Nanostructured Three‐Dimensional (3D) Assembly of 2D MoS2 and Graphene Directly Build From Acidic Graphite Oxide

A 3D highly interconnected macroporous network of reduced GO having finely dispersed few‐layered 2D MoS₂ nanosheets was constructed through direct use of acidic graphite oxide (GO) for the first time. This facile and technologically scalable process can afford efficient hydrodesulfurization electrocatalysts as potential anode materials at lower cost, and can circumvent the poor thermal stability and recyclability of the material. The strategy provided here can be the basis to design and develop practical processes to address the ultimate goal of large‐scale manufacturing of hybrids composed of 2D materials for various energy and catalysis applications.     

A Phytic Acid Induced Super‐Amphiphilic Multifunctional 3D Graphene‐Based Foam

Surfaces with super‐amphiphilicity have attracted tremendous interest for fundamental and applied research owing to their special affinity to both oil and water. It is generally believed that 3D graphenes are monoliths with strongly hydrophobic surfaces. Herein, we demonstrate the preparation of a 3D super‐amphiphilic (that is, highly hydrophilic and oleophilic) graphene‐based assembly in a single‐step using phytic acid acting as both a gelator and as a dopant. The product shows both hydrophilic and oleophilic intelligence, and this overcomes the drawbacks of presently known hydrophobic 3D graphene assemblies. It can absorb water and oils alike. The utility of the new material was demonstrated by designing a heterogeneous catalytic system through incorporation of a zeolite into its amphiphilic 3D scaffold. The resulting bulk network was shown to enable efficient epoxidation of alkenes without prior addition of a co‐solvent or stirring. This catalyst also can be recovered and re‐used, thereby providing a clean catalytic process with simplified work‐up.     

Graphene‐Assisted Room‐Temperature Synthesis of 2D Nanostructured Hybrid Electrode Materials: Dramatic Acceleration of the Formation Rate of 2D Metal Oxide Nanoplates Induced by Reduced Graphene Oxide Nanosheets

A new prompt room temperature synthetic route to 2D nanostructured metal oxide–graphene‐hybrid electrode materials can be developed by the application of colloidal reduced graphene oxide (RGO) nanosheets as an efficient reaction accelerator for the synthesis of δ‐MnO₂ 2D nanoplates. Whereas the synthesis of the 2D nanostructured δ‐MnO₂ at room temperature requires treating divalent manganese compounds with persulfate ions for at least 24 h, the addition of RGO nanosheet causes a dramatic shortening of synthesis time to 1 h, underscoring its effectiveness for the promotion of the formation of 2D nanostructured metal oxide. To the best of our knowledge, this is the first example of the accelerated synthesis of 2D nanostructured hybrid material induced by the RGO nanosheets. The observed acceleration of nanoplate formation upon the addition of RGO nanosheets is attributable to the enhancement of the oxidizing power of persulfate ions, the increase of the solubility of precursor MnCO₃, and the promoted crystal growth of δ‐MnO₂ 2D nanoplates. The resulting hybridization between RGO nanosheets and δ‐MnO₂ nanoplates is quite powerful not only in increasing the surface area of manganese oxide nanoplate but also in enhancing its electrochemical activity. Of prime importance is that the present δ‐MnO₂–RGO nanocomposites show much superior electrode performance over most of 2D nanostructured manganate systems including a similar porous assembly of RGO and layered MnO₂ nanosheets. This result underscores that the present RGO‐assisted solution‐based synthesis can provide a prompt and scalable method to produce nanostructured hybrid electrode materials.     

三维氮掺杂石墨烯对水中铅和镉的吸附

采用多巴胺(DA)作为还原剂和功能化试剂,进行了氧化石墨烯的功能化,制备了三维结构的氮掺杂石墨烯材料(rGO-DA)。与还原性氧化石墨烯(rGO)对比,rGO-DA具有更大的吸附容量。rGO-DA对Pb~(2+)和Cd~(2+)的吸附容量分别为91.4,43.5 mg/g。考察了吸附时间、pH值、初始浓度对Pb~(2+)和Cd~(2+)吸附效果的影响。结果表明,rGO-DA对Pb~(2+)和Cd~(2+)吸附达到平衡的时间为120 min,最佳pH值为5.0。在Pb~(2+)和Cd~(2+)初始浓度小于30μg/m L时,二者的吸附去除率分别为100%和87.7%。在吸附Pb~(2+),Cd~(2+)后,rGO-DA可轻松从水体中移除。用HCl脱附,循环使用3次后,rGO-DA对Pb~(2+)和Cd~(2+)的吸附容量无明显变化,可再生并重复使用。     

Zinc-Guided 3D Graphene for Thermally Chargeable Supercapacitors to Harvest Low-Grade Heat

Low-grade heat energy recycling is the key technology of waste-heat utilization, which needs to be improved. Here, we use a zinc-assisted solid-state pyrolysis route to prepare zinc-guided 3D graphene (ZnG), a 3D porous graphene with the interconnected structure. The obtained ZnG, with a high specific surface area of 1817 m²·g⁻¹ and abundant micropores and mesopores, gives a specific capacitance of 139 F·g⁻¹ in a neutral electrolyte when used as electrode material for supercapacitors. At a high current density of 8 A·g⁻¹, the capacitance retention is 93% after 10,000 cycles. When ZnG is used for thermally chargeable supercapacitors, the thermoelectric conversion of the low-grade heat energy is successfully realized. This work thus provides a demonstration for low-grade heat energy conversion.     

生物质羟基磷灰石作为模板制备三维石墨烯

As a new 2D material with excellent chemical stability, good electric conductivity, and high specific surface area, graphene has been widely used in energy storage and conversion devices. However, 2D graphene layers are easily stacked, which may significantly reduce the surface area and degrade the excellent electrical properties of graphene. To avoid this, one of the most effective methods is to construct 3D graphene (3DG) with specific porous microstructures. Chemical vapor deposition (CVD) is an important method for the synthesis of high-quality 3DG, where templates play a defining role in controlling the structure and cost of 3DG. Metallic materials with 3D microstructures, such as nickel foam, have proven to be useful as substrates for the growth of high-quality 3DG. However, metal substrates are usually expensive, and the pickling solution generated after etching may cause environmental problems. Therefore, non-metallic substrate materials with lower costs have been investigated for the preparation of 3DG. Herein, we developed a novel template material, mammal bone ashes, for the CVD preparation of 3DG. Mammal bone ash is an inexpensive and abundant biomass hydroxyapatite. During the high-temperature CVD reaction, the bone ash powders were slightly sintered to form a continuous porous structure with graphene coating. The morphology of 3DG is inherited from the microstructure of bone ash templates. After removing the bone ash template with hydrochloric acid, the template-grown 3DG was obtained with a unique bicontinuous structure, i.e. both the graphene framework and the void space were continuous. In addition, the pickling solution of the bone ash templates after etching was exactly the same as that for the raw materials for the production of phosphoric acid to achieve high atom utilization. We further optimized the graphitization degrees, layer number, and porous morphology of 3DGs. The microstructure evolution of 3DG is highly relevant to the layer thickness and uniformity of graphene layers. A short growth time would lead to a non-uniform and thin layer of graphene, which is not able to support a complex 3D porous structure. In contrast, a uniform graphene layer with proper thickness is capable of forming a robust 3D architecture. In addition, the facile CVD method can be extended to a series of metal phosphate templates, including tricalcium phosphate [Ca₃(PO₄)₂], trimagnesium phosphate [Mg₃(PO₄)₂], and aluminum phosphate [AlPO₄]. 3DG with bicontinuous morphology is promising as a conductive frame material in electrochemical energy storage devices. As an illustration, high-performance Li-S batteries were fabricated by the uniform composition of an S cathode on 3DG. In comparison with heavily stacked 2D graphene sheets in reduced graphene oxide / S composite, the non-flat structure of 3DGs remained unchanged even after the harsh melt-diffusion process of high-viscosity liquid sulfur. The resulting 3DG/S cathode delivered a high specific capacity of ~550 mAh∙g^-1 at a high current rate (2C). Our work opens an avenue to the low-cost and high-utility production of 3D graphene, which could be integrated with the well-developed phosphorus chemical industry.     

Boron‐Doped,Carbon‐Coated SnO2/Graphene Nanosheets for Enhanced Lithium Storage

Heteroatom doping is an effective method to adjust the electrochemical behavior of carbonaceous materials. In this work, boron‐doped, carbon‐coated SnO₂/graphene hybrids (BCTGs) were fabricated by hydrothermal carbonization of sucrose in the presence of SnO₂/graphene nanosheets and phenylboronic acid or boric acid as dopant source and subsequent thermal treatment. Owing to their unique 2D core–shell architecture and B‐doped carbon shells, BCTGs have enhanced conductivity and extra active sites for lithium storage. With phenylboronic acid as B source, the resulting hybrid shows outstanding electrochemical performance as the anode in lithium‐ion batteries with a highly stable capacity of 1165 mA h g^?1 at 0.1 A g^?1 after 360 cycles and an excellent rate capability of 600 mA h g^?1 at 3.2 A g^?1, and thus outperforms most of the previously reported SnO₂‐based anode materials.     

Three‐Dimensional Macroassembly of Sandwich‐Like,Hierarchical, Porous Carbon/Graphene Nanosheets towards Ultralight,Superhigh Surface Area,Multifunctional Aerogels

A new, ultralight, superhigh surface area, multifunctional aerogel, which is macroassembled from sandwich‐like, hierarchical, porous carbon/graphene nanosheets, is described. The multifunctional aerogel was characterized by means of XRD, SEM, TEM, Raman spectroscopy, and UV/Vis absorption spectroscopy. The multifunctional aerogel had an ultralow density of 8 mg cm^?3 and a superhigh surface area of 2650 m² g^?1. The multifunctional aerogel was thermal stability and compressible. Meanwhile, the multifunctional aerogel exhibited high capacity for the adsorption of oils and organic solvents, unexpectedly high hydrogen adsorption and good electrochemical performance.     

MoS2 Nanosheets Supported on 3D Graphene Aerogel as a Highly Efficient Catalyst for Hydrogen Evolution

The development of efficient catalysts for electrochemical hydrogen evolution is essential for energy conversion technologies. Molybdenum disulfide (MoS₂) has emerged as a promising electrocatalyst for hydrogen evolution reaction, and its performance greatly depends on its exposed edge sites and conductivity. Layered MoS₂ nanosheets supported on a 3D graphene aerogel network (GA‐MoS₂) exhibit significant catalytic activity in hydrogen evolution. The GA‐MoS₂ composite displays a unique 3D architecture with large active surface areas, leading to high catalytic performance with low overpotential, high current density, and good stability.     

Sensitivity Enhancement in Nickel Hydroxide/3D‐Graphene as Enzymeless Glucose Detection

A nickel hydroxide (Ni(OH)₂)/3D‐graphene composite is used as monolithic free‐standing electrode for enzymeless electrochemical detection of glucose. Ni(OH)₂ nanoflakes are synthesized by using a simple solution growth procedure on 3D‐graphene foam which was grown by chemical vapor deposition (CVD). The pore structure of 3D‐graphene allows easy access to glucose with high surface area, which leads to glucose detection with an ultrahigh sensitivity of 3.49 mA mM^?1 cm^?2 and a significant lower detection limit up to 24 nM. Cyclic voltammetry (CV) and potentionstatic mode is used for non‐enzymatic glucose sensing. The impedance and effective surface area have been studied well. The high sensitivity, low detection limit and simple configuration of Ni(OH)₂/three dimensional (3D)‐graphene composite electrodes can evoke its industrial application in glucose sensing devices.     

Ultrathin Hexagonal Hybrid Nanosheets Synthesized by Graphene Oxide‐Assisted Exfoliation of β‐Co(OH)2 Mesocrystals

In the present study, we report the synthesis of a high‐quality, single‐crystal hexagonal β‐Co(OH)₂ nanosheet, exhibiting a thickness down to ten atomic layers and an aspect ratio exceeding 900, by using graphene oxide (GO) as an exfoliant of β‐Co(OH)₂ nanoflowers. Unlike conventional approaches using ionic precursors in which morphological control is realized by structure‐directing molecules, the β‐Co(OH)₂ flower‐like superstructures were first grown by a nanoparticle‐mediated crystallization process, which results in large 3D superstructure consisting of ultrathin nanosheets interspaced by polydimethoxyaniline (PDMA). Thereafter, β‐Co(OH)₂ nanoflowers were chemically exfoliated by surface‐active GO under hydrothermal conditions into unilamellar single‐crystal nanosheets. In this reaction, GO acts as a two‐dimensional (2D) amphiphile to facilitate the exfoliation process through tailored interactions between organic and inorganic molecules. Meanwhile, the on‐site conjugation of GO and Co(OH)₂ promotes the thermodynamic stability of freestanding ultrathin nanosheets and restrains further growth through Oswald ripening. The unique 2D structure combined with functionalities of the hybrid ultrathin Co(OH)₂ nanosheets on rGO resulted in a remarkably enhanced lithium‐ion storage performance as anode materials, maintaining a reversible capacity of 860 mA h g^?1 for as many as 30 cycles. Since mesocrystals are ubiquitous and rich in morphological diversity, the strategy of the GO‐assisted exfoliation of mesocrystals developed here provides an opportunity for the synthesis of new functional nanostructures that could bear importance in clean renewable energy, catalysis, photoelectronics, and photonics.     

Recent Progress on Graphene‐based Electrochemical Biosensors

The detailed records and conclusions on the important advancements in graphene‐based electrochemical biosensors have been reviewed. Due to their outstanding properties, graphene‐based materials have been widely studied for the accurate electrochemical detection of many biomolecules, which is extremely vital to the development of biomedical instruments, clinical diagnosis, and disease treatment. This review discusses the graphene research for the effective immobilization of enzymes, including glucose oxidase, horseradish peroxidase, and hemoglobin, etc., and the accurate detection of biomolecules, including glucose, hydrogen peroxide, dopamine, ascorbic acid, uric acid, nicotinamide adenine dinucleotide, DNA, RNA, and carcinoembryonic antigen, etc. In most of the cases, the graphene‐based biosensors exhibited remarkable performance with high sensitivities, wide linear detection ranges, low detection limits, and long‐term stabilities.     

3D Starfish-Like FeOF on Graphene Sheets: Engineered Synthesis and Lithium Storage Performance

To address the problems associated with poor conductivity and large volume variation in practical applications as a conversion cathode, engineering of hierarchical nanostructured FeOF coupled with conductive decoration is highly desired, yet rarely reported. Herein, 3D starfish-like FeOF on reduced graphene oxide sheets (FeOF/rGO) is successfully prepared, for the first time, through a combination of solvothermal reaction, self-assembly, and thermal reduction. Integrating the structural features of the 3D hierarchical nanostructure, which favorably shorten the path for electron/ion transport and alleviate volumetric changes, with those of graphene wrapping, which can further enhance the electrical conductivity and maintain the structural stability of the electrode, the as-prepared FeOF/rGO composite exhibits a superior lithium-storage performance, including a high reversible capacity (424.5 mA h⁻¹ g⁻¹ at 50 mA g⁻¹), excellent stability (0.016 % capacity decay per cycle during 180 cycles), and remarkable rate capability (275.8 mA h⁻¹ g⁻¹ at 2000 mA g⁻¹).     

Hemin‐Functionalized Reduced Graphene Oxide Nanosheets Reveal Peroxynitrite Reduction and Isomerization Activity

Facile and efficient reduction of graphene oxide (GO) and novel applications of the reduced graphene oxide (RGO) based materials are of current interest. Herein, we report a novel and facile method for the reduction of GO by using a biocompatible reducing agent dithiothreitol (DTT). Stabilization of DTT by the formation of a six‐membered ring with internal disulfide linkage upon oxidation is responsible for the reduction of GO. The reduced graphene oxide is characterized by several spectroscopic and microscopic techniques. Dispersion of RGO in DMF remained stable for several weeks suggesting that the RGO obtained by DTT‐mediated reduction is hydrophobic in nature. This method can be considered for large scale production of good quality RGO. Treatment of RGO with hemin afforded a functional hemin‐reduced graphene oxide (H‐RGO) hybrid material that exhibited remarkable protective effects against the potentially harmful peroxynitrite (PN). A detailed inhibition study on PN‐mediated oxidation and nitration reactions indicate that the interaction between hemin and RGO results in a synergistic effect, which leads to an efficient reduction of PN to nitrate. The RGO also catalyzes the isomerization of PN to nitrate as the RGO layers facilitate the rapid recombination of ^.NO₂ with Fe^IV=O species. In the presence of reducing agents such as ascorbic acid, the Fe^IV=O species can be reduced to Fe^III, thus helping to maintain the PN reductase cycle.     

Kinetically Controlled Layer-by-Layer Stacking of Metal Oxide 2D Nanosheets

An efficient chemical way to finely control the layer-by-layer stacking of inorganic nanosheets (NS) is developed by tuning the type and composition of intercalant ion, and the reaction temperature for restacking process. The finely controlled stacking of NS relies on a kinetic control of the self-assembly of NS in the presence of coordinating organic cations. A critical role of organic cations in this assembly highlights the importance of the appropriate activation energy. Of prime importance is that a fine-control of the interstratification of 2D NS is highly effective not only in tailoring its pore structure but also in enhancing its electrode activity. The present study clearly demonstrates that the kinetically controlled restacking of NS provides a facile and powerful method to tailor their stacking number and functionality.     

A Versatile Platform of 2‐(3,4‐Dihydroxyphenyl) Pyrrolidine Grafted Graphene for Preparation of Various Graphene‐derived Materials

Covalent functionalization has proven an effective solution for graphene to realize its revolutionary potential in real applications, whereas the platform strategy (a reactive graphene‐based material acting as the platform to undergo post‐reactions for generation of various graphene‐derived materials) is an attractive option to execute efficiently such a task. This contribution demonstrates that 2‐(3,4‐dihydroxyphenyl) pyrrolidine (DHPP) grafted graphene, G‐OH, is a competent platform. Four typical but not exclusive graphene‐derived materials have been prepared from G‐OH by using the chemical virtue of each DHPP unit having three categories totaling six reactive sites. The controlled feature of 1,3‐dipolar cycloaddition for the synthesis of G‐OH ensures that the electronic structure and properties of pristine graphene are succeeded largely by G‐OH and thus its derivatives. A promising alternative to graphene oxide, which has been widely used as a platform to prepare the graphene‐derived materials but suffers from some intrinsic disadvantages, is thus developed.