A Four‐Electron Sulfur Electrode Hosting a Cu2+/Cu+ Redox Charge Carrier

The elemental sulfur electrode with Cu²⁺ as the charge carrier gives a four‐electron sulfur electrode reaction through the sequential conversion of S?CuS?Cu₂S. The Cu‐S redox‐ion electrode delivers a high specific capacity of 3044 mAh g^?1 based on the sulfur mass or 609 mAh g^?1 based on the mass of Cu₂S, the completely discharged product, and displays an unprecedently high potential of sulfur/metal sulfide reduction at 0.5 V vs. SHE. The Cu‐S electrode also exhibits an extremely low extent of polarization of 0.05 V and an outstanding cycle number of 1200 cycles retaining 72 % of the initial capacity at 12.5 A g^?1. The remarkable utility of this Cu‐S cathode is further demonstrated in a hybrid cell that employs an Zn metal anode and an anion‐exchange membrane as the separator, which yields an average cell discharge voltage of 1.15 V, the half‐cell specific energy of 547 Wh kg^?1 based on the mass of the Cu₂S/carbon composite cathode, and stable cycling over 110 cycles.     

Development of Magnesium Anode-Based Transient Primary Batteries

Biodegradable primary batteries, also known as transient batteries, are essential to realize autonomous biodegradable electronic devices with high performance and advanced functionality. In this work, magnesium, copper, iron, and zinc – metals that exist as trace elements in the human body – were tested as materials for biomedical transient electronic devices. Different full cell combinations of Mg and X (where X = Cu, Fe, and Zn and the anodized form of the metals) with phosphate buffered saline (PBS) as electrolyte were studied. To form the cathodes, metal foils were anodized galvanostatically at a current density of 2.0 mA cm⁻² for 30 mins. Electrochemical measurements were then conducted for each electrode combination to evaluate full cell battery performance. Results showed that the Mg−Cu_anodized chemistry has the highest power density at 0.99 mW/cm². Nominal operating voltages of 1.26 V for the first 0.50 h and 0.63 V for the next 3.7 h were observed for Mg−Cu_anodized which was discharged at a current density of 0.70 mA cm⁻². Among the materials tested, Mg−Cu_anodized exhibited the best discharge performance with an average specific capacity of 2.94 mAh cm⁻², which is comparable to previous reports on transient batteries.     

Contribution from the ion-exchange factor to the potential of a copper-containing electron-ion exchanger

The process of formation of the electrode potential of EI-21 electron-ion exchanger, composed of ultrafine copper particles and KU-23 sulfocationite, was studied. The potentials of a EI-21 powdery electrode with a platinum lead in copper(II) sulfate solutions of various concentrations (0.005–1.0 M) were measured using currentless-mode potentiometry. The potential of this electrode first shifted by 0.02–0.15 V in the negative direction with respect to a compact copper electrode, after which the shift eventually decreased to ?0.010 ± 0.003 V. It was demonstrated that the time evolution of the potential is determined by the interplay of electron and ion exchange. When EI-21 is placed onto a platinum lead, the role of the potential-determining reaction passes from Cu²⁺ + e^? ? Cu⁺ to Cu²⁺ + 2e^? ? Cu. At the same time, H⁺-Cu²⁺ ion exchange gives rise to a change in the ratio of the concentration of copper(II) ions in the internal and external solutions. The Donnan potential, which arises at the boundary between the electron-ion exchanger and the external solution, maintains a high concentration of copper(II) ions in the internal solution, a factor that facilitates the recrystallization of the particle distributed over the bulk of the exchanger. The process of recrystallization slows down with time to such an extent that the electrode potential stops changing, remaining at a level close to the equilibrium potential of the Cu²⁺/Cu pair. It was concluded that the internal stability of the system makes the potential of the EI-21 electrode sensitive to the dispersity of the metal component and the concentration of potential-determining metal ions in the external solution.     

Effects of Conjugated Structure on the Magnesium Storage Performance of Dianhydrides

Inorganic cathodes of rechargeable Mg batteries suffer from limited selections, while organic materials provide more options. Herein, three conjugated dianhydrides, pyromellitic dianhydride, 1,4,5,8-naphthalenetetracarboxylic dianhydride and 3,4,9,10-perylenetetracarboxylic dianhydride are comparatively investigated to elucidate the effects of conjugated structure on the Mg²⁺ storage performances. It is observed that the reversible Mg²⁺ storage capacity is more dependent on the conjugated structure than carbonyl numbers. Ex-situ mechanism study illustrates that the extended conjugated structure delocalizes the electron density, hence enhancing carbonyl enolization and increasing the Mg²⁺ storage capacity. Furthermore, the largely conjugated structure buffers the charge density change during repeated magnesiation/demagnesiation resulting in better cyclability. Prominently, 3,4,9,10-perylenetetracarboxylic dianhydride shows a high Mg²⁺ storage capacity (160 mAh g⁻¹) and a good cycling stability (80 % capacity retention after 100 cycles) with the largest conjugated structure. This work provides a low-cost cathode for rechargeable Mg batteries that can be utilized for designing high-performance organic Mg battery cathodes.     

A Bipolar and Self‐Polymerized Phthalocyanine Complex for Fast and Tunable Energy Storage in Dual‐Ion Batteries

Bipolar redox organics have attracted interest as electrode materials for energy storage owing to their flexibility, sustainability and environmental friendliness. However, an understanding of their application in all‐organic batteries, let alone dual‐ion batteries (DIBs), is in its infancy. Herein, we propose a strategy to screen a variety of phthalocyanine‐based bipolar organics. The self‐polymerizable bipolar Cu tetraaminephthalocyanine (CuTAPc) shows multifunctional applications in various energy storage systems, including lithium‐based DIBs using CuTAPc as the cathode material, graphite‐based DIBs using CuTAPc as the anode material and symmetric DIBs using CuTAPc as both the cathode and anode materials. Notably, in lithium‐based DIBs, the use of CuTAPc as the cathode material results in a high discharge capacity of 236 mAh g^?1 at 50 mA g^?1 and a high reversible capacity of 74.3 mAh g^?1 after 4000 cycles at 4 A g^?1. Most importantly, a high energy density of 239 Wh kg^?1 and power density of 11.5 kW kg^?1 can be obtained in all‐organic symmetric DIBs.     

Realizing Complete Solid‐Solution Reaction in High Sodium Content P2‐Type Cathode for High‐Performance Sodium‐Ion Batteries

P2‐type layered oxides suffer from an ordered Na⁺/vacancy arrangement and P2→O2/OP4 phase transitions, leading them to exhibit multiple voltage plateaus upon Na⁺ extraction/insertion. The deficient sodium in the P2‐type cathode easily induces the bad structural stability at deep desodiation states and limited reversible capacity during Na⁺ de/insertion. These drawbacks cause poor rate capability and fast capacity decay in most P2‐type layered oxides. To address these challenges, a novel high sodium content (0.85) and plateau‐free P2‐type cathode‐Na_0.85Li_0.12Ni_0.22Mn_0.66O₂ (P2‐NLNMO) was developed. The complete solid‐solution reaction over a wide voltage range ensures both fast Na⁺ mobility (10^?11 to 10^?10 cm² s^?1) and small volume variation (1.7 %). The high sodium content P2‐NLNMO exhibits a higher reversible capacity of 123.4 mA h g^?1, superior rate capability of 79.3 mA h g^?1 at 20 C, and 85.4 % capacity retention after 500 cycles at 5 C. The sufficient Na and complete solid‐solution reaction are critical to realizing high‐performance P2‐type cathodes for sodium‐ion batteries.     

Safe,Low‐Cost,Fast‐Kinetics and Low‐Strain Inorganic‐Open‐Framework Anode for Potassium‐Ion Batteries

A key challenge for potassium‐ion batteries is to explore low‐cost electrode materials that allow fast and reversible insertion of large‐ionic‐size K⁺. Here, we report an inorganic‐open‐framework anode (KTiOPO₄), which achieves a reversible capacity of up to 102 mAh g^?1 (307 mAh cm^?3), flat voltage plateaus at a safe average potential of 0.82 V (vs. K/K⁺), a long lifespan of over 200 cycles, and K⁺‐transport kinetics ≈10 times faster than those of Na‐superionic conductors. Combined experimental analysis and first‐principles calculations reveal a charge storage mechanism involving biphasic and solid solution reactions and a cell volume change (9.5 %) even smaller than that for Li⁺‐insertion into graphite (≈10 %). KTiOPO₄ exhibits quasi‐3D lattice expansion on K⁺ intercalation, enabling the disintegration of small lattice strain and thus high structural stability. The inorganic open‐frameworks may open a new avenue for exploring low‐cost, stable and fast‐kinetic battery chemistry.     

Safe,Low‐Cost,Fast‐Kinetics and Low‐Strain Inorganic‐Open‐Framework Anode for Potassium‐Ion Batteries

A key challenge for potassium‐ion batteries is to explore low‐cost electrode materials that allow fast and reversible insertion of large‐ionic‐size K⁺. Here, we report an inorganic‐open‐framework anode (KTiOPO₄), which achieves a reversible capacity of up to 102 mAh g^?1 (307 mAh cm^?3), flat voltage plateaus at a safe average potential of 0.82 V (vs. K/K⁺), a long lifespan of over 200 cycles, and K⁺‐transport kinetics ≈10 times faster than those of Na‐superionic conductors. Combined experimental analysis and first‐principles calculations reveal a charge storage mechanism involving biphasic and solid solution reactions and a cell volume change (9.5 %) even smaller than that for Li⁺‐insertion into graphite (≈10 %). KTiOPO₄ exhibits quasi‐3D lattice expansion on K⁺ intercalation, enabling the disintegration of small lattice strain and thus high structural stability. The inorganic open‐frameworks may open a new avenue for exploring low‐cost, stable and fast‐kinetic battery chemistry.     

Multiple Active Sites: Lithium Storage Mechanism of Cu‐TCNQ as an Anode Material for Lithium‐Ion Batteries

Recently, carboxylate metal‐organic framework (MOF) materials were reported to perform well as anode materials for lithium‐ion batteries (LIBs); however, the presumed lithium storage mechanism of MOFs is controversial. To gain insight into the mechanism of MOFs as anode materials for LIBs, a self‐supported Cu‐TCNQ (TCNQ: 7,7,8,8‐tetracyanoquinodimethane) film was fabricated via an in situ redox routine, and directly used as electrode for LIBs. The first discharge and charge specific capacities of the self‐supported Cu‐TCNQ electrode are 373.4 and 219.4 mAh g^?1, respectively. After 500 cycles, the reversible specific capacity of Cu‐TCNQ reaches 280.9 mAh g^?1 at a current density of 100 mA g^?1. Mutually validated data reveal that the high capacity is ascribed to the multiple‐electron redox conversion of both metal ions and ligands, as well as the reversible insertion and desertion of Li⁺ ions into the benzene rings of ligands. This work raises the expectation for MOFs as electrode materials of LIBs by utilizing multiple active sites and provides new clues for designing improved electrode materials for LIBs.     

A Yolk–Shell Structured Silicon Anode with Superior Conductivity and High Tap Density for Full Lithium‐Ion Batteries

The poor cycling stability resulting from the large volume expansion caused by lithiation is a critical issue for Si‐based anodes. Herein, we report for the first time of a new yolk–shell structured high tap density composite made of a carbon‐coated rigid SiO₂ outer shell to confine multiple Si NPs (yolks) and carbon nanotubes (CNTs) with embedded Fe₂O₃ nanoparticles (NPs). The high tap density achieved and superior conductivity can be attributed to the efficiently utilised inner void containing multiple Si yolks, Fe₂O₃ NPs, and CNTs Li⁺ storage materials, and the bridged spaces between the inner Si yolks and outer shell through a conductive CNTs “highway”. Half cells can achieve a high area capacity of 3.6 mAh cm^?2 and 95 % reversible capacity retention after 450 cycles. The full cell constructed using a Li‐rich Li₂V₂O₅ cathode can achieve a high reversible capacity of 260 mAh g^?1 after 300 cycles.     

VOCl as a Cathode for Rechargeable Chloride Ion Batteries

A novel room temperature rechargeable battery with VOCl cathode, lithium anode, and chloride ion transporting liquid electrolyte is described. The cell is based on the reversible transfer of chloride ions between the two electrodes. The VOCl cathode delivered an initial discharge capacity of 189 mAh g^?1. A reversible capacity of 113 mAh g^?1 was retained even after 100 cycles when cycled at a high current density of 522 mA g^?1. Such high cycling stability was achieved in chloride ion batteries for the first time, demonstrating the practicality of the system beyond a proof of concept model. The electrochemical reaction mechanism of the VOCl electrode in the chloride ion cell was investigated in detail by ex situ X‐ray diffraction (XRD), infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and X‐ray photoelectron spectroscopy (XPS). The results confirm reversible deintercalation–intercalation of chloride ions in the VOCl electrode.     

Facile Synthesis of Nitrogen‐Containing Mesoporous Carbon for High‐Performance Energy Storage Applications

Porous carbon with high specific surface area (SSA), a reasonable pore size distribution, and modified surface chemistry is highly desirable for application in energy storage devices. Herein, we report the synthesis of nitrogen‐containing mesoporous carbon with high SSA (1390 m² g^?1), a suitable pore size distribution (1.5–8.1 nm), and a nitrogen content of 4.7 wt % through a facile one‐step self‐assembly process. Owing to its unique physical characteristics and nitrogen doping, this material demonstrates great promise for application in both supercapacitors and encapsulating sulfur as a superior cathode material for lithium–sulfur batteries. When deployed as a supercapacitor electrode, it exhibited a high specific capacitance of 238.4 F g^?1 at 1 A g^?1 and an excellent rate capability (180 F g^?1, 10 A g^?1). Furthermore, when an NMC/S electrode was evaluated as the cathode material for lithium–sulfur batteries, it showed a high initial discharge capacity of 1143.6 mA h g^?1 at 837.5 mA g^?1 and an extraordinary cycling stability with 70.3 % capacity retention after 100 cycles.     

Das Gleichgewicht des Cu2+−Cu+−Cu-systems in konzentrierten Perchloratlösungen

The equilibrium of the reaction Cu²⁺+Cu?2 Cu⁺ has been investigated in cone. solutions of Ca(ClO₄)₂. The apparent equilibrium constants of this reaction and the formal potentials of the Cu²⁺/Cu⁺, Cu²⁺/Cu and Cu⁺/Cu redox systems were determined. From these data the hydration numbers of the Cu²⁺ and Cu⁺ ions were estimated and the scheme of the reaction studied was proposed and discussed. In addition the equilibrium constants of the reaction Cu²⁺+Cu(Hg)?2 Cu⁺ were calculated and discussed.     

High capacity and cycling stability of poly(diaminoanthraquinone) as an organic cathode for rechargeable lithium batteries

Poly(1,5‐diaminoanthraquinone) is synthesized by oxidative polymerization of diaminoanthraquinone monomers and investigated as an organic host for Li‐storage reaction. Benefiting from its high density of redox‐active, Li⁺‐associable benzoquinone groups attached to conducting polyaniline backbones, this polymer undergoes its cathodic reaction predominately through Li⁺‐insertion/extraction processes, delivering a very high reversible capacity of 285 mAh g^?1. In addition, the PDAQ polymer cathode exhibits an excellent rate capability (125 mAh g^?1 at 800 mA g^?1) and a considerable cyclability with a capacity retention of ～160 mAh g^?1 over 200 cycles, possibly serving as a sustainable, high capacity Li⁺ host cathode for Li‐ion batteries. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 235–238     

A Dual Plating Battery with the Iodine/[ZnIx(OH2)4−x]2−x Cathode

Plating battery electrodes typically deliver higher specific capacity values than insertion or conversion electrodes because the ion charge carriers represent the sole electrode active mass, and a host electrode is unnecessary. However, reversible plating electrodes are rare for electronically insulating nonmetals. Now, a highly reversible iodine plating cathode is presented that operates on the redox couples of I₂/[ZnI_x(OH₂)_4?x]^2?x in a water‐in‐salt electrolyte. The iodine plating cathode with the theoretical capacity of 211 mAh g^?1 plates on carbon fiber paper as the current collector, delivering a large areal capacity of 4 mAh cm^?2. Tunable femtosecond stimulated Raman spectroscopy coupled with DFT calculations elucidate a series of [ZnI_x(OH₂)_4?x]^2?x superhalide ions serving as iodide vehicles in the electrolyte, which eliminates most free iodide ions, thus preventing the consequent dissolution of the cathode‐plated iodine as triiodides.     

Strong Visible‐Light‐Absorbing Cuprous Sensitizers for Dramatically Boosting Photocatalysis

Developing strong visible‐light‐absorbing (SVLA) earth‐abundant photosensitizers (PSs) for significantly improving the utilization of solar energy is highly desirable, yet it remains a great challenge. Herein, we adopt a through‐bond energy transfer (TBET) strategy by bridging boron dipyrromethene (Bodipy) and a Cu^I complex with an electronically conjugated bridge, resulting in the first SVLA Cu^I PSs ( Cu‐2 and Cu‐3 ). Cu‐3 has an extremely high molar extinction coefficient of 162 260 m ^?1 cm^?1 at 518 nm, over 62 times higher than that of traditional Cu^I PS ( Cu‐1 ). The photooxidation activity of Cu‐3 is much greater than that of Cu‐1 and noble‐metal PSs (Ru(bpy)₃²⁺ and Ir(ppy)₃⁺) for both energy‐ and electron‐transfer reactions. Femto‐ and nanosecond transient absorption and theoretical investigations demonstrate that a “ping‐pong” energy‐transfer process in Cu‐3 involving a forward singlet TBET from Bodipy to the Cu^I complex and a backward triplet‐triplet energy transfer greatly contribute to the long‐lived and Bodipy‐localized triplet excited state.     

Remarkably improved cycling stability of 3D porous Cu–Sn anode for lithium-ion full cells by adjusting working voltage range

Numerous studies confirm that three dimensional porous Cu–Sn (3DP Cu–Sn) anode possesses good application prospect in light of its desirable electrochemical performance on lithium ion half cells, but there are a few related systematic researches on lithium ion full cells until now, which is indispensable before its commercialization. Herein, the effects of galvanostatic charge-discharge voltage range on the cycling stability of 3DP Cu–Sn anode for lithium ion full cells are investigated systematically. The results show that the suitable charge-discharge voltage range plays a key role in improving the reversible capacity and cycling stability of the 3DP Cu–Sn||LiCoO₂ full cell, which is closely related to maintaining the electrode structure stable by controlling the amount of Li⁺ extracted and inserted. Especially, in the voltage range of 1.2–3.9 ​V, the full cell exhibits remarkably improved electrochemical properties with the high initial reversible capacity of 2.71 ​mAh cm⁻² and 71.95% capacity retention upon 80 cycles. We believe that this work can provide a significant reference for the practical application of porous Sn-based anodes.     

Self‐Supported Cu3P Nanowire Arrays as an Integrated High‐Performance Three‐Dimensional Cathode for Generating Hydrogen from Water

Searching for inexpensive hydrogen evolution reaction (HER) electrocatalysts with high activity has attracted considerable research interest in the past years. Reported herein is the topotactic fabrication of self‐supported Cu₃P nanowire arrays on commercial porous copper foam (Cu₃P NW/CF) from its Cu(OH)₂ NW/CF precursor by a low‐temperature phosphidation reaction. Remarkably, as an integrated three‐dimensional hydrogen‐evolving cathode operating in acidic electrolytes, Cu₃P NW/CF maintains its activity for at least 25 hours and exhibits an onset overpotential of 62 mV, a Tafel slope of 67 mV dec^?1, and a Faradaic efficiency close to 100 %. Catalytic current density can approach 10 mA cm^?2 at an overpotential of 143 mV.     

Voltammetry and EQCM Investigation of Glutathione Monolayer and Its Complexation with Cu2+

The glutathione (GSH) self‐assembled monolayer and its compexlation with Cu²⁺ were studied by using voltammetry and EQCM. It was found that the monolayer could rearrange during the redox process of Cu²⁺/Cu⁺. The protonating, or not, of the carboxyl terminates of the adsorpted GSH molecules influence the compexlation interaction significantly for they are the key binding sites. The GSH monolayer had the capacity to accumulate Cu²⁺ and the monolayer modified gold electrode was employed to detect the low levels of Cu²⁺ with a limit of 1.0×10^?10 mol L^?1.     

Electrochemical production of NH2• radicals by the system Cu2+/VO2+/NH2OH and their reactions with benzene and toluene

Electroinitiated production of NH₂^. radicals was demonstrated to occur in aqueous acid solution when in the system Cu²⁺/VO²⁺/NH₂OH Cu²⁺ is reduced to metallic copper on a mercury cathode. The first stage of this process involves the reduction of vanadyl to V³⁺ by metallic copper. The electrochemical system Cu²⁺/VO²⁺ was demonstrated to follow a depolarization scheme of the type of the catalyzed electrode process.For the reaction Cu+2 VO²⁺k₁→Cu²⁺+2 V³⁺ a k₁ value of 32 M^?1 s^?1 at 50°C was calculated.The second stage of the process is the reduction of NH₂OH by V³⁺ to give aminyl radicals. In presence of benzene and toluene these radicals add to the aromatic ring to give new radicals which are oxidized by Cu²⁺ to the corresponding amines.The cuzrent yield of this process attains values as high as 70%. The yield dependence on H₂SO₄ concentration, electrolytic current and dioxane concentration is discussed.