A Novel Strategy for Quantifying Clopidogrel Using Square‐wave Voltammetry and a Boron‐doped Diamond Film

The voltammetric behavior of clopidogrel bisulfate (CLO), an antiplatelet agent, was investigated for the first time in the literature on a cathodically pretreated boron‐doped diamond electrode (CP‐BDDE) using cyclic (CV) and square‐wave voltammetry (SWV). It was observed an anodic peak for CLO, suitable for analytical purposes, at about 1.15 V (vs. Ag/AgCl (3.0 mol L^?1 KCl)) by CV in Britton‐Robinson buffer solution (pH 5.0). On the physical‐chemical characterization of the interface phenomena, it was proved that electrode reaction of the analyte was controlled by a diffusion process. At optimized square‐wave parameters (pulse amplitude of 60 mV, frequency of 30 Hz and scan increment of 3 mV), the obtained analytical curve was linear for the CLO concentration range from 0.60 to 60.0 μmol L^?1, with a detection limit of 0.60 μmol L^?1. The simple, rapid and greener analytical method, based on CP‐BDDE electrochemical sensor, was successfully applied in real samples (pharmaceuticals and urine).     

Electroanalytical Determination of Carbaryl in Natural Waters on Boron Doped Diamond Electrode

The anodic voltammetric behavior of carbaryl on a boron‐doped diamond electrode in aqueous solution is reported. The results, obtained by square‐wave voltammetry at 0.1 mol L^?1 Na₂SO₄ and pH 6.0, allow the development of a method to determine carbaryl, without any previous step of extraction, clean‐up, preconcentration or derivatization, in the range 2.5–30.0×10^?6 mol L^?1, with a detection limit of 8.2±0.2 μg L^?1 in pure water. The analytical sensitivity of this electrochemical method diminished slightly, from 3.07 mA mmol^?1 L to 2.90 mA mmol^?1L, when the electrolyte was prepared with water samples collected from two polluted points in an urban creek. In these conditions, the recovery efficiencies obtained were around 104%. The effect of other pesticides (fenthion and 4‐nitrophenol) was evaluated and found to exert a negligible influence on carbaryl determination. The square‐wave voltammetric data obtained for carbaryl were typical of an irreversible electrode process with mass transport control. The combination of square‐wave voltammetry and diamond electrodes is an interesting and desirable alternative for analytical determinations.     

First Electroanalytical Methodology for the Determination of Hordenine in Dietary Supplements using a Boron‐doped Diamond Electrode

The present work describes the first electrochemical investigation and a simple, rapid and modification‐free electroanalytical methodology for quantification of hordenine (a potent phenylethylamine alkaloid) using a boron‐doped diamond electrode. At optimized square‐wave voltammetric parameters, the observed oxidation peak current in 0.1 M HClO₄ at +1.33 V (vs. Ag/AgCl) increased linearly from 5.0 to 100 μg mL^?1 (3.0×10^?5–6.1×10^?4 M), with detection limit of 1.3 μg mL^?1 (7.8×10^?6 M). The applicability of the developed method was tested with the determination of hordenine in the commercial dietary supplement formulations.     

Electrochemical Oxidation of Ibuprofen and Its Voltammetric Determination at a Boron‐Doped Diamond Electrode

The electrochemical oxidation of ibuprofen at a boron‐doped diamond electrode (BDDE) and its voltammetric determination is reported for the first time. A well‐defined oxidation peak was observed at around 1.6 V in 0.1 mol L^?1 H₂SO₄ solution with 10 % (v/v) ethanol at the BDDE surface activated by either cathodic or anodic pretreatments. A differential‐pulse voltammetric method for the determination of ibuprofen in pharmaceutical formulations was optimized with a detection limit of 5 µmol L^?1 and compared with the British Pharmacopeia method.     

Electroanalytical Determination of Lidocaine in Pharmaceutical Preparations Using Boron‐Doped Diamond Electrodes

A new electroanalytical procedure was developed for the determination of lidocaine in commercial local anesthetics products containing lidocaine as the active ingredient. The procedure is based on the use of electrochemical methods as cyclic and square‐wave voltammetry, with boron‐doped diamond electrodes. The oxidation of lidocaine in Britton–Robinson buffer (0.1 mol L^?1) using this type of electrode gives rise to one irreversible peak in 1.68 V (versus Ag/AgCl). The detection and quantification limits obtained from pure water were 10.0 and 34.4 μg/L, respectively. The proposed electrochemical method was also successfully applied to the analysis of commercially available pharmaceutical preparations. The electrochemical responses of pharmaceutical preparations (gels) were identical to those of standard lidocaine. No influence of propyleneglycol present in the gels on the voltammetric responses was observed. Lidocaine recoveries ranged from 97.6% to 99.2%.     

Heavily Boron Doped Diamond Electrodes for Ultra Sensitive Determination of Ciprofloxacin in Human Urine

Ciprofloxacin is one of the most potent fluoroquinolone antibiotics in medical treatment with a widely effective antibacterial activity. Aim of the presented paper was to use boron doped diamond electrodes for a sensitive, simple and reliable voltammetric determination of ciprofloxacin in human urine samples. Prior to the electrochemical analyses, an optimal boron doping level was determined in order to achieve the highest sensitivity. A set of boron doped diamond electrodes with the doping level in the range from 0 to 20 000 ppm B/C was used for this purpose. Electrochemical behavior of ciprofloxacin was investigated using cyclic voltammetry in an ammonium acetate buffer (pH 5), where ciprofloxacin provided a well‐defined irreversible oxidation peak at a potential of + 1.15 V. Under optimal experimental conditions, the calibration curve obtained by square‐wave voltammetry was linear in a concentration range from 0.15 to 2.11 μmol/L (R²=0.9974). A very low limit of detection (0.05 μmol/L) was obtained for the BDD electrode with the highest doping level. The developed square wave method was successfully applied to the determination of ciprofloxacin in human urine samples with a very good recovery (from 97 to 102%).     

A Simple Approach to Simultaneous Electroanalytical Quantification of Acetaminophen and Tramadol Using a Boron‐doped Diamond Electrode in the Existence of Sodium Dodecyl Sulfate

The present work describes the individual, selective and simultaneous quantification of acetaminophen (ACP) and tramadol hydrochloride (TRA) using a modification‐free boron‐doped diamond (BDD) electrode. Cyclic voltammetric measurements revealed that the profile of the binary mixtures of ACP and TRA were manifested by two irreversible oxidation peaks at about +1.04 V (for ACP) and +1.61 V (for TRA) in Britton‐Robinson (BR) buffer pH 3.0. TRA oxidation peak was significantly improved in the presence of anionic surfactant, sodium dodecyl sulfate (SDS), while ACP signal did not change. By employing square‐wave stripping mode in BR buffer pH 3.0 containing 8×10^?4 mol L^?1 SDS after 30 s accumulation under open‐circuit voltage, the BDD electrode could be used for quantification of ACP and TRA simultaneously in the ranges 1.0–70 μg mL^?1 (6.6×10^?6–4.6×10^?4 mol L^?1) and 1.0–70 μg mL^?1 (3.3×10^?6–2.3×10^?4 mol L^?1), with detection limits of 0.11 μg mL^?1 (7.3×10^?7 mol L^?1) and 0.13 μg mL^?1 (4.3×10^?7 mol L^?1), respectively. The practical applicability of the proposed approach was tested for the individual and simultaneous quantification of ACP and/or TRA in the pharmaceutical dosage forms.     

Simultaneous Voltammetric Determination of Benzene,Toluene and Xylenes (BTX) in Water Using a Cathodically Pre‐treated Boron‐doped Diamond Electrode

An electrochemical method for the simultaneous determination of benzene, toluene and xylenes (BTX) in water was developed using square‐wave voltammetry (SWV). The determination of BTX was carried out using a cathodically pre‐treated boron‐doped diamond electrode (BDD) using 0.1 mol L^?1 H₂SO₄ as supporting electrolyte. In the SWV measurements using the BDD, the oxidation peak potentials of the total xylenes‐toluene and toluene‐benzene couples, present in ternary mixtures, display separations of about 100 and 200 mV, respectively. The attained detection limits for the simultaneous determination of benzene, toluene and total xylenes were 3.0×10^?7, 8.0×10^?7 and 9.1×10^?7 mol L^?1, respectively. The recovery values taken in ternary mixtures of benzene, toluene and total xylenes in aqueous solutions are 98.9 %, 99.2 % and 99.4 %, respectively.     

Voltammetry as the First Method for Direct Determination of a Novel Antagonist of A2A Adenosine Receptors

In this article, for the first time, the analytical method for determination of a novel antagonist of A_2A adenosine receptors (8‐(4‐methoxyphenyl)‐4‐oxo‐4,6,7,8‐tetrahydroimidazo[2,1‐c][1,2,4]triazine‐3‐carbohydrazide, namely IMT), which can be used as a drug for liver diseases, was presented. For this purpose a commercially available boron‐doped diamond electrode (BDDE) in combination with differential pulse voltammetry (DPV) was applied. It was found by cyclic voltammetry (CV) that IMT displays at BDDE, as a sensor, two well‐defined oxidation peaks at potentials of 0.81 and 1.18 V and one reduction peak at 1.1 V vs. Ag/AgCl in 0.1 mol L^?1 acetate buffer (pH 4.5±0.1). The oxidation and reduction mechanism of IMT was proposed. The developed DPV method allowed the successful determination of IMT in the range of 0.05–50 μmol L^?1 with detection limit equal to 0.0094 μmol L^?1 and without any chemical modifications and electrochemical pretreatment of the electrode surface. The proposed procedure allows the determination of IMT in vitro directly from urine samples.     

The Fabrication and Characterization of a Bismuth Nanoparticle Modified Boron Doped Diamond Electrode and Its Application to the Simultaneous Determination of Cadmium(II) And Lead(II)

We report the simultaneous electroanalytical determination of Pb²⁺ and Cd²⁺ by square‐wave anodic stripping voltammetry (SWASV) using a bismuth nanoparticle modified boron doped diamond (Bi‐BDD) electrode. Bi deposition was performed in situ with the analytes, from a solution of 0.1 mM Bi(NO₃)₃ in 0.1 M HClO₄ (pH 1.2), and gave detection limits of 1.9 μg L^?1 and 2.3 μg L^?1 for Pb(II) and Cd(II) respectively. Pb²⁺ and Cd²⁺ could not be detected simultaneously at a bare BDD electrode, whilst on a bulk Bi macro electrode (BiBE) the limits of detection for the simultaneous determination of Pb²⁺ and Cd²⁺ were ca. ten times higher.     

Highly Sensitive Electrochemical Sensor for Determination of Vitamin D in Mixtures of Water‐Ethanol

This paper describes the electrochemical determination of vitamin D₂ (ergocalciferol) and D₃ (cholecalciferol) in mixed organic/water solvent, using a glassy carbon electrode (GCE). The mixing ratio of organic/water solvent has an important influence on the electrocatalytic response of D vitamins on the surface of the glassy carbon electrode. Well‐defined peaks for Vitamin D₂ and D₃ were observed in a 40 % ethanol/60 % water solution with lithium perchlorate as the support electrolyte. This study demonstrated that the glassy carbon electrode is highly sensitive for the determination of vitamin D₂ and D₃, with a limit of detection of 0.13 and 0.118 µmol L^?1, respectively. No significant interference was seen for vitamins A, E and K in the detection of vitamin D.     

Sensitive Determination of the Diquat Herbicide in Fresh Food Samples on a Highly Boron‐Doped Diamond Electrode

The highly boron‐doped diamond electrode (HBDD) combined with square wave voltammetry (SWV) was used in the development of an analytical procedure for diquat determination in potato and sugar cane samples and lemon, orange, tangerine and pineapple juices. Preliminary experiments realised in a medium of 0.05 mol L^?1 Na₂B₄O₇ showed the presence of two voltammetric peaks around ?0.6 V and around ?1.0 V vs. Ag/AgCl/Cl^? 3.0 mol L^?1, where the first peak could be successfully used for analytical proposes due the facility in the electrode surface renovation. After the experimental and voltammetric optimisation, the calculated detection and quantification limits were 1.6×10^?10 mol L^?1 and 5.3×10^?10 mol L^?1 (0.057 µg L^?1 and 0.192 µg L^?1, respectively), which are lower than the maximum residue limit established for fresh food samples by the Brazilian Sanitary Vigilance Agency. The proposed methodology was used to determine diquat residues in potato and sugar cane samples and lemon, orange, tangerine and pineapple juices and the calculated recovery efficiencies indicated that the proposed procedure presents higher robustness, stability and sensitivity, good reproducibility, and is very adequate for diquat determination in complex samples.     

Electrochemical Characterization and Rapid Voltammetric Determination of Riluzole in Pharmaceuticals and Human Serum

The electrochemical oxidation of riluzole was investigated using cyclic and linear sweep voltammetry. Under optimized conditions, current and concentration showed linear dependence in Britton Robinson buffer at pH 3.00 for boron doped diamond and pH 3.00 phosphate buffers for glassy carbon electrodes. Differential pulse and square wave voltammetry were used for the determination of riluzole levels in serum samples and pharmaceutical formulations. The limit of detections were found as 5.25 × 10^?7 M and 8.26 × 10^?8 M for glassy carbon electrode and 1.78 × 10^?7 M and 8.42 × 10^?8 M for boron-doped diamond electrodes, in serum samples, using differential pulse and square wave methods, respectively.     

Simultaneous Differential Pulse Voltammetric Determination of Ascorbic Acid and Caffeine in Pharmaceutical Formulations Using a Boron‐Doped Diamond Electrode

A cathodically pretreated boron‐doped diamond electrode was used for the simultaneous anodic determination of ascorbic acid (AA) and caffeine (CAF) by differential pulse voltammetry. Linear calibration curves (r=0.999) were obtained from 1.9×10^?5 to 2.1×10^?4 mol L^?1 for AA and from 9.7×10^?6 to 1.1×10^?4 mol L^?1 for CAF, with detection limits of 19 μmol L^?1 and 7.0 μmol L^?1, respectively. This method was successfully applied for the determination of AA and CAF in pharmaceutical formulations, with results equal to those obtained using a HPLC reference method.     

Simultaneous Determination of Caffeine and Acetylsalicylic Acid in Pharmaceutical Formulations Using a Boron‐Doped Diamond Film Electrode by Differential Pulse Voltammetry

This work presents a simple, fast and low‐cost method for simultaneous determination of acetylsalicylic acid (ASA), without alkaline hydrolysis and caffeine (CF) in pharmaceutical formulations using a boron‐doped diamond as the working electrode through differential pulse voltammetry. A good repeatability was reached for 20 measurements, with a low relative standard deviation of less than 1.0 %. The calibration curves presented a great linear correlation coefficient for both drugs (R=0.999) with a limit of detection of 1.6×10^?7 mol L^?1 for CF and 2.3×10^?7 mol L^?1 for ASA. The system was validated in comparison with the official method.     

Non‐Invasive Salivary Electrochemical Quantification of Paraquat Poisoning Using Boron Doped Diamond Electrode

The present work describes the first electrochemical method for quantifying paraquat herbicide poisoning in human saliva samples. Paraquat shows two couples of well‐defined peaks in aqueous solution using a boron doped diamond (BDD) electrode. By using square wave voltammetry (SWV) technique under optimum experimental conditions, a linear analytical curve was obtained for paraquat concentrations ranging from 0.800 to 167 µmol L^?1, with a detection limit of 70 nmol L^?1. This method was applied to quantify paraquat spikes in human saliva samples and in two different water samples (tap and river). The recovery values obtained ranged from 83.0 to 104 % and 99.1 to 105 %, respectively, which highlight the accuracy of the proposed method.     

Electrochemical Portable Method for on site Screening of Scopolamine in Beverage and Urine Samples

Scopolamine (SCP) is a psychoactive drug often added to beverages for recreational or abuse purposes (loss of memory and non‐consensual practices). In this work, a simple and portable method for fast in field screening of SCP in beverage (beer, coke, energy drink, sugarcane spirit, vodka, and whisky) and urine samples is presented. The proposed method is based on batch injection analysis with square wave voltammetric (BIA‐SWV) detection using boron‐doped diamond (BDD) as the working electrode. A voltammetric profile with accurate information on the presence or absence of SCP is obtained using a small sample volume (～50 μL) and a simple sample pretreatment step (dilution in supporting electrolyte). Around two hundred analyses are possible using the proposed system (injection of single sample plug – 120 μL) without the need of electrodes handling or supporting electrolyte exchange (friendly to point‐of‐care or on site screenings). The quantification of SCP in beverages is also possible using the proposed portable protocol, with a limit of detection of 0.18 μmol L^?1 and recovery values between 87 to 113 %.     

Simultaneous Differential Pulse Voltammetric Determination of Sulfamethoxazole and Trimethoprim on a Boron‐Doped Diamond Electrode

The performance of hydrogen‐ (HT) and oxygen‐terminated (OT) boron‐doped diamond (BDD) electrodes (electrochemically pretreated) on the simultaneous differential pulse voltammetric determination of sulfamethoxazole and trimethoprim in pharmaceutical products is presented. Under the optimum analytical experimental conditions, the HT‐BDD electrode presented two well‐defined oxidation peaks at 920 and 1100 mV vs. Ag/AgCl for sulfamethoxazole and trimethoprim, respectively. On the other hand, when the OT‐BDD electrode was used, the sulfamethoxazole oxidation current peak was decreased twenty fold. The calculated LOD values for sulfamethoxazole and trimethoprim using the HT‐BDD electrode were 3.65 μg L^?1 and 3.92 μg L^?1, respectively. The results obtained in the simultaneous determination of sulfamethoxazole and trimethoprim in three different commercial formulations were similar to those obtained using a standard HPLC method at 95% confidence level.     

A Boron Doped Diamond Electrode Modified with Nano‐carbon Black for the Sensitive Electrochemical Determination of Chlorogenic Acid

An electrochemical method was developed for the sensitive determination of chlorogenic acid using a boron doped diamond electrode (BDDE) modified with nano‐carbon black (nano‐CB). The active surface areas were found to be 0.059 and 0.146 cm² for the unmodified BDDE, and nano‐CB/BDDE, respectively. Compared with a BDDE, the nano‐CB/BDDE exhibited a well‐defined redox couple for chlorogenic acid. In addition, the plot of the peak current response changing from a square root to a linear dependence on scan rate is attributed to the transition from planar diffusion to surface behaviour. The anodic and cathodic peak separations (ΔE_p) were 97 mV and 14 mV at BDDE and nano‐CB/BDDE, respectively. The decrease in ΔE_p at the proposed electrode indicated that the process of chlorogenic acid was greatly accelerated. Square wave voltammetry (SWV) exhibited a dynamic range in which the current versus the concentration of chlorogenic acid were linear from 2.0×10^?8 to 2.0×10^?6 M with a LOD of 4.1×10^?9 M (based on 3S_b/m). The nano‐CB modified BDDE provided improved electrochemical behavior, high electrocatalytic activity, high sensitivity and good reproducibility.     

Electroanalytical Determination of N‐Nitrosamines in Aqueous Solution Using a Boron‐Doped Diamond Electrode

The electrochemical methods cyclic and square‐wave voltammetry were applied to develop an electroanalytical procedure for the determination of N‐nitrosamines (N‐nitrosopyrrolidine, N‐nitrosopiperidine and N‐nitrosodiethylamine) in aqueous solutions. Cyclic voltammetry was used to evaluate the electrochemical behaviors of N‐nitrosamines on boron‐doped diamond electrodes. It was observed an irreversible electrooxidation peak located in approximately 1.8 V (vs. Ag/AgCl) for both N‐nitrosamines. The optimal electrochemical response was obtained using the following square‐wave voltammetry parameters: f=250 Hz, E_sw=50 mV and E_s=2 mV using a Britton–Robinson buffer solution as electrolyte (pH 2). The detection and quantification limits determined for total N‐nitrosamines were 6.0×10^?8 and 2.0×10^?7 mol L^?1, respectively.