Coagulated SnO2 Colloids for High‐Performance Planar Perovskite Solar Cells with Negligible Hysteresis and Improved Stability

Organic–inorganic perovskite solar cells with a planar architecture have attracted much attention due to the simple structure and easy fabrication. However, the power conversion efficiency and hysteresis behavior need to be improved for planar‐type devices where the electron transport layer is vital. SnO₂ is a promising alternative for TiO₂ as the electron transport layer owing to the high charge mobility and chemical stability, but the hysteresis issue can still remain despite the use of SnO₂. Now, a facile and effective method is presented to simultaneously tune the electronic property of SnO₂ and passivate the defects at the interface between the perovskite and SnO₂. The perovskite solar cells with ammonium chloride induced coagulated SnO₂ colloids exhibit a power conversion efficiency of 21.38 % with negligible hysteresis, compared to 18.71 % with obvious hysteresis for the reference device. The device stability can also be significantly improved.     

Interfacial Engineering for Efficient Low-Temperature Flexible Perovskite Solar Cells

Photovoltaic technology with low weight, high specific power in cold environments, and compatibility with flexible fabrication is highly desired for near-space vehicles and polar region applications. Herein, we demonstrate efficient low-temperature flexible perovskite solar cells by improving the interfacial contact between electron-transport layer (ETL) and perovskite layer. We find that the adsorbed oxygen active sites and oxygen vacancies of flexible tin oxide (SnO₂) ETL layer can be effectively decreased by incorporating a trace amount of titanium tetrachloride (TiCl₄). The effective defects elimination at the interfacial increases the electron mobility of flexible SnO₂ layer, regulates band alignment at the perovskite/SnO₂ interface, induces larger perovskite crystal growth, and improves charge collection efficiency in a complete solar cell. Correspondingly, the improved interfacial contact transforms into high-performance solar cells under one-sun illumination (AM 1.5G) with efficiencies up to 23.7 % at 218 K, which might open up a new era of application of this emerging flexible photovoltaic technology to low-temperature environments such as near-space and polar regions.     

SnO2双层电子传输层对钙钛矿太阳能电池界面电荷传输的影响

为了改善基于SnO₂电子传输层的钙钛矿太阳能电池的界面电荷传输特性和迟滞现象,我们采用低温溶液处理工艺制备了4种不同类型的SnO₂电子传输层用于钙钛矿太阳能电池,包括由SnCl₄·5H₂O溶胶-凝胶层(Cl₄-SnO₂)、SnCl₂·2H₂O溶胶-凝胶层(Cl₂-SnO₂)和SnO₂纳米颗粒层(NP-SnO₂)与SnO₂胶体层(Col-SnO₂)两两相互作用形成的同质结SnO₂双层电子传输层和Col-SnO₂单层电子传输层;并系统研究了不同SnO₂双层电子传输层对器件光电性能和迟滞现象的影响。通过扫描电镜(SEM)、X射线衍射(XRD)、稳态光致发光(PL)、电化学阻抗(EIS)和稳定性测试等表征证实,在Col-SnO...     

Enhanced Lifetime and Photostability with Low‐Temperature Mesoporous ZnTiO3/Compact SnO2 Electrodes in Perovskite Solar Cells

Perovskite solar cells (PSCs) with power conversion efficiencies (PCEs) of 25 % mainly have SnO₂ or TiO₂ as electron‐transporting layers (ETLs). Now, zinc titanate (ZnTiO₃, ZTO) is proposed as mesoporous ETLs owing to its weak photo‐effect, excellent carrier extraction, and transfer properties. Uniform mesoporous films were obtained by spinning coating the ZTO ink and annealed below 150 °C. Photovoltaic devices based on Cs_0.05FA_0.81MA_0.14PbI_2.55B_r0.45 perovskite sandwiched between SnO₂‐mesorporous ZTO electrode and Spiro‐OMeTAD layer achieved the PCE of 20.5 %. The PSCs retained more than 95 % of their original efficiency after 100 days lifetime test without being encapsulated. Additionally, the PSCs retained over 95 % of the initial performance when subjected at the maximum power point voltage for 120 h under AM 1.5 G illumination (100 mW cm^?2), demonstrating superior working stability. The application of ZTO provides a better choice for ETLs of PSCs.     

Inside Back Cover: Directional Transformation of Heterometallic Oxo Clusters: A New Approach to Prepare Wide-Bandgap Cathode Interlayers for Perovskite Solar Cells (Angew. Chem. Int. Ed. 17/2023)

Typical wide-band gap cathode interlayer materials are difficulty in reducing interface recombination without limiting charge transport in perovskite solar cells (PSCs). Here, a lead-doped titanium-oxo cluster protected by S-containing ligands is introduced at the interface of perovskite and SnO₂. By in situ heating, the cluster is transformed into PbSO₄-PbTi₃O₇ heterostructure. The oxygen atoms from sulfate ion in heterostructure connect with iodine from perovskite to boost interfacial electron extraction and reduce charge recombination. While the yielded metallic interface between PbSO₄ and PbTi₃O₇ promotes the electron transport across the interface. Finally, an efficiency as high as 24.2 % for the modified PSC is obtained. The heterostructure well-stabilize the interface of perovskite and SnO₂, to greatly improve the device stability. This work provides a novel strategy to prepare wide-band gap cathode interlayer by directional transformation of heterometallic oxo clusters.     

Unconventional Route to Oxygen‐Vacancy‐Enabled Highly Efficient Electron Extraction and Transport in Perovskite Solar Cells

The ability to effectively transfer photoexcited electrons and holes is an important endeavor toward achieving high‐efficiency solar energy conversion. Now, a simple yet robust acid‐treatment strategy is used to judiciously create an amorphous TiO₂ buffer layer intimately situated on the anatase TiO₂ surface as an electron‐transport layer (ETL) for efficient electron transport. The facile acid treatment is capable of weakening the bonding of zigzag octahedral chains in anatase TiO₂, thereby shortening staggered octahedron chains to form an amorphous buffer layer on the anatase TiO₂ surface. Such amorphous TiO₂‐coated ETL possesses an increased electron density owing to the presence of oxygen vacancies, leading to efficient electron transfer from perovskite to TiO₂. Compared to pristine TiO₂‐based devices, the perovskite solar cells (PSCs) with acid‐treated TiO₂ ETL exhibit an enhanced short‐circuit current and power conversion efficiency.     

Designing a Perylene Diimide/Fullerene Hybrid as Effective Electron Transporting Material in Inverted Perovskite Solar Cells with Enhanced Efficiency and Stability

Electron transport materials (ETM) play an important role in the improvement of efficiency and stability for inverted perovskite solar cells (PSCs). This work reports an efficient ETM, named PDI‐C₆₀, by the combination of perylene diimide (PDI) and fullerene. Compared to the traditional PCBM, this strategy endows PDI‐C₆₀ with slightly shallower energy level and higher electron mobility. As a result, the device based on PDI‐C₆₀ as electron transport layer (ETL) achieves high power conversion efficiency (PCE) of 18.6 %, which is significantly higher than those of the control devices of PCBM (16.6 %) and PDI (13.8 %). The high PCE of the PDI‐C₆₀‐based device can be attributed to the more matching energy level with the perovskite, more efficient charge extraction, transport, and reduced recombination rate. To the best of our knowledge, the PCE of 18.6 % is the highest value in the PSCs using PDI derivatives as ETLs. Moreover, the device with PDI‐C₆₀ as ETL exhibits better device stability due to the stronger hydrophobic properties of PDI‐C₆₀. The strategy using the PDI/fullerene hybrid provides insights for future molecular design of the efficient ETM for the inverted PSCs.     

Inkjet Printing and Instant Chemical Transformation of a CH3NH3PbI3/Nanocarbon Electrode and Interface for Planar Perovskite Solar Cells

A planar perovskite solar cell that incorporates a nanocarbon hole‐extraction layer is demonstrated for the first time by an inkjet printing technique with a precisely controlled pattern and interface. By designing the carbon plus CH₃NH₃I ink to transform PbI₂ in situ to CH₃NH₃PbI₃, an interpenetrating seamless interface between the CH₃NH₃PbI₃ active layer and the carbon hole‐extraction electrode was instantly constructed, with a markedly reduced charge recombination compared to that with the carbon ink alone. As a result, a considerably higher power conversion efficiency up to 11.60 % was delivered by the corresponding solar cell. This method provides a major step towards the fabrication of low‐cost, large‐scale, metal‐electrode‐free but still highly efficient perovskite solar cells.     

A Rutile TiO2 Electron Transport Layer for the Enhancement of Charge Collection for Efficient Perovskite Solar Cells

Interfacial charge collection efficiency has demonstrated significant effects on the power conversion efficiency (PCE) of perovskite solar cells (PSCs). Herein, crystalline phase‐dependent charge collection is investigated by using rutile and anatase TiO₂ electron transport layer (ETL) to fabricate PSCs. The results show that rutile TiO₂ ETL enhances the extraction and transportation of electrons to FTO and reduces the recombination, thanks to its better conductivity and improved interface with the CH₃NH₃PbI₃ (MAPbI₃) layer. Moreover, this may be also attributed to the fact that rutile TiO₂ has better match with perovskite grains, and less trap density. As a result, comparing with anatase TiO₂ ETL, MAPbI₃ PSCs with rutile TiO₂ ETL delivers significantly enhanced performance with a champion PCE of 20.9 % and a large open circuit voltage (V_OC) of 1.17 V.     

Compact layer influence on hysteresis effect in organic–inorganic hybrid perovskite solar cells

Organic–inorganic hybrid perovskite solar cells have attracted great attention due to their high power conversion efficiency and low cost. However, an anomalous hysteresis effect exists in the perovskite solar cells, especially with TiO₂ as the n-type electron extraction layer. In this communication, we prepare two kinds of TiO₂ compact layers using Atomic Layer Deposition (ALD) and Spin-Coating (SC) methods and compare their influences on the hysteresis effect. By efficiency comparison and AC impedance spectroscopy study, we find that the thickness and morphology of compact layer have a significant influence on the hysteresis effect. Compared to the SC approach, the ALD prepared compact layer is ultra-thin with uniform morphology and shows small interfacial capacitance and large recombination resistance, meaning reduced interfacial charge accumulation and accelerated electron transport, which would relieve the hysteresis effect.     

Low-Cost Hydroxyacid Potassium Synergists as an Efficient In Situ Defect Passivator for High Performance Tin-Oxide-Based Perovskite Solar Cells

Perovskite solar cells (PSCs) based on SnO₂ electron transport layers have attracted extensive research due to their compelling photovoltaic performance. Herein, we presented an in situ passivation of SnO₂ with low-cost hydroxyacid potassium synergist during deposition to optimize the interface carrier extraction and transport for high power conversion efficiency (PCE) and stabilities of PSCs. The orbital overlap of the carboxyl oxygen with the Sn atom alongwith the homogenous nano-particle deposition effectively suppresses the interfacial defects and releases the internal residual strains in the perovskite. Accordingly, a PCE of 24.91 % with a fill factor (FF) up to 0.852 is obtained for in situ passivated devices, which is one of the highest values for SnO₂-based PSCs. Moreover, the unencapsulated device maintained 80 % of its initial PCE at 80 °C over 600 h, 100 % PCE at ambient conditions for 1300 h, and 98 % after one week maximum power point tracking (MPPT) under continuous AM1.5G illumination.     

Steric Mixed‐Cation 2D Perovskite as a Methylammonium Locker to Stabilize MAPbI3

The reduced dimension perovskite including 2D perovskites are one of the most promising strategies to stabilize lead halide perovskite. A mixed‐cation 2D perovskite based on a steric phenyltrimethylammonium (PTA) cation is presented. The PTA‐MA mixed‐cation 2D perovskite of PTAMAPbI₄ can be formed on the surface of MAPbI₃ (PTAI‐MAPbI₃) by controllable PTAI intercalation by either spin coating or soaking. The PTAMAPbI₄ capping layer can not only passivate PTAI‐MAPbI₃ perovskite but also act as MA⁺ locker to inhibit MAI extraction and significantly enhance the stability. The highly stable PTAI‐MAPbI₃ based perovskite solar cells exhibit a reproducible photovoltaic performance with a champion PCE of 21.16 %. Such unencapsulated devices retain 93 % of initial efficiency after 500 h continuous illumination. This steric mixed‐cation 2D perovskite as MA⁺ locker to stabilize the MAPbI₃ is a promising strategy to design stable and high‐performance hybrid lead halide perovskites.     

Low‐Energy Electron‐Induced Transformations in Organolead Halide Perovskite

Methylammonium lead iodide perovskite (MAPbI₃), a prototype material for potentially high‐efficient and low‐cost organic–inorganic hybrid perovskite solar cells, has been investigated intensively in recent years. A study of low‐energy electron‐induced transformations in MAPbI₃ is presented, performed by combining controlled electron‐impact irradiation with X‐ray photoelectron spectroscopy and scanning electron microscopy. Changes were observed in both the elemental composition and the morphology of irradiated MAPbI₃ thin films as a function of the electron fluence for incident energies from 4.5 to 60 eV. The results show that low‐energy electrons can affect structural and chemical properties of MAPbI₃. It is proposed that the transformations are triggered by the interactions with the organic part of the material (methylammonium), resulting in the MAPbI₃ decomposition and aggregation of the hydrocarbon layer.     

Limiting Perovskite Solar Cell Performance by Heterogeneous Carrier Extraction

Although the power conversion efficiency of perovskite solar cells has improved rapidly, a rational path for further improvement remains unclear. The effect of large morphological heterogeneity of polycrystalline perovskite films on their device performance by photoluminescence (PL) microscopy has now been studied. Contrary to the common belief on the deleterious effect of morphological heterogeneity on carrier lifetimes and diffusivities, in neat CH₃NH₃PbI₃(Cl) polycrystalline perovskite films, the local (intra‐grain) carrier diffusivities in different grains are all surprisingly high (1.5 to 3.3 cm² s^?1; comparable to bulk single‐crystals), and the local carrier lifetimes are long (ca. 200 ns) and surprisingly homogenous among grains, and uniform across grain boundary and interior. However, there is a large heterogeneity of carrier extraction efficiency at the perovskite grain–electrode interface. Improving homogeneity at perovskite grain–electrode contacts is thus a promising direction for improving the performance of perovskite thin‐film solar cells.     

Large area,waterproof, air stable and cost effective efficient perovskite solar cells through modified carbon hole extraction layer

The conventional unstable and expensive hole transporting materials (HTM) has been replaced by cost effective modified carbon hole extraction layer. Herein, we demonstrated a new recipe toward air stable and waterproof modified carbon hole extraction layer for efficient perovskite solar cells (PSCs). The commercial available carbon ink modified with methylammonium lead iodide (MAI) has been used as hole extraction layer for ambipolar perovskite solar cells. The fabricated optimized perovskite solar cell having Glass/FTO/mp-TiO₂/MAPbI_3-xCl_x/carbon + MAI/Carbon configuration exhibited η = 13.87% power conversion efficiency (PCE) with open circuit voltage (V_OC) 0.997 V, current density (J_SC) = 21.41 mAcm^?2 and fill factor (FF) 0.65. Furthermore, the air stability were tested at room temperature in open atmosphere. The water proof stability was tested under water flushing. Our results revealed that, although our carbon based devices show lower PCE (η = 13.87%) compared to spiro-MeOTAD HTM (η = 15%), the fabricated PSCs could even retain >90% after water exposure >20 times and ambient air stability more than 160 days. Further the large area device (>1 cm²) device shows 13.04% PCE with Jsc = 21.47 mAcm^?2, V_OC = 0.996 V and FF = 0.61. We have also demonstrated >13% efficiency for large area device (>1.1 cm²), demonstrating that the developed method is simple, cost effective and promising towards large area device fabrication. The developed methodology based on low cost carbon hole extraction layer will be helpful towards waterproof and air stable perovskite solar cells for large-area devices.     

Understanding Hydrogen Bonding Interactions in Crosslinked Methylammonium Lead Iodide Crystals: Towards Reducing Moisture and Light Degradation Pathways

Methylammonium lead halide perovskite‐based solar cells have demonstrated efficiencies as high as 24.2 %, highlighting their potential as inexpensive and solution‐processable alternatives to silicon solar cell technologies. Poor stability towards moisture, ultraviolet irradiation, heat, and a bias voltage of the perovskite layer and its various device interfaces limits the commercial feasibility of this material for outdoor applications. Herein, we investigate the role of hydrogen bonding interactions induced when metal halide perovskite crystals are crosslinked with alkyl or π‐conjugated boronic acid small molecules (‐B(OH)₂). The crosslinked perovskite crystals are investigated under continuous light irradiation and moisture exposure. These studies demonstrate that the origin of the interaction between the alkyl or π‐conjugated crosslinking molecules is due to hydrogen bonding between the ‐B(OH)₂ terminal group of the crosslinker and the I of the [PbI₆]^4? octahedra of the perovskite layer. Also, this interaction influences the stability of the perovskite layer towards moisture and ultraviolet light irradiation. Morphology and structural analyses, as well as IR studies as a function of aging under both dark and light conditions show that π‐conjugated boronic acid molecules are more effective crosslinkers of the perovskite crystals than their alkyl counterparts thus imparting better stability towards light and moisture degradation.     

Molecular Bridge on Buried Interface for Efficient and Stable Perovskite Solar Cells

The interface of perovskite solar cells (PSCs) is significantly important for charge transfer and device stability, while the buried interface with the impact on perovskite film growth has been paid less attention. Herein, we use a molecular modifier, glycocyamine (GDA) to build a molecular bridge on the buried interface of SnO₂/perovskite, resulting in superior interfacial contact. This is achieved through the strongly interaction between GDA and SnO₂, which also appreciably modulates the energy level. Moreover, GDA can regulate the perovskite crystal growth, yielding perovskite film with enlarged grain size and absence of pinholes, exhibiting substantially reduced defect density. Consequently, PSCs with GDA modification demonstrate significant improvement of open circuit voltage (close to 1.2 V) and fill factor, leading to an improved power conversion efficiency from 22.60 % to 24.70 %. Additionally, stabilities of GDA devices under maximum power point and 85 °C heat both perform better than the control devices.     

Stable and Low‐Cost Mesoscopic CH3NH3PbI2Br Perovskite Solar Cells by using a Thin Poly(3‐hexylthiophene) Layer as a Hole Transporter

Mesoscopic perovskite solar cells using stable CH₃NH₃PbI₂Br as a light absorber and low‐cost poly(3‐hexylthiophene) (P3HT) as hole‐transporting layer were fabricated, and a power conversion efficiency of 6.64 % was achieved. The partial substitution of iodine with bromine in the perovskite led to remarkably prolonged charge carrier lifetime. Meanwhile, the replacement of conventional thick spiro‐MeOTAD layer with a thin P3HT layer has significantly reduced the fabrication cost. The solar cells retained their photovoltaic performance well when they were exposed to air without any encapsulation, presenting a favorable stability. The combination of CH₃NH₃PbI₂Br and P3HT may render a practical and cost‐effective solid‐state photovoltaic system. The superior stability of CH₃NH₃PbI₂Br is also promising for other photoconversion applications.     

Dual-Interface Engineering in Perovskite Solar Cells with 2D Carbides

Passivating the interfaces between the perovskite and charge transport layers is crucial for enhancing the power conversion efficiency (PCE) and stability in perovskite solar cells (PSCs). Here we report a dual-interface engineering approach to improving the performance of FA_0.85MA_0.15Pb(I_0.95Br_0.05)₃-based PSCs by incorporating Ti₃C₂Cl_x Nano-MXene and o-TB-GDY nanographdiyne (NanoGDY) into the electron transport layer (ETL)/perovskite and perovskite/ hole transport layer (HTL) interfaces, respectively. The dual-interface passivation simultaneously suppresses non-radiative recombination and promotes carrier extraction by forming the Pb−Cl chemical bond and strong coordination of π-electron conjugation with undercoordinated Pb defects. The resulting perovskite film has an ultralong carrier lifetime exceeding 10 μs and an enlarged crystal size exceeding 2.5 μm. A maximum PCE of 24.86 % is realized, with an open-circuit voltage of 1.20 V. Unencapsulated cells retain 92 % of their initial efficiency after 1464 hours in ambient air and 80 % after 1002 hours of thermal stability test at 85 °C.     

Retardation of Trap-Assisted Recombination in Lead Halide Perovskite Solar Cells by a Dimethylbiguanide Anchor Layer

Reaching the full potential of solar cells based on photo-absorbers of organic-inorganic hybrid perovskites requires highly efficient charge extraction at the interface between perovskite and charge transporting layer. This demand is generally challenged by the presence of under-coordinated metal or halogen ions, causing surface charge trapping and resultant recombination losses. These problems can be tackled by introducing a small molecule interfacial anchor layer based on dimethylbiguanide (DMBG). Benefitting from interactions between the nitrogen-containing functional groups in DMBG and unsaturated ions in CH₃NH₃PbI₃ perovskites, the electron extraction of TiO₂ is dramatically improved in association with reduced Schottky–Read–Hall recombination, as revealed by photoluminescence spectroscopy. As a consequence, the power conversion efficiency of CH₃NH₃PbI₃ solar cells is boosted from 17.14 to 19.1 %, showing appreciably reduced hysteresis. The demonstrated molecular strategy based on DMBG enables one to achieve meliorations on key figures of merit in halide perovskite solar cells with improved stability.