N,P‐Codoped Carbon Networks as Efficient Metal‐free Bifunctional Catalysts for Oxygen Reduction and Hydrogen Evolution Reactions

The high cost and scarcity of noble metal catalysts, such as Pt, have hindered the hydrogen production from electrochemical water splitting, the oxygen reduction in fuel cells and batteries. Herein, we developed a simple template‐free approach to three‐dimensional porous carbon networks codoped with nitrogen and phosphorus by pyrolysis of a supermolecular aggregate of self‐assembled melamine, phytic acid, and graphene oxide (MPSA/GO). The pyrolyzed MPSA/GO acted as the first metal‐free bifunctional catalyst with high activities for both oxygen reduction and hydrogen evolution. Zn–air batteries with the pyrolyzed MPSA/GO air electrode showed a high peak power density (310 W g^?1) and an excellent durability. Thus, the pyrolyzed MPSA/GO is a promising bifunctional catalyst for renewable energy technologies, particularly regenerative fuel cells.     

Dual‐Template Pore Engineering of Whey Powder‐Derived Carbon as an Efficient Oxygen Reduction Reaction Electrocatalyst for Primary Zinc‐Air Battery

Cost‐effective and high‐performance electrocatalysts for oxygen reduction reactions (ORR) are needed for many energy storage and conversion devices. Here, we demonstrate that whey powder, a major by‐product in the dairy industry, can be used as a sustainable precursor to produce heteroatom doped carbon electrocatalysts for ORR. Rich N and S compounds in whey powders can generate abundant catalytic active sites. However, these sites are not easily accessible by reactants of ORR. A dual‐template method was used to create a hierarchically and interconnected porous structure with micropores created by ZnCl₂ and large mesopores generated by fumed SiO₂ particles. At the optimum mass ratio of whey power: ZnCl₂ : SiO₂ at 1 : 3 : 0.8, the resulting carbon material has a large specific surface area close to 2000 m² g^?1, containing 4.6 at.% of N with 39.7% as pyridinic N. This carbon material shows superior electrocatalytic activity for ORR, with an electron transfer number of 3.88 and a large kinetic limiting current density of 45.40 mA cm^?2. They were employed as ORR catalysts to assemble primary zinc‐air batteries, which deliver a power density of 84.1 mW cm^?2 and a specific capacity of 779.5 mAh g^?1, outperforming batteries constructed using a commercial Pt/C catalyst. Our findings open new opportunities to use an abundant biomaterial, whey powder, to create high‐value‐added carbon electrocatalysts for emerging energy applications.     

碳纳米管负载金属卟啉电催化剂制备及其催化活性

采用微波合成法制备了多壁碳纳米管负载钴卟啉(CoTMPP/MWNT)电催化剂,利用透射电子显微镜对催化剂微观结构进行了表征,并通过旋转圆盘和旋转环盘技术对电催化剂的氧还原活性进行了评价.结果表明,与有机回流合成法制备的催化剂相比,微波法合成的CoTMPP/MWNT催化剂具有更好的氧还原性能,半波电位正向移动110mV;与多孔碳为载体的CoTMPP/BP2000催化剂相比,多壁碳纳米管为载体的CoTMPP/MWNT电催化剂的起始电位高10mV,还原电流损失低21%,表现出更好的氧还原活性和稳定性.在CoTMPP/MWNT电催化剂表面进行的氧还原过程中电子转移数为3·6,H2O2生成量为18%.MWNT独特的电子特性、强抗腐蚀能力及其与活性钴离子之间的相互作用有助于改善催化剂的氧化还原性能.     

Preparation and Catalytic Activity of Carbon Nanotube-Supported Metalloporphyrin Electrocatalyst

The multiwalled carbon nanotube-supported CoTMPP (CoTMPP/MWNT) electrocatalyst was prepared by the microwave synthesis method, and its microstructure was characterized using transmission electron microscopy. The electrocatalytic performance of CoTMPP/MWNT for oxygen reduction reaction (ORR) was evaluated by rotating disc electrode and rotating ring disc electrode technique. Compared with the CoTMPP/MWNT electrocatalyst prepared by the traditional organic reflux method, the one prepared by the microwave synthesis method showed better performance for ORR, and the half-wave potential exhibited a positive shift of 110 mV. Compared with CoTMPP/BP2000, the CoTMPP/MWNT electrocatalyst showed a 10 mV higher on-set potential and a 21% lower reduction current loss in ORR, indicating that the CoTMPP/MWNT electrocatalyst had higher catalytic activity and better stability than CoTMPP/BP2000. The number of exchanged electrons during ORR and the yield of peroxide were 3.6 and 18%, respectively. The high corrosion resistance and unique electronic property of MWNT, and the interaction between MWNT and active metal ions can efficiently improve the electrocatalytic performance of the CoTMPP/MWNT catalyst.     

负载硫化钴纳米颗粒的N、S共掺杂石墨烯氧还原电催化剂的制备及性能

采用D-氨基葡萄糖作为Co分散剂和碳源,硫脲作为氮源和硫源,以NaCl为模板制备负载硫化钴纳米颗粒的N、S共掺杂三维石墨烯氧还原电催化剂(CoS/N/S/rGO)。CoS/N/S/rGO具有良好的氧还原反应(ORR)活性,起始电位和半波电位分别为960和815 mV,性能与商业Pt/C相当。此外,CoS/N/S/rGO表现出明显的4电子转移特性和超低的过氧化氢产率。与基于Pt/C的锌-空气电池相比,基于CoS/N/S/rGO的锌-空气电池在6 mol·L~(-1) KOH和0.2 mol~(-1) Zn(CH_3COO)_2碱性电解质中显示出更高的恒电流放电性能以及更好的稳定性。     

Enhanced Intrinsic Catalytic Activity of λ‐MnO2 by Electrochemical Tuning and Oxygen Vacancy Generation

Chemically prepared λ‐MnO₂ has not been intensively studied as a material for metal–air batteries, fuel cells, or supercapacitors because of their relatively poor electrochemical properties compared to α‐ and δ‐MnO₂. Herein, through the electrochemical removal of lithium from LiMn₂O₄, highly crystalline λ‐MnO₂ was prepared as an efficient electrocatalyst for the oxygen reduction reaction (ORR). The ORR activity of the material was further improved by introducing oxygen vacancies (OVs) that could be achieved by increasing the calcination temperature during LiMn₂O₄ synthesis; a concentration of oxygen vacancies in LiMn₂O₄ could be characterized by its voltage profile as the cathode in a lithiun–metal half‐cell. λ‐MnO_2?z prepared with the highest OV exhibited the highest diffusion‐limited ORR current (5.5 mA cm^?2) among a series of λ‐MnO_2?z electrocatalysts. Furthermore, the number of transferred electrons (n) involved in the ORR was >3.8, indicating a dominant quasi‐4‐electron pathway. Interestingly, the catalytic performances of the samples were not a function of their surface areas, and instead depended on the concentration of OVs, indicating enhancement in the intrinsic catalytic activity of λ‐MnO₂ by the generation of OVs. This study demonstrates that differences in the electrochemical behavior of λ‐MnO₂ depend on the preparation method and provides a mechanism for a unique catalytic behavior of cubic λ‐MnO₂.     

锌活化Fe/Co/N掺杂的生物质碳基高效氧还原催化剂

为了推动清洁能源-燃料电池的广泛应用, 迫切需要研发成本低、 原料来源广泛的过渡金属基高效氧还原反应(ORR)催化材料, 来替代目前使用的贵金属铂基催化材料. 本文以铁和钴等非贵金属离子作为催化材料的主要活性位点, 通过金属-羧基/羟基螯合键原位预锚定在具有三维(3D)孔道结构、 富含羧基和羟基以及极易在水溶液中形成凝胶网络的海洋生物质材料海藻酸钠上, 经冷冻干燥得到气凝胶; 然后通过高温碳化, 得到活性位点均匀分布在具有多级孔结构的碳骨架中的高活性、 高稳定的Co/Zn/Fe/N@bio-C-2氧还原催化剂材料, 该催化剂包含2种不同的铁基活性材料(Fe₂O₃和Fe)以及2种不同的钴基活性材料(CoO和Co).利用硝酸锌作为活化剂来改善催化材料的孔道结构, 使制备碳材料的总面积从149.3 m²/g增加到325.3 m²/g. 通过一系列对比实验发现, Fe/Co双活性位点与合适比表面积的协同作用使得Co/Zn/Fe/N@bio-C-2获得了最佳的ORR催化活性.其在0.1 mol/L KOH溶液中起始电位达到0.99 V, 半波电位可达0.87 V.     

一锅法制备Fe2O3@Fe-N-C氧还原电催化剂及其锌-空气电池的性能研究

在金属空气电池和燃料电池阴极上的氧还原反应(ORR)对相关电化学能量转换装置的整体性能有重要影响,金属-氮-碳催化剂有望替代传统的商业Pt-C成为新一代ORR电催化剂。本文通过简便的一步热解工艺合成了具有Fe-N_x活性位点和Fe₂O₃纳米颗粒共存的电催化剂,Fe₂O₃@Fe-N-C-1000催化剂在0.1 mol·L^-1 KOH溶液中表现出良好的ORR活性,半波电位为0.84 V,应用在锌-空气电池中时也具有可以和商业Pt-C媲美的性能,能量密度为88.3 mW·cm^-2,同时和Pt-C相比具有更好电化学稳定性,表现出优良的ORR应用潜力。     

碱性介质中Fe/N/C催化剂的氧气还原反应催化性能研究

以氧化石墨烯(GO)为碳载体, K₃Fe(CN)₆同时作为N源和Fe源, 经热处理后构建了新型Fe/N/C结构的氧气还原催化剂. 在热处理过程中, 氧化石墨烯上的官能团分解脱离形成活性中心, Fe元素和N元素的同时掺杂是通过氧化石墨烯与K₃Fe(CN)₆之间的相互作用而实现的. 通过傅立叶变换红外光谱(FTIR)和X射线光电子能谱(XPS)表征证明了这种非贵金属催化剂中N元素和Fe元素的成功掺杂, 在催化剂中N元素主要是以吡啶式氮、吡咯式氮和石墨式氮的形式存在, Fe(Ⅱ)和Fe(Ⅲ)则与其中的吡啶式氮配位形成Fe-N_x结构. 采用循环伏安法(CV)和旋转圆盘电极(RDE)技术, 研究其在碱性介质中对氧气还原反应(ORR)的电催化性能. 实验结果显示: Fe/N/C催化剂具有良好的ORR电催化活性, 在碱性溶液中的起始电位为-0.15 V, 同时有着良好的稳定性和抗甲醇性能.     

Porous Mn2O3: A Low‐Cost Electrocatalyst for Oxygen Reduction Reaction in Alkaline Media with Comparable Activity to Pt/C

Preparing nonprecious metal catalysts with high activity in the oxygen reduction reaction (ORR) can promote the development of energy conversion devices. Support‐free porous Mn₂O₃ was synthesized by a facile aerosol‐spray‐assisted approach (ASAA) and subsequent thermal treatment, and exhibited ORR activity that is comparable to commercial Pt/C The catalyst also exhibits notably higher activity than other Mn‐based oxides, such as Mn₃O₄ and MnO₂. The rotating ring disk electrode (RRDE) study indicates a typical 4‐electron ORR pathway on Mn₂O₃. Furthermore, the porous Mn₂O₃ demonstrates considerable stability and a good methanol tolerance in alkaline media. In light of the low cost and high earth abundance of Mn, the highly active Mn₂O₃ is a promising candidate to be used as a cathode material in metal–air batteries and alkaline fuel cells.     

On the Influence of Oxygen on the Degradation of Fe‐N‐C Catalysts

Fe‐N‐C catalysts containing atomic FeN_x sites are promising candidates as precious‐metal‐free catalysts for oxygen reduction reaction (ORR) in proton exchange membrane fuel cells. The durability of Fe‐N‐C catalysts in fuel cells has been extensively studied using accelerated stress tests (AST). Herein we reveal stronger degradation of the Fe‐N‐C structure and four‐times higher ORR activity loss when performing load cycling AST in O₂‐ vs. Ar‐saturated pH 1 electrolyte. Raman spectroscopy results show carbon corrosion after AST in O₂, even when cycling at low potentials, while no corrosion occurred after any load cycling AST in Ar. The load‐cycling AST in O₂ leads to loss of a significant fraction of FeN_x sites, as shown by energy dispersive X‐ray spectroscopy analyses, and to the formation of Fe oxides. The results support that the unexpected carbon corrosion occurring at such low potential in the presence of O₂ is due to reactive oxygen species produced between H₂O₂ and Fe sites via Fenton reactions.     

Soft‐Templating Synthesis of N‐Doped Mesoporous Carbon Nanospheres for Enhanced Oxygen Reduction Reaction

The development of ordered mesoporous carbon materials with controllable structures and improved physicochemical properties by doping heteroatoms such as nitrogen into the carbon framework has attracted a lot of attention, especially in relation to energy storage and conversion. Herein, a series of nitrogen‐doped mesoporous carbon spheres (NMCs) was synthesized via a facile dual soft‐templating procedure by tuning the nitrogen content and carbonization temperature. Various physical and (electro)chemical properties of the NMCs have been comprehensively investigated to pave the way for a feasible design of nitrogen‐containing porous carbon materials. The optimized sample showed a favorable electrocatalytic activity as evidenced by a high kinetic current and positive onset potential for oxygen reduction reaction (ORR) due to its large surface area, high pore volume, good conductivity, and high nitrogen content, which make it a highly efficient ORR metal‐free catalyst in alkaline solutions.     

ZIF‐8 Derived Graphene‐Based Nitrogen‐Doped Porous Carbon Sheets as Highly Efficient and Durable Oxygen Reduction Electrocatalysts

Nitrogen‐doped carbon (NC) materials have been proposed as next‐generation oxygen reduction reaction (ORR) catalysts to significantly improve scalability and reduce costs, but these alternatives usually exhibit low activity and/or gradual deactivation during use. Here, we develop new 2D sandwich‐like zeolitic imidazolate framework (ZIF) derived graphene‐based nitrogen‐doped porous carbon sheets (GNPCSs) obtained by in situ growing ZIF on graphene oxide (GO). Compared to commercial Pt/C catalyst, the GNPCSs show comparable onset potential, higher current density, and especially an excellent tolerance to methanol and superior durability in the ORR. Those properties might be attributed to a synergistic effect between NC and graphene with regard to structure and composition. Furthermore, higher open‐circuit voltage and power density are obtained in direct methanol fuel cells.     

Pyrolysis of Animal Bones with Vitamin B12: A Facile Route to Efficient Transition Metal–Nitrogen–Carbon (TM‐N‐C) Electrocatalysts for Oxygen Reduction

By pyrolyzing cattle bones, hierarchical porous carbon (HPC) networks with a high surface area (2520 m² g^?1) and connected pores were prepared at a low cost and large scale. Subsequent co‐pyrolysis of HPC with vitamin B12 resulted in the formation of three‐dimensional (3D) hierarchically structured porous cobalt–nitrogen–carbon (Co‐N‐HPC) electrocatalysts with a surface area as high as 859 m² g^?1 as well as a higher oxygen reduction reaction (ORR) electrocatalytic activity, better operation stability, and higher tolerance to methanol than the commercial Pt/C catalyst in alkaline electrolyte.     

铁、氮掺杂石墨烯/碳黑复合材料的制备及氧还原电催化性能

以高含氮量的2-氨基咪唑为氮源,三氯化铁为铁源,高比表面积的KJ600碳黑为载体,通过水热法制得氨基咪唑聚合物前驱体,再经二次高温热处理,制得石墨烯/碳黑复合材料. 透射电镜表征显示该材料为石墨烯纳米片与碳黑颗粒的复合结构. BET表征表明这是一种多孔结构,具有很高的比表面积（882 m²•g^-1）,这有利于暴露更多活性位点,并促进传质. XRD证实催化剂中存在石墨烯,且石墨烯结构是在第一次热处理过程中形成的. 电化学测试表明,该催化剂在酸性和碱性介质中都具有很高的氧还原电催化活性和低H₂O₂产率,并且在碱性介质中对甲醇小分子的抗毒化性能明显优于商业Pt/C催化剂,展示出在实际燃料电池系统中的应用潜力.     

The Solid‐Phase Synthesis of an Fe‐N‐C Electrocatalyst for High‐Power Proton‐Exchange Membrane Fuel Cells

The environmentally friendly synthesis of highly active Fe‐N‐C electrocatalysts for proton‐exchange membrane fuel cells (PEMFCs) is desirable but remains challenging. A simple and scalable method is presented to fabricate Fe^II‐doped ZIF‐8, which can be further pyrolyzed into Fe‐N‐C with 3 wt % of Fe exclusively in Fe‐N₄ active moieties. Significantly, this Fe‐N‐C derived acidic PEMFC exhibits an unprecedented current density of 1.65 A cm^?2 at 0.6 V and the highest power density of 1.14 W cm^?2 compared with previously reported NPMCs. The excellent PEMFC performance can be attributed to the densely and atomically dispersed Fe‐N₄ active moieties on the small and uniform catalyst nanoparticles.     

S‐Doping of an Fe/N/C ORR Catalyst for Polymer Electrolyte Membrane Fuel Cells with High Power Density

Fe/N/C is a promising non‐Pt electrocatalyst for the oxygen reduction reaction (ORR), but its catalytic activity is considerably inferior to that of Pt in acidic medium, the environment of polymer electrolyte membrane fuel cells (PEMFCs). An improved Fe/N/C catalyst (denoted as Fe/N/C‐SCN) derived from Fe(SCN)₃, poly‐m‐phenylenediamine, and carbon black is presented. The advantage of using Fe(SCN)₃ as iron source is that the obtained catalyst has a high level of S doping and high surface area, and thus exhibits excellent ORR activity (23 A g^?1 at 0.80 V) in 0.1 M H₂SO₄ solution. When the Fe/N/C‐SCN was applied in a PEMFC as cathode catalyst, the maximal power density could exceed 1 W cm^?2.     

Efficient Fe‐Co‐N‐C Electrocatalyst Towards Oxygen Reduction Derived from a Cationic CoII‐based Metal–Organic Framework Modified by Anion‐Exchange with Potassium Ferricyanide

Fe‐Co‐N‐C electrocatalysts have proven superior to their counterparts (e.g. Fe‐N‐C or Co‐N‐C) for the oxygen reduction reaction (ORR). Herein, we report on a unique strategy to prepare Fe‐Co‐N‐C?x (x refers to the pyrolysis temperature) electrocatalysts which involves anion‐exchange of [Fe(CN)₆]^3? into a cationic Co^II‐based metal‐organic framework precursor prior to heat treatment. Fe‐Co‐N‐C‐900 exhibits an optimal ORR catalytic performance in an alkaline electrolyte with an onset potential (E_onset: 0.97 V) and half‐wave potential (E_1/2: 0.86 V) comparable to that of commercial Pt/C (E_onset=1.02 V; E_1/2=0.88 V), which outperforms the corresponding Co‐N‐C‐900 sample (E_onset=0.92 V; E_1/2=0.84 V) derived from the same MOF precursor without anion‐exchange modification. This is the first example of Fe‐Co‐N‐C electrocatalysts fabricated from a cationic Co^II‐based MOF precursor that dopes the Fe element via anion‐exchange, and our current work provides a new entrance towards MOF‐derived transition‐metal (e.g. Fe or Co) and nitrogen‐codoped carbon electrocatalysts with excellent ORR activity.