3D Multilayered paper‐ and thread/paper‐based microfluidic devices for bioassays

In this paper we describe the fabrication of novel 3D microfluidic paper‐based analytical devices (3D‐μPADs) and a 3D microfluidic thread/paper‐based analytical device (3D‐μTPAD) to detect glucose and BSA through colorimetric assays. The 3D‐μPAD and 3D‐μTPAD consisted of three (wax, heat pressed wax‐printed paper, single‐sided tape) and four (hole‐punched single‐sided tape, blank chromatography circles, heat‐pressed wax‐printed paper, hole‐punched single‐sided tape containing trifurcated thread) layers, respectively. The saturation curves for each assay were generated for all platforms. For the glucose assay, a solution of glucose oxidase (GOx), horseradish peroxidase, and potassium iodide was flowed through each platform and, upon contact with glucose, generated a yellow‐brown color indicative of the oxidation of iodide to iodine. For the protein assay, BSA was flowed through each device and, upon contact with citrate buffer and tetrabromophenol blue, resulted in a color change from yellow to blue. The devices were dried, scanned, and analyzed yielding a correlation between either yellow intensity and glucose concentration or cyan intensity and BSA concentration. A similar glucose assay, using unknown concentrations of glucose in artificial urine, was conducted and, when compared to the saturation curve, showed good correlation between the theoretical and actual concentrations (percent differences <10%). The development of 3D‐μPADs and 3D‐μTPADs can further facilitate the use of these platforms for colorimetric bioassays.     

Thread/paper‐ and paper‐based microfluidic devices for glucose assays employing artificial neural networks

This paper describes the fabrication of and data collection from two microfluidic devices: a microfluidic thread/paper based analytical device (μTPAD) and 3D microfluidic paper‐based analytical device (μPAD). Flowing solutions of glucose oxidase (GOx), horseradish peroxidase (HRP), and potassium iodide (KI), through each device, on contact with glucose, generated a calibration curve for each platform. The resultant yellow‐brown color from the reaction indicates oxidation of iodide to iodine. The devices were dried, scanned, and analyzed yielding a correlation between yellow intensity and glucose concentration. A similar procedure, using an unknown concentration of glucose in artificial urine, is conducted and compared to the calibration curve to obtain the unknown value. Studies to quantify glucose in artificial urine showed good correlation between the theoretical and actual concentrations, as percent differences were ≤13.0%. An ANN was trained on the four‐channel CMYK color data from 54 μTPAD and 160 μPAD analysis sites and Pearson correlation coefficients of R = 0.96491 and 0.9739, respectively, were obtained. The ANN was able to correctly classify 94.4% (51 of 54 samples) and 91.2% (146 of 160 samples) of the μTPAD and μPAD analysis sites, respectively. The development of this technology combined with ANN should further facilitate the use of these platforms for colorimetric analysis of other analytes.     

Carrier ampholyte‐free isoelectric focusing on a paper‐based analytical device for the fractionation of proteins

Isoelectric focusing plays a critical role in the analysis of complex protein samples. Conventionally, isoelectric focusing is implemented with carrier ampholytes in capillary or immobilized pH gradient gel. In this study, we successfully exhibited a carrier ampholyte‐free isoelectric focusing on paper‐based analytical device. Proof of the concept was visually demonstrated with color model proteins. Experimental results showed that not only a pH gradient was well established along the open paper fluidic channel as confirmed by pH indicator strip, the pH gradient range could also be tuned by the catholyte or anolyte. Furthermore, the isoelectric focusing fractions from the paper channel can be directly cut and recovered into solutions for post analysis with sodium dodecyl sulfate‐polyacrylamide gel electrophoresis and matrix‐assisted laser desorption/ionization‐time‐of‐flight mass spectrometry. This paper‐based isoelectric focusing method is fast, cheap, simple and easy to operate, and could potentially be used as a cost‐effective protein sample clean‐up method for target protein analysis with mass spectrometry.     

Use of multiple colorimetric indicators for paper-based microfluidic devices

We report here the use of multiple indicators for a single analyte for paper-based microfluidic devices (μPAD) in an effort to improve the ability to visually discriminate between analyte concentrations. In existing μPADs, a single dye system is used for the measurement of a single analyte. In our approach, devices are designed to simultaneously quantify analytes using multiple indicators for each analyte improving the accuracy of the assay. The use of multiple indicators for a single analyte allows for different indicator colors to be generated at different analyte concentration ranges as well as increasing the ability to better visually discriminate colors. The principle of our devices is based on the oxidation of indicators by hydrogen peroxide produced by oxidase enzymes specific for each analyte. Each indicator reacts at different peroxide concentrations and therefore analyte concentrations, giving an extended range of operation. To demonstrate the utility of our approach, the mixture of 4-aminoantipyrine and 3,5-dichloro-2-hydroxy-benzenesulfonic acid, o-dianisidine dihydrochloride, potassium iodide, acid black, and acid yellow were chosen as the indicators for simultaneous semi-quantitative measurement of glucose, lactate, and uric acid on a μPAD. Our approach was successfully applied to quantify glucose (0.5-20 mM), lactate (1-25 mM), and uric acid (0.1-7 mM) in clinically relevant ranges. The determination of glucose, lactate, and uric acid in control serum and urine samples was also performed to demonstrate the applicability of this device for biological sample analysis. Finally results for the multi-indicator and single indicator system were compared using untrained readers to demonstrate the improvements in accuracy achieved with the new system.     

Portable paper‐based device for quantitative colorimetric assays relying on light reflectance principle

This paper presents a novel paper‐based analytical device based on the colorimetric paper assays through its light reflectance. The device is portable, low cost (<20 dollars), and lightweight (only 176 g) that is available to assess the cost‐effectiveness and appropriateness of the original health care or on‐site detection information. Based on the light reflectance principle, the signal can be obtained directly, stably and user‐friendly in our device. We demonstrated the utility and broad applicability of this technique with measurements of different biological and pollution target samples (BSA, glucose, Fe, and nitrite). Moreover, the real samples of Fe (II) and nitrite in the local tap water were successfully analyzed, and compared with the standard UV absorption method, the quantitative results showed good performance, reproducibility, and reliability. This device could provide quantitative information very conveniently and show great potential to broad fields of resource‐limited analysis, medical diagnostics, and on‐site environmental detection.     

A rapid,straightforward, and print house compatible mass fabrication method for integrating 3D paper‐based microfluidics

Three‐dimensional (3D) paper‐based microfluidics, which is featured with high performance and speedy determination, promise to carry out multistep sample pretreatment and orderly chemical reaction, which have been used for medical diagnosis, cell culture, environment determination, and so on with broad market prospect. However, there are some drawbacks in the existing fabrication methods for 3D paper‐based microfluidics, such as, cumbersome and time‐consuming device assembly; expensive and difficult process for manufacture; contamination caused by organic reagents from their fabrication process. Here, we present a simple printing–bookbinding method for mass fabricating 3D paper‐based microfluidics. This approach involves two main steps: (i) wax‐printing, (ii) bookbinding. We tested the delivery capability, diffusion rate, homogeneity and demonstrated the applicability of the device to chemical analysis by nitrite colorimetric assays. The described method is rapid (<30 s), cheap, easy to manipulate, and compatible with the flat stitching method that is common in a print house, making itself an ideal scheme for large‐scale production of 3D paper‐based microfluidics.     

Development of a microfluidic‐based assay on a novel nitrocellulose platform

A novel microfluidic paper‐based analytical device (μPAD) utilizing a nitrocellulose (NC) membrane to detect IgG antibodies through a colorimetric analysis is described. The μPAD was constructed using layered polyethylene terephthalate (PET) and pressure‐sensitive adhesives (PSA). The biotin labeled Goat Anti‐Mouse IgG antibody was spotted and dried on the NC channel prior to subjecting it to a series of wash solutions (Tris‐tween), increasing concentrations of alkaline phosphatase conjugated to streptavidin (Strep‐ALP), and para‐nitrophenyl phosphate (p‐NPP) realizing a vibrant yellow color. The reaction proceeds for 10 min before applying the p‐NPP stop solution. The device was then dried, scanned, and analyzed yielding a linear range of inverse yellow color intensities versus Strep‐ALP concentrations. The development of this simple μPAD should further facilitate the use of NC in colorimetric assays to detect and quantitate antibodies.     

Mixed thread/paper‐based microfluidic chips as a platform for glucose assays

A novel microfluidic thread/paper‐based analytical device (μTPAD) to detect glucose through a colorimetric assay is described. The μTPAD was fabricated from nylon thread trifurcated into three channels terminating at analysis sites comprised of circular zones of chromatography paper, which have previously been spotted with glucose of different concentrations. A solution of glucose oxidase (GOx), horseradish peroxidase (HRP), and potassium iodide (KI) is transported via capillary action to the analysis sites where a yellow‐brown color is observed indicating oxidation of iodide to iodine. The device was then dried, scanned, and analyzed yielding a correlation between yellow intensity and glucose concentrations. Both a flat platform constructed mainly of tape, and a cone platform constructed from tape and polyvinyl chloride, are described. Studies to quantitate glucose in artificial urine showed good correlation using the μTPAD.     

Fast and Effective Turn‐on Paper‐based Phosphorescence Biosensor for Detection of Glucose in Serum

In this study, a turn‐on paper‐based optical analytical system with a rapid, sensitive and quantitative response for glucose was developed. The luminescence sensing material, crystalline iridium(III)‐Zn(II) coordination polymers, or Ir‐Zn_e, was grown electrochemically on stainless steel mesh and then deposited on filter paper. This sensing substrate was subsequently built up under glucose oxidase encapsulated in hydrogel and then immobilized on egg membrane with the layer‐by‐layer method. Once the glucose solution was dropped onto the paper, the oxygen content was depleted simultaneously with a concomitant increase in the phosphorescence of Ir‐Zn_e. The detection limit for glucose was 0.05 mM. The linear dynamic range for the determination of glucose was 0.05–8.0 mM with a correlation coefficient (R²) of 0.9956 (y=68.11 [glucose]?14.72). The response time was about 0.12 s, and the sample volume was less than 5 μL. The effects of mesh size, buffer concentration, pH, enzyme concentration, temperature, and interference, and the stability of the biosensor, have also been studied in detail. Finally, the biosensor was successfully applied to the determination of glucose in human serum.     

Microfunnel‐filter‐based emulsification microextraction followed by gas chromatography for simple determination of organophosphorus pesticides in environmental water samples

A simple and fast method named microfunnel‐filter‐based emulsification microextraction is introduced for an efficient determination of some organophosphorus pesticides including diazinon, malathion, and chlorpyrifos in the environmental samples including the river, sea, and well water. This method is based upon the dispersion of a low‐toxicity organic solvent (dihexyl ether), as the extractant, in a high volume of an aqueous sample solution (45 mL). It is implemented without a centrifugation step, and using a syringe filter and a micro‐funnel, the phase separation and transfer of the enriched analytes to the gas chromatograph are simply achieved. By filtration of the extractant phase, a suitable sample clean‐up is obtained, and the total extraction time is just a few minutes. The factors influencing the extraction efficiency are optimized, and under the optimal conditions, the proposed method provides a good linearity (in the range of 15–1500 ng/mL (R² > 0.996). A high enrichment factor is obtained (in the range of 306–342), and the method provides low limits of detection and quantification (in the ranges of 4–8 and 15–25 ng/mL, respectively).     

Sensitive determination of chloroanilines in water samples by hollow fiber‐based liquid‐phase microextraction prior to capillary electrophoresis with amperometric detection

A hollow fiber‐based liquid‐phase microextraction method has been developed for enrichment of trace chloroanilines in water samples. Target analytes including aniline, three mono‐chlorinated aniline isomers (o‐chloroaniline, m‐chloroaniline, and p‐chloroaniline) and four mono‐chlorinated methylaniline isomers (2‐chloro‐4‐methylaniline, 3‐chloro‐4‐methylaniline, 4‐chloro‐2‐methylaniline, and 5‐chloro‐2‐methylaniline) were determined by CE with amperometric detection after microextraction. Several factors that affect separation, detection, and extraction efficiency were investigated. Under the optimum conditions, eight aniline compounds could be well separated from other components coexisting in water samples within 25 min, exhibiting a linear calibration over three orders of magnitude (r > 0.998); the obtained enrichment factors were between 51 and 239, and the LODs were in the range of 0.01–0.1 ng/mL. The proposed method has been applied for the analyses of real environmental water and sewage samples with relative recoveries in the range of 83–108%.     

Miniaturized capillary ion chromatograph with UV light‐emitting diode based indirect absorbance detection for anion analysis in potable and environmental waters

A miniaturized, flexible, and low‐cost capillary ion chromatography system has been developed for anion analysis in water. The ion chromatography has an open platform, modular design, and allows for ease of modification. The assembled platform weighs ca. 0.6 kg and is 25 × 25 cm in size. Isocratic separation of common anions (F^–, Cl^–, NO₂^–, Br^–, and NO₃^–) could be achieved in under 15 min using sodium benzoate eluent at a flow rate of 3 μL/min, a packed capillary column (0.150 × 150 mm) containing Waters IC‐Pak 10 μm anion exchange resin, and light‐emitting diode based indirect UV detection. Several low UV light‐emitting diodes were assessed in terms of sensitivity, including a new 235 nm light‐emitting diode, however, the highest sensitivity was demonstrated using a 255 nm light‐emitting diode. Linear calibration ranges applicable to typical natural water analysis were obtained. For retention time and peak area repeatability, relative standard deviation values ranged from 0.60–0.95 and 1.95–3.53%, respectively. Several water samples were analysed and accuracy (recovery) was demonstrated through analysis of a prepared mixed anion standard. Relative errors of –0.36, –1.25, –0.80, and –0.76% were obtained for fluoride, chloride, nitrite, and nitrate, respectively.     

Development of Electrochemical Paper‐based Glucose Sensor Using Cellulose‐4‐aminophenylboronic Acid‐modified Screen‐printed Carbon Electrode

The present work describes the fabrication of paper‐based analytical devices (μPADs) by immobilization of glucose oxidase onto the screen printed carbon electrodes (SPCEs) for the electrochemical glucose detection. The sensitivity towards glucose was improved by using a SPCE prepared from homemade carbon ink mixed with cellulose acetate. In addition, 4‐aminophenylboronic acid (4‐APBA) was used as a redox mediator giving a lower detection potential for improvement selectivity. Under optimized condition, the detection limit was 0.86 mM. The proposed device was applied in real samples. This μPAD has many advantages including low sample consumption, rapid analysis method, and low device cost.     

Single‐run capillary electrophoresis method for the fast simultaneous determination of amoxicillin,clavulanate, and potassium

We report a new fast method for the simultaneous determination of amoxicillin, clavulanate, and potassium by capillary electrophoresis with capacitively coupled contactless conductivity detection. Samples containing potassium as the cation, and both amoxicillin and clavulanate as anions were determined simultaneously in a single run (in less than 45 s) using 10 mmol/L of both 2‐amino‐2‐hydroxymethyl‐propane‐1,3‐diol and 3‐{[2‐hydroxy‐1,1‐bis(hydroxymethyl)ethyl]amino}‐1‐propanesulfonic acid (pH 8.4) as the background electrolyte. Limits of detection were 25.0, 5.0, and 4.0 μmol/L for amoxicillin, clavulanate, and potassium, respectively. The proposed method is inexpensive, simple, fast (75 injections h⁻¹), environment friendly (minimal waste generation), and accurate (recovery values between 98 and 103%). The results obtained with the proposed method were statistically similar (95% confidence level) to those obtained by using high‐performance liquid chromatography (amoxicillin and clavulanate) and flame photometry (potassium).     

Immunobinding‐induced alteration in the electrophoretic mobility of proteins: An approach to studying the preconcentration of an acidic protein under cationic isotachophoresis

The objective of this study is to explore an approach for analyzing negatively charged proteins using paper‐based cationic ITP. The rationale of electrophoretic focusing the target protein with negative charges under unfavorable cationic ITP condition is to modify the electrophoretic mobility of the target protein through antigen‐antibody immunobinding. Cationic ITP was performed on a paper‐based analytical device that was fabricated using fiberglass paper. The paper matrix was modified with (3‐aminopropyl)trimethoxysilane to minimize sample attraction to the surface for cationic ITP. Negatively charged BSA was used as the model target protein for the cationic ITP experiments. No electrophoretic mobility was observed for BSA‐only samples during cationic ITP experimental condition. However, the presence of a primary antibody to BSA significantly improved the electrokinetic behavior of the target protein. Adding a secondary antibody conjugated with amine‐rich quantum dots to the sample further facilitated the concentrating effect of ITP, reduced experiment time, and elevated the stacking ratio. Under our optimized experimental conditions, the cationic ITP‐based paper device electrophoretically stacked 94% of loaded BSA in less than 7 min. Our results demonstrate that the technique has a broad potential for rapid and cost‐effective isotachphoretic analysis of multiplex protein biomarkers in serum samples at the point of care.     

Method for routine screening of pesticides and metabolites in meat based baby‐food using extraction and gas chromatography‐mass spectrometry

A simple and complete multiresidue method has been developed for the routine determination of 236 pesticides and degradation products, in meat based baby‐food. This original approach combines a modified Quick Easy Cheap Effective Rugged and Safe (QuEChERS) sample preparation method using a triple partitioning extraction step with water/ACN/hexane and a system composed of GC with programmable temperature vaporization injector hyphenated to an IT‐MS. Detection was performed in full scan mode, with one quantification ion and one identification ion. We firstly report here the hexane addition in the extraction step to eliminate a major part of lipophile co‐extracts. Direct consequences were the increasing of method sensitivity and the diminishment of the frequency of maintenance of the analytical instrument. The recovery data were obtained by spiking blank samples at three concentration levels (10, 50 and 200 μg/kg) over five replicates, yielding average recoveries in the range 70–121% with a RSD evaluated between 2–15%. Linearity was fixed in the range of 10–300 μg/kg with determination coefficients (R²) superior or equal to 0.9814 for all target analytes. Best LODs and LOQs were established as 0.03 and 0.1 μg/kg, respectively. Total instrumental analysis of all molecules was carried out in less than 1 h.     

Rapid determination of nitrite in foods in acidic conditions by high‐performance liquid chromatography with fluorescence detection

In this study, a simple, rapid, and sensitive method for the determination of nitrite (NO₂^?) in food samples by high‐performance liquid chromatography with fluorescence detection in acidic conditions had been developed. The derivatization of the nitrite with 2,3‐diaminonaphthalene was performed in acidic conditions to yield the highly fluorescent 2,3‐naphthotriazole, which was directly analyzed by high‐performance liquid chromatography with fluorescence detection without adjusting the solution to alkaline. The analysis column was reversed‐phase C₈ column. A constant flow rate of 1.0 mL/min was employed using water/acetonitrile as the mobile phase in isocratic mode (70:30, v/v). Fluorescence was monitored with excitation at 375 nm and emission at 415 nm. The standard calibration curves were linear for nitrite in different matrixes in the concentration range of 0–100 μg/L, and the correlation coefficients ranged from 0.9978 to 0.9998. The limits of detection and quantification were in the ranges of 0.012–0.060 and 0.040–0.20 mg/kg, respectively. The recoveries of nitrite from samples spiked at three different concentrations were 74.0–113.2%, and the relative standard deviations of the recovery results (n = 6) were 1.67–10.8%. The proposed method has good repeatability and is very sensitive and simple. It has been successfully used to determine nitrite in foods.     

Simple field‐based automated dispersive liquid–liquid microextraction of trace level phthalate esters in natural waters with gas chromatography and mass spectrometric analysis

A small, simple, and field‐based automated dispersive liquid–liquid microextraction method followed by gas chromatography mass spectrometric analysis was developed for trace level phthalate esters analysis in natural waters. With a single syringe pump that is coupled with a multiposition valve, the whole extraction procedure including cleaning, sampling, mixing of extractant and disperser solvents, extraction, phase separation, and analytes collection was carried out in a totally automated way with a sample throughput of 21 h^?1. Key factors, such as type and ratio of the extractant and disperser solvent, aspiration flow rate, extraction time, and matrix effect, were thoroughly investigated. Under the optimum conditions, linearity was found in the range from 0.03 to 60 μg/L. Limits of detection ranged from 0.0015 to 0.003 μg/L. Enrichment factors were in a range of 106–141. Reproducibility and recoveries were assessed by testing a series of three natural water samples that were spiked with different concentration levels. Finally, the proposed method was successfully applied in analysis of real surface waters. The developed system is inexpensive, light (2.6 kg), simple to use, applicable in the field, with high sample throughput, and sensitive enough for trace level phthalate esters analysis in natural waters.     

A fast and green reversed‐phase HPLC method with fluorescence detection for simultaneous determination of amlodipine and celecoxib in their newly approved fixed‐dose combination tablets

A fast, green, sensitive, and accurate analytical method using high‐performance liquid chromatography couple with fluorescence detection was established and validated for the simultaneous determination of amlodipine besylate and celecoxib in their recently approved fixed‐dose combination tablets (1:20). Separation of the two drugs was achieved on C₁₈ reversed‐phase column (Thermo ODS Hypersil, 4.6 × 250 mm, particle size 5 µm) using acetonitrile:potassium phosphate buffer (50 mM; pH 5.5, 60:40 v/v) as a mobile phase at 40°C, which eluted at a rate of 1 mL/min. Detection was carried out with excitation and emission wavelengths of 360 and 446 nm for amlodipine and 265 and 359 nm for celecoxib, respectively. The method was linear over a concentration range of 0.05‐2 and 0.05‐10 µg/mL and limit of detection reached to 0.017 and 0.0167 µg/mL for amlodipine and celecoxib, respectively. The developed method was successfully applied to assess the cited drugs in their newly FDA approved fixed‐dose combination tablet dosage form. Furthermore, the method was found to be sensitive and eco‐friendly green alternative to the reported methods as it was evaluated according to the green analytical procedure index tool guidelines and analytical Eco‐Scale.     

A colorimetric squaraine-based probe and test paper for rapid naked eyes detection of copper ion (II)

A colorimetric probe N,N’-bis(2-methoxy-ethyl)-2,3,3-trimethyl-3H-squaraine (MOESQ) with H₂O solubility was synthesized to detect Cu²⁺. MOESQ exhibits good selectivity, high sensitivity and fast UV-Vis response toward Cu²⁺ over other competing ions in CH₃CN. The detection limit of MOESQ for Cu²⁺ in CH₃CN can reach 1.88?×?10^?7?molL^?1. By adsorbing MOESQ on the chromatography paper, a colorimetric test paper for Cu²⁺ was prepared, which could detect Cu²⁺ with the color change from blue to faint yellow even in the limit of detection concentration of 10^?6?molL^?1.