Optimization of parameters of sampling and determination of reduced sulfur compounds using cryogenic capture and gas chromatography in tropical urban atmosphere

Reduced sulfur compounds, RSCs (H₂S, COS, CH₃SH, CH₃SCH₃, CS₂ and CH₃S₂CH₃) play a role in global cycle and acid rain formation. At trace levels RSCs in air are difficult to collect, store and analyze because of their highly adsorptive and reactive properties. This work optimizes parameters of sampling and instrumental determination of RSCs for urban measurements. The method used is based on cryogenic sampling and gas chromatography provided with a cryofocusing trap and flame photometric detection.Greater sampling efficiency was obtained with liquid argon as freezing fluid and air flow rate of 150 mL min^? 1 for two hours. Best results have been obtained with preconcentration for 3 min and injection volume of 3 ml. For H₂S, CH₃SH and CH₃S₂CH₃ the method showed a precision of 89%, limit of detection of 0.10 µg m^? 3 and limit of quantification 0.3 µg m^? 3. For CH₃SCH₃ and CS₂ the corresponding values were 89%, 0.15 µg m^? 3 and 0.5 µg m^? 3 and for COS were 75%, 0.18 µg m^? 3 and 0.8 µg m^? 3 respectively. Sampling efficiency varied between 70–80% for all the RSCs. Accuracy of H₂S from field measurements obtained with parallel measurements using a continuous monitor varied between 88 and 98%. The optimized methodology proved to be suitable for field measurements in urban tropical atmospheres with different characteristics.     

Matrix solid‐phase dispersion with chitosan‐zinc oxide nanoparticles combined with flotation‐assisted dispersive liquid–liquid microextraction for the determination of 13 n‐alkanes in soil samples

In this study, chitosan‐zinc oxide nanoparticles were used as a sorbent of miniaturized matrix solid‐phase dispersion combined with flotation‐assisted dispersive liquid–liquid microextraction for the simultaneous determination of 13 n‐alkanes such as C₈H₁₈ and C₂₀H₄₂ in soil samples. The solid samples were directly blended with the chitosan nanoparticles in the solid‐phase dispersion method. The eluent of solid‐phase dispersion was applied as the dispersive solvent for the following flotation‐assisted dispersive liquid–liquid microextraction for further purification and enrichment of the target compounds prior to gas chromatography with flame ionization detection. Under the optimum conditions, good linearity with correlation coefficients in the range 0.9991 < r² < 0.9995 and low detection limits between 0.08 to 2.5 ng/g were achieved. The presented procedure combined the advantages of chitosan‐zinc oxide nanoparticles, solid‐phase dispersion and flotation‐assisted dispersive liquid–liquid microextraction, and could be applied for the determination of n‐alkanes in complicated soil samples with acceptable recoveries.     

Monophosphine‐substituted diiron azadithiolate complexes: New syntheses,characterization and electrochemical properties

Investigating the synthesis and properties of diiron azadithiolate complexes is one of the key topics for mimicking the active site of [FeFe]‐hydrogenases, which might be very useful for the design of new efficient catalysts for hydrogen production and the development of a future hydrogen economy. A series of new phosphine‐substituted diiron azadithiolate complexes as models for the active site of [FeFe]‐hydrogenases are described. A novel and efficient way was firstly established for the preparation of phosphine‐substituted diiron azadithiolate complexes. The reaction of Fe₂(μ‐SH)₂(CO)₆ and phosphine ligands L affords the intermediate Fe₂(μ‐SH)₂(CO)₅L ( A ). The intermediate reacts in situ with a premixed solution of paraformaldehyde and ammonium carbonate to produce the target phosphine‐substituted diiron azadithiolate complexes Fe₂[(μ‐SCH₂)₂NH](CO)₅L ( 1a – 1f ) (L = P(C₆H₄–4‐CH₃)₃, P(C₆H₄–3‐CH₃)₃, P(C₆H₄–4‐F)₃, P(C₆H₄–3‐F)₃, P(2‐C₄H₃O)₃, PPh₂(OCH₂CH₃)). Furthermore, reactions of the intermediate A with I‐4‐C₆H₄N(CH₂Cl)₂ in the presence of Et₃N give the phosphine‐substituted diiron azadithiolate complexes Fe₂[(μ‐SCH₂)₂NC₆H₄–4‐I](CO)₅L ( 2a – 2e ) (L = P(C₆H₄–4‐CH₃)₃, P(C₆H₄–3‐CH₃)₃, P(C₆H₄–4‐F)₃, P(C₆H₄–3‐F)₃, P(2‐C₄H₃O)₃). All the complexes were fully characterized using elemental analysis, IR and NMR spectroscopies and, particularly for 1a , 1c – 1e , 2a and 2c , single‐crystal X‐ray diffraction analysis. In addition, complexes 1a – 1f and 2a – 2e were found to be catalysts for H₂ production under electrochemical conditions. Density functional theory calculations were performed for the reactions of Fe₂(μ‐SH)₂(CO)₆ + P(C₆H₄–4‐CH₃)₃.     

Preparation of hydrophilic molecularly imprinted solid‐phase microextraction fiber for the selective removal and extraction of trace tetracyclines residues in animal derived foods

The present work reported a novel hydrophilic and selective solid‐phase microextraction fiber by improved multiple co‐polymerization method immobilization of tetracycline molecularly imprinted polymer on a stainless steel wire and directly coupled with high‐performance liquid chromatography for sensitive determination of trace tetracyclines residues in animal derived foods. The developed molecularly imprinted polymer coated solid‐phase microextraction fibers were characterized through scanning electron microscopy, Fourier transfer infrared spectroscopy, thermogravimetric analysis, and adsorption experiments, the fiber with cross‐linked and porous structure was observed and high thermal and chemical stability. The maximum adsorption capacity of this fiber with good selectivity reached 2.35 µg/mg in aqueous matrices, and showed good repeatability (relative standard deviation ≤ 6.6%, n = 5) and satisfying reproducibility between fiber to fiber (relative standard deviation ≤ 7.8%, n = 5). Under the optimized solid‐phase microextraction conditions, satisfactory linearity (5–1000 µg/L) and detection limits (0.38–0.72 µg/kg, S/N = 3) for all the tetracyclines were obtained. The practicality of this method was proved by adding tetracycline, oxytetracycline at three levels to milk, chicken, and fish samples with good recoveries of 77.3–104.4%.     

Addition of sulfur radicals to fullerenes

The addition of oxygen‐centered radicals to fullerenes has been intensively studied due to their role in cell protection against against hydrogen peroxide induced oxidative damage. However, the analogous reaction of sulfur‐centered radicals has been largely overlooked. Herein, we investigate the addition of S‐centered radicals to C₅₀, C₆₀, C₇₀, and C₁₀₀ fullerenes by means of DFT calculations. The radicals assayed were: S, SH, SCH₃, SCH₂CH₃, SC₆H₅, SCH₂C₆H₅, and the open‐disulfide SCH₂CH₂CH₂CH₂S. Sulfur, the most reactive species, prefers to be attached to a 66‐bond of C₆₀ with a binding energy (E_bind) of 2.4 eV. For the SR radicals the electronic binding energies to C₆₀ are 0.77, 0.74, 0.58, 0.67, and 0.35 eV for SH, SCH₃, SCH₂CH₃, SCH₂C₆H₅, and SC₆H₅, respectively. The reactivity of C₆₀ toward SR radicals can be increased by lithium doping. For Li@C₆₀, the E_bind is increased by 0.65 eV with respect to C₆₀, but only by 0.33 eV for the exohedral doping. Fullerenes act like free radical sponges. Indeed, the C₆₀‐SR E_bind can be duplicated if two radicals are added in ortho or para positions. The enhanced reactivity because of multiple additions is mostly a local effect, although the addition of one radical makes the whole cage more reactive. Therefore, as observed for hydroxylated fullerenes, they should protect cells from oxidative damage. However, the thiolated fullerenes have one advantage, they can be easily attached to gold nanoparticles. For the addition on pentagon junctions smaller fullerenes like C₅₀ are more reactive than C₆₀. Interestingly, C₇₀ is as reactive as C₆₀, even for the addition on the equatorial belt. For larger fullerenes like C₁₀₀, reactivity decreases for the carbon atoms belonging to hexagon junctions. © 2010 Wiley Periodicals, Inc. Int J Quantum Chem, 2010     

Mixed bis(morpholine‐4‐dithiocarbamato‐S,S′)antimony(III) complexes: synthesis,characterization and biological studies

Some mixed bis(morpholine‐4‐dithiocarbamato‐S,S′)antimony(III) complexes [(OC₄H₈NCS₂)₂SbL] with oxygen or sulfur donor ligands [L = ―OOCCH₃ ( 1 ), ―OOCC₆H₅ ( 2 ), ―SOCCH₃ ( 3 ), ―SCH₂COOH ( 4 ), ―OOCC₆H₄(OH) ( 5 ), ―SCH₂CH₂CH₃ ( 6 ), ―OC₆H₅ ( 7 ), ½ ―SCH₂CH₂S― ( 8 )] have been synthesized by reacting the chloro‐bis(morpholine‐4‐dithiocarbamato‐S,S′)antimony(III) with corresponding oxygen or sulfur donor ligands in 1:1 or 2:1 stoichiometries. These have been characterized by melting point, molecular weight determination (cryoscopically), antimony (iodometrically) and sulfur (gravimetrically) estimation, elemental analyses (C, H and N), UV–visible, FT‐IR, far IR, multinuclear NMR (¹H and ¹³C)], TG/DTA analysis, ESI–mass and powder X‐ray diffraction studies. The splitting of the strong band observed at 1046–1066 cm^?1 due to υ(C―S) indicated anisobidentate mode of binding of the dithiocarbamate group, which was further supported by a ¹³C NMR signal appearing at around δ 200 due to NCS₂ moiety. The base peak observed at m/z 444.9 supports the strong chelating nature of the morpholine‐4‐dithiocarbamate compared to the other hetero ligands used. TGA revealed that, complexes 21 and 4 were decomposed in three steps; also 6 was decomposed in two steps, followed by the formation of Sb₂S₃. The results obtained by antimicrobial screening tests indicate that complex 3 showed a maximum zone of inhibition (20 mm) against Trichoderma ressie at a concentration of 200 µg ml^?1. Complexes 2 , 3 and 8 are most active (zone of inhibition (ZI) 17–20 mm) against both of the fungal species Aspergillus niger and Trichoderma ressie as well as complex 4 (ZI 17 mm) and 6 (ZI 18 mm) against Trichoderma ressie. Copyright © 2014 John Wiley & Sons, Ltd.     

Using magnetic core‐shell nanoparticles coated with an ionic liquid dispersion assisted by effervescence powder for the micro‐solid‐phase extraction of four beta blockers from human plasma by ultra high performance liquid chromatography with mass spectrometry detection

In this work, a novel, efficient, and green sorbent, SiO₂@Fe₃O₄ has been created and functionalized with 1‐butyl‐3‐methylimidazolium hexafluorophosphate as an ionic liquid. This sorbent was applied for microextraction of four beta blockers, propranolol, metoprolol, atenolol, and alprenolol with bupivacaine as internal standard from human plasma followed by liquid chromatography with mass spectrometric detection. A mixture of sodium bicarbonate and sodium dihydrogen phosphate was used as an extractant dispersive agent (effervescent power) to enhance the interaction between the magnetic sorbent and analytes. Main affecting parameters on microextraction and elution were optimized. Figures of merit for dispersive solid phase extraction with ionic liquid coated magnetic nanoparticles assisted by effervescent powder were calculated under the optimized conditions. The detection limits for propranolol, metoprolol, atenolol, and alprenolol were found at 0.33, 0.62, 0.03, and 0.44 ng/mL, respectively. For all analytes, good linearity was obtained. Intra‐ (n = 5) and interday (n = 10) precision were both under 6.3% while the preconcentration factors were obtained in the range between 15–18. The extraction efficiencies for each analyte ranged from 75 to 91%. The method was successfully applied for determination of trace amounts of the beta blockers in human plasma samples.     

Contributions of Various Noncovalent Bonds to the Interaction between an Amide and S‐Containing Molecules

N‐Methylacetamide, a model of the peptide unit in proteins, is allowed to interact with CH₃SH, CH₃SCH₃, and CH₃SSCH₃ as models of S‐containing amino acid residues. All of the minima are located on the ab initio potential energy surface of each heterodimer. Analysis of the forces holding each complex together identifies a variety of different attractive forces, including SH???O, NH???S, CH???O, CH???S, SH???π, and CH???π H‐bonds. Other contributing noncovalent bonds involve charge transfer into σ* and π* antibonds. Whereas some of the H‐bonds are strong enough that they represent the sole attractive force in several dimers, albeit not usually in the global minimum, charge‐transfer‐type noncovalent bonds play only a supporting role. The majority of dimers are bound by a collection of several of these attractive interactions. The SH???O and NH???S H‐bonds are of comparable strength, followed by CH???O and CH???S.     

H2S‐Mediated Thermal and Photochemical Methane Activation

Sustainable, low‐temperature methods for natural gas activation are critical in addressing current and foreseeable energy and hydrocarbon feedstock needs. Large portions of natural gas resources are still too expensive to process due to their high content of hydrogen sulfide gas (H₂S) mixed with methane, deemed altogether as sub‐quality or “sour” gas. We propose a unique method of activation to form a mixture of sulfur‐containing hydrocarbon intermediates, CH₃SH and CH₃SCH₃, and an energy carrier such as H₂. For this purpose, we investigated the H₂S‐mediated methane activation to form a reactive CH₃SH species by means of direct photolysis of sub‐quality natural gas. Photoexcitation of hydrogen sulfide in the CH₄+H₂S complex resulted in a barrierless relaxation by a conical intersection to form a ground‐state CH₃SH+H₂ complex. The resulting CH₃SH could further be coupled over acidic catalysts to form higher hydrocarbons, and the resulting H₂ used as a fuel. This process is very different from conventional thermal or radical‐based processes and can be driven photolytically at low temperatures, with enhanced control over the conditions currently used in industrial oxidative natural gas activation. Finally, the proposed process is CO₂ neutral, as opposed to the current industrial steam methane reforming (SMR).     

Solid-phase microextraction—Gas chromatography to determine volatile organic sulfur compounds in the air at sewage treatment plants

Solid-phase microextraction (SPME) was applied to the determination of 7 volatile organic sulfur compounds (VOSCs), which were analysed by gas chromatography-mass spectrometry. The compounds studied were ethyl mercaptan (CH₃CH₂SH), dimethyl sulfide ((CH₃)₂S), carbon disulfide (CS₂), propyl mercaptan (C₃H₈S), butyl mercaptan (C₄H₁₀S), dimethyl disulfide ((CH₃)₂S₂) and 1-pentanethiol (C₅H₁₂S). Temperature and time conditions of SPME extraction were optimised and the method was validated, with good linearity in a calibration range between 0.1 and 1000 μg m⁻³. Method detection limits ranged between 0.01 and 0.08 μg m⁻³ and method quantification limits were between 0.10 and 0.25 μg m⁻³, allowing real samples taken from several different areas of a sewage treatment plant to be analysed. Repeatability of the method between samples went from 5.6% for pentanethiol up to 14.2% for carbon disulfide, and concentrations of total target compounds were found between 18 and 529 μg m⁻³, depending on the sampling site.     

A new procedure for determination of nickel in some fake jewelry and cosmetics samples after dispersive liquid–liquid microextraction by FAAS

A new, simple and cheap dispersive liquid–liquid microextraction (DLLME) procedure was optimized for the preconcentration of trace amounts of Ni(II) as a prior step to its determination by flame atomic absorption spectrometry (FAAS). It is based on the microextraction of nickel, where appropriate amounts of the extraction solvent (CHCl₃), disperser solvent (ethanol) and chelating agent, name 5‐[(Z)‐isoxazol‐3‐yl‐diazenyl]‐2‐methyl‐quinolin‐8‐ol (MMD), were firstly synthesized/characterized and used. Various parameters that affect the extraction procedure such as pH, centrifugation rate and time, the chelating agent (MMD) concentration and sampling volume on the recovery of Ni(II) were investigated. The preconcentration of a 20 ml sample solution was thus enhanced by a factor of 80. The resulting calibration graph was linear in the range of 0.24–10 mg L⁻¹ with a correlation coefficient of 0.9998. The limit of detection (3 s/b) obtained under optimal conditions was 1.00 μg L⁻¹. The relative standard deviation for certified reference material determinations was 1.2%. The accuracy of the method was verified by the determination of Ni(II) in the certified reference material of wastewater (Waste water CWW TMD). The proposed procedure was successfully applied to the determination of Ni(II) in some fake jewelry and cosmetics samples.     

Reaction kinetics and thermochemistry of the chemically activated and stabilized primary ethyl radical of methyl ethyl sulfide,CH3SCH2CH2•, with O2 to CH3SCH2CH2OO•

Oxidation of methyl ethyl sulfide (CH₃SCH₂CH₃, methylthioethane, MES) under atmospheric and combustion conditions is initiated by hydroxyl radicals, MES radicals, generated after loss of a H atom via OH abstraction, will further react with O₂ to form chemically activated and stabilized peroxyl radical adducts. The kinetics of the chemically activated reaction between the CH₃SCH₂CH₂• radical and molecular oxygen are analyzed using quantum Rice-Ramsperger-Kassel theory for k(E) with master equation analysis and a modified strong-collision approach to account for further reactions and collisional deactivation. Thermodynamic properties of reactants, products, and transition states are determined by the B3LYP/6-31+G(2d,p), M062X/6-311+G(2d,p), ωB97XD/6-311+G(2d,p) density functional theory, and CBS-QB3, G3MP2B3, and G4 composite methods. The reaction of CH₃SCH₂CH₂• with O₂ forms an energized peroxy adduct CH₃SCH₂CH₂OO• with a calculated well depth of 34.1 kcal mol⁻¹ at the CBS-QB3 level of theory. Thermochemical properties of reactants, transition states, and products obtained under CBS-QB3 level are used for calculation of kinetic parameters. Reaction enthalpies are compared between the methods. The temperature and pressure-dependent rate coefficients for both the chemically activated reactions of the energized adduct and the thermally activated reactions of the stabilized adducts are presented. Stabilization and isomerization of the CH₃SCH₂CH₂OO• adduct are important under high pressure and low temperature. At higher temperatures and atmospheric pressure, the chemically activated peroxy adduct reacts to new products before stabilization. Addition of the peroxyl oxygen radical to the sulfur atom followed by sulfur-oxygen double bond formation and elimination of the methyl radical to form S(= O)CCO• + CH₃ (branching) is a potentially important new pathway for other alkyl-sulfide peroxy radical systems under thermal or combustion conditions.     

Kinetics of the reactions of the IO radical with dimethyl sulfide,methanethiol, ethylene,and propylene

The reactions of IO radicals with CH₃SCH₃, CH₃SH, C₂H₄, and C₃H₆ have been studied using the discharge flow method with direct detection of IO radicals by mass spectrometry. The absolute rate constants obtained at 298 K are the following: IO + CH₃SCH₃ → products (1): k₁ = (1.5 ± 0.2) × 10^?14; IO + CH₃SH → products (2): k₂ = (6.6 ± 1.3) × 10^?16; IO + C₂H₄ →products (3): k₃ < 2 × 10^?16; IO + C₃H₆ → products (4): k₄ < 2 × 10^?16 (units are cm³ molecule^?1 s^?1). CH₃S(O)CH₃ and HOI were found as products of reactions (1) and (2), respectively. The present lower value of k₁ compared to our previous determination is discussed.     

An in‐needle solid‐phase microextraction device packed with etched steel wires for polycyclic aromatic hydrocarbons enrichment in water samples

A novel, low‐cost and effective in‐needle solid‐phase microextraction device was developed for the enrichment of trace polycyclic aromatic hydrocarbons in water samples. The in‐needle solid‐phase microextraction device could be easily assembled by inserting hydrofluoric acid‐etched wires, which were used as adsorbent, into a 22‐gauge needle tube within spring supporters. Compared with the commercial solid‐phase microextraction fiber, the developed device has higher efficiency for the extraction of polycyclic aromatic hydrocarbons with four to six rings from water samples using the optimized extraction conditions. With gas chromatography equipped with a flame ionization detector, the limits of detection for the polycyclic aromatic hydrocarbons with four to six rings ranged from 0.0020 to 0.0067 ng/mL. The relative standard deviations for one needle and needle‐to‐needle extractions were in the range of 5.2–9.9% (n = 5) and 3.4–12.3% (n = 5), respectively. The spiked recoveries of the polycyclic aromatic hydrocarbons in tap water samples ranged from 73.2 to 95.4%. This in‐needle solid‐phase microextraction device could be a good field sampler because of the low sample loss over a long storage time.     

Organic mass spectrometry—X. Electron impact fragmentations of alkylthio group in 2-alkylthio-5-aminothiazolo[5,4-d] pyrimidines

In order to discuss hydrogen transfer in the skeletal fragmentation of thioethers on electron impact, mass spectra of a series of 2-n-alkylthio-5-aminothiazolo [5,4-d]pyrimidines have been determined. To aid the interpretation of the hydrogen migration, deuterium-labeled compounds which are substituted with deuterium in each position of 2-n-butylthio-5-aminothiazolo-pyrimidines were studied. By correlation of the spectra obtained from such labeled compounds, the initial hydrogen migration in the fragmentation to produce [M ? SH], [MS ? CH₃] and m/e 184 ions is concluded to be as follows: migration of the α-hydrogen atom to the sulfur induces formation of the [M ? SH] ion; migration of the β-hydrogen atom to the sulfur or nitrogen atom by a McLafferty rearrangement induces formation of the m/e 184 ion; and migration of γ-hydrogen atom to the sulfur induces formation of the [M ? SCH₃] ion.     

Solubility of dimethyldisulfide (DMDS) in aqueous solutions of Fe(III) complexes of trans-1,2-cyclohexanediaminetetraacetic acid (CDTA) using the static headspace method

Total reduced sulfurs quartet (H₂S, CH₃SH, CH₃SCH₃ and CH₃S₂CH₃) is part of a well-known environmental problem afflicting pulp mills exploiting the Kraft mill sulfate-pulp process. Utilization of ferric chelate complex of trans-1,2-cyclohexanediaminetetraacetic acid (CDTA) for the oxidative scrubbing of H₂S and CH₃SH in Kraft mill streams is beneficial from the standpoints of iron protection against precipitation and oxygen-mediated regenerative oxidation of the ferrous chelate CDTA. The remaining two sulfur-bearing compounds, considered not oxidizable by CDTA–Fe(III), undergo only physical absorption in such solutions, so their solubility in aqueous CDTA–Fe(III) alkaline solutions is a crucial parameter for designing the complete scrubbing-absorption process. This investigation was carried out to determine the Henry's law constants of dimethyldisulfide (DMDS) in pure water, in aqueous iron-free CDTA solutions and CDTA–Fe(III) complex solutions using the static headspace method with an estimated accuracy of 2%. Experiments with aqueous solutions of chelate concentrations varying between 38 and 300 mol m⁻³ were carried out at temperatures between 298 and 333 K and atmospheric pressure. It was shown that DMDS solubility decreases with increasing temperature for all systems and is not much influenced by the CDTA concentration and solution pH.     

Electronic structure of thiazides studied by 35Cl‐NQR spectroscopy and DFT calculations

NQR frequencies were determined for the ³⁵Cl isotope in a few benzodithiazine derivatives, chlorothiazide (CTZ), hydrochlorothiazide (HCTZ), althiazide (ATZ), trichloromethiazide (TCTZ), benzthiazide (BTZ) and furosemide (FSE), at liquid nitrogen and room temperatures. It was found that changes of the substituent at C‐3 are transferred through a system of coupled rings on to the chlorine atom at C‐6. The substituents occurring in thiazides can be ordered according to increasing electron‐acceptor properties as —CH₂SCH₂Ph < —CH₂SCH₂CH?CH₂ <—CHCl₂. At the liquid nitrogen temperature —CH₂SCH₂Ph and —CH₂SCH₂CH?CH₂ are electron donors, and CHCl₂ is an electron acceptor, whereas at room temperature —CH₂SCH₂Ph is an electron donor and —CH₂SCH₂CH?CH₂ and —CHCl₂ are electron acceptors. The character of the substituent properties is preserved irrespective of whether the system is aromatic or aliphatic. The NQR frequencies and substituents properties are well reproduced by the DFT B3LYP/6–311+G(2d,p) method. The topological properties of the Laplacian of the electron density were analysed within the AIM (atoms in molecules) approach. The changes in the electron density at C‐3 are correlated with the biological activity of the compounds studied. Copyright © 2003 John Wiley & Sons, Ltd.     

Difference in Conversions Between Dimethyl Sulfide and Methanethiol in a Cold Plasma Environment

This study compared the conversion of two malodorous substances, dimethyl sulfide (CH₃SCH₃, DMS) and methanethiol (CH₃SH) in a cold plasma reactor. The DMS and CH₃SH were successfully destroyed at room temperature. DMS decomposed less than CH₃SH at the same conditions. In oxygen-free condition, CS₂ and hydrocarbons were the major products, while SO₂ and CO_x were main compounds in oxygen-rich environments. The DMS/Ar plasma yielded more hydrocarbons and less CS₂ than that of CH₃SH/Ar plasma. In the CH₃SH/O₂/Ar plasma, rapid formation of SO and CO resulted in the yields much more amounts of SO₂ and CO₂ than those in the DMS/O₂/Ar plasma; and remained only a trace of total hydrocarbons, CH₂O, CH₃OH, CS₂, and OCS. The major differences between the reaction mechanisms of DMS and CH₃SH were also proposed and discussed.     

Simple and rapid determination of phthalates using microextraction by packed sorbent and gas chromatography with mass spectrometry quantification in cold drink and cosmetic samples

A simple and rapid method using microextraction by packed sorbent coupled with gas chromatography and mass spectrometry has been developed for the analysis of five phthalates, namely, diethyl phthalate, benzyl‐n‐butyl phthalate, dicyclohexyl phthalate, di‐n‐butyl phthalate, and di‐n‐propyl phthalate, in cold drink and cosmetic samples. The various parameters that influence the microextraction by packed sorbent performance such as extraction cycle (extract–discard), type and amount of solvent, washing solvent, and pH have been studied. The optimal conditions of microextraction using C₁₈ as the packed sorbent were 15 extraction cycles with water as washing solvent and 3 × 10 μL of ethyl acetate as the eluting solvent. Chromatographic separation was also optimized for injection temperature, flow rate, ion source, interface temperature, column temperature gradient and mass spectrometry was evaluated using the scan and selected ion monitoring data acquisition mode. Satisfactory results were obtained in terms of linearity with R² >0.9992 within the established concentration range. The limit of detection was 0.003–0.015 ng/mL, and the limit of quantification was 0.009–0.049 ng/mL. The recoveries were in the range of 92.35–98.90% for cold drink, 88.23–169.20% for perfume, and 88.90–184.40% for cream. Analysis by microextraction by packed sorbent promises to be a rapid method for the determination of these phthalates in cold drink and cosmetic samples, reducing the amount of sample, solvent, time and cost.     

Synthesis and Crystal Structure of Tellurium(II) bis(2‐methoxycarbonylethanethiolate): A Novel Coordination Mode of Tellurium

The tellurium(II) dithiolates Te[SCH₂CH₂C(O)OCH₃]₂, ( 1 ), Te[SCH₂CH₂CH₂SC(O)CH₃]₂, ( 2 ), and Te[SCH₂CH₂CH₂CH₂SC(O)CH₃]₂, ( 3 ) were synthesized from Te(S^tBu)₂ and the corresponding thiol. All compounds are sensitive toward higher temperatures and light and decompose to elemental tellurium and the disulfide. In the solid state, the Te atom of 1 exhibits the novel Te(S₂Te₂) coordination mode. Additionally to the two Te—S bonds, each Te atom forms two long Te···Te contacts to neighboring molecules, leading to a coordination number of four and a distorted sawhorse configuration. No intramolecular Te···O interactions are present in the solid state, in accordance with ab initio calculations (MP2/ecp‐basis) for the isolated molecule. ¹²⁵Te NMR shifts of all compounds lay within a narrow range and close to the respective shift of other Te(SCH₂R)₂ compounds. VT ¹²⁵Te NMR spectra gave no hint to donor acceptor interactions in solution for any of the compounds and thus corroborate results from IR‐spectroscopy, ab initio geometry optimizations, and thermochemical calculations.