Coupling Magnetic Single-Crystal Co2Mo3O8 with Ultrathin Nitrogen-Rich Carbon Layer for Oxygen Evolution Reaction

Transition-metal oxides as electrocatalysts for the oxygen evolution reaction (OER) provide a promising route to face the energy and environmental crisis issues. Although palmeirite oxide A₂Mo₃O₈ as OER catalyst has been explored, the correlation between its active sites (tetrahedral or octahedral) and OER performance has been elusive. Now, magnetic Co₂Mo₃O₈@NC-800 composed of highly crystallized Co₂Mo₃O₈ nanosheets and ultrathin N-rich carbon layer is shown to be an efficient OER catalyst. The catalyst exhibits favorable performance with an overpotential of 331 mV@10 mA cm⁻² and 422 mV@40 mA cm⁻², and a full water-splitting electrolyzer with it as anode catalyst shows a cell voltage of 1.67 V@10 mA cm⁻² in alkaline. Combined HAADFSTEM, magnetic, and computational results show that factors influencing the OER performance can be attributed to the tetrahedral Co sites (high spin, t₂³e⁴), which improve the OER kinetics of rate-determining step to form *OOH.     

Controlled Synthesis of Cr‐Co0.85Se Nanoarrays for Water Splitting at an Ultralow Cell Voltage of 1.43 V

Water splitting has attracted more and more attention as a promising strategy for the production of clean hydrogen fuel. In this work, a new synthesis strategy was proposed, and Co_0.85Se was synthesized on nickel foam as the main matrix. The doping of appropriate Cr amount into the target of Co_0.85Se and the Cr‐Co_0.85Se resulted in an excellent electrochemical performance. The doping of Cr introduces Cr³⁺ ions which substitute Co²⁺ and Co³⁺ ions in Co_0.85Se, so that the lattice parameters of the main matrix were changed. It is worth noting that the Cr0.15‐Co_0.85Se/NF material exhibits an excellent performance in the oxygen evolution reaction (OER) test. When the current density reaches 50 mA cm^?2 for OER, the overpotential is only 240 mV. For the hydrogen evolution reaction (HER) tests, the overpotential is only 117 mV to drive 10 mA cm^?2 of current density. Moreover, when the Cr0.15‐Co_0.85Se/NF material is used as a two‐electrode device for whole water splitting, the required cell voltage is only 1.43 V to reach a current density of 10 mA cm^?2, which is among the lowest values of the published catalysts up to now. In addition, the Cr0.15‐Co_0.85Se/NF catalyst also exhibits excellent stability during a long period of water splitting. The experimental result demonstrates that the change of the lattice structure has an obvious influence on the electrocatalytic activity of the material. When an external electric field is applied, it facilitates the rapid electron transfer rate and enhances the electrocatalytic performance and stability of the material.     

Plasma‐Engraved Co3O4 Nanosheets with Oxygen Vacancies and High Surface Area for the Oxygen Evolution Reaction

Co₃O₄, which is of mixed valences Co²⁺ and Co³⁺, has been extensively investigated as an efficient electrocatalyst for the oxygen evolution reaction (OER). The proper control of Co²⁺/Co³⁺ ratio in Co₃O₄ could lead to modifications on its electronic and thus catalytic properties. Herein, we designed an efficient Co₃O₄‐based OER electrocatalyst by a plasma‐engraving strategy, which not only produced higher surface area, but also generated oxygen vacancies on Co₃O₄ surface with more Co²⁺ formed. The increased surface area ensures the Co₃O₄ has more sites for OER, and generated oxygen vacancies on Co₃O₄ surface improve the electronic conductivity and create more active defects for OER. Compared to pristine Co₃O₄, the engraved Co₃O₄ exhibits a much higher current density and a lower onset potential. The specific activity of the plasma‐engraved Co₃O₄ nanosheets (0.055 mA cm^?2_BET at 1.6 V) is 10 times higher than that of pristine Co₃O₄, which is contributed by the surface oxygen vacancies.     

Active Electron Density Modulation of Co3O4‐Based Catalysts Enhances their Oxygen Evolution Performance

Despite the fact that many strategies have been developed to improve the efficiency of the oxygen evolution reaction (OER), the precise modulation of the surface electronic properties of catalysts to improve their catalytic activity is still challenging. Herein, we demonstrate that the surface active electron density of Co₃O₄ can be effectively regulated by an argon‐ion irradiation method. X‐ray photoelectron and synchrotron x‐ray absorption spectroscopy, UV photoelectron spectrometry, and DFT calculations show that the surface active electron density band center of Co₃O₄ has been upshifted, leading to a significantly enhanced absorption capability of the oxo group. The optimized Co₃O₄‐based catalysts exhibit an excellent overpotential of 260 mV at 10 mA cm^?2 and Tafel slope of 54 mV dec^?1, superior to the capability of the benchmark RuO₂, representing one of the best Co‐based OER catalysts. This approach could guide the future rational design and discovery of ideal electrocatalysts.     

NixCo3‐xO4 Nanoneedle Arrays Grown on Ni Foam as an Efficient Bifunctional Electrocatalyst for Full Water Splitting

Developing highly active, stable and robust electrocatalysts based on earth‐abundant elements for oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) is important for many renewable energy conversion processes. Herein, Ni_xCo_3‐xO₄ nanoneedle arrays grown on 3D porous nickel foam (NF) was synthesized as a bifunctional electrocatalyst with OER and HER activity for full water splitting. Benefiting from the advantageous structure, the composite exhibits superior OER activity with an overpotential of 320 mV achieving the current density of 10 mA cm^?2. An exceptional HER activity is also acquired with an overpotential of 170 mV at the current density of 10 mA cm^?2. Furthermore, the catalyst also shows the superior activity and stability for 20 h when used in the overall water splitting cell. Thus, the hierarchical 3D structure composed of the 1D nanoneedle structure in Ni_xCo_3‐xO₄/NF represents an avenue to design and develop highly active and bifunctional electrocatalysts for promising energy conversion.     

Heterostructured Inter‐Doped Ruthenium–Cobalt Oxide Hollow Nanosheet Arrays for Highly Efficient Overall Water Splitting

The development of transition‐metal‐oxides (TMOs)‐based bifunctional catalysts toward efficient overall water splitting through delicate control of composition and structure is a challenging task. Herein, the rational design and controllable fabrication of unique heterostructured inter‐doped ruthenium–cobalt oxide [(Ru–Co)O_x] hollow nanosheet arrays on carbon cloth is reported. Benefiting from the desirable compositional and structural advantages of more exposed active sites, optimized electronic structure, and interfacial synergy effect, the (Ru–Co)O_x nanoarrays exhibited outstanding performance as a bifunctional catalyst. Particularly, the catalyst showed a remarkable hydrogen evolution reaction (HER) activity with an overpotential of 44.1 mV at 10 mA cm^?2 and a small Tafel slope of 23.5 mV dec^?1, as well as an excellent oxygen evolution reaction (OER) activity with an overpotential of 171.2 mV at 10 mA cm^?2. As a result, a very low cell voltage of 1.488 V was needed at 10 mA cm^?2 for alkaline overall water splitting.     

Molybdenum Carbide‐Embedded Multichannel Hollow Carbon Nanofibers as Bifunctional Catalysts for Water Splitting

With the environmental pollution and non‐renewable fossil fuels, it is imperative to develop eco‐friendly, renewable, and highly efficient electrocatalysts for sustainable energy. Herein, a simple electrospinning process used to synthesis Mo₂C‐embedded multichannel hollow carbon nanofibers (Mo₂C‐MCNFs) and followed by the pyrolysis process. As prepared lotus root‐like nanoarchitecture could offer rich porosity and facilitate the electrolyte infiltration, the Mo₂C‐MCNFs delivered favourable catalytic activity for HER and OER. The resultant catalysts exhibit low overpotentials of 114 mV and 320 mV at a current density of 10 mA cm^?2 for HER and OER, respectively. Furthermore, using the Mo₂C‐MCNFs catalysts as a bifunctional electrode toward overall water splitting, which only needs a small cell voltage of 1.68 V to afford a current density of 10 mA cm^?2 in the home‐made alkaline electrolyzer. This interesting work presents a simple and effective strategy to further fabricating tunable nanostructures for energy‐related applications.     

Synthesis of a Hierarchically Porous C/Co3O4 Nanostructure with Boron Doping for Oxygen Evolution Reaction

Fabricating a low‐cost and highly efficient electrocatalyst is of importance for the development of renewable energy devices. In this work, we have synthesized an ultrafine cobalt oxide nanocatalyst (5–10 nm) doped with boron (BC/Co₃O₄) by using a metal–organic framework as a precursor, which exhibits an excellent catalytic activity for oxygen evolution reaction (OER). Owing to the improvement of accessible active sites by boron doping, the synthesized catalyst can reach a current density of 10 mA cm^?2 at 1.54 V with a low overpotential of 310 mV, superior than those of commercial RuO₂ and N‐doped C/Co₃O₄. This work provides a facile way to develop highly efficient catalysts for electrochemical reactions.     

Synthesis of Tri‐functional Core‐shell CuO@carbon Quantum Dots@carbon Hollow Nanospheres Heterostructure for Non‐enzymatic H2O2 Sensing and Overall Water Splitting Applications

A core‐shell structure with CuO core and carbon quantum dots (CQDs) and carbon hollow nanospheres (CHNS) shell was prepared through facile in‐situ hydrothermal process. The composite was used for non‐enzymatic hydrogen peroxide sensing and electrochemical overall water splitting. The core‐shell structure was established from the transmission electron microscopy image analysis. Raman and UV‐Vis spectroscopy analysis confirmed the interaction between CuO and CQDs. The electrochemical studies showed the limit of detection and sensitivity of the prepared composite as 2.4 nM and 56.72 μA μM^?1 cm^?2, respectively. The core‐shell structure facilitated better charge transportation which in turn exhibited elevated electro‐catalysis towards hydrogen evolution reaction (HER), oxygen evolution reaction (OER) and overall water splitting. The overpotential of 159 mV was required to achieve 10 mA cm^?2 current density for HER and an overpotential of 322 mV was required to achieve 10 mA cm^?2 current density for OER in 1.0 M KOH. A two‐electrode system was constructed for overall water splitting reaction, which showed 10 and 50 mA cm^?2 current density at 1.83 and 1.96 V, respectively. The prepared CuO@CQDs@CHNS catalyst demonstrated excellent robustness in HER and OER catalyzing condition along with overall water splitting reaction. Therefore, the CuO@CQDs@CHNS could be considered as promising electro‐catalyst for H₂O₂ sensing, HER, OER and overall water splitting.     

Pomegranate‐Inspired Design of Highly Active and Durable Bifunctional Electrocatalysts for Rechargeable Metal–Air Batteries

Rational design of highly active and durable electrocatalysts for oxygen reactions is critical for rechargeable metal–air batteries. Herein, we report the design and development of composite electrocatalysts based on transition metal oxide nanocrystals embedded in a nitrogen‐doped, partially graphitized carbon framework. Benefiting from the unique pomegranate‐like architecture, the composite catalysts possess abundant active sites, strong synergetic coupling, enhanced electron transfer, and high efficiencies in the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). The Co₃O₄‐based composite electrocatalyst exhibited a high half‐wave potential of 0.842 V for ORR, and a low overpotential of only 450 mV at the current density of 10 mA cm^?2 for OER. A single‐cell zinc–air battery was also fabricated with superior durability, holding great promise in the practical implementation of rechargeable metal–air batteries.     

Hierarchical NiCo2O4 Hollow Microcuboids as Bifunctional Electrocatalysts for Overall Water‐Splitting

Bifunctional electrocatalysts for the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) in alkaline electrolyte may improve the efficiency of overall water splitting. Nickel cobaltite (NiCo₂O₄) has been considered a promising electrode material for the OER. However, NiCo₂O₄ that can be used as an electrocatalyst in HER has not been studied yet. Herein, we report self‐assembled hierarchical NiCo₂O₄ hollow microcuboids for overall water splitting including both the HER and OER reactions. The NiCo₂O₄ electrode shows excellent activity toward overall water splitting, with 10 mA cm^?2 water‐splitting current reached by applying just 1.65 V and 20 mA cm^?2 by applying just 1.74 V across the two electrodes. The synthesis of NiCo₂O₄ microflowers confirms the importance of structural features for high‐performance overall water splitting.     

Dual Role of Silver Moieties Coupled with Ordered Mesoporous Cobalt Oxide towards Electrocatalytic Oxygen Evolution Reaction

Herein, we show that the performance of mesostructured cobalt oxide electrocatalyst for oxygen evolution reaction (OER) can be significantly enhanced by coupling of silver species. Various analysis techniques including pair distribution function and Rietveld refinement, X‐ray absorption spectroscopy at synchrotron as well as advanced electron microscopy revealed that silver exists as metallic Ag particles and well‐dispersed Ag₂O nanoclusters within the mesostructure. The benefits of this synergy are twofold for OER: highly conductive metallic Ag improves the charge transfer ability of the electrocatalysts while ultra‐small Ag₂O clusters provide the centers that can uptake Fe impurities from KOH electrolyte and boost the catalytic efficiency of Co–Ag oxides. The current density of mesostructured Co₃O₄ at 1.7 V_RHE is increased from 102 to 211 mA cm^?2 with incorporation of silver spices. This work presents the dual role of silver moieties and demonstrates a simple method to increase the OER activity of Co₃O₄.     

A Surface‐Oxide‐Rich Activation Layer (SOAL) on Ni2Mo3N for a Rapid and Durable Oxygen Evolution Reaction

The oxygen evolution reaction (OER) is key to renewable energy technologies such as water electrolysis and metal–air batteries. However, the multiple steps associated with proton‐coupled electron transfer result in sluggish OER kinetics and catalysts are required. Here we demonstrate that a novel nitride, Ni₂Mo₃N, is a highly active OER catalyst that outperforms the benchmark material RuO₂. Ni₂Mo₃N exhibits a current density of 10 mA cm^?2 at a nominal overpotential of 270 mV in 0.1 m KOH with outstanding catalytic cyclability and durability. Structural characterization and computational studies reveal that the excellent activity stems from the formation of a surface‐oxide‐rich activation layer (SOAL). Secondary Mo atoms on the surface act as electron pumps that stabilize oxygen‐containing species and facilitate the continuity of the reactions. This discovery will stimulate the further development of ternary nitrides with oxide surface layers as efficient OER catalysts for electrochemical energy devices.     

Fe/Co‐based Bimetallic MOF‐derived Co3Fe7@NCNTFs Bifunctional Electrocatalyst for High‐Efficiency Overall Water Splitting

Electrocatalytic water splitting to produce hydrogen and oxygen is regarded as one of the most promising methods to generate clean and sustainable energy for replacing fossil fuels. However, the design and development of an efficient bifunctional catalyst for simultaneous generation of hydrogen and oxygen remains extremely challenging yet is critical for the practical implementation of water electrolysis. Here, we report a facile method to fabricate novel N‐doped carbon nanotube frameworks (NCNTFs) by the pyrolysis of a bimetallic metal organic framework (MIL‐88‐Fe/Co). The resultant electrocatalyst, Co₃Fe₇@NCNTFs, exhibits excellent oxygen evolution reaction (OER) activity, achieving 10 mA/cm² at a low overpotential of just 264 mV in 1 M KOH solution, and 197 mV for the hydrogen evolution reaction. The high electrocatalytic activity arises from the synergistic effect between the chemistry of the Co₃Fe₇ and the NCNTs coupled to the novel framework structure. The remarkable electrocatalytic performance of our bifunctional electrocatalyst provides a promising pathway to high‐performance overall water splitting and electrochemical energy devices.     

General π‐Electron‐Assisted Strategy for Ir,Pt, Ru,Pd, Fe,Ni Single‐Atom Electrocatalysts with Bifunctional Active Sites for Highly Efficient Water Splitting

Both the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER) are crucial to water splitting, but require alternative active sites. Now, a general π‐electron‐assisted strategy to anchor single‐atom sites (M=Ir, Pt, Ru, Pd, Fe, Ni) on a heterogeneous support is reported. The M atoms can simultaneously anchor on two distinct domains of the hybrid support, four‐fold N/C atoms (M@NC), and centers of Co octahedra (M@Co), which are expected to serve as bifunctional electrocatalysts towards the HER and the OER. The Ir catalyst exhibits the best water‐splitting performance, showing a low applied potential of 1.603 V to achieve 10 mA cm^?2 in 1.0 m KOH solution with cycling over 5 h. DFT calculations indicate that the Ir@Co (Ir) sites can accelerate the OER, while the Ir@NC₃ sites are responsible for the enhanced HER, clarifying the unprecedented performance of this bifunctional catalyst towards full water splitting.     

Carbon Nanotubes Decorated with CoP Nanocrystals: A Highly Active Non‐Noble‐Metal Nanohybrid Electrocatalyst for Hydrogen Evolution

The development of effective and inexpensive hydrogen evolution reaction (HER) electrocatalysts for future renewable energy systems is highly desired. The strongly acidic conditions in proton exchange membranes create a need for acid‐stable HER catalysts. A nanohybrid that consists of carbon nanotubes decorated with CoP nanocrystals (CoP/CNT) was prepared by the low‐temperature phosphidation of a Co₃O₄/CNT precursor. As a novel non‐noble‐metal HER catalyst operating in acidic electrolytes, the nanohybrid exhibits an onset overpotential of as low as 40 mV, a Tafel slope of 54 mV dec^?1, an exchange current density of 0.13 mA cm^?2, and a Faradaic efficiency of nearly 100 %. This catalyst maintains its catalytic activity for at least 18 hours and only requires overpotentials of 70 and 122 mV to attain current densities of 2 and 10 mA cm^?2, respectively.     

General π‐Electron‐Assisted Strategy for Ir,Pt, Ru,Pd, Fe,Ni Single‐Atom Electrocatalysts with Bifunctional Active Sites for Highly Efficient Water Splitting

Both the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER) are crucial to water splitting, but require alternative active sites. Now, a general π‐electron‐assisted strategy to anchor single‐atom sites (M=Ir, Pt, Ru, Pd, Fe, Ni) on a heterogeneous support is reported. The M atoms can simultaneously anchor on two distinct domains of the hybrid support, four‐fold N/C atoms (M@NC), and centers of Co octahedra (M@Co), which are expected to serve as bifunctional electrocatalysts towards the HER and the OER. The Ir catalyst exhibits the best water‐splitting performance, showing a low applied potential of 1.603 V to achieve 10 mA cm^?2 in 1.0 m KOH solution with cycling over 5 h. DFT calculations indicate that the Ir@Co (Ir) sites can accelerate the OER, while the Ir@NC₃ sites are responsible for the enhanced HER, clarifying the unprecedented performance of this bifunctional catalyst towards full water splitting.     

Tailoring Oxygen Vacancy on Co3O4 Nanosheets with High Surface Area for Oxygen Evolution Reaction?

Electrochemical water splitting requires efficient water oxidation catalysts to accelerate the sluggish kinetics of water oxidation reaction. Here, we designed an efficient Co₃O₄ electrocatalyst using a pyrolysis strategy for oxygen evolution reaction (OER). Morphological characterization confirmed the ultra-thin structure of nanosheet. Further, the existence of oxygen vacancies was obviously evidenced by the X-ray photoelectron spectroscopy and electron spin resonance spectroscopy. The increased surface area of Co₃O₄ ensures more exposed sites, whereas generated oxygen vacancies on Co₃O₄ surface create more active defects. The two scenarios were beneficial for accelerating the OER across the interface between the anode and electrolyte. As expected, the optimized Co₃O₄ nanosheets can catalyze the OER efficiently with a low overpotential of 310 mV at current density of 10 mA/cm² and remarkable long-term stability in 1.0 mol/L KOH.     

A Titanium‐Doped SiOx Passivation Layer for Greatly Enhanced Performance of a Hematite‐Based Photoelectrochemical System

This study introduces an in situ fabrication of nanoporous hematite with a Ti‐doped SiO_x passivation layer for a high‐performance water‐splitting system. The nanoporous hematite with a Ti‐doped SiO_x layer (Ti‐(SiO_x/np‐Fe₂O₃)) has a photocurrent density of 2.44 mA cm^?2 at 1.23 V_RHE and 3.70 mA cm^?2 at 1.50 V_RHE. When a cobalt phosphate co‐catalyst was applied to Ti‐(SiO_x/np‐Fe₂O₃), the photocurrent density reached 3.19 mA cm^?2 at 1.23 V_RHE with stability, which shows great potential of the use of the Ti‐doped SiO_x layer with a synergistic effect of decreased charge recombination, the increased number of active sites, and the reduced hole‐diffusion pathway from the hematite to the electrolyte.     

Magnetic Field-Enhanced Electrocatalytic Oxygen Evolution on a Mixed-Valent Cobalt-Modulated LaCoO3 Catalyst

Extensive efforts to enhance the oxygen evolution reaction (OER) catalytic performance of transition metal oxides mainly concentrate on the extrinsic morphology tailoring, lattice doping, and electrode interface optimizing. Nevertheless, little room is left for performance improvement using these methods and an obvious gap still exists compared to the precious metal catalysts. In this work, a novel “mixed-valent cobalt modulation” strategy is presented to enhance the electrocatalytic OER of perovskite LaCoO₃ (LCO) oxide. The valence transition of cobalt is realized by ethylenediamine post reduction procedure at room temperature, which further induces the variation of magnetic properties for LCO catalyst. The optimized LCO catalyst with Co²⁺/Co³⁺ of 1.98 % exhibits the best OER activity, and the overpotential at 10 mA cm⁻² current density is decreased by 170 mV compared pristine LCO. Impressively, the ferromagnetic LCO catalyst can perform magnetic OER enhancement. By application of an external magnetic field, the overpotential of LCO at 10 mA cm⁻² can be further decreased by 20 mV compared to that of under zero magnetic field, which arises from the enhanced energy states of electrons and accelerated electron transfer process driven by magnetic field. Our findings may provide a promising strategy to break the bottleneck for further enhancement of OER performance.