A Self‐assembled L‐Cysteine and Electrodeposited Gold Nanoparticles‐reduced Graphene Oxide Modified Electrode for Adsorptive Stripping Determination of Copper

Glassy carbon electrode (GCE) modified with L‐cysteine and gold nanoparticles‐reduced graphene oxide (AuNPs‐RGO) composite was fabricated as a novel electrochemical sensor for the determination of Cu²⁺. The AuNPs‐RGO composite was formed on GCE surface by electrodeposition. The L‐cysteine was decorated on AuNPs by self‐assembly. Physicochemical and electrochemical properties of L‐cysteine/AuNPs‐RGO/GCE were characterized by scanning electron microscopy, atomic force microscopy, energy dispersive spectroscopy, Raman spectroscopy, X‐ray diffraction, cyclic voltammetry and adsorptive stripping voltammetry. The results validated that the prepared electrode had many attractive features, such as large electroactive area, good electrical conductivity and high sensitivity. Experimental conditions, including electrodeposition cycle, self‐assembly time, electrolyte pH and preconcentration time were studied and optimized. Stripping signals obtained from L‐cysteine/AuNPs‐RGO/GCE exhibited good linear relationship with Cu²⁺ concentrations in the range from 2 to 60 μg L⁻¹, with a detection limit of 0.037 μg L⁻¹. Finally, the prepared electrode was applied for the determination of Cu²⁺ in soil samples, and the results were in agreement with those obtained by inductively coupled plasma mass spectrometry.     

Microwave‐Assisted Synthesis and Physicochemical Characterization of Tetrafuranylporphyrin‐Grafted Reduced‐Graphene Oxide

This work describes the design of a modified porphyrin that bears four furan rings linked by 1,2‐bis‐(2‐aminoethoxy)ethane spacers. This unit is a well‐suited scaffold for a Diels–Alder reaction with commercial reduced‐graphene oxide, which is also described in this paper. A new hybrid material is obtained, thanks to efficient grafting under microwave irradiation, and fully characterized in terms of structure (UV, TGA, Raman) and morphology (HR‐TEM and AFM). Potential applications in photo‐ and sonodynamic therapy are envisaged.     

铁酞菁/氮掺杂石墨烯复合物的电化学传感研究

本文用快速简便的方法制备了铁酞菁/氮掺杂石墨烯（FePc/N-G）修饰电极,用于定量检测半胱氨酸. 采用电化学方法对修饰电极的性能进行了表征,结果表明氮掺杂石墨烯负载铁酞菁修饰电极对半胱氨酸具有更宽的线性响应范围和较高的灵敏度.     

Photoelectrochemical Detection of Glucose by Using an Enzyme‐Modified Photoelectrode

A new photoelectrochemical method for the determination of glucose based on the photoelectrochemical effect of poly(thionine) photoelectrode to hydrogen peroxide (H₂O₂) was reported. The H₂O₂‐sensitive photoelectrode was fabricated by electropolymerizing thionine on the surface of ITO electrode. And then glucose oxidase was immobilized on the photoelectrode via the aid of chitosan enwrapping, forming an enzyme‐modified photoelectrode. The photoelectrode was employed as an electron acceptor; H₂O₂ from the catalytic reaction of enzyme was employed as an electron donor, developing an analytical method of glucose without hydrogen peroxidase. In the paper, the photoelectrochemical effects of photoelectrode to H₂O₂ and glucose were studied. The effects of the bias voltage and the electrolyte pH on the photocurrent were investigated. The linear response of glucose concentrations ranged from 0.05 to 2.00 mmol/L was obtained with a detection limit of 22.0 µmol/L and sensitivity of 73.2 nA/(mmol·L^?1). The applied feasibility of method was acknowledged through monitoring the glucose in practical samples.     

RGO-TiO2纳米管阵列的制备及其光电性能

采用阳极氧化的方法,通过调节阴、阳两电极间距制备不同壁厚的TiO₂纳米管阵列. 采用脉冲电还原沉积的方法将RGO负载于TiO₂纳米管阵列表面合成了RGO-TiO₂纳米管阵列. 相较于负载在薄壁TiO₂纳米管阵列上的RGO,负载于厚壁TiO₂纳米管阵列上的RGO得以充分还原,覆盖率大幅度提高,并显示出良好的光吸收性质和较低的电荷传输电阻,光电流大幅度增加.     

氧化石墨烯接枝碳纤维新型增强体的制备与表征

利用“Grafting-to”化学修饰法制备氧化石墨烯接枝国产碳纤维新型增强体。利用红外光谱、X射线光电子能谱和原子力显微镜对样品的官能团和表面形貌进行表征;利用接触角测量、单丝拉伸方法研究了接枝前后纤维单丝的润湿性能及拉伸强度,并通过微脱粘法分析了其复合材料的界面剪切强度。结果表明：氧化石墨烯的接枝修饰使国产碳纤维表面粗糙度提高了166%,表面能提高了46.3%,拉伸强度提高了7.8%,复合材料的界面剪切强度提高了111.7%。     

The synthesis of graphene oxide covalently linked with nickel tetraamino phthalocyanine: A photoelectrochemical sensor for the analysis of rifampicin irradiated with blue light

In this article, the fabrication and characterization of a photoelectrochemical (PEC) rifampicin sensor based on graphene oxide grafted with Ni tetraamino phthalocyanine was described, which presents an excellent PEC activity, sensitivity, and material stability. The synthesized graphene oxide grafted with Ni tetraamino phthalocyanine was characterized using ultraviolet–visible (UV–vis), Fourier transform infrared (FTIR), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) analyses. Specifically, detection for rifampicin was based on the reduction of photocurrent caused by binding of the analyte to the sensing electrode surface. The fabricated sensor was characterized in a broad linear response range (0.025–71.3 μM) and with a low detection limit (2.5 nM), outperforming the previously reported sensors and thus being well suited for quality control and other applications, as confirmed by successful real‐life sample testing.     

Photoelectrochemical Complexes of Fucoxanthin‐Chlorophyll Protein for Bio‐Photovoltaic Conversion with a High Open‐Circuit Photovoltage

Open‐circuit photovoltage (V_oc ) is among the critical parameters for achieving an efficient light‐to‐charge conversion in existing solar photovoltaic devices. Natural photosynthesis exploits light‐harvesting chlorophyll (Chl) protein complexes to transfer sunlight energy efficiently. We describe the exploitation of photosynthetic fucoxanthin‐chlorophyll protein (FCP) complexes for realizing photoelectrochemical cells with a high V_oc . An antenna‐dependent photocurrent response and a V_oc up to 0.72 V are observed and demonstrated in the bio‐photovoltaic devices fabricated with photosynthetic FCP complexes and TiO₂ nanostructures. Such high V_oc is determined by fucoxanthin in FCP complexes, and is rarely found in photoelectrochemical cells with other natural light‐harvesting antenna. We think that the FCP‐based bio‐photovoltaic conversion will provide an opportunity to fabricate environmental benign photoelectrochemical cells with high V_oc , and also help improve the understanding of the essential physics behind the light‐to‐charge conversion in photosynthetic complexes.     

Photoelectrochemical Properties of Annealed Anodic TiO2 Layers Covered with CuOx

In this work, we present a systematic study on the influence of Cu²⁺ ion concentration in the impregnation solution on the morphology, structure, optical, semiconducting, and photoelectrochemical properties of anodic CuO_x-TiO₂ materials. Studied materials were prepared by immersion in solutions with different concentrations of (CH₃COO)₂Cu and subjected to air-annealing at 400 °C, 500 °C, or 600 °C for 2 h. The complex characterization of all studied samples was performed using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), reflectance measurements, Mott–Schottky analyses, and photocurrent measurements. It was found that band gap engineering based on coupling CuO with TiO₂ (E_g~3.3 eV) is an effective strategy to increase the absorption in visible light due to band gap narrowing (CuO_x-TiO₂ materials had E_g~2.4 eV). Although the photoactivity of CuO-TiO₂ materials decreased in the UV range due to the deposition of CuO on the TiO₂ surface, in the Vis range increased up to 600 nm at the same time.     

Preparation and Characterization of a Tin Pentacyanonitrosylferrate‐Modified Carbon Ceramic Electrode: Application to Electrocatalytic Oxidation and Amperometric Detection of L‐Cysteine

The sol‐gel technique was used to construct tin pentacyanonitrosylferrate (SnPCNF) modified composite carbon ceramic electrode (CCE). This involves two steps: construction of CCE containing metallic Sn powder and then electrochemical creating of SnPCNF on the surface of CCE. The SnPCNF modified CCE (SnPCNFlCCE) was characterized by energy‐dispersive X‐ray (EDX), FTIR and cyclic voltammetry (CV) techniques. The SnPCNF film showed electrocatalytic activity toward the oxidation of L ‐cysteine. A linear calibration plot was obtained over the L ‐cysteine concentration range 1–51 μM using chronoamperometry. L ‐cysteine was determined amperometrically at the surface of this modified electrode. The detection limit (for a signal to noise of 3) and sensitivity were found to be 0.62 μM and 126 μA/mM, respectively.     

Amperometric L‐cysteine Sensor Using a Gold Electrode Modified with Thiolated Catechol

A thiolated catechol (CA) consisting of 1,6‐Hexanedithiol (HDT) and CA was modified on a gold (Au) electrode to obtain an amperometric L‐cysteine sensor with detection limit of 60.6 nM. The preparation of thiolated CA was conducted via a thiol addition between HDT and electro‐oxidized CA (EOCA). Briefly, the thiol addition reaction was accomplished by potential cycling of HDT/Au electrode in 0.1 M phosphate buffer (PB, pH 7.2) containing CA, and an EOCA‐HDT/Au electrode was produced. The obtained EOCA‐HDT/Au electrode exhibits a pair of well‐defined redox peaks (at 0.22/0.10 V) of o‐quinone moiety, which effectively mediates the oxidation of L‐cysteine in a 0.1 M PB (pH 7.2), with an over‐potential decrease by ca. 0.12 V (versus bare Au electrode). Electrochemical quartz crystal microbalance, cyclic voltammetry and surface‐enhanced Raman spectra were used to study relevant processes and/or film properties. The amperometric L‐cysteine sensor has good anti‐interferent ability and reproducibility. It also has acceptable recovery for detection of L‐cysteine in urine samples.     

Preparation and Photophysical and Photoelectrochemical Properties of a Covalently Fixed Porphyrin–Chemically Converted Graphene Composite

Chemically converted graphene (CCG) covalently linked with porphyrins has been prepared by a Suzuki coupling reaction between iodophenyl‐functionalized CCG and porphyrin boronic ester. The covalently linked CCG–porphyrin composite was designed to possess a short, rigid phenylene spacer between the porphyrin and the CCG. The composite material formed stable dispersions in DMF and the structure was characterized by spectroscopic, thermal, and microscopic measurements. In steady‐state photoluminescence spectra, the emission from the porphyrin linked to the CCG was quenched strongly relative to that of the porphyrin reference. Fluorescence lifetime and femtosecond transient absorption measurements of the porphyrin‐linked CCG revealed a short‐lived porphyrin singlet excited state (38 ps) without yielding the porphyrin radical cation, thereby substantiating the occurrence of energy transfer from the porphyrin excited state to the CCG and subsequent rapid decay of the CCG excited state to the ground state. Consistently, the photocurrent action spectrum of a photoelectrochemical device with a SnO₂ electrode coated with the porphyrin‐linked CCG exhibited no photocurrent response from the porphyrin absorption. The results obtained here provide deep insight into the interaction between graphenes and π‐conjugated systems in the excited and ground states.     

Luminescence Enhancement based Sensing of L‐Cysteine by Doped Quantum Dots

The interaction of a presynthesized orange emitting Mn²⁺‐doped ZnS quantum dots (QDs) with L‐Cysteine (L?Cys) led to enhance emission intensity (at 596 nm) and quantum yield (QY). Importantly, the Mn²⁺‐doped ZnS QDs exhibited high sensitivity towards L?Cys, with a limit of detection of 0.4±0.02 μM (in the linear range of 3.3–13.3 μM) and high selectivity in presence of interfering amino acids and metal ions. The association constant of L?Cys was determined to be 0.36×10⁵ M^?1. The amplified passivation of the surface of Mn²⁺‐doped ZnS QDs following the incorporation and binding of L?Cys is accounted for the enhancement in their luminescence features. Moreover, the luminescence enhancement‐based detection will bring newer dimension towards sensing application.     

α‐Fe2O3 Film with Highly Photoactivity for Non‐enzymatic Photoelectrochemical Detection of Glucose

A non‐enzyme photoelectrochemical (PEC) glucose sensor based on α‐Fe₂O₃ film is investigated. The α‐Fe₂O₃ film was fabricated via a simple spin coating method. The proposed glucose sensor exhibits good selectivity, a fast response time of <5 s, a linear range of 0.05 to 6.0 mM, sensitivity of 17.23 μA mM^?1 cm^?2 and a detection limit of 0.05 μM. Meanwhile, the excellent performances of the α‐Fe₂O₃ sensor were obtained in reproducibility and the long‐term stability under ambient condition. The linear amperometric response of the sensor covers the glucose levels in physiological and clinical for diabetic patients. Therefore, this non‐enzyme PEC sensor based on α‐Fe₂O₃ film has a great potential application in the development of glucose sensors.     

A Novel L‐Cysteine Electrochemical Sensor Using Sulfonated Graphene‐poly(3,4‐Ethylenedioxythiophene) Composite Film Decorated with Gold Nanoparticles

By exploiting the electrostatic interaction between positively charged 3,4‐ethylenedioxythiophene cation radicals and negatively charged sulfonated graphene (SG) sheets, we prepared a poly(3,4‐ethylenedioxythiophene)‐sulfonated graphene (SG‐PEDOT) composite film by a one‐step electrochemical process. The composite was further decorated with gold nanoparticles (AuNPs) and employed as an electrode material for the detection of L ‐cysteine (Cys). The SG‐PEDOT composite film is shown to provide a rough surface for the electrodeposition of AuNPs and to improve substrate accessibility and interaction with Cys. Moreover, the AuNPs‐decorated composite exhibits better electrocatalytic performance than that of a SG‐PEDOT composite only. Under optimum experimental conditions, the amperometric current of the sensor is linearly related to the concentration of Cys in the 0.1 to 382 µM range, and the detection limit is 0.02 µM (at S/N=3). The modified electrode displays favorable selectivity, good stability and high reproducibility. The method was successfully applied to the detection of Cys in spiked human urine.     

L‐Cysteine Voltammetry at a Carbon Paste Electrode Bulk‐Modified with Ferrocenedicarboxylic Acid

The electrochemical behavior of L ‐cysteine studied at the surface of ferrocenedicarboxylic acid modified carbon paste electrode (FDCMCPE) in aqueous media using cyclic voltammetry, differential pulse voltammetry and double potential step chronoamperometry. It has been found that under optimum condition (pH 8.00) in cyclic voltammetry, the oxidation of L ‐cysteine occurs at a potential about 200 mV less positive than that of an unmodified carbon paste electrode. The kinetic parameters such as electron transfer coefficient, α, and catalytic reaction rate constant, k_h were also determined using electrochemical approaches. The electrocatalytic oxidation peak current of L ‐cysteine showed a linear dependent on the L ‐cysteine concentration and linear analytical curves were obtained in the ranges of 3.0×10^?5 M–2.2×10^?3 M and 1.5×10^?5 M–3.2×10^?3 M of L ‐cysteine concentration with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods respectively. The detection limits (3σ) were determined as 2.6×10^?5 M and 1.4×10^?6 M by CV and DPV methods.     

Cobalt Phthalocyanine‐Based Molecular Materials for the Electrocatalysis and Electroanalysis of 2‐Mercaptoethanol, 2‐Mercaptoethanesulfonic Acid,Reduced Glutathione and L‐Cysteine

We have investigated the electrocatalytic activity of cobalt tetra‐aminophthalocyanine (CoTAPc) for the one‐electron oxidation of thiols of various sizes, namely 2‐mercaptoethanol, 2‐mercaptoethanesulfonic acid, reduced glutathione and L ‐cysteine, using adsorbed monomeric CoTAPc and electropolymerized poly‐CoTAPc films of different thickness on a vitreous carbon electrode. Our results show that the electrocatalytic activity of poly‐CoTAPc films towards the oxidation of the thiols increases slightly with the thickness of the film, but remains similar to that of the adsorbed monomeric CoTAPc. The higher stability of the electropolymerized poly‐CoTAPc films makes them attractive for applications in the activation and/or the detection of thiols. We have assessed this approach by designing ultra‐micro‐carbon‐fiber electrodes, coated with poly‐CoTAPc, and combining their use with different electrochemical techniques (cyclic voltammetry, differential pulse voltammetry and differential normal pulse amperometry) for the electroanalysis of the examined thiols.     

Label‐Free Detection of MicroRNA: Two‐Step Signal Enhancement with a Hairpin‐Probe‐Based Graphene Fluorescence Switch and Isothermal Amplification

A label‐free approach with multiple enhancement of the signal for microRNA detection has been introduced. The key idea of this strategy is achieved by taking advantage of a novel graphene oxide (GO)/intercalating dye based fluorescent hairpin probe (HP) and an isothermal polymerization reaction. In this paper, we used microRNA‐21 (mir‐21) as the target to examine the desirable properties of this assay. When the target, as a “trigger”, was hybridized with the HP and caused a conformation change, an efficient isothermal polymerization reaction was activated to achieve the first step of the “signal” amplification. After incubation with the platform of GO/intercalating dye, the formed complex of DNA interacted with the high‐affinity dye and then detached from the surface of the GO, a process that was accompanied by distinguishable fluorescence recovery. Further signal enhancement has been accomplished by a mass of intercalating dye inserting into the minor groove of the long duplex replication product. Due to the efficient and multiple amplification steps, this approach exerted a substantial enhancement in sensitivity and could be used for rapid and selective detection of Mir‐21 at attomole levels. Proof‐of‐concept evidence has been provided for the proposed cost‐effective strategy; thus, this strategy could expand the application of GO‐material‐based bioanalysis for nucleic acid studies.