Enhanced peroxidase‐like activity of MMT‐supported cuprous oxide nanocomposites toward rapid colorimetric estimation of H2O2

Nanocomposites based on Cu₂O and Ca‐montmorillonite (Ca⁺‐MMT) with different composition were successfully prepared via a simple hydrothermal method. The as‐prepared Cu₂O‐MMT nanocomposites can rapidly catalytically oxidize the colorless chromogenic substrate, 3,3′,5,5′‐tetramethylbenzydine (TMB) into blue oxTMB with the aid of the H₂O₂ only in 30 s, which were observed by the naked eye. The reaction catalyzed by the Cu₂O‐MMT nanocomposites followed the Michaelis–Menten kinetics. Compared to the MMT or Cu₂O alone, Cu₂O‐MMT with different mass ratio exhibited an enhanced peroxidase‐like activity. The fabricated H₂O₂ sensor exhibited a good response to H₂O₂ with a linear detection range from 3 to 80 μM as well as a detection limit of 2.395 μM. Taking the advantages of the Cu₂O‐MMT nanocomposites, including outstanding peroxidase‐like activity and high sensitivity for colorimetric detection of H₂O₂, a colorimetric sensor based on the Cu₂O‐MMT nanocomposites was designed and used to rapidly detect H₂O₂ in a short time.     

Self‐Assembled Prussian Blue Nanoparticles Based Electrochemical Sensor for High Sensitive Determination of H2O2 in Acidic Media

In this paper, self‐assembled Prussian blue nanoparticles (PBNPs) on carbon ceramic electrode (CCE) were developed as a high sensitive hydrogen peroxide (H₂O₂) electrochemical sensor. The PBNPs film was prepared by a simple dipping method. The morphology of the PBNPs‐modified CCE was characterized by scanning electron microscopy (SEM). The self‐assembled PB film exhibited sufficient mechanical, electrochemical stability and high sensitivity in compare with other PB based H₂O₂ sensors. The sensor showed a good linear response for H₂O₂ over the concentration range 1 μM–0.26 mM with a detection limit of ca. 0.7 μM (S/N=3), and sensitivity of 754.6 mA M^?1 cm^?2. This work demonstrates the feasibility of self‐assembled PBNPs‐modified CCE for practical sensing applications.     

Noncovalent Assembly of Picket‐Fence Porphyrin on Carbon Nanotubes as Effective Peroxidase‐Like Catalysts for Detection of Hydrogen Peroxide in Beverages

A newly developed electrochemical sensor for determination of hydrogen peroxide (H₂O₂) in beverages using a water‐insoluble picket‐fence porphyrin (FeTpivPP) functionalized multiwalled carbon nanotubes (MWNTs) is demonstrated. Introduction of FeTpivPP on MWNTs led to enhanced electron transfer. As a new platform in electrochemical analysis, the resultant sensor showed excellent electrocatalytic activity toward the reduction of H₂O₂ due to the synergic effect between MWNTs and FeTpivPP, thus leading to highly sensitive amperometric sensing of H₂O₂ with a detection limit of 0.05 µmol L^?1. The developed method is successfully used to detect H₂O₂ in beverages and shows great promise for routine sensing applications.     

Hybridized Polyoxometalate‐Based Metal–Organic Framework with Ketjenblack for the Nonenzymatic Detection of H2O2

The rational design and development of efficient and affordable enzyme‐free electrocatalysts for electrochemical detection are of great significance for the large‐scale applications of sensor materials, and have aroused increasing research interest. Herein, we report that a typical polyoxometalate (POM)‐based metal–organic framework (NENU5) that was hybridized with ketjenblack (KB) was a highly efficient electrochemical catalyst that could be used for the highly sensitive nonenzymatic detection of H₂O₂. The composite catalyst exhibited superb electrochemical detection performance towards H₂O₂, including a broad linear range from 10–50 mm , a low detection limit of 1.03 μm , and a high sensitivity of 33.77 μA mm ⁻¹, as well as excellent selectivity and stability. These excellent electrocatalytic properties should be attributed to the unique redox activity of the POM, the high specific surface area of the metal–organic framework (MOF), the strong conductivity of KB, and the synergistic effects of the multiple components in the composites during the electrolysis of H₂O₂. This work provides a new pathway for the exploration of nonenzymatic electrochemical sensors.     

High Sensitive Microsensor Based on Organic‐Inorganic Composite for Two‐Dimensional Mapping of H2O2 by SECM

The present work describes the development of a selective, sensitive and stable sensing microsensor for scanning electrochemical microscopy (SECM) to measure H₂O₂ during electrochemical reduction of oxygen. The microsensor is based on graphene and Poly(3,4‐ethylenedioxythiophene) composite as support to iron (III) hexacyanoferrate (II) (PEDOT/graphene/Fe^III₄[Fe^II(CN)₆]₃ microsensor). The electrochemical properties of the PEDOT/graphene/Fe^III₄[Fe^II(CN)₆]₃ microsensor were investigated by cyclic voltammetry (CV) and scanning electrochemical microscopy (SECM). The PEDOT/graphene/Fe^III₄[Fe^II(CN)₆]₃ microsensor showed an excellent electrocatalytic activity toward hydrogen peroxide (H₂O₂) reduction with a diminution of the overpotential of about 500 mV in comparison to the process at a bare gold microelectrode. The microsensor presented excellent performance for two dimensional mapping of H₂O₂ by SECM in 0.1 mol L^?1 phosphate buffer solution (pH 7.0). Under optimized conditions, a linear response range from 1 up to 1000 µmol L^?1 was obtained with a sensitivity of 0.08 nA L µmol^?1 and limit of detection of 0.5 µmol L^?1.     

Highly Sensitive Electrochemical Hydrogen Peroxide Sensor Based on Iron Oxide‐Reduced Graphene Oxide‐Chitosan Modified with DNA‐Celestine Blue

The present study describes a novel and very sensitive electrochemical assay for determination of hydrogen peroxide (H₂O₂) based on synergistic effects of reduced graphene oxide‐ magnetic iron oxide nanocomposite (rGO‐Fe₃O₄) and celestine blue (CB) for electrochemical reduction of H₂O₂. rGO‐Fe₃O₄ nanocomposite was synthesized and characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X‐ray diffraction (XRD), electrochemical impedance spectroscopy and cyclic voltammetry. Chitosan (Chit) was used for immobilization of amino‐terminated single‐stranded DNA (ss‐DNA) molecules via a glutaraldehyde (GA) to the surface of rGO‐Fe₃O₄. The MTT (3‐(4,5‐Dim ethylt hiazol‐2‐yl)‐2,5‐diphenylt etrazolium bromide) results confirmed the biocompatibility of nanocomposite. Experimental parameters affecting the ss‐DNA molecules immobilization were optimized. Finally, by accumulation of the CB on the surface of the rGO‐Fe₃O₄‐Chit/ssDNA, very sensitive amperometric H₂O₂ sensor was fabricated. The electrocatalytic activity of the rGO‐Fe₃O₄‐Chit/DNA‐CB electrode toward H₂O₂ reduction was found to be very efficient, yielding very low detection limit (DL) of 42 nM and a sensitivity of 8.51 μA/μM. Result shows that complex matrices of the human serum samples did not interfere with the fabricated sensor. The developed sensor provided significant advantages in terms of low detection limit, high stability and good reproducibility for detection of H₂O₂ in comparison with recently reported electrochemical H₂O₂ sensors.     

Novel Nonenzymatic Hydrogen Peroxide Sensor Based on Ag/Cu2O Nanocomposites

The nanocomposites of Ag nanoparticles supported on Cu₂O were prepared and used for fabricating a novel nonenzymatic H₂O₂ sensor. The morphology and composition of the nanocomposites were characterized using the scanning electron microscope (SEM), transmission electron microscope (TEM), energy‐dispersive X‐ray spectrum (EDX) and X‐ray diffraction spectrum (XRD). The electrochemical investigations indicate that the sensor possesses an excellent performance toward H₂O₂. The linear range is estimated to be from 2.0 μM to 13.0 mM with a sensitivity of 88.9 μA mM^?1 cm^?2, a response time of 3 s and a low detection limit of 0.7 μM at a signal‐to‐noise ratio of 3. Additionally, the sensor exhibits good anti‐interference.     

Enzyme-free amperometric sensing of hydrogen peroxide and glucose at a hierarchical Cu2O modified electrode

In this paper, an enzyme-free amperometric electrochemical sensor was fabricated by casting Nafion-impregnated Cu₂O particles onto a glassy carbon electrode. A dual dependence of peak current on sweeping rate, which can be attributed for the accumulation of reaction products, was observed on the sensor. Electrochemical analysis of the particulate Cu₂O for detecting H₂O₂ and glucose is described, showing remarkable sensitivity in both cases. The estimated detection limits and sensitivities for H₂O₂ (0.0039 μM, 52.3 mA mM⁻¹ cm⁻²) and glucose (47.2 μM, 0.19 mA mM⁻¹ cm⁻²) suggest that the response for H₂O₂ detection was much higher than for glucose detection. Electron microscopy observation suggested that the hierarchical structures of Cu₂O resulting from self-assembly of nanocrystals are responsible for the specific electrochemical properties.     

Development of an AND Logic‐Gate‐Type Fluorescent Probe for Ratiometric Imaging of Autolysosome in Cell Autophagy

The concomitant detection of two biological events facilitates the highly selective and sensitive analysis of specific biological functions. In this article, we report an AND logic‐gate‐type fluorescent probe that can concurrently sense two biological events in living cells: H₂O₂ accumulation and acidification. The probe exhibits a unique fluorescence sensing mechanism, in which a xanthene fluorophore is oxidatively transformed to a xanthone derivative by H₂O₂, thereby resulting in a clear dual‐emission change. This transformation is significantly accelerated under weak acidic conditions, which enables the selective and sensitive detection of H₂O₂ production in an acidic cellular compartment. This unique sensing property was successfully applied to the ratiometric fluorescence imaging of autolysosome formation in selective mitochondrial autophagy (mitophagy), which highlights the utility of this novel probe in autophagy research.     

Synthesis of Ferrocene Based Naphthoquinones and its Application as Novel Non‐enzymatic Hydrogen Peroxide

At present, a highly sensitive hydrogen peroxide (H₂O₂) sensor is fabricated by ferrocene based naphthaquinone derivatives as 2,3‐Diferrocenyl‐1,4‐naphthoquinone and 2‐bromo‐3‐ferrocenyl‐1,4‐naphthoquinone. These ferrocene based naphthaquinone derivatives are characterized by H‐NMR and C‐NMR. The electrochemical properties of these ferrocene based naphthaquinone are investigated by cyclic voltammetry (CV), differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS) on modified glassy carbon electrode (GCE). The modified electrode with ferrocene based naphthaquinone derivatives exhibits an improved voltammetric response to the H₂O₂ redox reaction. 2‐bromo‐3‐ferrocenyl‐1,4‐naphthoquinone show excellent non‐enzymatic sensing ability towards H₂O₂ response with a detection limitation of 2.7 μmol/L a wide detection range from 10 μM to 400 μM in H₂O₂ detection. The sensor also exhibits short response time (1 s) and good sensitivity of 71.4 μA mM^?1 cm^?2 and stability. Furthermore, the DPV method exhibited very high sensitivity (18999 μA mM^?1 cm^?2) and low detection limit (0.66 μM) compared to the CA method. Ferrocene based naphthaquinone derivative based sensors have a lower cost and high stability. Thus, this novel non‐enzyme sensor has potential application in H₂O₂ detection.     

Prussian Blue Nanocubes‐SnO2 Quantum Dots‐Reduced Graphene Oxide Ternary Nanocomposite: An Efficient Non‐noble‐metal Electrocatalyst for Non‐enzymatic Detection of H2O2

Developing non‐noble‐metal electrocatalyst for non‐enzymatic H₂O₂ sensing is highly attractive. A facile, two‐step approach has been utilized for the synthesis of PBNCs/SnO₂ QDs/RGO ternary nanocomposite. TEM, SEM, XPS, and XRD techniques were used to the characterize the structural and morphological properties of synthesized ternary nanocomposite. The synthesized ternary nanocomposite has been examined as an electrode material for the electrochemical detection of H₂O₂ using the Amperometry technique. Under optimum conditions, PBNCs/SnO₂ QDs/RGO ternary nanocomposite performed very well in the electrocatalytic reduction of H₂O₂ with a linear dynamic range from 25–225 μM (R²=0.996) with a low detection limit of 71 nM (S/N=3). Compared to the recent literature, PBNCs/SnO₂QDs/RGO ternary nanocomposite based modified electrode exhibit a wider linear dynamic range with a low detection limit. Furthermore, PBNCs/SnO₂ QDs/RGO ternary nanocomposite based modified electrode showed an excellent anti‐interference ability against various common interfering agents. The practical applicability of this ternary nanocomposite based modified electrode was further extended to determine the H₂O₂ in tap water with acceptable recovery. The present performance of PBNCs/SnO₂ QDs/RGO ternary nanocomposite material towards H₂O₂ sensing might widen its application for developing a new type of non‐noble metal‐based non‐enzymatic electrochemical biosensors.     

μ‐Cyano‐1:2κ2C:N‐tetracyano‐1κ4C‐(5‐methyl‐5‐nitro‐3,7‐diazanonane‐1,9‐diamine‐2κ4N1,3,7,9)‐nitrosyl‐1κN‐copper(II)iron(II) dihydrate

The title binuclear complex, [CuFe(CN)₅(C₈H₂₁N₅O₂)(NO)]·2H₂O or [CuFe(nelin)(CN)₅(NO)]·2H₂O (nelin is 5‐methyl‐5‐nitro‐3,7‐di­aza­nonane‐1,9‐di­amine) consists of discrete binuclear mixed‐metal species, with a Cu centre linked to an Fe centre through a cyano bridge, and two water mol­ecules of crystallization. In the complex, the Cu^II ion is coordinated by five N atoms and has a distorted square‐pyramidal geometry. The Fe^II centre is in a distorted octahedral environment.     

Octahedral Cuprous Oxide Decorated Flexible Reduced Graphene Oxide Paper for Food Sensing Application

This work presents a simple method to fabricate an octahedral cuprous oxide (Cu₂O) decorated two-dimensional (2D) flexible rGOP electrode with filtration and electrodeposition strategies. The characteristic of the Cu₂O/rGOP electrodes was recorded by SEM, EDX, XPS, XRD, and Raman spectroscopy. The results clearly showed that Cu₂O was successfully electrodeposited on the surface of rGOP by controlling the electrodeposition potential without the introduction of any template or surfactant. The electrochemical characterizations of the Cu₂O/rGOP exhibited high electrocatalytic activity toward the reduction of H₂O₂. The linear detection range for the Cu₂O/rGOP flexible sensor was 5.0 μM to 5.5 mM, with a limit of detection of 1.27 μΜ. Subsequently, the developed flexible rGOP sensor was extended for H₂O₂ detection in milk samples for avoiding milk spoilage_. Such judicial preparation of rGOP as a sensing device will certainly pave the way for various other sensing applications including environmental and biomedical applications.     

An Enzyme‐free H2O2 Sensor Based on Poly(2‐Aminophenylbenzimidazole)/Gold Nanoparticles Coated Pencil Graphite Electrode

A poly(2‐aminophenylbenzimidazole)/gold nanoparticles (P2AB/AuNPs) coated disposable pencil graphite electrode (PGE) was fabricated as an enzyme‐free sensor for the H₂O₂ determination. P2AB/AuNPs and P2AB were successfully synthesized electrochemically on PGE in acetonitrile for the first time. The coatings were characterized by scanning electron microscopy, X‐ray diffraction spectroscopy, Energy‐dispersive X‐ray spectroscopy, Surface‐enhanced Raman spectroscopy, and UV‐Vis spectroscopy. AuNPs interacted with P2AB as carrier enhances the electrocatalytic activity towards reduction of H₂O₂. The analytical performance was evaluated in a 100 mM phosphate buffer solution at pH 6.5 by amperometry. The steady state current vs. H₂O₂ concentration is linear in the range of 0.06 to 100 mM (R²=0.992) with a limit of detection 3.67×10^?5 M at ?0.8 V vs. SCE and no interference is caused by ascorbic acid, dopamine, uric acid, and glucose. The examination for the sensitive determination of H₂O₂ was conducted in commercially available hair oxidant solution. The results demonstrate that P2AB/AuNPs/PGE has potential applications as a sensing material for quantitative determination of H₂O₂.     

Electrochemical Conversion of Magnetic Nanoparticles Using Disposable Working Electrode in a 3D‐Printed Electrochemical Cell

Exploration of new property/function of nanomaterials is always a strong impetus in the nanoscience field. Here, a new method of electrochemical conversion (ECC) of magnetic nanoparticles (MNPs) is proposed to endow MNPs with signal generation ability for sensing. Briefly, high potential was applied to split H₂O to generate acid, while Fe₃O₄ MNPs reacted with H⁺ and produce ferric/ferrous ions, which further reacted with K₄Fe(CN)₆ to yield Prussian blue (PB) through potential cycling. The ECC method worked well on both home‐made and commercial MNPs with different sizes. The generated PB possessed strong electrochemical activity for further applications. Interestingly, an uneven deposition of PB on working electrode and undesired contamination of the reference and counter electrodes were found when using commercial integrated three‐electrode chip. A 3D‐printed electrochemical cell was designed to facilitate the ECC and avoid drawbacks of commercial integrated electrode. The 3D‐printed electrochemical cell was proven to solve the problem above through spatial separation of electrodes and thus facilitated the ECC process. An electrochemical sensor for H₂O₂ detection based on the catalysis ability of ECC‐based PB exhibited a linear response from 5 μM to 1 mM, a high sensitivity of 269 μA mM^?1 cm^?2 and a low detection limit of 0.16 μM (S/N=3), which suggests its promising application prospect in electrochemistry‐related analysis.     

Porous Molybdenum Carbide Nanostructured Catalyst toward Highly Sensitive Biomimetic Sensing of H2O2

There are great challenges to fabricate a highly selective and sensitive enzyme‐free biomimetic sensor. Herein for the first time a unique nanostructure of porous molybdenum carbide impregnated in N‐doped carbon (p‐Mo₂C/NC) is synthesized by using SiO₂ nanocrystals‐templating method and is further used as an enzyme‐free electrochemical biosensor toward highly selective, sensitive detection of H₂O₂, of which the limit of detection, dynamic detection range and sensitivity accomplish as 0.22 μM, 0.05–4.5 mM and 577.14 μA mM^?1 cm^?2, respectively, and are much superior to the non‐porous molybdenum carbide impregnated in N‐doped carbon (Mo₂C/NC). The sensor is also used to monitor H₂O₂ released from A549 living cells. This work holds a great promise to be used to monitor the presence of H₂O₂ in biological research while offering an important knowledge to design a highly selective and sensitive biomimetic sensor by synthesizing a porous catalyst to greatly improve the reaction surface area rather than conventionally only relying on dispersing the catalyst material into porous carbon substrate.     

A Water Stable CdII‐based Metal‐Organic Framework as a Multifunctional Sensor for Selective Detection of Cu2+ and Cr2O72– Ions

A water stable tetrazolate‐containing metal‐organic framework, [Cd₂(L)(OH)(H₂O)₂]_n ( 1 ) [H₃L = 5‐(4‐(tetrazol‐5‐yl)phenyl)isophthalic acid], was synthesized under solvothermal conditions and structurally characterized. Compound 1 displays a three dimensional porous network with one dimensional tubular channels based on trinuclear cluster [Cd₃(μ₃‐OH)N₄C] units. Notably, 1 exhibits highly sensitive response to Cu²⁺ and Cr₂O₇^2– through luminescence quenching effects with the detection limit of 0.666 ppm for Cu²⁺ and 0.846 ppm for Cr₂O₇^2–, respectively. The possible mechanism of the luminescence quenching was discussed in detail.     

Poly[[μ3‐2‐(carboxylatomethyl)benzoato‐κ3O1:O2:O2]bis(1H‐imidazole‐κN3)copper(II)]

In the title polymeric compound, [Cu(C₉H₆O₄)(C₃H₄N₂)₂]_n, the copper(II) cation occupies an N₂O₃ coordination sphere defined by two 1H‐imidazole (imid) ligands in trans positions and three carboxylate O atoms from three different 2‐(carboxylatomethyl)benzoate (hpt²⁻) dianions. The geometry is that of a square pyramid with one of the O atoms at the apex, bridging neighbouring metal centres into an [–ON₂CuO₂CuN₂O–] dinuclear unit. These units are in turn connected by hpt anions into a reticular mesh topologically characterized by two types of loops, viz. a four‐membered Cu₂O₂ diamond motif and a 32‐membered Cu₄O₈C₂₀ ring. The imid groups do not take part in the formation of the two‐dimensional structure, but take part in the N—H...O interactions. These arise only within individual planes, interplanar interactions being only of the van der Waals type.     

Diaquabis(quinoxaline‐2‐carboxylato‐κ2N1,O)copper(II)

In the title compound, [Cu(C₉H₅N₂O₂)₂(H₂O)₂], the Cu^II ion lies on an inversion centre and has an elongated centrosymmetric octahedral environment, equatorially trans‐coordinated by two N,O‐bidentate quinoxaline‐2‐carboxylate ligands and axially coordinated by two water O atoms. Symmetry‐related molecules are linked by strong O—H...O hydrogen bonds, involving the uncoordinated carboxyl O atom of the carboxylate group and the coordinated water molecules, to form a two‐dimensional network. Weak intermolecular C—H...N interactions also stabilize the crystal structure.     

Three different bonding modes of cyano groups in the coordination polymer [Cu(en)2(H2O)][Cu(en)2Ni2Cu2(CN)10]·2H2O (en is 1,2‐diaminoethane)

Partial reduction of the Cu^II ions in the aqueous system Cu^II–en–[Ni(CN)₄]^2? (1/1/1) (en is 1,2‐di­amino­ethane) yields a novel heterobimetallic mixed‐valence compound, poly­[[aqua­bis(1,2‐di­amino­ethane)copper(II)] [hexa‐μ‐cyano‐tetra­cyano­bis(1,2‐di­amino­ethane)­tricopper(I,II)­dinickel(II)] dihydrate], [Cu(C₂H₈N₂)₂(H₂O)][Ni₂Cu₃(CN)₁₀(C₂H₈N₂)₂]·2H₂O or [Cu(en)₂(H₂O)][Cu(en)₂Ni₂Cu₂(CN)₁₀]·2H₂O. The structure is formed by a negatively charged two‐dimensional array of the cyano complex [Cu(en)₂Ni₂Cu₂(CN)₁₀]_n^2n?, [Cu(en)₂(H₂O)]²⁺ complex cations and water mol­ecules of crystallization. These last are involved in a complicated hydrogen‐bonding system. The cyano groups act as terminal, μ₂‐bridging or μ₃‐bridging ligands.