Analysis of nitrogenous organic compounds from mainstream cigarette smoke using low‐temperature solvent extraction followed by comprehensive two‐dimensional gas chromatography with high‐resolution time‐of‐flight mass spectrometry

A method involving comprehensive two‐dimensional gas chromatography coupled to high‐resolution time‐of‐flight mass spectrometry was developed and applied to the analysis of nitrogenous organic compounds present in mainstream cigarette smoke trapped on self‐designed equipment. The samples were prepared using low‐temperature solvent extraction under liquid nitrogen and analyzed by comprehensive two‐dimensional gas chromatography with high‐resolution time‐of‐flight mass spectrometry. Important experimental parameters, such as the type and volume of the extraction solvent and flow rate of smoking, were optimized to improve the analysis parameter. The results indicated that 180 mL of diethyl ether in the low‐temperature solvent extraction apparatus system with a 4 mL/min smoke flow rate were the optimal conditions. Then, 85 nitrogenous organic compounds were identified and quantified using a mass spectral library search, accurate mass ion and N‐rules of a molecular formula for nitrogen compounds. Finally, a comparison of the low temperature solvent extraction method and Cambridge filter pad method indicated that more peaks, a higher peak volume and better repeatability were obtained using the low‐temperature solvent extraction method.     

Chemometrics comparison of gas chromatography with mass spectrometry and comprehensive two‐dimensional gas chromatography with time‐of‐flight mass spectrometry Daphnia magna metabolic profiles exposed to salinity

The performances of gas chromatography with mass spectrometry and of comprehensive two‐dimensional gas chromatography with time‐of‐flight mass spectrometry are examined through the comparison of Daphnia magna metabolic profiles. Gas chromatography with mass spectrometry and comprehensive two‐dimensional gas chromatography with mass spectrometry were used to compare the concentration changes of metabolites under saline conditions. In this regard, a chemometric strategy based on wavelet compression and multivariate curve resolution–alternating least squares is used to compare the performances of gas chromatography with mass spectrometry and comprehensive two‐dimensional gas chromatography with time‐of‐flight mass spectrometry for the untargeted metabolic profiling of Daphnia magna in control and salinity‐exposed samples. Examination of the results confirmed the outperformance of comprehensive two‐dimensional gas chromatography with time‐of‐flight mass spectrometry over gas chromatography with mass spectrometry for the detection of metabolites in D. magna samples. The peak areas of multivariate curve resolution–alternating least squares resolved elution profiles in every sample analyzed by comprehensive two‐dimensional gas chromatography with time‐of‐flight mass spectrometry were arranged in a new data matrix that was then modeled by partial least squares discriminant analysis. The control and salt‐exposed daphnids samples were discriminated and the most relevant metabolites were estimated using variable importance in projection and selectivity ratio values. Salinity de‐regulated 18 metabolites from metabolic pathways involved in protein translation, transmembrane cell transport, carbon metabolism, secondary metabolism, glycolysis, and osmoregulation.     

Determination of volatile organic compounds in urban and industrial air from Tarragona by thermal desorption and gas chromatography-mass spectrometry

This study describes the optimisation of an analytical method to determine 54 volatile organic compounds (VOCs) in air samples by active collection on multisorbent tubes, followed by thermal desorption and gas chromatography-mass spectrometry. Two multisorbent beds, Carbograph 1/Carboxen 1000 and Tenax/Carbograph 1TD, were tested. The latter gave better results, mainly in terms of the peaks that appeared in blank chromatograms. Temperatures, times and flow desorption were optimised. Recoveries were higher than 98.9%, except methylene dichloride, for which the recovery was 74.9%. The method's detection limits were between 0.01 and 1.25 μg m⁻³ for a volume sample of 1200 ml, and the repeatability on analysis of 100 ng of VOCs, expressed as relative standard deviation for n = 3, was lower than 4% for all compounds. Urban and industrial air samples from the Tarragona region were analysed. Benzene, toluene, ethylbenzene and xylenes (BTEX) were found to be the most abundant VOCs in urban air. Total VOCs in urban samples ranged between 18 and 307 μg m⁻³. Methylene chloride, 1,4-dichlorobenzene, chloroform and styrene were the most abundant VOCs in industrial samples, and total VOCs ranged between 19 and 85 μg m⁻³.     

Use of a recently developed thermal modulator within the context of comprehensive two‐dimensional gas chromatography combined with time‐of‐flight mass spectrometry: Gas flow optimization aspects

The present research is based on the use of a recently developed comprehensive two‐dimensional gas chromatography thermal modulator, which is defined as solid‐state modulator. The transfer device was installed on top of a single gas chromatography oven, while benchtop low‐resolution time‐of‐flight mass spectrometry was used to monitor the compounds exiting the second analytical column. The solid‐state modulator was first described by Luong et al. in 2016, and it is a moving modulator that does not require heating and cooling gases to generate comprehensive two‐dimensional gas chromatography data. The accumulation and remobilization steps occur on a trapping capillary, this being subjected to thermoelectric cooling and micathermic heating. In this study, the effects of the gas linear velocity on the modulation performance were evaluated by using two different uncoated trapping capillaries, viz., 0.8 m × 0.25 mm id and 0.8 m × 0.20 mm id. Solid‐state modulator applications were carried out on a standard solution containing n‐alkanes (C_9, C_10, C₁₂), and on a sample of diesel fuel. The results indicated that the type of trapping capillary and gas velocity have a profound effect on modulation efficiency.     

Qualitative screening for volatile organic compounds in human blood using solid‐phase microextraction and gas chromatography‐mass spectrometry

A fast and simple screening procedure using solid‐phase microextraction and gas chromatography‐mass spectrometry (SPME‐GC‐MS) in full‐scan mode for the determination of volatile organic compounds (VOC) is presented. The development of a fast and simple screening technique for the simultaneous determination of various volatiles is of great importance, because of their widespread use, frequent occurrence in forensic toxicological questions and the fact that there is often no hint on involved substances at the crime scene. To simulate a screening procedure, eight VOC with different chemical characteristics were chosen (isoflurane, halothane, hexane, chloroform, benzene, isooctane, toluene and xylene). To achieve maximum sensitivity, variables that influence the SPME process, such as type of fiber, extraction and desorption temperature and time, agitation and additives were optimized by preliminary studies and by means of a central composite design. The limits of detection and recoveries ranged from 2.9 µg/l (xylene) to 37.1 µg/l (isoflurane) and 7.9% (chloroform) to 61.5% (benzene), respectively. This procedure can be used to answer various forensic and toxicological questions. The short time taken for the whole analytical procedure may make its eventual adoption for routine analysis attractive. Copyright © 2010 John Wiley & Sons, Ltd.     

Chemical differentiation of volatile compounds in crude and processed Atractylodis Macrocephalae Rhizoma by using comprehensive two‐dimensional gas chromatography with time‐of‐flight mass spectrometry combined with multivariate data analysis

In the present study, comprehensive 2D GC—TOF‐MS combined with multivariate data analysis was applied to analyze the differences of the volatile components in crude and processed Atractylodis Macrocephalae Rhizoma (AMR) samples. As a result, 26 compounds that were found in crude AMR samples disappeared in processed AMR samples, and 19 compounds were newly generated and identified in AMR after processing with wheat bran. Meanwhile, principal component analysis demonstrated that there were significant chemical differences between crude and processed AMR samples, and processing procedure caused obvious quantitative and qualitative changes of volatile components in AMR. The established method could be used to explain the chemical differentiation between crude and processed AMR, and to further understand the processing mechanism of herbal medicines.     

热脱附-气相色谱-三重四极杆串联质谱法测定环境空气中的挥发性有机物

采用热脱附(TD)结合气相色谱-三重四极杆串联质谱(GC-MS/MS)建立了环境空气中23种挥发性有机物(VOCs)同时检测的分析方法。空气样品通过主动采样的方式富集到装有Tenax-TA填料的热脱附管中,热解吸后在选择反应监测(SRM)模式下用GC-MS/MS进行检测,内标法定量。结果表明,23种VOCs在0.01~1 ng和1~100 ng低、高两个范围内线性关系良好,相关系数(r²)均大于0.99,方法定量限为0.00008~1 μ g/m³。加标水平为2、10和50 ng时,23种VOCs的平均回收率为77%~124%。除了最低加标水平的氯苯,相对标准偏差(RSD, n=6)均小于20%。对市内3个采样点的环境空气进行测定,其中苯、甲苯、乙苯、二甲苯、苯乙烯、1,2,4-三甲基苯和六氯丁二烯均有检出。实验证明,该TD和GC-MS/MS相结合的检测方法具有准确、可靠、灵敏度高等优点,适用于环境空气中VOCs的同时测定。     

The detection of various opiates and benzodiazepines by comprehensive two‐dimensional gas chromatography/time‐of‐flight mass spectrometry

A technique using comprehensive two‐dimensional gas chromatography/time‐of‐flight mass spectrometry (GC × GC/TOFMS) is applied to qualitative and quantitative drug testing. Human serum was ‘spiked’ with known quantities of benzodiazepines and a ‘street heroin’ mixture including some of the major metabolites and impurities. The sample components were extracted from the matrix by solid‐phase extraction (SPE). Constituents containing polar hydroxyl and/or secondary amine groups were derivatised with N‐methyl‐N‐(tert‐butyldimethyl)trifluoroacetamide (MTBSTFA) to improve the chromatographic performance. An orthogonal separation of the matrix constituents was achieved by coupling a DB‐5ms (5% phenyl) to a BPX50 (50% phenyl) GC column. The eluant was focused onto the second column by a twin‐stage cryo‐modulator. Rapid 6 s modulation times were achieved by transfer from a 30 m × 0.25 mm (length × internal diameter) to a 2 m × 0.1 mm column. TOFMS with rapid spectral acquisition (≤500 spectra/s) was employed in the mass range m/z 40–650. A clean mass spectrum was obtained for each analyte using mass spectral deconvolution software. The sensitivity and repeatability of the method were evaluated by the preparation of calibration standards for two benzodiazepines, flunitrazepam and its major metabolite 7‐aminoflunitrazepam (7‐amino‐FN), in the concentration range 5–1000 ng/mL. The limits of detection (LODs) and limits of quantitation (LOQs), calculated by repeat injections (×10) of the lowest standard, were 1.6 and 5.4 ng/mL (flunitrazepam); 2.5 and 8.5 ng/mL (7‐amino‐FN), respectively. There is scope to extend this protocol to screen a large number of drugs and metabolites stored in a library database. Copyright © 2009 John Wiley & Sons, Ltd.     

Coupling needle‐trap devices with comprehensive two‐dimensional gas chromatography with high‐resolution time‐of‐flight mass spectrometry to rapidly reveal the chemical transformation of volatile components from sulfur‐fumigated ginseng

Sulfur‐fumigation could alter the quality of white ginseng by damaging the bioactive compounds and generating sulfur‐containing materials. In the present study, coupling needle‐trap devices with comprehensive two‐dimensional gas chromatography and high‐resolution time‐of‐flight mass spectrometry was applied to rapidly reveal chemical transformation of volatile components from sulfur‐fumigated ginseng. Thirty‐two volatile compounds were not in white ginseng samples after sulfur‐fumigation. Furthermore, 20 sulfur‐containing compounds were identified for the first time in volatile oil of sulfur‐fumigated white ginseng. The established approach could be applied to discriminate sulfur‐fumigated white ginseng among commercial samples and to control the quality of white ginseng.     

Determination of volatile organic compounds in industrial wastewater plant air emissions by multi-sorbent adsorption and thermal desorption-gas chromatography-mass spectrometry

This paper describes the process of determining the presence of volatile organic compounds in air emissions from industrial wastewater treatment plants (WWTP). The analytical method, based on thermal desorption-gas chromatography-mass spectrometry, was developed to simultaneously determine of 99 volatile organic compounds (VOCs) in air samples. This method is rapid, environmentally-friendly (since no organic solvents are used to extract the analytes) and compatible with a large range of thermally stable polar and apolar compounds. The target VOCs were selected on the basis of their occurrence in real samples and their adverse effects on the environment and human health. To cover the wide range of target compounds, multisorbent tubes filled with Tenax TA and Carbograph 1TD were used. Method validation showed good repeatabilities, low detection limits, a high linear range and good recoveries. At a fixed sample volume of 600?mL no significant losses for any of the target compounds were found in the samples. Stability during storage indicated that samples must be keep refrigerated at 4°C and analysed within three days of collection. Real samples were taken from air emissions of an industrial wastewater treatment plant located in the Southern Industrial Area of Tarragona (Spain) with the aim of studying its contribution as a source of atmospheric VOCs. This WWTP collects wastewater from several chemical factories which produce isocyanates, polyurethanes, chlorinated organics and functional chemicals among other products. Samples from the collecting tank after the primary sedimentation showed higher VOC concentrations than samples from the secondary treatment tank. The most abundant VOCs found in these emissions are included in the USEPA List of Hazardous Air Pollutants. The highest values correspond to acrylonitrile (up to 1843?µg?m^?3) and styrene (up to 573.70?µg?m^?3). The levels of chloroform, 1,4-dioxane, ethylbenzene, 1,2,3-trimethylbenzene and 1,4-diethylbenzene were also high.     

A purge and trap technique to capture volatile compounds combined with comprehensive two‐dimensional gas chromatography/time‐of‐flight mass spectrometry to investigate the effect of sulfur‐fumigation on Radix Angelicae Dahuricae

Sulfur‐fumigation is known to reduce volatile compounds that are the main active components in herbs used in herbal medicine. We investigated changes in chemical composition between sun‐dried and sulfur‐fumigated Radix Angelicae Dahuricae using a purge and trap technique to capture volatile compounds, and two‐dimensional gas chromatography/time‐of‐flight mass spectrometry for identification. Using sun‐dried Radix Angelicae Dahuricae samples as a reference, the results showed that 73 volatile compounds, including 12 sulfide compounds, were found to be present only in sulfur‐fumigated samples. Furthermore, 32 volatile compounds that were found in sun‐dried Radix Angelicae Dahuricae samples disappeared after sulfur‐fumigation. The proposed method can be applied to accurately discriminate sulfur‐fumigated Radix Angelicae Dahuricae from different commercial sources. Copyright © 2014 John Wiley & Sons, Ltd.     

Determination and comparison of agarwood from different origins by comprehensive two‐dimensional gas chromatography–quadrupole time‐of‐flight mass spectrometry

Agarwood, a species of resinous heartwood, is a precious medicinal plant and a type of rare natural spice, which is widely used in medicine, cosmetics, religious activities, and other fields. In this study, agarwood samples from eight different regions across four countries were analyzed by comprehensive two‐dimensional gas chromatography?quadrupole time‐of‐flight mass spectrometry. A total of 232 species were identified (the match factors of these compounds were above 750). The main compounds of agarwood are oxygenated sesquiterpenes and chromones. The compositions of India1 and Malaysia2 were significantly different from those of other samples, which might be attributed to the different production processes of agarwood. For further investigation, factor analysis was conducted for six agarwood samples. The results showed that the data classification possessed a regional characteristic; according to the retention time and relative content, characteristic compositions were determined by factor scores. Finally, the differences of characteristic compositions were simply analyzed, and the reasons were speculated.     

热脱附-气相色谱-质谱法测定环境空气中67种挥发性有机物

采用热脱附-气相色谱-质谱法,建立了同时分析环境空气中67种挥发性有机物的分析方法。对比了5种不同填充材料不锈钢吸附管对78种挥发性有机物的吸附能力。填充材料为Tenax TA和Carbograph 1TD的混合填料吸附管对分析物的捕集效果最好,在30 mL/min高纯He气持续吹脱45 min的情况下,未发生穿透（即穿透率小于10%）的化合物达67种,分析物的种类包括芳香烃、脂肪烃、卤代烃和含氧挥发性有机物等。优化了使用该吸附管测定67种目标物时的热脱附条件。在5~100 ng范围内,目标化合物的色谱响应值与其量间具有良好的线性关系,其相关系数（r）均在1.0000~0.9977之间。方法检出限为0.3~2.4 ng,以采样体积1 L计算,检出限为0.3~2.4 μg/m³。加标量为20 ng时,7次重复实验目标化合物回收率均在81.6%~114.9%之间,目标化合物的相对标准偏差为1.2%~10.1%。采用该方法对某车厢内空气进行了检测,检出了包括酯类、卤代烷烃、卤代烯烃以及芳香族化合物在内的19种目标化合物,其范围为1.1~84.1 μg/m³。该方法准确、可靠、灵敏度高,实现了对环境空气中67种目标污染物的准确定量。     

热脱附-气相色谱-质谱法应用于工业源废气中挥发性有机物的目标和非目标筛查

建立了固相吸附热脱附-气相色谱-质谱(TD-GC-MS)综合筛查工业源废气中挥发性有机物(VOCs)的方法。对两种型号的固相吸附管进行了比较,最终选择使用Tenax SS TD Tubes吸附管。气体样品以恒定流速通过吸附管,富集分析物,经热脱附后,用GC-MS进行检测,目标化合物以内标法定量,非目标化合物的含量以甲苯的响应系数计算。方法检出限为1.06~5.44 ng,以采样体积300 mL计算,目标化合物的检出限为0.004~0.018 mg/m~3。吸附管平均加标回收率为78.4%~89.4%,相对标准偏差为3.9%~14.4%(n=7)。应用该方法对大连市某垃圾焚烧发电厂排放的废气进行VOCs目标及非目标化合物综合筛查,共检出29种VOCs,其中仅5种VOCs为预先设定的目标化合物,另外24种为非目标化合物,5种目标化合物含量仅占所有检出物总量的26.7%。证明了工业源废气VOCs分析中非目标化合物筛查的重要性,该研究思路对完整测定工业源挥发性有机污染物分布具有一定的借鉴意义。     

Quantification of nitrogen compounds in diesel fuel samples by comprehensive two‐dimensional gas chromatography coupled with quadrupole mass spectrometry

Although several methods for the analysis of nitrogen compounds in diesel fuel have been described in the literature, the demand for rapid, sensitive, and robust analyses has increased in recent years. In this study, a comprehensive two‐dimensional gas chromatographic method was developed for the identification and quantification of nitrogen compounds in diesel fuel samples. The quantification was performed using the standard addition method and the analysis was conducted using comprehensive two‐dimensional gas chromatography coupled with fast quadrupole mass spectrometry. This study is the first to report quantification of nitrogen compounds in diesel fuel samples using the standard addition method without fractionation. This type of analysis was previously performed using many laborious separation steps, which can lead to errors and losses. The proposed method shows good linearity for target nitrogen compounds evaluated (m‐toluidine, 4‐ethylaniline, indole, 7‐methylindole, 7‐ethylindole, carbazole, isoquinoline, 4‐methylquinoline, benzo[h]quinolone, and acridine) over a range from 0.05 to 2.0 mg/L, and limits of detection and quantification of <0.06 and 0.16 mg/L, respectively, for all nitrogen compounds studied.