A Sensitive Sensor Based on CuTSPc and Reduced Graphene Oxide for Simultaneous Determination of the BHA and TBHQ Antioxidants in Biodiesel Samples

A novel and sensitive electrochemical sensor was developed for the simultaneous determination of the butylated hydroxyanisole (BHA) and tert‐butylhydroquinone (TBHQ) antioxidants in biodiesel samples employing the differential pulse voltammetry (DPV). In this sense, a glassy carbon electrode (GCE) modified with copper (II) tetrasulfonated phthatocyanine immobilized on reduced graphene oxide (CuTSPc/rGO) allowed the detection of BHA and TBHQ at potentials lower than those observed at unmodified electrodes. The sensor was characterized by cyclic voltammetry (CV) and linear scan voltammetry (LSV). After optimization of the experimental parameters, the analytical curves for simultaneous determination of BHA and TBHQ by DPV technique demonstrated an excellent linear response from 0.1 to 500 µmol L^?1 with detection limit of 0.045 µmol L^?1 for TBHQ and 0.036 µmol L^?1 for BHA. Finally, the proposed method was successfully applied in the simultaneous determination of BHA and TBHQ in six biodiesel samples, and the results obtained were found to be similar to those obtained using the HPLC method with agreement at 95 % confidence level.     

Effect of Different Carbon Blacks on the Simultaneous Electroanalysis of Drugs as Water Contaminants Based on Screen‐printed Sensors

For the construction of the sensor, three different carbon black (CB) materials (VULCAN XC72R, BLACK PEARLS 4750 and CB N220) were explored as modifying nanomaterial. Firstly, the electrochemical activity of the each SPE modified was compared by cyclic voltammetry and electrochemical impedance spectroscopy technique, using [Fe(CN)₆]^3?/4? as redox couple. After demonstrating that electrodes modified with different types of CB were characterized by improved electrochemical performances when compared with bare electrodes, and among them, electrodes modified with CB BP4750 is characterised by slightly better electrochemical properties, this type of electrode was used for the development of the analytical method. By applying SWV technique in 0.2 mol L^?1 phosphate buffer (pH 3.0), the obtained analytical curves for ACP and LVF were found linearly from 4.0 to 80.0 μmol L^?1 and from 0.90 to 70.0 μmol L^?1 with limit of detection of 2.6 μmol L^?1 and 0.42 μmol L^?1 for ACP and LVF, respectively. Finally, the quantification of these drugs in river water was evaluated using the new here‐proposed sensor by recovery method in spiked samples, obtaining satisfactory recovery values. The results achieved demonstrated that the developed analytical tool is of great analytical interest being easy to use, cost‐effective, miniaturized, and thus suitable for low cost on site analysis.     

A Novel Strategy for Quantifying Clopidogrel Using Square‐wave Voltammetry and a Boron‐doped Diamond Film

The voltammetric behavior of clopidogrel bisulfate (CLO), an antiplatelet agent, was investigated for the first time in the literature on a cathodically pretreated boron‐doped diamond electrode (CP‐BDDE) using cyclic (CV) and square‐wave voltammetry (SWV). It was observed an anodic peak for CLO, suitable for analytical purposes, at about 1.15 V (vs. Ag/AgCl (3.0 mol L^?1 KCl)) by CV in Britton‐Robinson buffer solution (pH 5.0). On the physical‐chemical characterization of the interface phenomena, it was proved that electrode reaction of the analyte was controlled by a diffusion process. At optimized square‐wave parameters (pulse amplitude of 60 mV, frequency of 30 Hz and scan increment of 3 mV), the obtained analytical curve was linear for the CLO concentration range from 0.60 to 60.0 μmol L^?1, with a detection limit of 0.60 μmol L^?1. The simple, rapid and greener analytical method, based on CP‐BDDE electrochemical sensor, was successfully applied in real samples (pharmaceuticals and urine).     

Sensitive Voltammetric Determination of Bisphenol A Based on a Glassy Carbon Electrode Modified with Copper Oxide‐Zinc Oxide Decorated on Graphene Oxide

A highly sensitive and selective chemical sensor was prepared based on metallic copper‐copper oxides and zinc oxide decorated graphene oxide modified glassy carbon electrode (Cu?Zn/GO/GCE) through an easily electrochemical method for the quantification of bisphenol A (BPA). The composite electrode was characterized via scanning electron microscopy (SEM), X‐Ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS). The electrochemical behavior of BPA in Britton‐Robinson (BR) buffer solution (pH 7.1) was examined using cyclic voltammetry (CV). Under optimized conditions, the square wave voltammetry (SWV) response of Cu?Zn/GO/GCE towards BPA indicates two linear relationships within concentrations (3.0 nmol L^?1?0.1 μmol L^?1 and 0.35 μmol L^?1?20.0 μmol L^?) and has a low detection limit (0.88 nmol L^?1). The proposed electrochemical sensor based on Cu?Zn/GO/GCE is both time and cost effective, has good reproducibility, high selectivity as well as stability for BPA determination. The developed composite electrode was used to detect BPA in various samples including baby feeding bottle, pacifier, water bottle and food storage container and satisfactory results were obtained with high recoveries.     

Square‐Wave Voltammetry Applied to the Analysis of the Dye Marker,Solvent Blue 14, in Kerosene and Fuel Alcohol

The purpose of this paper is to develop an electroanalytical method based on square‐wave voltammetry (SWV) for the determination of the solvent blue 14 (SB‐14) in fuel samples. The electrochemical reduction of SB‐14 at glassy carbon electrode in a mixture of Britton‐Robinson buffer with N,N‐dimethylformamide (1 : 1, v/v) presented a well‐defined peak at?0.40 V vs. Ag/AgCl. All parameters of the SWV technique were optimized and the electroanalytical method presented a linear response from 1.0×10^?6 to 6.0×10^?6 mol L^?1 (r=0.998) with a detection limit of 2.90×10^?7 mol L^?1. The developed method was successfully utilized in the quantification of the dye SB‐14 in kerosene and alcohol samples with average recovery from 93.00 to 98.10%.     

A Simple Approach to Simultaneous Electroanalytical Quantification of Acetaminophen and Tramadol Using a Boron‐doped Diamond Electrode in the Existence of Sodium Dodecyl Sulfate

The present work describes the individual, selective and simultaneous quantification of acetaminophen (ACP) and tramadol hydrochloride (TRA) using a modification‐free boron‐doped diamond (BDD) electrode. Cyclic voltammetric measurements revealed that the profile of the binary mixtures of ACP and TRA were manifested by two irreversible oxidation peaks at about +1.04 V (for ACP) and +1.61 V (for TRA) in Britton‐Robinson (BR) buffer pH 3.0. TRA oxidation peak was significantly improved in the presence of anionic surfactant, sodium dodecyl sulfate (SDS), while ACP signal did not change. By employing square‐wave stripping mode in BR buffer pH 3.0 containing 8×10^?4 mol L^?1 SDS after 30 s accumulation under open‐circuit voltage, the BDD electrode could be used for quantification of ACP and TRA simultaneously in the ranges 1.0–70 μg mL^?1 (6.6×10^?6–4.6×10^?4 mol L^?1) and 1.0–70 μg mL^?1 (3.3×10^?6–2.3×10^?4 mol L^?1), with detection limits of 0.11 μg mL^?1 (7.3×10^?7 mol L^?1) and 0.13 μg mL^?1 (4.3×10^?7 mol L^?1), respectively. The practical applicability of the proposed approach was tested for the individual and simultaneous quantification of ACP and/or TRA in the pharmaceutical dosage forms.     

Resolution of a Mononitrophenol Isomers Mixture by Differential Alternative Pulses Voltammetry

The high resolution second order voltammetric technique, Differential Alternative Pulse Voltammetry (DAPV), was applied for the simultaneous quantification of the mononitrophenol (NP) isomers. Complete resolution of the three isomers was achieved at concentration ratios as high as 1 : 5, employing the corresponding anodic and cathodic peaks appeared on the DAPV curve. The working glassy carbon electrode was modified by a nanocomposite of graphite nanopowder and Au nanoparticles to increase the sensitivity. The linear concentration range was found to be extended up to 125 μmol L^?1 for both the m‐NP and p‐NP isomers, while the o‐NP isomer presented calibration plot of two linear sections: up to 100 μmol L^?1 and up to 225 μmol L^?1. The LOD was found to be as low as 1.5 μmol L^?1, 2.5 μmol L^?1, and 0.5 μmol L^?1 for o‐NP, m‐NP, and p‐NP, respectively. The accuracy of the proposed method was evaluated by quantification of spiked tap waters samples. No interference was observed from a range of phenolic compounds such as phenol, 4‐aminophenol, 4‐chlorophenol, 2,4‐dinitrophenol, and resorcinol.     

Determination of Blasticidin S in Spiked Rice Using SW Voltammetry with a Renewable Silver Amalgam Film Electrode

Blasticidin S (BS) was determined in spiked rice samples by square wave voltammetry (SWV) and square wave stripping voltammetry (SWSV) using a cyclic renewable silver amalgam film electrode (Hg(Ag)FE). It was found that the compound can act as an electrocatalyst. In Britton? Robinson buffer at pH 7.0 a signal connected with the hydrogen evolution reaction was detected at ?1.2 V versus Ag/AgCl. Validation of the method was carried out. The detection and quantification limits were found to be 2.13×10^?8 mol L^?1; 7.10×10^?8 mol L^?1 for SWV and 2.65×10^?9 mol L^?1; 8.85×10^?9 mol L^?1 for SWSV, respectively.     

Sensitive and Profitable Electrochemical Detection of Uric Acid in the Presence of Dopamine with a Novel Carbon Paste Electrode Decorated with a Copper(II) Complex

A new microcomposite with copper(II) complex and carbon paste (Cu_C/CPE) was developed to determine the uric acid (UA) content in the presence of dopamine (DP) and was characterized via cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and energy dispersive spectroscopy (EDS). The results showed high selectivity for UA compared with DP because the anodic peak currents for DP were near those of a CPE without Cu_c and were considerably increased for UA. The UA and DP increases were 86.9 % and 14.3 %, respectively, according to CV and 96.6 % and 25.5 %, respectively, according to square wave voltammetry (SWV) with the Cu_C/CPE. Moreover, the anodic peak separation for UA and DP was 0.17 V. With optimal parameters (pH, 3.3; adsorption time(t_ADS), 30 s;adsorption potential (E_ADS)_, 0.10 V), the anodic peak currents for UA were proportional to concentrations between 1.6 and 14.4 μmol L^?1 using standard solutions with UA concentrations ranging from 8.0–40.5 μmol L^?1 and real samples. The UA detection limit was 0.13 μmol L^?1. The new sensor was used to determine the UA contentin human urine samples, and the method was checked with a urine chemistry control from Bio‐Rad based on human urine spiked with quantities of UA and showed a recovery between 84 % and 106 % at concentrations below 10.0 μmol L^?1.     

Determination of three Tumor Biomarkers (Homovanillic Acid,Vanillylmandelic Acid,and 5‐Hydroxyindole‐3‐Acetic Acid) Using Flow Injection Analysis with Amperometric Detection

Flow injection analysis with amperometric detection (FIA‐AD) at screen‐printed carbon electrodes (SPCEs) in optimum medium of Britton‐Robinson buffer (0.04 mol ? L^?1, pH 2.0) was used for the determination of three tumor biomarkers (homovanillic acid (HVA), vanillylmandelic acid (VMA), and 5‐hydroxyindole‐3‐acetic acid (5‐HIAA)). Dependences of the peak current on the concentration of biomarkers were linear in the whole tested concentration range from 0.05 to 100 μmol ? L^?1, with limits of detection (LODs) of 0.065 μmol ? L^?1 for HVA, 0.053 μmol ? L^?1 for VMA, and 0.033 μmol ? L^?1 for 5‐HIAA (calculated from peak heights), and 0.024 μmol ? L^?1 for HVA, 0.020 μmol ? L^?1 for VMA, and 0.012 μmol ? L^?1 for 5‐HIAA (calculated from peak areas), respectively.     

Electroanalytical Method for Determining Pyrogallol in Biodiesel in the Presence of a Surfactant

A sensitive, straightforward electroanalytical method for determining pyrogallol (PY) in biodiesel in the presence of a surfactant was developed using a voltammetric technique and screen‐printed electrodes. The influence of surfactant addition (sodium dodecyl sulfate (SDS), Triton X‐100 (TX‐100), cetyltrimethylammonium bromide (CTAB), tetrabutylammonium iodide (TBAI), tetrabutylammonium bromide (TBAB), or tetraethylammonium bromide (TEAB)) on the supporting electrolyte (0.04 mol L^?1 Britton? Robinson buffer) was evaluated. Only CTAB significantly increased the oxidation peak current. Under optimal conditions, the method demonstrated linearity over the concentration range of 0.8–9.0×10^?6 mol L^?1, with limits of detection and quantification of 4.9×10^?7 and 1.5×10^?6 mol L^?1, respectively. The results were satisfactory, relative to those obtained using high‐performance liquid chromatography (HPLC).     

Simultaneous Electrochemical Determination of Hydroquinone and Bisphenol A using a Carbon Paste Electrode Modified with Silver Nanoparticles

In this paper, a rapid and sensitive modified electrode for the simultaneous determination of hydroquinone (HQ) and bisphenol A (BPA) is proposed. The simultaneous determination of these two compounds is extremely important since they can coexist in the same sample and are very harmful to plants, animals and the environment in general. A carbon paste electrode (CPE) was modified with silver nanoparticles (nAg) and polyvinylpyrrolidone (PVP). The PVP was used as a reducing and stabilizing agent of nAg from silver nitrate in aqueous media. The nAg‐PVP composite obtained was characterized by transmission electron microscopy and UV‐vis spectroscopy. The electrochemical behavior of HQ and BPA at the nAg‐PVP/CPE was investigated in 0.1 mol L⁻¹ B−R buffer (pH 6.0) using cyclic voltammetry (CV) and square wave voltammetry (SWV). The results indicate that the electrochemical responses are improved significantly with the use of the modified electrode. The calibration curves obtained by SWV, under the optimized conditions, showed linear ranges of 0.09–2.00 μmol L⁻¹ for HQ (limit of detection 0.088 μmol L⁻¹) and 0.04–1.00 μmol L⁻¹ for BPA (limit of detection 0.025 μmol L⁻¹). The modified electrode was successfully applied in the analysis of water samples and the results were comparable to those obtained using UV‐vis spectroscopy.     

Electroanalysis of the Anthelmintic Drug Bithionol at Edge Plane Pyrolytic Graphite Electrode

An electrochemical study of the anthelmintic drug bithionol using edge plane pyrolytic graphite electrode (EPPGE) is presented for the first time by applying different electrochemical techniques, such as cyclic voltammetry (CV), square‐wave voltammetry (SWV), square‐wave adsorptive stripping voltammetry (SWAdSV), and alternating current (AC) impedance spectroscopy. Mechanistic aspects of the electrode reaction were studied implying a quasireversible electrode reaction from an adsorbed state of the reactant, coupled with a follow‐up chemical reaction to a final electroinactive product. The overall mechanism appears totally irreversible under conditions of CV at moderate scan rate, while being quasireversible under conditions of the fast SWV. Furthermore, an optimisation of the analytical procedure for quantitative determination of bithionol was conducted by applying SWV in an adsorptive stripping mode. The calibration curve was constructed in the concentration range of 0.1–1.0 μmol L^?1 (R²=0.9984) with a sensitivity of 3.6 μA L μmol^?1 and LOD of 26.7 nmol L^?1. The simple and sensitive SWAdSV procedure was proved to be suitable for the analysis of spiked urine samples.     

Simultaneous Voltammetric Detection of Salsolinol and Uric Acid in the Presence of High Concentration of Ascorbic Acid with Gold Nanoparticles/Functionalized Multiwalled Carbon Nanotubes Composite Film Modified Electrode

This work demonstrates gold nanoparticles (AuNPs)/functionalized multiwalled carbon nanotubes (f‐MWCNT) composite film modified gold electrode via covalent‐bonding interaction self‐assembly technique for simultaneous determination of salsolinol (Sal) and uric Acid (UA) in the presence of high concentration of ascorbic acid (AA). In pH 7.0 PBS, the composite film modified electrode exhibits excellent voltammetric response for Sal and UA, while AA shows no voltammetric response. The oxidation peak current is linearly increased with concentrations of Sal from 0.24–11.76 μmol L^?1 and of UA from 3.36–96.36 μmol L^?1, respectively. The detection limits of Sal and UA is 3.2×10^?8 mol L^?1 and 1.7×10^?7 mol L^?1 , respectively.     

Development of an Amperometric Biosensor for β‐N‐Oxalyl‐L‐α,β‐Diaminopropionic Acid (β‐ODAP)

An amperometric method for the determination of the neurotoxic amino acid β‐N‐oxalyl‐L ‐α,β‐diaminopropionic acid (β‐ODAP) using a screen printed carbon electrode (SPCE) is reported. The electrode material was bulk‐modified with manganese dioxide and used as a detector in flow injection analysis (FIA). The enzyme glutamate oxidase (GlOx) was immobilized in a Nafion‐film on the electrode surface. The performance of the biosensor was optimized using glutamate as an analyte. Optimum parameters were found as: operational potential 440 mV (vs. Ag/AgCl), flow rate 0.2 mL min^?1, and carrier composition 0.1 mol L^?1 phosphate buffer (pH 7.75). The same conditions were used for the determination of β‐ODAP. The signal was linear within the concentration range 53–855 μmol L^?1 glutamate and 195–1950 μmol L^?1 β‐ODAP. Detection limits (as 3σ value) for both analytes were 9.12 and 111.0 μmol L^?1, respectively, with corresponding relative standard deviations of 3.3 and 4.5%. The biosensor retained more than 73% of its activity after 40 days of on‐line use.     

Simultaneous Determination of Phenolic Additives in Cosmetics by Micellar Electrokinetic Capillary Chromatography with Electrochemical Detection

A micellar electrokinetic capillary chromatography method with electrochemical detection (MECC‐ED) has been developed for the simultaneous determination of eight phenolic additives, including propyl gallate (PG), tert‐butylhydroquinone (TBHQ), butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT), methylparaben (MP), ethylparaben (EP), propylparaben (PP) and butylparaben (BP) in cosmetic products. Method development involved optimization of the working electrode, the pH value of running buffer, the concentration of sodium dodecyl sulfate (SDS), the separation voltage, and the sample injection time. Under the optimum conditions, all analytes can be well separated within 26 min at the separation voltage of 18 kV in a 9 mmol·L^?1 sodium dodecyl sulfate (SDS) ?60 mmol·L^?1 borate running buffer (pH 8.0). A 300 μm diameter carbon disk electrode generated good response at +0.90 V (vs. SCE) for all analytes. Linearity of the present method was over three orders of magnitude of analyte concentration with detection limits (S/N=3) ranging from 1.1×10^?7 to 1.2×10^?6 g·mL^?1 for all analytes. This proposed method has been successfully applied to the simultaneous determination of the above additives in commercial cosmetics, and the assay results were satisfactory.     

Response surface methodology for optimisation of 4,6-Dinitro-o-cresol quantification using hanging mercury drop electrode

A method for the pesticide DNOC (4,6-Dinitro-o-cresol) quantification using hanging mercury drop electrode (HMDE) and stripping square wave voltammetry (SSWV) optimisation is proposed. As a continuous cathodic current decrease was observed during the experiments, a waiting time, together with solution pH and SWV instrumental variables were optimised by factorial designs. From the two reduction current peaks values, only one was considered as dependent variable in the optimisation process. While the cathodic current peak and standard deviation were used in the waiting time and solution pH optimisation process, the instrumental parameters for SWV were optimised by using only current peak values. With the optimal parameters, a calibration curve from (0.01–0.55) × 10^?6 mol L^?1 with LOD of 2 × 10^?8 mol L^?1 was obtained. The proposed method was checked for DNOC quantification in different water samples obtained from Cordoba area and very good results, with recovery values around 102% were observed.     

Differential Pulse Voltammetric Determination of 2‐Methyl‐4,6‐Dinitrophenol using Bismuth Bulk Electrode

This work reports the application of bismuth bulk electrode (BiBE) for the determination of 2‐methyl‐4,6‐dinitrophenol (MDNP) by differential pulse voltammetry (DPV) in Britton‐Robinson buffer of pH 12.0 as an optimal medium. BiBE was prepared by transferring molten bismuth into a glass tube under constant stream of nitrogen. The linear concentration dependences were measured from 1 to 10 μmol ? L^?1 and from 10 to 100 μmol ? L^?1 by using optimum accumulation potential of ?0.7 V and optimum accumulation time 30 s. Under these conditions limit of determination and limit of quantification was 0.45 and 1.5 μmol ? L^?1, respectively. The developed method was successfully applied for the analysis of tap water as a model sample.     

Surfactant‐assisted dispersive liquid–liquid microextraction of nitrazepam and lorazepam from plasma and urine samples followed by high‐performance liquid chromatography with UV analysis

Surfactant‐assisted liquid–liquid microextraction followed by high‐performance liquid chromatography with UV detection has been developed for the simultaneous preconcentration and determination of lorazepam and nitrazepam in biological fluids. In this study, an ionic surfactant (cetyltrimethyl ammonium bromide) was used as an emulsifier. The predominant parameters affecting extraction efficiency such as the type and volume of extraction solvent, the type and concentration of surfactant, sample pH, and the concentration of salt added to the sample were investigated and opted. Under the optimum conditions (extraction solvent and its volume, 1‐octanol, 70 μL; surfactant and its concentration, 1 mL of ultra‐pure water containing 2 mmol L^?1 cetyltrimethyl ammonium bromide; sample pH = 9 and salt content of 10% NaCl w/v), the preconcentration factors were obtained in the range of 202–241 and 246–265 for nitrazepam and lorazepam, respectively. The limits of quantification for both drugs were 5 μg L^?1 in water sample and 10 μg L^?1 in biological fluids with R² values higher than 0.993. The suitability of the proposed method was successfully confirmed by the extraction and determination of the target drugs in human urine and plasma samples in the range of microgram per liter.     

A Sensitive Sensor Based on Single‐walled Carbon Nanotubes: Its Preparation,Characterization and Application in the Electrochemical Determination of Drug Clorsulon in Milk Samples

Within this paper, a glassy carbon electrode modified with single‐walled carbon nanotubes (SWCNTs?GCE) was prepared, and employed for the determination of clorsulon (Clo), which is a frequently used veterinary drug against common liver fluke. The comprehensive topographical and electrochemical characterizations of bare GCE and SWCNTs?GCE were performed by atomic force microscopy, electrochemical impedance spectroscopy, and cyclic voltammetry. Significantly enhanced electrochemical characteristics of SWCNTs?GCE toward a ferrocyanide/ferricyanide redox couple was observed when compared to bare GCE. Further, the prepared sensor was applied for the voltammetric determination of Clo, which was electrochemically investigated for the first time in this work. Voltammetric experiments were performed using square‐wave voltammetry with optimized parameters in phosphate buffer solution, pH 6.8, which was selected as the most suitable medium for the determination of Clo. The corresponding current at approx. +1.1 V increased linearly with Clo concentration within two linear dynamic ranges of 0.75–4.00 μmol L^?1 (R²=0.9934) and 4.00–15.00 μmol L^?1 (R²=0.9942) with a sensitivity for the first calibration range of 0.76 μA L μmol^?1, a limit of detection of 0.19 μmol L^?1, and a limit of quantification of 0.64 μmol L^?1. The developed method was subsequently applied for quantitative analysis of Clo in milk samples with results proving high repeatability and recovery.