Modeling protein binding and elution over a chromatographic surface probed by surface plasmon resonance

Surface plasmon resonance (SPR) spectroscopy is used as a scaled-down, analytical, pseudo-chromatography tool for analyzing protein binding and elution over an ion-exchange surface under cyclic sorption conditions. A micrometric-scale adsorption surface was produced by immobilizing a typical ion exchange ligand – diethylaminoethyl (DEAE) – onto commercially available planar gold sensor chip surfaces pre-derivatized with a self-assembled monolayer of 11-mercaptoundecanoic acid with known density. An explicit mathematical formulation is provided for the deconvolution and interpretation of the SPR sensorgrams. An adsorption rate model is proposed to describe the SPR sensorgrams for bovine serum albumin, used here as model protein, when the DEAE surface is subjected to a cyclic series of binding and elution steps. Overall, we demonstrate that the adsorption rate model is capable of quantitatively describing BSA binding and elution for protein titers from dilute conditions up to overloaded conditions and a broad range of salt concentrations.     

螯合亲和色谱法分离转铁蛋白的4种分子形式

在ＴＳＫｇｅｌ－Ｃｈｅｌａｔｅ－５ＰＷ柱上用固定Ｃｕ２~（２＋）离子的螯合亲和色谱法（ＨＰ－ＩＭＡＣ）研究了Ｆｅ（Ⅲ）同去铁转铁蛋白的结合,讨论了所固定的几种金属离子对保留时间和柱寿命的影响;在生理ｐＨ条件下分离出了非饱和铁转铁蛋白的４种分子形式：ＦｅＮＴｆ,ＴｆＦｅｃ,ＦｅＮＴｆＦｅｃ（或Ｆｅ２Ｔｆ）和Ａｐｏ－Ｔｆ。     

Au nanoparticle-enhanced surface plasmon resonance sensing of biocatalytic transformations

N-(3-Aminopropyl)-N'-methyl-4,4'-bipyridinium is coupled to tiopronin-capped Au nanoparticles (diameter ca. 2 nm) to yield methyl(aminopropyl)viologen-functionalized Au nanoparticles (MPAV(2+)-Au nanoparticles). In situ electrochemical surface plasmon resonance (SPR) measurements are used to follow the electrochemical deposition of the bipyridinium radical cation modified Au nanoparticles on an Au-coated glass surface and the reoxidation and dissolution of the bipyridinium radical cation film. The MPAV(2+)-functionalized Au nanoparticles are also employed for the amplified SPR detection of NAD(+) and NADH cofactors. By SPR monitoring the partial biocatalyzed dissolution of the bipyridinium radical cation film in the presence of diaphorase (DP) NAD(+) is detected in the concentration range of 1x10(-4) M to 2x10(-3) M. Similarly, the diaphorase-mediated formation of the bipyridinium radical cation film on the Au-coated glass surface by the reduction of the MPAV(2+)-functionalized Au nanoparticles by NADH is used for the amplified SPR detection of NADH in the concentration range of 1x10(-4) M to 1x10(-3) M.     

Evaluation and optimization of the metal‐binding properties of a complex ligand for immobilized metal affinity chromatography

The simultaneous determination of two binding parameters for metal ions on an immobilized metal affinity chromatography column was performed by frontal chromatography. In this study, the binding parameters of Cu²⁺ to l ‐glutamic acid were measured, the metal ion‐binding characteristics of the complex ligand were evaluated. The linear correlation coefficients were all greater than 99%, and the relative standard deviations of two binding parameters were 0.58 and 0.059%, respectively. The experiments proved that the frontal chromatography method was accurate, reproducible, and could be used to determine the metal‐binding parameters of the affinity column. The effects of buffer pH, type, and concentration on binding parameters were explored by uniform design experiment. Regression, matching and residual analyses of the models were performed. Meanwhile, the optimum‐binding conditions of Cu²⁺ on the l ‐glutamic acid‐silica column were obtained. Under these binding conditions, observations and regression values of two parameters were similar, and the observation values were the best. The results demonstrated that high intensity metal affinity column could be effectively prepared by measuring and evaluating binding parameters using frontal chromatography combined with a uniform design experiment. The present work provided a new mode for evaluating and preparing immobilized metal affinity column with good metal‐binding behaviors.     

Inhibition binding studies of glycodendrimer/lectin interactions using surface plasmon resonance

Understanding protein/carbohydrate interactions is essential for elucidating biological pathways and cellular mechanisms but is often difficult due to the prevalence of multivalent interactions. Here, we evaluate the multivalent glycodendrimer framework as a means to describe the inhibition potency of multivalent mannose-functionalized dendrimers using surface plasmon resonance (SPR). Using highly robust, mannose-functionalized dithiol self-assembled monolayers on gold surfaces, we found that glycodendrimers were efficient inhibitors of protein/carbohydrate interactions. IC₅₀ values ranging from 260 nM to 13 nM were obtained for mannose-functionalized dendrimers with Concanavalin A.     

Facile synthesis of Ti4+‐immobilized affinity silica nanoparticles for the highly selective enrichment of intact phosphoproteins

Currently, great challenges to top‐down phosphoproteomics lie in the selective enrichment of intact phosphoproteins from complex biological samples. Herein, we developed a facile approach for synthesis of Ti⁴⁺‐immobilized affinity silica nanoparticles and applied them to the selective separation and enrichment of intact phosphoproteins based upon the principle of metal(IV) phosphate/phosphonate chemistry. The as‐prepared affinity materials exhibited high selectivity and adsorption capacities for model phosphoproteins (328.9 mg/g for β‐casein, 280.5 mg/g for ovalbumin, and 225.8 mg/g for α‐casein), compared with nonphosphoproteins (79.28 mg/g for horseradish peroxidase, 72.70 mg/g for BSA, and 27.28 mg/g for lysozyme). In addition, the resuability of the affinity silica nanoparticles was evaluated, and the results demonstrated a less than 10% loss of adsorption capacity after six adsorption–regeneration cycles. The practicability of the affinity materials was demonstrated by separating phosphoproteins from protein mixtures and drinking milk samples, and the satisfactory results indicated its potential in phosphoproteomics analysis.     

A unified view of propagating and localized surface plasmon resonance biosensors

The intense colors of noble metal nanoparticles have inspired artists and fascinated scientists for hundreds of years. In this review, we describe refractive index sensing platforms based on the tunability of the localized surface plasmon resonance (LSPR) of arrays of silver nanoparticles and of single nanoparticles. Specifically, the color associated with single nanoparticles and surface-confined nanoparticle arrays will be shown to be tunable and useful as platforms for chemical and biological sensing. Finally, the LSPR nanosensor will be compared to traditional, flat surface, propagating surface plasmon resonance sensors.     

Reversible immobilization of proteins with streptavidin affinity tags on a surface plasmon resonance biosensor chip

Dissociation of biotin from streptavidin is very difficult due to their high binding affinity. The re-use of streptavidin-modified surfaces is therefore almost impossible, making devices containing them (e.g. surface plasmon resonance (SPR) sensor chips) expensive. This paper describes a new protocol for reversible and site-directed immobilization of proteins with streptavidin affinity tags on the streptavidin-coated SPR biosensor chip (SA chip). Two streptavidin affinity tags, nano-tag and streptavidin-binding peptide (SBP tag), were applied. They both can specifically interact with streptavidin but have weaker binding force compared to the biotin–streptavidin system, thus allowing association and dissociation under controlled conditions. The SA chip surface could be regenerated repeatedly without loss of activity by injection of 50 mM NaOH solution. The fusion construct of a SBP tag and a single-chain antibody to mature bovine prion protein (scFv-Z186-SBP) interacts with the SA chip, resulting in a single-chain-antibody-modified surface. The chip showed kinetic response to the prion antigen with equilibrium dissociation constant K _D≈4.01×10⁻⁷. All results indicated that the capture activity of the SA chip has no irreversible loss after repeated immobilization and regeneration cycles. The method should be of great benefit to various biosensors, biochips and immunoassay applications based on the streptavidin capture surface.     

Preparation of Immobilized Metal Affinity Chromatographic Packings Based on Monodisperse Hydrophilic Non‐porous Beads and Their Application

Three hydrophilic immobilized metal affinity chromatographic packings for HPLC have been synthesized by chemical modification of 3.0 µm monodisperse non‐porous poly(glycidyl methacrylate‐co‐ethylenedimethacrylate) (P_GMA/EDMA) beads. The retention behavior of proteins on the metal ion chelated columns loaded with copper(II), nickel(II) and zin(II) ion was studied. The effect of pH on the protein retention was investigated on both the naked and metal ion chelated columns in the range from 4.0 to 9.0. Four proteins were quickly separated in 3.0 min with linear gradient elution at a flow rate of 3.0 mL/min by using the synthesized Ni²⁺‐IDA (iminodiacetic acid) packings. The separation time was shorter than other immobilized metal affinity chromatography reported in the literature. Purification of lysozyme from egg white and trypsin on the commercially available trypsin was performed on the naked‐IDA and Cu²⁺‐IDA columns, respectively. The purities of the purified trypsin and lysozyme were more than 92% and 95%, respectively.     

A micro-scale method employing surface plasmon resonance detection for the determination of conditions for immunoaffinity chromatography of proteins

Summary The BIAcore^TM Biosensor System utilizes a detection principle known as Surface Plasmon Resonance (SPR) which, in simple terms, detects changes in the refractive index of a solution in contact with a gold film. The gold film is surface modified with carboxymethylated dextran to produce a hydrophillic matrix onto which macromolecules may be covalently immobilized. In this respect, the BIAcore^TM is similar to any other insoluble matrix, such as a chromatographic support. The SPR detection principle, however, allows one to directly visualize the interaction under study, in real time and without the need for reporter molecules such as enzyme-labels. In addition, the very small sample requirements, automated robotics unit and ease of data analysis suggest the potential use of the BIAcore^TM instrumentation for assay development and possibly process development, especially where bio-specific interactions such as immunoaffinity chromatography are used as a step in the process. In this report, we demonstrate the use of the BIAcore^TM SPR detector for the micro-scale determination of conditions for immunoaffinity chromatography of soluble complementreceptor 1, sCR1.     

Dielectric properties of UV-irradiated ultrathin polysulfone films revealed by surface plasmon resonance method

The surface plasmon resonance research of manufactured highly homogeneous ultrathin polysulfone films was performed, which were exposed to the short-wave (254?nm) UV irradiation of various durations. Surprisingly, the resonance incident angle and dielectric constant increase after short-term UV irradiation before the ordinary decrease caused by usual polymer degradation. The experimental results are ascribed to the formation of polar groups leading to orientation of chain fragments of intermediate length followed by their breaking and formation of mobile short fragments under longer times of irradiation.     

Colloidal-based localized surface plasmon resonance (LSPR) biosensor for the quantitative determination of stanozolol

This work reports the systematic preparation of biosensors through the use of functionalized glass substrates, noble metal gold colloid, and measurement by localized surface plasmon resonance (LSPR). Glass substrate was modified through chemical silanization, and the density of gold colloid was carefully controlled by optimizing the conditions of silanization through the use of mixed silanes and selective mixing procedures. At this point, samples were exposed to bioreagents and changes in the shallow dielectric constant around the particles were observed by dark-field spectroscopy. Biological binding of high affinity systems (biotin/streptavidin and antigen/antibody) was subsequently investigated by optimizing coating layers, receptor concentration profiling, and finally quantitative determination of the analyte of interest, which in this case was a small organic molecule—the widely used, synthetic anabolic steroid called stanozolol. For this system, high specificity was achieved (>97%) through extensive nonspecific binding tests, with a sensitivity measurable to a level below the minimum required performance level (MRPL) as determined by standard chromatographic methods. Analytical best-fit parameters of Hillslope and regression coefficient are also commented on for the final LSPR biosensor. The LSPR biosensor showed good reproducibility (<5% RSD) and allowed for rapid preparation of calibration curves and determination of the analyte (measurement time of each sample ca. 2 min). As an alternative method for quantitative steroidal analysis, this approach significantly simplifies the detection setup while reducing the cost of analysis. In addition the system maintains comparable sensitivity to standard surface plasmon resonance methods and offers great potential for miniaturization and development of multiplexed devices. Figure Schematic of sensor configuration indicating both min and max controls and associatedexample localized resonance curves Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Modulation of proteins adsorption onto the surface of chitosan complexed with anionic copolymers. Real time analysis by surface plasmon resonance

The interpolyelectrolyte complex formation between chitosan and anionic polyacrylic derivatives, bearing sulfonic moieties, as well as the protein adsorption onto the chitosan/polyacrylic complexes were studied by surface plasmon resonance (SPR) optical biosensor. This unique technique allows a real time monitoring of different surface molecular interactions with very high sensitivity. The acrylic macromolecules are two families of copolymers of 2-acrylamido-2-methylpropane sulfonic acid (AMPS) and, respectively, 2-hydroxyethylmethacrylate (HEMA) and N,N'-dimethylacrylamide (DMAA). The complexation process was evaluated through the SPR measurements resulting from the flowing of polyacrylic aqueous solution over the sensor previously coated with chitosan. The SPR was able to differentiate strong ionic bonds from other weak and reversible interactions. By means of the coated sensors (uncomplexed and the whole series of complexed chitosan), SPR cold be used for a simple "in vitro" protein adsorption analysis, by flowing aqueous solutions of albumin and fibrinogen. While both proteins were adsorbed on the uncomplexed chitosan, the complexed coatings exhibited different and very promising behaviors. In particular, they showed no adsorption or only selective adsorption of albumin.     

High-sensitivity biosensors fabricated by tailoring the localized surface plasmon resonance property of core-shell gold nanorods

An enhanced sensitive biosensor has been developed to detect biological targets by tailoring the localized surface plasmon resonance property of core–shell gold nanorods. In this new concept, a shell layer is produced on gold nanorods by generating a layer of chalcogenide on the gold nanorod surface after attachment of the recognition reagent, namely, goat IgG and antigen of schistosomiasis japonica. The bioactivity of these attached biomolecules is retained and the sensitivity of this biosensor is thus enhanced significantly. The plasmonic properties of the gold nanorods attached with the biomolecules can be adjusted and the plasmon resonance wavelength can be red-shifted up to several hundred nanometers in the visible or near infrared (NIR) region, which is extremely important to biosensing applications. This leads to a lager red-shift in the localized surface plasmon resonance absorption compared to the original gold nanorod-based sensor and hence offers greatly enhanced sensitivity in the detection of schistosomiasis japonica. The human serum infected with schistosomiasis japonica diluted to 1:50,000 (volume ratio, serum/buffer solution) can be detected readily. The technique offers enhanced sensitivity and can be easily extended to other sensing applications based on not only immuno-recognition but also other types of specific reactions.     

Electrochemically controlled detection of adrenaline on poly(2‐aminobenzylamine) thin films by surface plasmon resonance spectroscopy and quartz crystal microbalance

In this study, we present an electrochemically controlled surface plasmon resonance (EC‐SPR) biosensor to detect adrenaline on poly(2‐aminobenzylamine) (P2ABA) thin films. The P2ABA thin films are stable and display electroactivity in a neutral PBS solution. Specific detection of adrenaline was performed on P2ABA thin films because the benzylamine groups in the P2ABA structure could specifically react with adrenalines. Adrenaline was detected in real time by EC‐SPR spectroscopy, which provides an EC‐SPR reflectivity change on the P2ABA thin film upon adrenaline injection. The measured responses were quite different from those for uric acid and ascorbic acid, which are major interferences in adrenaline detection. The electrochemically applied potential facilitates the specific detection of adrenaline. In addition, the detection of adrenaline on the P2ABA thin films was investigated by a quartz crystal microbalance technique. The detection limit for adrenaline at open circuit potential was 10 pM. The present study provides a useful information on the detection of adrenaline on the P2ABA thin films. Copyright © 2013 John Wiley & Sons, Ltd.     

Multiple plasmonic effect on photocurrent generation of metal‐loaded titanium dioxide composite/dye films on gold grating surface

We demonstrate the multiple plasmonic effect on the photocurrent properties of photoanodes containing Ag or Au nanoparticles (NPs) loaded onto titanium dioxide film (Ag–TiO₂ or Au–TiO₂) on Au grating surfaces. Ag–TiO₂ or Au–TiO₂ nanocomposite particles are prepared by a flame spray pyrolysis route. The structures and morphologies of the prepared products are characterized by high‐resolution transmission electron microscopy. The Ag–TiO₂ or Au–TiO₂ composite NPs are deposited by spin coating onto the Au grating surfaces. The photoanode electrode is a layered structure of blu‐ray disc‐recordable grating substrate/Au/Ag (or Au)–TiO₂/dye/electrolyte/indium‐tin oxide. The plasmonic effect is induced when Ag or Au NPs are located within the propagating surface plasmon (SP) field on the Au grating surface. The short‐circuit photocurrent is increased by exciting the grating‐coupled propagating SP on the Au gratings and is further enhanced by positioning the Ag or Au NPs within the grating‐coupled SP field. Copyright © 2014 John Wiley & Sons, Ltd.     

A novel detection of single-stranded DNA binding protein based on ss-DNA modified chip using surface plasmon resonance microscopy

An ss-DNA gold chip was prepared based on self-assembly of the thiol-derivatized oligonucleotide,and used for thedetermination of single-stranded binding protein(SSB)by surface plasmon resonance microscopy(SPR).The experiment resultsshowed that SSB binds ss-DNA with high specificity,and relative signal of SPR response is proportional to the concentration of SSBin the range of 0.1-100 ng/mL with a detection limit(S/N=3)of 0.07 ng/mL.     

Design of a ruthenium(III) immobilized affinity material based on a β‐cyclodextrin‐functionalized poly(glycidyl methacrylate‐ethylene dimethacrylate) monolith for the enrichment of hippuric acid

Immobilized metal affinity chromatography has drawn great attention as a widespread separation and purification approach. In this work, ruthenium was firstly introduced into the preparation of immobilized metal affinity chromatography considering its affinity to N,O‐donor ligands. A β‐cyclodextrin‐functionalized poly(glycidyl methacrylate‐ethylene dimethacrylate) monolith was designed and employed as the supporting material in immobilized metal affinity chromatography. Thiosemicarbazide was introduced into the synthesis process, which not only acted as a bridge between β‐cyclodextrin and glycidyl methacrylate, but also chelated with ruthenium because of its mixed hard‐soft donor characteristics. The developed monolithic ruthenium(III)‐immobilized metal affinity chromatography column was utilized for the adsorption and separation of hippuric acid, a biological indicator of toluene exposure. To achieve high extraction capacity, the parameters affecting the extraction efficiency were investigated with an orthogonal experiment design, L9 (3⁴). Under the optimized conditions, the enrichment factor of hippuric acid was 16.7‐fold. The method reproducibility was investigated in terms of intra‐ and interday precisions with relative standard deviations lower than 8.7 and 9.5%, respectively. In addition, ruthenium(III)‐immobilized metal affinity chromatography material could be used for up to 80 extractions without an apparent change in extraction recovery.     

Sensitivity of transmission surface plasmon resonance (T-SPR) spectroscopy: self-assembled multilayers on evaporated gold island films

The distance dependence of the localized surface plasmon (SP) extinction of discontinuous gold films is a crucial issue in the application of transmission surface plasmon resonance (T-SPR) spectroscopy to chemical and biological sensing. This derives from the usual sensing configuration, whereby an analyte binds to a selective receptor layer on the gold film at a certain distance from the metal surface. In the present work the distance sensitivity of T-SPR spectroscopy of 1.0-5.0 nm (nominal thickness) gold island films evaporated on silanized glass substrates is studied by using coordination-based self-assembled multilayers, offering thickness tuning in the range from approximately 1 to approximately 15 nm. The morphology, composition and optical properties of the Au/multilayer systems were studied at each step of multilayer construction. High-resolution scanning electron microscopy (HRSEM) showed no apparent change in the underlying Au islands, while atomic force microscopy (AFM) indicated flattening of the surface topography during multilayer construction. A regular growth mode of the organic layers was substantiated by X-ray photoelectron spectroscopy (XPS). Transmission UV-visible spectra showed an increase of the extinction and a red shift of the maximum of the SP band upon addition of organic layers, establishing the distance dependence of the Au SP absorbance. The distance sensitivity of T-SPR spectroscopy can be varied by using characteristic substrate parameters, that is, Au nominal thickness and annealing. In particular, effective sensitivity up to a distance of at least 15 nm is demonstrated with 5 nm annealed Au films. It is shown that intensity measurements, particularly in the plasmon intensity change (PIC) presentation, provide an alternative to the usually measured plasmon band position, offering good accuracy and the possibility of measuring at a single wavelength. The present distance sensitivity results provide the basis for further development of T-SPR transducers based on receptor-coated Au island films.