with the threshold of 135 mW, maximum output power of 1.09 W, and slope efficiency of 9.6% with respect to the launched power from a laser diode at 790 nm. The output stability of this fiber laser is within 5%.The dependence of the performance of fiber lasers on the operation temperature and cavity configuration parameters is also investigated.     

Raman fiber laser improvement by using Yb3+-doped fiber

We report here the efficiency improvement in a fiber Raman laser by splicing to it short pieces of 10000-ppm Yb³⁺-doped fibers. The amplified spontaneous emission produced by the doped fiber started the stimulated Raman scattering earlier than the spontaneous scattering in the 350-m silica-fiber cavity. In the best case, when splicing to the cavity 127 cm of doped fiber, the pump threshold decreased from 2.9 down to 1.27 W, representing a 56% improvement. This power was close to the theoretical minimum of 1.25 W for very long fibers. The second stokes signal (1175 nm) was only present when the doped fibers were inserted. At 4-W pump, the non-doped cavity delivered 2 W of first stokes signal (1117 nm) that represent a 50% efficiency compared to ～3 W delivered (～75%) when a 34-cm doped fiber was inserted. This improvement is intended to reduce the cost of fiber Raman lasers because less powerful sources or shorter fibers are necessary to produce more stokes components.     

Modelling of Tm3+-doped LiNbO3 Waveguide Lasers

In this work, CW laser operation of Tm³⁺-doped LiNbO₃ channel waveguides has been modelled. The model is based on time dependent laser rate equations coupled with the laser signal and pump photon flux equations. Steady state solutions for the population densities, pump and signal powers are obtained by using finite difference discretization of the active volume. The effects of spectroscopic parameters such as concentration dependent cross-relaxation and excess waveguide loss have been analyzed. We demonstrate good agreement with experimental data previously reported in Zn-diffused LiNbO₃:Tm³⁺ channel waveguide lasers. It is shown also that laser performance can be substantially improved by optimizing the cavity length.     

基于光子晶体光纤的全光纤脉冲放大器

大型激光驱动器装置对光纤前端系统的输出脉冲能力提出了更高的要求,基于大模场光子晶体光纤的mJ级脉冲放大器技术是首先需要解决的关键技术问题。研究了大模场光子晶体的切割和熔接工艺,实现了全光纤结构集成。对1~10kHz重复频率、10ns脉宽、0.3nm线宽的方波脉冲进行了放大实验研究,对比研究了反向和正向泵浦方式对自发辐射放大的抑制效果,在1kHz获得0.6mJ,单横模脉冲输出,初步验证了基于此类系统获得大能量、高品质脉冲输出的能力。     

915nm泵浦混合掺铒/铒镱共掺双包层光纤放大器

研究了一种混合掺铒/铒镱共掺光纤放大器,用掺铒光纤放大器作为输入信号的预放大器,用铒镱共掺双包层光纤放大器作为主放大器。掺铒光纤放大器采用20m长掺铒光纤作为增益介质,采用最大输出功率318mW的单模半导体激光器二极管作为泵浦源,预放大器获得的最大输出功率是113mW。铒镱共掺光纤放大器采用14m长铒镱共掺双包层光纤作为增益介质,采用2个915nm多模半导体激光二极管作为泵浦源,在输入信号功率为10mW、信号波长1555nm时,混合光纤放大器获得了最大输出功率为32.04dBm,即1.6W,与此相应的混合光纤放大器的光-光转换效率为18.5%。     

High power wavelength-defined all-fiber Yb3+-doped double clad fiber laser

An all-fiber Yb3+-doped double-clad fiber laser using FBGs as cavity mirrors is investigated in this paper. Continuous-wave (CW) output power of 1.18 W with defined wavelength at 1.06 um and narrow line-width of less than 0.1 nm is obtained. The slope efficiency and the maximum optical-to-optical efficiency of laser output are 68% and 51%, respectively, with respect to absorbed pump power.     

基于光子晶体光纤的全光纤脉冲放大器

大型激光驱动器装置对光纤前端系统的输出脉冲能力提出了更高的要求,基于大模场光子晶体光纤的mJ级脉冲放大器技术是首先需要解决的关键技术问题。研究了大模场光子晶体的切割和熔接工艺,实现了全光纤结构集成。对1~10 kHz重复频率、10 ns脉宽、0.3 nm线宽的方波脉冲进行了放大实验研究,对比研究了反向和正向泵浦方式对自发辐射放大的抑制效果,在1 kHz获得0.6 mJ,单横模脉冲输出,初步验证了基于此类系统获得大能量、高品质脉冲输出的能力。     

Er^3＋-doped phosphor-tellurite glass for broadband short-length Er^3＋-doped fiber amplifier

Er^3＋-doped phosphor-tellurite glass for broadband short-length Er^3＋-doped fiber amplifier （EDFA） is fabricated and characterized. The differential value （AT） of onset crystalline temperature （Tx） and glass transition temperature （Tg） is 206 ℃. The stimulated emission cross section of Er^3＋ is calculated from absorption spectrum by McCumber theory and is 0.87 × 10 ^-20 cm^2 at 1532 nm. A broad 1.5-μm fluorescence spectrum with 54-nm full-width at half maximum （FWHM） is demonstrated. Especially, the maximum phonon energy of undoped phosphor-tellurite glass is 1100 cm^- 1, which restricts the upconversion luminescence. It is possible to pump efficiently at 980 nm. These results indicate Er^3＋-doped phosphor-tellurite glass is suitable for fabricating broadband short-length EDFA.     

High-pulse-energy actively Q-switched Tm3+-doped silica 2 microm fiber laser pumped at 792 nm

A diode-pumped Q-switched Tm(3+)-doped double-clad silica fiber laser is reported providing average powers of up to 30 W at pulse widths of only 41 ns and repetition rates in the range of 10-125 kHz. Up to 270 microJ pulse energy was produced. Amplified spontaneous emission (ASE) buildup limits the maximum peak power, and the pump power and average output power at the point of ASE induced clamping were found to depend linearly on the repetition rate.     

High-peak-power operation of a Q-switched Tm3+-doped silica fiber laser operating near 2 microm

A peak output power of greater than 4.1 kW and a pulse duration at FWHM of 150 ns have been obtained in a Q-switched Tm3+-doped silica fiber laser in the wavelength region near 2 microm when the laser was pumped with a Nd:YAG laser operating at 1.319 microm. An acousto-optic modulator was used as a Q-switching element and operated at repetition rates of as much as 30 kHz. A core diameter of 17 microm was used to increase the laser gain volume, permitting high-pump-power absorption and an output of high pulse energy and peak power. Stimulated Brillouin scattering was directly observed in the output pulse, and as much as 10 orders of stimulated Brillouin scattering was recorded. This is the first report to the authors' knowledge of high-peak-power operation of a Tm3+-fiber laser.     

Novel Tm3+-doped transparent fluorozirconate glass-ceramic containing nanocrystalline

A new transparent Tm3+-doped ZrF4-based nanocrystallized glass with the composition of 55ZrF4-20BaF2-18.8YF3-5AlF5-1.2TmF3 (mol%) (ZBYA) has been prepared by a conventional melting quenching technique and the subsequent heat treatment processes. The glass characteristic temperatures, the apparent activation energy, and the Avrami parameter for crystallization are estimated on the basis of different scanning calorimetry (DSC). The sizes of grown nanocrystals in the glass matrix appear to be 30-36.5 nm and it is studied as a function of the nucleation temperature, also the peak intensity of the nanocrystalline is studied as a function of the nucleation temperature from the X-ray diffraction (XRD) measurement. The microhardness measurement shows that the Vickers microhardness (Hv) values of the heat-treated glass samples are larger than that of the based glass about 17.26%-42.04%.