Nitrogen‐doped Carbon–CoOx Nanohybrids: A Precious Metal Free Cathode that Exceeds 1.0 W cm−2 Peak Power and 100 h Life in Anion‐Exchange Membrane Fuel Cells

Efficient and durable nonprecious metal electrocatalysts for the oxygen reduction (ORR) are highly desirable for several electrochemical devices, including anion exchange membrane fuel cells (AEMFCs). Here, a 2D planar electrocatalyst with CoO_x embedded in nitrogen‐doped graphitic carbon (N‐C‐CoO_x) was created through the direct pyrolysis of a metal–organic complex with a NaCl template. The N‐C‐CoO_x catalyst showed high ORR activity, indicated by excellent half‐wave (0.84 V vs. RHE) and onset (1.01 V vs. RHE) potentials. This high intrinsic activity was also observed in operating AEMFCs where the kinetic current was 100 mA cm^?2 at 0.85 V. When paired with a radiation‐grafted ETFE powder ionomer, the N‐C‐CoO_x AEMFC cathode was able to achieve extremely high peak power density (1.05 W cm^?2) and mass transport limited current (3 A cm^?2) for a precious metal free electrode. The N‐C‐CoO_x cathode also showed good stability over 100 hours of operation with a voltage decay of only 15 % at 600 mA cm^?2 under H₂/air (CO₂‐free) reacting gas feeds. The N‐C‐CoO_x cathode catalyst was also paired with a very low loading PtRu/C anode catalyst, to create AEMFCs with a total PGM loading of only 0.10 mg_Pt‐Ru cm^?2 capable of achieving 7.4 W mg^?1_PGM as well as supporting a current of 0.7 A cm^?2 at 0.6 V with H₂/air (CO₂ free)—creating a cell that was able to meet the 2019 U.S. Department of Energy initial performance target of 0.6 V at 0.6 A cm^?2 under H₂/air with a PGM loading <0.125 mg cm^?2 with AEMFCs for the first time.     

Large‐scale Two‐dimensional MoSx Catalyst Prepared under Mild Conditions for Enhancing Electrocatalytic Hydrogen Evolution Reaction

As an electrocatalyst with abundant resources and great potential, molybdenum disulfide is regarded as one of the most likely alternatives to expensive noble‐metals catalysts. However, it is still a challenge to achieve large scale production of few‐layer MoS₂ with enhancing activity of electrocatalytic hydrogen reaction at ambient conditions. Herein, we developed a simple environmentally friendly two‐step method, which included intercalation reaction and a subsequent electrochemical reduction reaction for mass preparation of defect‐rich desulfurized MoS_x (D?MoS_x) nanosheets with plentiful sulfur vacancies. The ratio of sulfur‐molybdenum atoms can be adjusted from 2 : 1 to 1.4 : 1 by regulating the desulfurization voltage. It was found that the HER catalytic activity of the D?MoS_x was enhanced compared with that of pristine MoS₂ (P?MoS₂), the current density of D?MoS_x (desulfurization at ?1.0 V) at ?0.3 V versus RHE was about 169% of the P?MoS₂, and the Tafel slope decreased to 136 mV dec^?1. This method can be widely applied to large‐scale preparation of other two‐dimensional materials.     

In Situ Reconstruction of a Hierarchical Sn‐Cu/SnOx Core/Shell Catalyst for High‐Performance CO2 Electroreduction

The electrochemical CO₂ reduction reaction (CO₂RR) to give C₁ (formate and CO) products is one of the most techno‐economically achievable strategies for alleviating CO₂ emissions. Now, it is demonstrated that the SnO_x shell in Sn_2.7Cu catalyst with a hierarchical Sn‐Cu core can be reconstructed in situ under cathodic potentials of CO₂RR. The resulting Sn_2.7Cu catalyst achieves a high current density of 406.7±14.4 mA cm^?2 with C₁ Faradaic efficiency of 98.0±0.9 % at ?0.70 V vs. RHE, and remains stable at 243.1±19.2 mA cm^?2 with a C₁ Faradaic efficiency of 99.0±0.5 % for 40 h at ?0.55 V vs. RHE. DFT calculations indicate that the reconstructed Sn/SnO_x interface facilitates formic acid production by optimizing binding of the reaction intermediate HCOO* while promotes Faradaic efficiency of C₁ products by suppressing the competitive hydrogen evolution reaction, resulting in high Faradaic efficiency, current density, and stability of CO₂RR at low overpotentials.     

Sulfur‐Modified Oxygen Vacancies in Iron–Cobalt Oxide Nanosheets: Enabling Extremely High Activity of the Oxygen Evolution Reaction to Achieve the Industrial Water Splitting Benchmark

The oxygen vacancies of defective iron–cobalt oxide (FeCoO_x‐Vo) nanosheets are modified by the homogeneously distributed sulfur (S) atoms. S atoms can not only effectively stabilize oxygen vacancies (Vo), but also form the Co?S coordination with Co active site in the Vo, which can modulate the electronic structure of the active site, enabling FeCoO_x‐Vo‐S to exhibit much superior OER activity. FeCoO_x‐Vo‐S exhibits a mass activity of 2440.0 A g^?1 at 1.5 V vs. RHE in 1.0 m KOH, 25.4 times higher than that of RuO₂. The Tafel slope is as low as 21.0 mV dec^?1, indicative of its excellent charge transfer rate. When FeCoO_x‐Vo‐S (anode catalyst) is paired with the defective CoP₃/Ni₂P (cathode catalyst) for overall water splitting, current densities of as high as 249.0 mA cm^?2 and 406.0 mA cm^?2 at a cell voltage of 2.0 V and 2.3 V, respectively, can be achieved.     

Fe2O3‐N‐doped Honeycomb‐like Porous Carbon Derived from Nature Silk Sericin as Electrocatalysts for Oxygen Evolution Reaction

A facile method is reported to form a honeycomb‐like porous nanomaterial by intercalation of iron nitrate using nature silk sericin (SS) as nitrogen and carbon source. A series of Fe₂O₃ nanoparticles anchored on Fe₂O₃‐N‐doped graphite carbon electrocatalysts (SS‐Fe) were synthesized, exhibits well‐defined pore structure and excellent oxygen evolution reaction (OER) catalytic activities. Among these materials, SS‐Fe‐0.5 shows the best performance, the overpotential of SS‐Fe‐0.5 at 10 mA · cm^–2 is 440 mV (vs. RHE) and the Tafel slope is only 68 mV · dec^–1. The results indicate that it is promising to the preparation of carbon catalyst materials using natural, renewable and abundant resources for electrocatalysis.     

Tweaking Nickel with Minimal Silver in a Heterogeneous Alloy of Decahedral Geometry to Deliver Platinum‐like Hydrogen Evolution Activity

Five‐fold intertwined Ag_xNi_1?x (x=0.01–0.25) heterogeneous alloy nanocrystal (NC) catalysts, prepared through unique reagent combinations, are presented. With only ca. 5 at % Ag (AgNi‐5), Pt‐like activity has been achieved at pH 14. To reach a current density of 10 mA cm^?2 the extremely stable AgNi‐5 requires an overpotential of 24.0±1.2 mV as compared to 20.1±0.8 mV for 20 % Pt/C, both with equal catalyst loading of 1.32 mg cm^?2. The turnover frequency (TOF) is as high as 2.1 H₂ s^?1 at 50 mV (vs. RHE). Site‐specific elemental analyses show the Ag:Ni compositional variation, where the apex and edges of the decahedra are Ag‐rich, thereby exposing Ni onto the faces to achieve maximum charge transport for an exceptional pH universal HER activity. DFT calculations elucidate the relative H‐atom adsorption capability of the Ni centers as a function of their proximity to Ag atom.     

Ultrathin,Porous and Oxygen Vacancies‐Enriched Ag/WO3−x Heterostructures for Electrocatalytic Hydrogen Evolution

Exploring advanced electrocatalysts for electrocatalytic hydrogen evolution is highly desired but remains a challenge due to the lack of an efficient preparation method and reasonable structural design. Herein, we deliberately designed novel Ag/WO_3?x heterostructures through a supercritical CO₂‐assisted exfoliation‐oxidation route and the subsequent loading of Ag nanoparticles. The ultrathin and oxygen vacancies‐enriched WO_3?x nanosheets are ideal substrates for loading Ag nanoparticles, which can largely increase the active site density and improve electron transport. Besides, the resultant WO_3?x nanosheets with porous structure can form during the electrochemical cycling process induced by an electric field. As a result, the exquisite Ag/WO_3?x heterostructures show an enhanced hydrogen evolution reaction (HER) activity with a low onset overpotential of ≈30 mV, a small Tafel slope of ≈40 mV dec^?1 at 10 mA cm^?2, and as well as long‐term durability. This work sheds light on material design and preparation, and even opens up an avenue for the development of high‐efficiency electrocatalysts.     

Iridium‐Based Cubic Nanocages with 1.1‐nm‐Thick Walls: A Highly Efficient and Durable Electrocatalyst for Water Oxidation in an Acidic Medium

We report a highly active and durable water oxidation electrocatalyst based on cubic nanocages with a composition of Ir₄₄Pd₁₀, together with well‐defined {100} facets and porous walls of roughly 1.1 nm in thickness. Such nanocages substantially outperform all the water oxidation electrocatalysts reported in literature, with an overpotential of only 226 mV for reaching 10 mA cm^?2_geo at a loading of Ir as low as 12.5 μg_Ir cm^?2 on the electrode in acidic media. When benchmarked against a commercial Ir/C electrocatalyst at 250 mV of overpotential, such a nanocage‐based catalyst not only shows enhancements (18.1‐ and 26.2‐fold, respectively) in terms of mass (1.99 A mg^?1_Ir) and specific (3.93 mA cm^?2_Ir) activities, but also greatly enhanced durability. The enhancements can be attributed to a combination of multiple merits, including a high utilization efficiency of Ir atoms and an open structure beneficial to the electrochemical oxidation of Ir to the active form of IrO_x.     

Interface Engineering of MoS2/Ni3S2 Heterostructures for Highly Enhanced Electrochemical Overall‐Water‐Splitting Activity

To achieve sustainable production of H₂ fuel through water splitting, low‐cost electrocatalysts for the hydrogen‐evolution reaction (HER) and the oxygen‐evolution reaction (OER) are required to replace Pt and IrO₂ catalysts. Herein, for the first time, we present the interface engineering of novel MoS₂/Ni₃S₂ heterostructures, in which abundant interfaces are formed. For OER, such MoS₂/Ni₃S₂ heterostructures show an extremely low overpotential of ca. 218 mV at 10 mA cm^?2, which is superior to that of the state‐of‐the‐art OER electrocatalysts. Using MoS₂/Ni₃S₂ heterostructures as bifunctional electrocatalysts, an alkali electrolyzer delivers a current density of 10 mA cm^?2 at a very low cell voltage of ca. 1.56 V. In combination with DFT calculations, this study demonstrates that the constructed interfaces synergistically favor the chemisorption of hydrogen and oxygen‐containing intermediates, thus accelerating the overall electrochemical water splitting.     

Template‐Free Preparation of Volvox‐like CdxZn1−xS Nanospheres with Cubic Phase for Efficient Photocatalytic Hydrogen Production

Volvox‐like Cd_xZn_1?xS solid solutions with a cubic zinc blend structure were synthesized through a template‐free ethylene glycol process. Cd(Ac)₂ ? 2 H₂O, Zn(Ac)₂ ? 2 H₂O, and thiourea are used as the starting materials and dissolved in ethylene glycol. These reaction precursors and solvent not only contributed to control over the formation of the volvox‐like spherical geometry, but also exerted vigorous domination for existence of cubic‐phase Cd_xZn_1?xS nanostructures. As‐prepared volvox‐like Cd_xZn_1?xS nanospheres have a diameter of around 100 nm with extensional shells. These samples show excellent photocatalytic H₂ evolution activity from water splitting under visible‐light irradiation without any cocatalyst or scaffolding, owing to their tunable band gap, cubic zinc blend structure, and unique hierarchical porous structure with a high surface area (as high as 95.2 m² g^?1).     

Hydrogen Production by Water Dissociation in Surface‐Modified BaCoxFeyZr1−x−yO3−δ Hollow‐Fiber Membrane Reactor with Improved Oxygen Permeation

A porous perovskite BaCo_xFe_yZr_0.9?x?yPd_0.1O_3?δ (BCFZ‐Pd) coating was deposited onto the outer surface of a BaCo_xFe_yZr_1?x?yO_3?δ (BCFZ) perovskite hollow‐fiber membrane. The surface morphology of the modified BCFZ fiber was characterized by scanning electron microscopy (SEM), indicating the formation of a BCFZ‐Pd porous layer on the outer surface of a dense BCFZ hollow‐fiber membrane. The oxygen permeation flux of the BCFZ membrane with a BCFZ‐Pd porous layer increased 3.5 times more than that of the blank BCFZ membrane when feeding reactive CH₄ onto the permeation side of the membrane. The blank BCFZ membrane and surface‐modified BCFZ membrane were used as reactors to shift the equilibrium of thermal water dissociation for hydrogen production because they allow the selective removal of the produced oxygen from the water dissociation system. It was found that the hydrogen production rate increased from 0.7 to 2.1 mL H₂ min^?1 cm^?2 at 950 °C after depositing a BCFZ‐Pd porous layer onto the BCFZ membrane.     

Boosting Electrochemical Reduction of CO2 at a Low Overpotential by Amorphous Ag‐Bi‐S‐O Decorated Bi0 Nanocrystals

Bimetal‐S‐O composites have been rarely researched in electrochemical reduction of CO₂. Now, an amorphous Ag‐Bi‐S‐O decorated Bi⁰ catalyst derived from Ag_0.95BiS_0.75O_3.1 nanorods by electrochemical pre‐treatment was used for catalyzing eCO₂RR, which exhibited a formate FE of 94.3 % with a formate partial current density of 12.52 mA cm^?2 at an overpotential of only 450 mV. This superior performance was attributed to the attached amorphous Ag‐Bi‐S‐O substance. S could be retained in the amorphous region after electrochemical pre‐treatment only in samples derived from metal‐S‐O composites, and it would greatly enhance the formate selectivity by accelerating the dissociation of H₂O. The existence of Ag would increase the current density, resulting in a higher local pH, which made the role of S in activating H₂O more significantly and suppressed H₂ evolution more effectively, thus endowing the catalyst with a higher formate FE at low overpotentials.     

2D/2D h‐BN/N‐doped MoS2 Heterostructure Catalyst with Enhanced Peroxidase‐like Performance for Visual Colorimetric Determination of H2O2

Recently, nanozymes have attracted extensive attention because of their advantages of combining nanomaterials with enzymes. Herein, hexagonal boron nitride (h‐BN) and nitride‐doped molybdenum disulfide (N?MoS₂) nano‐composites (h‐BN/N?MoS₂) were synthesized by facile and cost‐effective liquid exfoliation with a solvothermal method in nontoxic ethanol solution. The results show that h‐BN, as a co‐catalyst, can not only dope into the lattice of MoS₂ but also form a heterogeneous structure with MoS₂NSs. It expanded the layer spacing and specific surface area of MoS₂NSs, which was beneficial to the contact between the catalyst and the substrate, and resulted in a synergistic enhancement of the catalytic activity of hydrogen peroxide (H₂O₂) with MoS₂. A colorimetric determination platform of h‐BN/N?MoS₂‐TMB‐H₂O₂ was constructed. It exhibited a wide linear range of 1–1000 μM with a low limit of detection (LOD) of 0.4 μM under optimal conditions, high sensitivity and stability, as well as good reliability (99.4–110.0%) in practice, making the measurement system more widely applicable.1. Introduction     

Mesoporous Carbon Nanofibers Embedded with MoS2 Nanocrystals for Extraordinary Li‐Ion Storage

MoS₂ nanocrystals embedded in mesoporous carbon nanofibers are synthesized through an electrospinning process followed by calcination. The resultant nanofibers are 100–150 nm in diameter and constructed from MoS₂ nanocrystals with a lateral diameter of around 7 nm with specific surface areas of 135.9 m² g^?1. The MoS₂@C nanofibers are treated at 450 °C in H₂ and comparison samples annealed at 800 °C in N₂. The heat treatments are designed to achieve good crystallinity and desired mesoporous microstructure, resulting in enhanced electrochemical performance. The small amount of oxygen in the nanofibers annealed in H₂ contributes to obtaining a lower internal resistance, and thus, improving the conductivity. The results show that the nanofibers obtained at 450 °C in H₂ deliver an extraordinary capacity of 1022 mA h g^?1 and improved cyclic stability, with only 2.3 % capacity loss after 165 cycles at a current density of 100 mA g^?1, as well as an outstanding rate capability. The greatly improved kinetics and cycling stability of the mesoporous MoS₂@C nanofibers can be attributed to the crosslinked conductive carbon nanofibers, the large specific surface area, the good crystallinity of MoS₂, and the robust mesoporous microstructure. The resulting nanofiber electrodes, with short mass‐ and charge‐transport pathways, improved electrical conductivity, and large contact area exposed to electrolyte, permitting fast diffusional flux of Li ions, explains the improved kinetics of the interfacial charge‐transfer reaction and the diffusivity of the MoS₂@C mesoporous nanofibers. It is believed that the integration of MoS₂ nanocrystals and mesoporous carbon nanofibers may have a synergistic effect, giving a promising anode, and widening the applicability range into high performance and mass production in the Li‐ion battery market.     

Robust SnO2−x Nanoparticle‐Impregnated Carbon Nanofibers with Outstanding Electrochemical Performance for Advanced Sodium‐Ion Batteries

The sluggish sodium reaction kinetics, unstable Sn/Na₂O interface, and large volume expansion are major obstacles that impede practical applications of SnO₂‐based electrodes for sodium‐ion batteries (SIBs). Herein, we report the crafting of homogeneously confined oxygen‐vacancy‐containing SnO_2?x nanoparticles with well‐defined void space in porous carbon nanofibers (denoted SnO_2?x/C composites) that address the issues noted above for advanced SIBs. Notably, SnO_2?x/C composites can be readily exploited as the working electrode, without need for binders and conductive additives. In contrast to past work, SnO_2?x/C composites‐based SIBs show remarkable electrochemical performance, offering high reversible capacity, ultralong cyclic stability, and excellent rate capability. A discharge capacity of 565 mAh g^?1 at 1 A g^?1 is retained after 2000 cycles.     

Ethylene polymerization and copolymerization with 10‐undecen‐1‐ol using the catalyst system DADNi(NCS)2/MAO

The catalyst DADNi(NCS)₂ (DAD = (ArN?C(Me)? C(Me)?ArN); Ar = 2,6‐C₆H₃), activated by methylaluminoxane, was tested in ethylene polymerization at temperatures above 25 °C and variable Al/Ni ratio. The system was shown to be active even at 80 °C and when supported on silica. However, catalyst activity decreased. The catalyst system was also tested in ethylene and 10‐undecen‐1‐ol copolymerization at different ethylene pressures. The best activities were obtained at low polar monomer concentration (0.017 mol/L), using triisopropylaluminum (Al‐i‐Pr₃) to protect the polar monomer. The incorporation of the comonomer increased with the increase of polar monomer concentration. According to ¹³C NMR analyses, all the resulting polyethylenes were highly branched and the polar monomer incorporation decreased as ethylene pressure increased. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5199–5208, 2007     

Bis[(±)‐trans‐2‐amino­cyclo­hexyl­ammonium] tetra­thio­molybdate(VI) and trans‐cyclo­hexane‐1,4‐diammonium tetra­thio­molybdate(VI)

The structures of the title complexes, (C₆H₁₅N₂)₂[MoS₄], (I), and (C₆H₁₆N₂)[MoS₄], (II), can be described as consisting of discrete tetra­hedral [MoS₄]²⁻ dianions that are linked to the organic ammonium cations via weak hydrogen‐bonding inter­actions. The asymmetric unit of (I) consists of a single (±)‐trans‐2‐amino­cyclo­hexyl­ammonium cation in a general position and an [MoS₄]²⁻ anion located on a twofold axis, while in (II), two crystallographically independent trans‐cyclo­hexane‐1,4‐diammonium cations located on centres of inversion and one [MoS₄]²⁻ anion in a general position are found. The differing dispositions of the amine functionalities in the organic cations in the title complexes lead to different crystal packing arrangements in (I) and (II).     

Synthesis and Characterization of Novel Gold(III) Complexes of Asymmetrically Aryl‐Substituted 1,2‐Dithiolene Ligands Featuring Potential‐Controlled Spectroscopic Properties

The tetrabutylammonium (TBA⁺) salts of square‐planar monoanionic gold complexes of the unsymmetrically substituted Ar,H‐edt^2? 1,2‐dithiolene ligands (Ar,H‐edt^2?=arylethylene‐1,2‐dithiolato; Ar=phenyl ( 1 ^?), 2‐naphthyl ( 2 ^?), and 1‐pyrenyl ( 3 ^?)) were synthesized and characterized by spectroscopic and electrochemical methods and the corresponding neutral species ( 1 , 2 , and 3 , respectively) were obtained in CH₂Cl₂ solution at room temperature by diiodine oxidation. The single‐crystal X‐ray diffraction structural data collected for (TBA⁺)( 2 ^?), supported by DFT theoretical calculations, are consistent with the ene‐1,2‐dithiolate form of the ligand and the Au^III oxidation state. All complexes feature intense near‐IR absorptions (at about 1.5 μm) in their neutral states and Vis‐emitting properties in the 400–550 nm range, the energy of which is controlled by the charge of the complex in the case of the 3 ^?/ 3 couple. The spectroscopic and electrochemical features of 1 ^x? and 2 ^x? (x=0, 1), both in their cis and trans conformations, were investigated by means of DFT and time‐dependent (TD) DFT calculations.     

Methyl 4‐amino‐2,3‐dihydro‐6‐methoxy‐1,3‐dioxo‐1H‐pyrrolo[3,4‐c]pyridine‐7‐carboxylate forms hydrogen‐bonded sheets built from R22(8) and R66(42) rings

In the title compound, C₁₀H₉N₃O₅, which was formed by the reaction of 6‐amino‐2‐methoxy‐4(3H)‐pyrimidinone with di­methyl acetyl­enedi­carboxyl­ate, the mol­ecules are linked by N—H?O hydrogen bonds [N?O 2.8974 (15) and 3.0300 (15) Å, and N—H?O 165 and 174°] into planar sheets built from alternating R₂²(8) and R₆⁶(42) rings.     

High‐Performance Platinum‐Free Dye‐Sensitized Solar Cells with Molybdenum Disulfide Films as Counter Electrodes

By using a radio‐frequency sputtering method, we synthesized large‐area, uniform, and transparent molybdenum disulfide film electrodes (1, 3, 5, and 7 min) on transparent and conducting fluorine‐doped tin oxide (FTO), as ecofriendly, cost‐effective counter electrodes (CE) for dye‐sensitized solar cells (DSSCs). These CEs were used in place of the routinely used expensive platinum CEs for the catalytic reduction of a triiodide electrolyte. The structure and morphology of the MoS₂ was analyzed by using Raman spectroscopy, X‐ray diffraction, and X‐ray photoemission spectroscopy measurements and the DSSC characteristics were investigated. An unbroken film of MoS₂ was identified on the FTO crystallites from field‐emission scanning electron microscopy. Cyclic voltammetry, electrochemical impedance spectroscopy, and Tafel curve measurements reveal the promise of MoS₂ as a CE with a low charge‐transfer resistance, high electrocatalytic activity, and fast reaction kinetics for the reduction of triiodide to iodide. Finally, an optimized transparent MoS₂ CE, obtained after 5 min synthesis time, showed a high power‐conversion efficiency of 6.0 %, which comparable to the performance obtained with a Pt CE (6.6 %) when used in TiO₂‐based DSCCs, thus signifying the importance of sputtering time on DSSC performance.