Stripping Voltammetry of Cerium(IIl) with a Chemically Modified Carbon Paste Electrode Containing Functionalized Nanoporous Silica Gel

This research introduces the design of an adsorptive stripping voltammetric method for the cerium(III) determination at a carbon paste electrode, chemically modified with dipyridyl‐functionalized nanoporous silica gel (DPNSG‐CPE). The electroanalytical procedure comprised two steps: the Ce(III) chemical accumulation at ?200 mV followed by the electrochemical detection of the Ce(III)/dipyridyl complex, using anodic stripping voltammetry. The factors, influencing the adsorptive stripping performance, were optimized including the modifier quantity in the paste, the electrolyte concentrations, the solution pH and the accumulation potential or time. The resulting electrode demonstrated a linear response over a wide range of Ce(III) concentration (1.0–28 ng mL^?1). The precision for seven determinations of 4 and 10 ng mL^?1 Ce(III) was 3.2% and 2.5% (relative standard deviation), respectively. The prepared electrode was used for the cerium determination in real samples and very good recovery results were obtained.     

Electrochemical preparation of a novel type of C-dots/ZrO2 nanocomposite onto glassy carbon electrode for detection of organophosphorus pesticide

A selective, sensitive novel electrochemical sensor for detection of methyl parathion on the preparation of a carbon dots (C-dots)/ZrO₂ nanocomposite was developed. The C-dots/ZrO₂ nanocomposite was fabricated using electrochemical deposition onto a glassy carbon electrode and characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and cyclic voltammetry. The optimum parameters such as effect of pH, accumulation time, accumulation potential, scan rate, effect of amount of C-dots and effect of amount of ZrO₂ were investigated. The C-dots/ZrO₂ modified glassy carbon electrode allowed rapid, selective determination of methyl parathion in rice samples by adsorptive stripping voltammetry. The stripping response was highly linear over the methyl parathion concentrations ranging from 0.2 ng mL^?1 to 48 ng mL^?1, with a detection limit of 0.056 ng mL^?1. This novel electrochemical nanocomposite-based electrochemical sensor was successfully applied for the detection of methyl parathion in rice samples.     

Synthesis and application of a natural-based nanocomposite with carbon nanotubes for sensitive voltammetric determination of lead (II) ions

ABSTRACT

A modified carbon paste electrode has been developed for the determination of Pb(ΙΙ) ions based on Fe₃O₄/eggshell magnetic nanocomposite. The structure and morphology of Fe₃O₄/eggshell were analysed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The prepared nanocomposite was also characterized by Fourier transform infrared spectroscopy (FT-IR) and vibrating sample magnetometer (VSM). The electrochemical procedure was based on the accumulation and determination of Pb(ΙΙ) ions at the surface of the modified carbon paste electrode with Fe₃O₄/eggshell nanocomposites and carbon nanotubes by differential pulse anodic stripping voltammetry (DPASV). Various experimental parameters involved in the preconcentration of Pb(ΙΙ) ions and voltammetric stripping step were studied. Under the optimum conditions, the voltammetric peak current of Pb(ΙΙ) occurs at a potential about ?0.5 V. Also, the voltammetric peak current increased linearly with Pb(ΙΙ) concentration in the range of 0.5–200 ng mL^?1 and a detection limit of 0.15 ng mL^?1 was obtained for Pb(ΙΙ). The selectivity of the proposed electrode for Pb(ΙΙ) ions in the presence of some cations was also examined. The practical application of the proposed modified electrode was evaluated by the determination of Pb(ΙΙ) ions in human hair and water samples. The results were satisfactory for the spiked samples.     

The determination of acetaminophen using a carbon nanotube:graphite-based electrode

The oxidation of acetaminophen was studied at a glassy carbon electrode modified with multi-walled carbon nanotubes and a graphite paste. Cyclic voltammety, differential pulse voltammetry and square wave voltammetry at various pH values, scan rates, and the effect of the ratio of nanotubes to graphite were investigated in order to optimize the parameters for the determination of acetaminophen. Square wave voltammetry is the most appropriate technique in giving a characteristic peak at 0.52 V at pH 5. The porous nanostructure of the electrode improves the surface area which results in an increase in the peak current. The voltammetric response is linear in the range between 75 and 2000 ng.mL^?1, with standard deviations between 0.25 and 7.8%, and a limit of detection of 25 ng.mL^?1. The method has been successfully applied to the analysis of acetaminophen in tablets and biological fluids.     

Enhanced sensing of anthraquinone dyes using multiwalled carbon nanotubes modified electrode

The voltammetric behaviour of two anthraquinone dyes such as Alizarin Red S (ARS) and Reactive blue 4 (RB4) was investigated at plain glassy carbon electrode (GCE), multiwalled carbon nano tube modified GCE (MWCNT/GCE) and zeolite modified GCE (ZE/GCE) using cyclic voltammetry. Effects of pH, scan rate and concentration were studied. The surface morphology of the modified electrode in the absence and presence of dye molecules was characterized by scanning electron microscopy (SEM). A systematic study on the variation of experimental parameters with differential pulse stripping voltammetry (DPSV) was carried out and the optimized experimental conditions were arrived. MWCNT/GCE performed well among the three electrode systems and the limit of detection (LOD) was 0.036?µg?mL^?1 for ARS and 0.05?µg?mL^?1 for RB4 on this modified system. Suitability of the differential pulse stripping voltammetric method for the trace determination of textile dyes in effluents was also realized.     

Construction of Modified Carbon Paste Electrode for Highly Sensitive Simultaneous Electrochemical Determination of Trace Amounts of Copper (II) and Cadmium (II)

A chemically modified electrode was constructed for rapid, simple, accurate, selective and highly sensitive simultaneous determination of Cu(II) and Cd(II) using square wave anodic stripping voltammetry. The electrode was prepared by incorporation of SiO₂ nanoparticles, coated with a newly synthesized Schiff base, in carbon paste electrode. The limit of detection was found to be 0.28 ng mL^?1 and 0.54 ng mL^?1 for Cu(II) and Cd(II), respectively. The proposed chemically modified electrode was used for the determination of copper and cadmium in several foodstuffs and water samples.     

Electrocatalytic Investigations of Cu(II) and Fe(III) Complexes of Salophen Derivative Schiff Bases on the Pencil Graphite Electrode

This present study describes a pencil graphite electrode surface covered with Cu(II) and Fe(III) complexes based on Salophen derivative Schiff bases in acetonitrile solution containing LiClO₄ as a supporting electrolyte. Cyclic voltammetry method was used for the surface modification procedure with 25 cycle at a sweep rate of 50 mV s^?1. Some characterization methods were used to identify of the prepared modified surfaces including cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), Ultraviolet‐visible Spectroscopy (UV‐Vis), and Scanning Electron Microscopy/Energy Dispersive X‐ray Spectroscopy (SEM/SEM‐EDX). The catalytic activity of these modified surfaces on the electrochemical oxidation of catechol (CC) was investigated and they compared with each other. The results demonstrated that these modified electrodes showed perfect electrocatalytic activity on the catechol determination, however the modified electrode prepared with the Cu(II) complex has higher catalytic activity than this prepared with the Fe(III) complex thanks to its the lower detection limit.     

Voltammetric Behavior of Osmium‐Labeled DNA at Mercury Meniscus‐Modified Solid Amalgam Electrodes. Detecting DNA Hybridization

The complex of osmium tetroxide with 2,2′‐bipyridine has been utilized as a probe of DNA structure and an electroactive marker of DNA in DNA hybridization sensors. It produces several voltammetric signals, the most negative of them has been observed only at mercury electrodes. This signal is of catalytic nature affording a high sensitivity of DNA determination. The catalytic current due to evolution of hydrogen in voltammetry of DNA modified by complex of osmium tetroxide with 2,2′‐bipyridine (DNA‐Os,bipy) was studied. Solid amalgam electrodes (modified with mercury menisci) of silver (m‐AgSAE), copper (m‐CuSAE), gold, and of combined bismuth and silver, were used as possible substitutes for mercury electrodes. Besides the hanging mercury drop electrode (HMDE), the catalytic current was observed only on m‐AgSAE and m‐CuSAE. Electrodes of gold and bismuth amalgams did not give the catalytic current. The detection limit of DNA‐Os,bipy on HMDE was 0.1 ng mL^?1 (RSD=2.3 %, N=11), and on m‐AgSAE 0.2 ng mL^?1 (RSD=3.1%, N=11). The m‐AgSAE was successfully applied as a detection electrode in double‐surface DNA hybridization experiments offering highly specific discrimination between complementary (target) and nonspecific DNAs, as well as determination of the length of a repetitive DNA sequence. The m‐AgSAE has proved a convenient alternative to the HMDE or carbon electrodes used for similar purposes in previous work.     

Development and application of the tartrazine voltammetric sensors based on molecularly imprinted polymers

A modified glassy carbon electrode was prepared as an electrochemical voltammetric sensor based on molecularly imprinted polymer film for tartrazine (TT) detection. The sensitive film was prepared by copolymerization of tartrazine and acrylamide on the carbon nanotube-modified glassy carbon electrode. The performance of the imprinted sensor was investigated by cyclic voltammetry, differential pulse voltammetry, and electrochemical impedance spectroscopy in detail. Under the optimum conditions, two dynamic linear ranges of 8?×?10^?8 to 1?×?10^?6?mol?L^?1 and 1?×?10^?6 to 1?×?10^?5?mol?L^?1 were obtained, with a detection limit of 2.74?×?10^?8?mol?L^?1(S/N?=?3). This sensor was used successfully for tartrazine determination in beverages.     

Utilisation of polypyrrole modified electrode for the determination of pesticides

Cyclic voltammetric studies of isoproturon and carbendazim using polypyrrole modified glassy carbon electrode were carried out. The electrode and reaction conditions, which yielded maximum current signal, were selected for the development of stripping voltammetric procedure for the determination of the pesticides. The oxidation peak around 1.3?V obtained for isoproturon and carbendazim while employing polypyrrole modified electrode showed maximum current response. This peak was chosen for stripping analysis using square wave mode. The experimental parameters were optimized and the calibration plot was obtained. The LOD was 0.5?ng?mL^?1 for isoproturon and 5?ng?mL^?1 for carbendazim. The relative standard deviation for 5 identical measurements was 2.81% and 3.33% for isoproturon and carbendazim respectively. The applicability of the method was verified by determining the pesticides in spiked soil and water samples.     

Fe3O4 Nanorods-RGO-ionic Liquid Nanocomposite Based Electrochemical Sensor for Aflatoxin B1 in Ground Paprika

A novel and sensitive method for the determination of aflatoxin B1 (AFA−B1) in ground paprika using a methyltrioctylammonium chloride ionic liquid (IL), iron oxide nanorods (Fe₃O₄ nanorods) and reduced graphene oxide (RGO) fabricated glassy carbon electrode (GCE) was developed. The synthesized nanoparticles, nanocomposites and modified electrode surfaces were characterized by Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), thermogravimetric analysis (TGA/DSC) and x-ray diffraction (XRD) analyses. Moreover, the electrochemical performance of the developed sensor was determined by cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The obtained results demonstrate that the sensitivity of AFA−B1 is significantly enhanced on RGO-Fe₃O₄ nanorods-IL-GCE in comparison with bare GCE, RGO-GCE and RGO-Fe₃O₄ nanorods-GCE. The redox peak currents of AFA−B1 exhibited good linear relationship with its concentration in the range from 0.02 to 0.33 ng mL⁻¹ with detection limit of (LOD) 0.03 ng mL⁻¹ and limit of quantification (LOQ) 0.36 ng mL⁻¹ respectively (S/N=3). In addition, the fabricated electrode showed good stability and reproducibility. The proposed technique was effectively applied to identify the AFA−B1 in real ground paprika samples with acceptable results.     

A Selective Voltammetric Method for Uric Acid Detection at a Glassy Carbon Electrode Modified with Electrodeposited Film Containing DNA and Pt‐Fe(III) Nanocomposites

A novel biosensor by electrochemical codeposited Pt‐Fe(III) nanocomposites and DNA film was constructed and applied to the detection of uric acid (UA) in the presence of high concentration of ascorbic acid (AA). Based on its strong catalytic activity toward the oxidation of UA and AA, the modified electrode resolved the overlapping voltammetric response of UA and AA into two well‐defined peaks with a large anodic peak difference (ΔE_pa) of about 380mV. The catalytic peak current obtained from differential pulse voltammetry (DPV) was linearly dependent on the UA concentration from 3.8×10^?6 to 1.6×10^?4 M (r=0.9967) with coexistence of 5.0×10^?4 M AA. The detection limit was 1.8×10^?6 M (S/N=3) and the presence of 20 times higher concentration of AA did not interfere with the determination. The modified electrode shows good sensitivity, selectivity and stability.     

Anodic stripping voltammetry of silver(I) using a carbon paste electrode modified with multi-walled carbon nanotubes

We describe a silver(I)-selective carbon paste electrode modified with multi-walled carbon nanotubes and a silver-chelating Schiff base, and its electrochemical response to Ag(I). Effects of reduction potential and time, accumulation time, pH of the solution and the stripping medium were studied by differential pulse anodic stripping voltammetry and optimized. The findings resulted in a method for the determination of silver over a linear response range (from 0.5 to 235 ng?mL^?1) and with a detection limit as low as 0.08 ng?mL^?1. The sensor displays good repeatability (with the RSD of ±?2.75 % for 7 replicates) and was applied to the determination of Ag(I) in water samples and X-ray photographic films.

A Selective Film Based on Poly(3‐octylthiophene) Doped with Dihydroxyanthraquinone Sulfonate

A stable film of poly(3‐octylthiophene)–dihydroxyanthraquinone sulfonate has been synthesized electrochemically in non‐aqueous solution. The incorporation of dihydroxyanthraquinone sulfonate as an anionic complexing ligand into poly(3‐octylthiophene) film during electropolymerization was achieved and copper ions were accumulated by reduction on the electrode surface. The presence of dihydroxyanthraquinone sulfonate during the electrochemical polymerization of 3‐octylthiophene is shown to impact the sensitivity and the stability of the organic conducting film electrode response. The electroanalysis of copper(II) ions using conducting polymer electrode was achieved by differential pulse anodic stripping voltammetry with remarkable selectivity. The analytical performance was evaluated and linear calibration graphs were obtained in the concentration range of 50–400 ng mL^?1 copper(II) ion for 240 seconds accumulation time and the limit of detection was found to be 7.8 ng mL^?1. To check the selectivity of the proposed stripping voltammetric method for copper(II) ion, various metal ions as potential interferents were tested. The developed method was applied to copper(II) determination in certified reference material, NWRI‐TMDA‐61, trace elements in fortified water.     

Development of a Carbon Nanotube Modified Ionic Liquid Electrode for the Voltammetric Determination of Methyldopa Levels in Urine

A glassy carbon electrode was modified with carbon nanotubes and the ionic liquid N‐butyl pyridinium trifluoromethyl methanesulfonate for the determination of methyldopa in urine samples. Methyldopa exhibited a well‐defined anodic signal over a broad pH range of 2–10 and the peak current increased approximately 100 fold over that of the unmodified electrode. Accordingly, a novel method for the determination of methyldopa was proposed using differential pulse voltammetry. The peak current was linear over a methyldopa concentration range from 21 to 2111 ng mL^?1 with a LOD of 6.9 ng mL^?1 and a LOQ of 7.4 ng mL^?1. The method was applied to determine the excretion profile of methyldopa in urine without sample pretreatment.     

Lead ion sensor with electrodes modified by imidazole-functionalized polyaniline

Glassy carbon electrodes (GCE) and carbon paste electrodes (CPE) were modified with imidazole functionalized polyaniline with the aim to develop a sensor for lead (II) in both acidic and basic aqueous solution. The electrodes were characterized by cyclic voltammetry and differential pulse adsorptive stripping voltammetry. The limit of detections obtained with glassy carbon electrode and carbon paste electrode are 20?ng?mL^-1 and 2?ng?mL^-1 of lead ion, respectively. An interference study was carried out with Cd(II), As(III), Hg(II) and Co(II) ions. Cd(II) ions interfere significantly (peak overlap) and As(III) has a depressing effect on the lead signal. The influence of pH was investigated indicating that bare and modified GCE and CPE show optimum response at pH?4.0 ± 0.05.

Amperometric Sensor for Trichloroacetic Acid Based on Myoglobin/Colloidal Gold Nanoparticles Immobilized in Titania Sol–Gel Matrix

A new amperometric sensor for the determination of trichloroacetic acid (TCA) was developed based on the immobilization of myoglobin/colloidal gold nanoparticles in titania sol–gel matrix. The sensor showed a pair of well‐defined and nearly reversible cyclic voltammetric peaks for the Mb Fe(III)/Fe(II) with a formal potential (E°′) of ?335 mV and a peak‐to‐peak separation was 61 mV vs. Ag/AgCl (3.0 M KCl) at 100 mV s^?1 in 0.1 M pH 7.0 phosphate buffer solutions (PBS). The formal potential of the Mb Fe(III)/Fe(II) couple shifted linearly with the pH with a slope of ?51.3 mV/pH, indicating that an electron transfer accompanies single‐proton transportation. The sensor displayed a good electrocatalytic response toward the reduction of TCA and the catalytic mechanism was also discussed. The overpotential for the reduction of TCA was lowered by at least 0.8 V compared with that obtained at bare glassy carbon electrode. The linear range spans the concentration of TCA from 2.0×10^?6 to1.2×10^?5 M and the detection limit was 1.2×10^?7 M. In addition, the stability, repeatability and selectivity of the sensor were also evaluated.     

Selective Voltammetric Determination of Tartrazine in the Presence of Red 10B by Nanogold‐modified Carbon Paste Electrode

A nanogold modified carbon paste electrode (NG‐CPE) was fabricated and used as selective voltammetric sensor for determination of Tartrazine in the presence of Red 10B using cyclic voltammetry (CV), differential pulse voltammetry (DPV), and chronoamperometry (CHA). Electrochemical parameters including the diffusion coefficient (D), the electron transfer coefficient (aXXXXX), and the electron transfer number (n) were determined for the oxidation of Tartrazine. This modified electrode can be applied to simultaneous determination of Tartrazine and Red 10B, because of considerable decreases of anodic overpotentials for both compounds. After optimizing the experimental conditions, the anodic peak current of Tartrazine was linear to its concentration in the range of 0.05‐1.5 μmol l^?1, and the detection limit was 0.017 μmol l^?1 in phosphate buffer solution (PBS) at pH 4.0. The modified electrode has good stability and repeatability. It was applied to the determination of Tartrazine and Red 10B in soft drinks with satisfactory results.     

Renewable Silver‐Amalgam Film Electrode for Rapid Square‐Wave Voltammetric Determination of Thiamethoxam Insecticide in Selected Samples

The paper presents the use of a renewable silver‐amalgam film electrode (Hg(Ag)FE) for the determination of the insecticide thiamethoxam (TMO) in Britton‐Robinson buffer pH 7.0 (LOD=0.25 µg mL^?1, LOQ=0.70 µg mL^?1) by direct cathodic square‐wave voltammetry (SWV). The voltammetric response for TMO obtained at this electrode was the same as that obtained with a hanging mercury drop electrode, represented by two distinct reduction peaks. Since the electron transfer processes are coupled with chemical reactions involving protons, the SWV signals strongly depend on the pH of the supporting electrolyte. The developed Hg(Ag)FE‐SWV method was tested for the determination of TMO in spiked honey and river water samples, as well as for the determination of its content in the commercial formulation Actara 25 WG.     

The Mn‐zeolite/Graphite Modified Glassy Carbon Electrode: Fabrication,Characterization and Analytical Applications

In this work, low‐cost and environmentally friendly natural zeolite exchanged with Mn²⁺ cations was used for the first time to modify the glassy carbon electrode with the aim to obtain a fast and simple sensor for voltammetric determination of paracetamol (PAR). The Mn‐zeolite/graphite modified glassy carbon electrode (MnZG?GCE) was prepared by evaporation of solvent from dispersion of the zeolite/graphite mixture with the polymer in acetone. The electrochemical characteristics of MnZG?GCE were conducted by electrochemical impedance spectroscopy and cyclic voltammetry. Compared with graphite modified GCE (G?GCE), MnZG?GCE exhibited better electrochemical parameters, which confirms the superiority of applying zeolite in the proposed sensor. The optimization of the pH‐value of supporting electrolyte and instrumental parameters were carried out. The peak current was proportional to the concentration of PAR in a phosphate buffer saline of pH 6.0 in the range from 0.029 to 0.69 mg L^?1 (R=0.9997) with limit of detection of 8.8 μg L^?1. Finally, the proposed electrode was successfully applied to determine the paracetamol in pharmaceutical formulation and certified reference materials. The satisfactory recoveries, which ranged from 89.2 to 102.7 %, were obtained for all studied samples. It confirmed the attractiveness of relatively inexpensive, easy to fabricate and non‐toxic MnZG?GCE in determination of PAR in complicated matrixes.