An Amperometric Glucose Biosensor Based on Poly (Pyrrole‐2‐Carboxylic Acid)/Glucose Oxidase Biocomposite

A newly developed amperometric glucose biosensor based on graphite rod (GR) working electrode modified with biocomposite consisting of poly (pyrrole‐2‐carboxylic acid) (PCPy) particles and enzyme glucose oxidase (GOx) was investigated. The PCPy particles were synthesized by chemical oxidative polymerization technique using H₂O₂ as initiator of polymerization reaction and modified covalently with the GOx (PCPy‐GOx) after activation of carboxyl groups located on the particles surface with a mixture of N‐(3‐dimethylaminopropyl)‐N′‐ethylcarbodiimide hydrochloride (EDC) and N‐hydroxysuccinimide (NHS). Then the PCPy‐GOx biocomposite was dispersed in a buffer solution containing a certain amount of bovine serum albumin (BSA). The resulting biocomposite suspension was adsorbed the on GR electrode surface with subsequent solvent airing and chemical cross‐linking of the proteins with glutaraldehyde vapour (GR/PCPy‐GOx). It was determined that the current response of the GR/PCPy‐GOx electrodes to glucose measured at +300 mV vs Cl reference electrode was influenced by the duration of the PCPy particles synthesis, pH of the GOx solution used for the PCPy particles modification and the amount of immobilized PCPy‐GOx biocomposite. An optimal pH of buffer solution for operation of the biosensor was found to be 8.0. Detection limit was determined as 0.039 mmol L⁻¹ according signal to noise ratio (S/N: 3). The proposed glucose biosensor was tested in human serum samples.     

Determination of Selenium with a Poly(1,8‐diamino‐naphthalene)‐Modified Electrode

The performance of a poly(1,8‐diaminonaphthalene)‐modified electrode for the determination of the Se(IV) ion in an aqueous medium was investigated with anodic stripping voltammetry without the pretreating of the sample. The experimental parameters for the analysis of Se(IV) were optimized and the characteristics of this polymer‐modified electrode were investigated by using cyclic voltammetry. The Se(IV) ions were chemically deposited onto the surface of the pDAN‐Au electrode in an acidic medium. The detection limit employing the anodic stripping differential pulse voltammetry was 9.0×10^?9 M for Se(IV) with 4.4 % of RSD. Satisfactory result for the determination of Se(IV) was acquired employing a certified standard urine reference material, SRM's 2670 (trace element in urine) with 4.1 ppb of SD.     

Sol‐Gel‐Derived Biosensor Based on Plant Tissue: The Inhibitory Effect of Atrazine on Polyphenol Oxidase Activity for Determination of Atrazine

This work presents a sol‐gel based biosensor for atrazine determination which has been obtained by introducing the enzyme polyphenol oxidase from apple tissue in a sol‐gel matrix. Apple tissue acts as a molecular recognition element. Atrazine is an inactive compound electrochemically; redox coupling of dopamine was used for studying atrazine behavior. Atrazine was determined by monitoring the inhibition power of polyphenol oxidase activity. The measurements were performed in 0.1 M KH₂PO₄‐NaOH buffer (pH 7.5). The effect of various experimental parameters such as pH, concentration of buffer, concentration of dopamine, incubation time and matrix composition has been investigated for optimum analytical performance. The biosensor consisted of 10.3% (w/w) of apple tissue. The bioelectrode exhibits a linear response for dopamine and atrazine concentrations in the range of 5.66 × 10^?6?2.27 × 10^?3M and 1 × 10^?5 ?1 × 10^?4 M with a detection limit of 4.2 × 10^?6 and 5.5 × 10^?6 M, respectively. A correlation coefficient of 0.9945 and a relative standard deviation (R.S.D.) of 3.29% for dopamine, 0.9944 and 3.69% for a trazine were achieved.     

Graphene/Poly(vinylferrocene) Composite Based Amperometric Biosensor for L‐lysine Determination

A novel and sensitive amperometric biosensor for L‐lysine determination based on a glassy carbon electrode (GCE) modified with graphene (GR) and redox polymer poly(vinylferrocene) (PVF) was constructed. L‐lysine‐α‐oxidase was immobilized onto the modified GCE by a glutaraldehyde/bovine serum albumin cross‐linking procedure. SEM, CV and EIS were used for the characterization of the surface morphology and stepwise fabrication processes of PVF/GR composite. Optimal composition of the biosensor and experimental conditions that affect the performance of the biosensor are discussed. The effect of buffer pH on biosensor response was studied in detail over a wide pH range. L‐lysine biosensor displayed a linear range of 9.9×10⁻⁷ ‐ 3.1×10⁻⁴ M with a low detection limit of 2.3×10⁻⁷ M and K_M ^app value of 0.4 mM. The L‐lysine biosensor was tested using pharmaceutical sample and cheese with satisfactory results.     

Development of Biosensor for Catechol Using Electrosynthesized Poly(3‐methylthiophene) and Incorporation of LAC Simultaneously

Simultaneous electropolymerization of 3‐methylthiophene and incorporation of Laccase (LAC) was carried out in the presence of propylene carbonate as a medium by amperometric method. This enzyme modified electrode was used for the sensing of polyphenol. Catechol is taken as a model compound for the study. UV‐Vis spectral studies suggest no denaturation of LAC in presence of propylene carbonate. The SEM studies reveal the surface morphology and incorporation of LAC in P3MT with agglomerated flaky masses are observed in with and without enzyme micrographs. The cyclic voltammograms were recorded for 0.01 mM catechol on plain glassy carbon, polymer and enzyme incorporated electrodes at pH 6.0 and scan rate 50 mV s^?1. The fabricated electrochemical biosensor was used for the determination of catechol in aqueous solution by Differential Pulse Voltammetry (DPV) technique. The concentration linear range of 8×10^?8 to 1.4×10^?5 M a value of Michealis? Menten constant K_m=7.67 µmol dm^?3 and activation energy is 32.75 kJ mol^?1. It retains 83 % of the original activity after 60 days which is much higher than that of other biosensors. The developed biosensor was used to quantify catechol in the determination in real samples.     

Palladium Particles‐Impregnated Natural Phosphate Electrodes for Electrochemical Determination of Mercury in Ambient Water Samples

We present here a simple procedure for the determination of mercury(II) using differential pulse anodic stripping voltammetry (DPASV) at palladium particles‐impregnated natural phosphate modified carbon paste electrodes (Pd‐NP‐CPE). The surface of modified electrode was characterized using SEM, infrared spectroscopy, X‐ray diffraction and electrochemical analysis. All experimental variables involved in the voltammetric stripping method were optimized. The detection limit was found to be 4.99×10^?8 mol L^?1 (S/N=3) that is not different to the permitted value for Hg(II) in water reported by the Environmental Protection Agency (EPA). The proposed electrode exhibits good applicability for monitoring Hg(II) in tap and wastewater.     

AP-GOD Biosensor Based on a Modified Poly(PHENOL) Film Electrode and Its Application in the Determination of Low Levels of Phosphate

Abstract

The features of a biosensor based on a platinum electrode modified with a poly(phenol) film coupled with two enzymes, alkaline phosphatase(AP) and glucose oxidase(GOD), were studied. The modification of the surface of the working electrode decreases interference from ascorbic acid, uric acid and some oxidizable organic materials (e.g. glycine), and decreases the noise of the current. The concentration of substrate, the activity ratio of the two enzymes, the applied potential, and the assembling of biosensor are important for the determination of low levels of phosphate.

The two enzymes have been immobilized on an Immobilon^(R) membrane. The linearity range appears in two sections with different sensitivity: one from 8-110 μmol I^?1 and another one from 0.1-1.0 mmol I^?1, with 1.2 μA/mmol/cm² and 0.4 μA/mmol/cm², respectively. Except for some heavy metal ions, ascorbic acid and some oxidizable organic materials, common anions and cations don't interfere with the determination of phosphate.

The biosensor has been used to determine phosphate in some synthetic and real samples with a detection limit of 4 μmol I^?1 of phosphate. The results were compared with a standard spectrophotometric method. The accuracy and recovery of phosphate with the biosensor procedure are ±2% and 96 to 103%, respectively.

     

Simultaneous Electrochemical Detection of Co(II) and Cu(II) by 1‐Diazo‐2‐Naphthol‐4‐Sulfonic Acid/MWCNTs Modified Electrode

This work describes a simple preparation of 1‐diazo‐2‐naphthol‐4‐sulfonic acid (1,2,4‐acid) and multiwalled carbon nanotubes (MWCNTs) modified glassy carbon electrode (GCE) for the simultaneous detection of Co(II) and Cu(II). MWCNTs, with their good conductivity and large surface area, were drop‐casted onto the surface of the GCE prior to the electrodeposition of 1,2,4‐acid, a metal chelating agent. Co(II) and Cu(II) were simultaneously measured by differential pulse anodic stripping voltammetry (DPASV) in a batch system. Under optimum conditions, the linear range of Co(II) was between 0.10 and 2.5 μg mL⁻¹ with an LOD of 80 ng mL⁻¹. Two linear ranges were obtained for Cu(II), 0.0050 to 0.030 μg mL⁻¹ and 0.040 to 0.25 μg mL⁻¹,with an LOD of 2.4 ng mL⁻¹. The method offered a high operational stability for up to 52 measurements (RSD=3.4 % for Co(II) and 2.6 % for Cu(II)) and good reproducibility (RSD=1.2 % for Co(II) and 1.7 % for Cu(II)). In the simultaneous detection of Co(II) and Cu(II), there was no effect from common interferences found in wastewater. The method was successfully applied in real water samples with good recoveries (88.2±0.8 to 102.0±0.8 % for Co(II) and 96.5±0.4 to 103.8±0.9 % for Cu(II)) and the results were in good agreement with those obtained from inductively coupled plasma optical emission spectrometry (ICP‐OES) (P >0.05).     

Monodisperse Poly(lactide‐co‐glycolic acid)‐Based Nanocarriers for Gene Transfection

This contribution describes a simple, aerosol‐based method for fabricating monodisperse particles containing mixtures of poly(lactide‐co‐glycolic acid) [PLGA], protamine sulfate (Prot), and poly(l‐ lysine) [PLL] as nanocarriers for gene transfection. Aqueous solutions of PLGA, Prot, and PLL were collison‐atomized, and the resulting aerosolized droplets were dried “on the fly” to form solid particles, which then were electrostatically size‐classified into 50, 100, and 200 nm mobility diameter samples. Measurements of cell viability and transfection reveal that the fabricated nanocarriers have a lower cytotoxicity (>85% in cell viability) and a higher transfection efficiency [>8.7 × 10⁵ in relative light units (RLU) mg⁻¹] than does 25 kDa polyethyleneimine (≈50% and 6.8 × 10⁵ RLU mg⁻¹).     

Graphite Based Microsensors Developed for the Electrochemical Determination of L‐Tyrosine from Pharmaceutical Samples

Two electrochemical sensors were proposed for the determination of L‐tyrosine from pharmaceutical capsules. The electrochemical sensors were based on plain graphite paste and chitosan modified graphite paste. Working conditions, e. g. pH, supporting electrolytes have been optimized. The results revealed for both electrodes very low limits of quantification (LOQ) (0.18 mg L^?1 and 0.0018 mg L^?1) for plain graphite paste based sensors and for chitosan modified paste sensors respectively. A higher sensitivity of 7.95×10^?10 A mg L^?1 was obtained for the sensor based on plain graphite paste (G). The uniformity content test showed that L‐Tyrosine can be recovered in pharmaceutical capsules with an average value higher than 98.00 % and a relative standard deviation (RSD%) value less than 1.00 % (N=5).     

Hemoglobin‐Titanate Composite Based Biosensor for the Amperometric Determination of Hydrogen Peroxide in Acidic Medium

A hemoglobin‐titanate composite based biosensor was chosen for determination of H₂O₂ in an acidic medium. CV results of the Hb‐titanate modified pyrolytic graphite electrode showed a pair of well‐defined, quasi‐reversible redox peaks centered at ?246 mV (vs. Ag/AgCl) in a pH 5.0 HAc‐NaAc buffer solution. The modified electrode exhibited good electrocatalytic response for monitoring H₂O₂ and had a large linear detection range from 20 μM to 3.2 mM with a detection limit of 8 μM (S/N=3) and a sensitivity of 29.7 mA M^?1 cm^?2 in the pH 5.0 solution. The biosensor also possessed good long term storage stability.     

Determination of Some Heavy Metal Ions with a Carbon Paste Electrode Modified by Poly(glycidylmethacrylate‐methylmethacrylate‐divinylbenzene) Microspheres Functionalized by 2‐Aminothiazole

A carbon paste electrode modified with 2‐aminothiazole functionalized poly(glycidylmethacrylate‐methylmethacrylate‐divinylbenzene) microspheres was used for trace determination of mercury, copper and lead ions. After the open‐circuit accumulation of the heavy metal ions onto the electrode, the sensitive anodic stripping peaks were obtained by square wave anodic stripping voltammetry (SWASV)). Many parameters such as the composition of the paste, pH, preconcentration time, effective potential scan rate and stirring rate influence the response of the measurement. The procedures were optimized for most sensitive and reliable determinations of the desired species. For a 10‐min preconcentration time in synthetic solutions at optimum instrumental and experimental conditions, the detection limit (LOD) was 12.3, 2.8 and 4.5 μg L^?1 for mercury, copper and lead, respectively. The limits of detection may be enhanced by increasing the preconcentration time. For example, LOD of mercury and copper was 4.9 and 1.0 μg L^?1 for fifteen minutes preconcentration time. The sensitivity may also considered to be increased by using a more suitable electrode composition targeting the more conductive electrode with lesser amount of modified polymer for sub‐μg L^?1 levels of heavy metal ions. The optimized method was successfully applied to the determination of copper in tap water and waste water samples by means of standard addition procedure. The copper content found was comparable with the certified concentration of the waste water sample. The calibration plots for mercury and lead spiked real samples were also drawn.     

Metallophthalocyanine Based Carbon Paste Electrodes for the Determination of 2′,3′‐Dideoxyinosine

Novel electrochemical sensors based on carbon paste impregnated with metallopthalocyanine (MPc, M=Co, Fe) complexes, have been constructed for the assay of anti‐HIV drug 2′,3′‐dideoxyinosine (didanosine, DDI). Both modified electrodes showed electrocatalytic activity towards the oxidation of dideoxyinosine in phosphate buffer pH 7.4 with a working concentration range of 10^?6–10^?4 mol/L and a detection limit of 10^?7 mol/L magnitude order. The sensor proved to be highly reliable for the assay of the purity of DDI ‐ raw material as well as for the uniformity content test of Videx tablets.     

Amperometric Biosensor for Hydrogen Peroxide,Using Supramolecularly Immobilized Horseradish Peroxidase on the β‐Cyclodextrin‐Coated Gold Electrode

Horseradish peroxidase, previously modified with 1‐adamantane moieties, was supramolecularly immobilized on gold electrodes coated with perthiolated β‐cyclodextrin. The functionalized electrode was employed for the construction of an amperometric biosensor device for hydrogen peroxide using 1 mM hydroquinone as electrochemical mediator. The biosensor exhibited a fast amperometric response (6 s) and a good linear response toward H₂O₂ concentration between 12 μM and 450 μM. The biosensor showed a sensitivity of 1.02 mA/M cm², and a very low detection limit of 5 μM. The electrode retained 97% of its initial electrocatalytic activity after 30 days of storage at 4 ⁰C in 50 mM sodium phosphate buffer, pH 7.0.     

Electrochemical Activity Studies of Glucose Oxidase (GOx)‐Based and Pyranose Oxidase (POx)‐Based Electrodes in Mesoporous Carbon: Toward Biosensor and Biofuel Cell Applications

A simple study using a fixed amount of mesoporous carbon (MSU‐F‐C) was performed for the comparison of pyranose oxidase (POx) and glucose oxidase (GOx) in their electrochemical performance under biosensor and biofuel cell operating modes. Even though the ratio of POx to GOx in the glucose oxidation activity per unit weight of MSU‐F‐C was 0.35, the ratios of POx to GOx in sensitivity and power density were reversed to be 6.2 and 1.4, respectively. POx with broad substrate specificity and an option of large scale production using recombinant E. coli has a great potential for various electrochemical applications, including biofuel cells.     

The Synthesis and Characterizations of Calcium Phosphate Nanoparticles via β‐Cyclodextrin,Poly(oxyethylene)5 Nonyl Phenol Ether and Cyclohexane Medium

In this work, the calcium phosphate nanoparticles have been produced by new reverse micro emulsion method containing β‐cyclodextrin, poly(oxyethylene)₅ nonyl phenol ether and cyclohexane. Scanning electron microscope, transmission electron microscope, fourier transform infrared spectroscope and X‐ray diffraction were used to characterize the particles. The sizes of the nanoparticles were identified between 70‐80 nm. In conclusion, these results suggested that the developed reverse micro emulsion system based nanoparticles seem to be a promising formulation for calcium phosphate nanoparticles synthesis and it has immense potential in delivery of drugs and vaccines.     

Direct Determination of Paracetamol in Environmental Samples Using Screen‐printed Carbon/Carbon Nanofibers Sensor – Experimental and Theoretical Studies

The paper describes the first electrochemical method (differential pulse adsorptive stripping voltammetry, DPAdSV) using a screen‐printed sensor with a carbon/carbon nanofibers working electrode (SPCE/CNFs) for the direct determination of low (real) concentrations of paracetamol (PA) in environmental water samples. By applying this sensor together with DPAdSV, two linear PA concentration ranges from 2.0×10^?9 to 5.0×10^?8 mol L^?1 (r=0.9991) and 1.0×10^?7–2.0×10^?6 mol L^?1 ( r=0.9994) were obtained. For the accumulation time of 90 s, the limit of detection was 5.4×10^?10 mol L^?1. Moreover, the SPCE/CNFs sensor and the DPADSV procedure for PA determination are potentially applicable in field analysis. The process of PA adsorption at the SPCE/CNFs surface was investigated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and theoretical studies. In the theoretical study of the interaction of CNF and PA, the first species was modelled by graphene‐like clusters containing up to 37 rings. It was found that the preferable orientation of PA is parallel to the carbon surface with the binding energy of about ?68 kJ/mol calculated by symmetry‐adapted perturbation theory (SAPT). Both the selectivity and the accuracy of the developed sensor for real sample analysis were also investigated using Polish river and sea samples.     

Reagentless Biosensor for Hydrogen Peroxide Based on the Immobilization of Hemoglobin in Platinum Nanoparticles Enhanced Poly(chloromethyl thiirane) Cross‐linked Chitosan Hybrid Film

An unmediated hydrogen peroxide (H₂O₂) biosensor was prepared by co‐immobilizing hemoglobin (Hb) with platinum nanoparticles enhanced poly(chloromethyl thiirane) cross‐linked chitosan (CCCS‐PNs) hybrid film. CCCS could provide a biocompatible microenvironment for Hb and PNs could accelerate the electron transfer between Hb and the electrode. Spectroscopic analysis indicated that the immobilized Hb could maintain its native structure in the CCCS‐PNs hybrid film. Entrapped Hb exhibited direct electrochemistry for its heme Fe(III)/Fe(II) redox couples at ?0.396 V in the CCCS‐PNs hybrid film, as well as peroxidase‐like activity to the reduction of hydrogen peroxide without the aid of an electron mediator.     

Poly(N‐phenylmaleimide‐co‐acrylic acid)–copper(II) and poly(N‐phenylmaleimide‐co‐acrylic acid)–cobalt(II) complexes: Synthesis,characterization, and thermal behavior

The free‐radical copolymerization of N‐phenylmaleimide (N‐PhMI) with acrylic acid was studied in the range of 25–75 mol % in the feed. The interactions of these copolymers with Cu(II) and Co(II) ions were investigated as a function of the pH and copolymer composition by the use of the ultrafiltration technique. The maximum retention capacity of the copolymers for Co(II) and Cu(II) ions varied from 200 to 250 mg/g and from 210 to 300 mg/g, respectively. The copolymers and polymer–metal complexes of divalent transition‐metal ions were characterized by elemental analysis, Fourier transform infrared, ¹H NMR spectroscopy, and cyclic voltammetry. The thermal behavior was investigated with differential scanning calorimetry (DSC) and thermogravimetry (TG). The TG and DSC measurements showed an increase in the glass‐transition temperature (T_g) and the thermal stability with an increase in the N‐PhMI concentration in the copolymers. T_g of poly(N‐PhMI‐co‐AA) with copolymer composition 46.5:53.5 mol % was found at 251 °C, and it decreased when the complexes of Co(II) and Cu(II) at pHs 3–7 were formed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4933–4941, 2005