Determination of 2,4,6-trichloroanisole and guaiacol in cork stoppers by pressurised fluid extraction and gas chromatography-mass spectrometry

This paper describes the development of an analytical method consisting of pressurised fluid extraction (PFE) and gas chromatography-mass spectrometry (GC-MS) using experimental designs to determine two volatile compounds in naturally-tainted cork stoppers. The target analytes, 2,4,6-trichloroanisole (2,4,6-TCA) and guaiacol, are involved in the cork taint of wine. First, a Plackett-Burman experimental design was carried out in order to determine the significant experimental parameters affecting the PFE process, and then a central composite design was used to optimise these significant parameters. Once the method had been optimised, the influence of the number of extraction cycles was studied. The method was applied to determine the concentration of 2,4,6-TCA and guaiacol in three cork samples, and the results were compared with the ones obtained by multiple headspace-solid-phase microextraction (MHS-SPME) and by Soxhlet extraction.     

Optimisation of a headspace solid-phase microextraction with on-fiber derivatisation method for the direct determination of haloanisoles and halophenols in wine

A solid-phase microextraction (SPME) procedure for the determination of four haloanisoles (2,4,6-trichloroanisole, 2,3,4,6-tetrachloroanisole, pentachloroanisole and 2,4,6-tribromoanisole), as well as their precursor halophenols (2,4,6-trichlorophenol, 2,3,4,6-tetrachlorophenol, pentachlorophenol and 2,4,6-tribromophenol), involved in the presence of cork taint in wine, was developed. Firstly, analytes were concentrated on a SPME fiber, and then halophenols were derivatised using N-methyl-N-trimethylsilyltrifluoroacetamide (MSTFA). The compounds were desorbed for 5 min in the gas chromatography injector port and then determined with an electron capture detector. The influence of different parameters on the efficiency of extraction (volume of sample, type of fibre coating and time) and derivatisation (time, temperature and volume of MSTFA) steps was evaluated. Polyacrylate (PA) was selected as the extraction fiber, optimised parameters for SPME were 10 ml of wine, temperature 70 degrees C and extraction time 60 min. The optimal conditions identified for the derivatisation step were temperature 25 degrees C, reagent volume 50 microl and extraction time 25 min. Under optimal conditions, the proposed method showed satisfactory linearity, precision and detection limits. The method was applied successfully to the analysis of red wine samples. To our knowledge, this is the first time that headspace (HS) SPME combined with on-fiber derivatisation has been applied to determine cork taint responsible compounds in wine.     

Multiple headspace solid-phase microextraction for eliminating matrix effect in the simultaneous determination of haloanisoles and volatile phenols in wines

This paper proposes a multiple headspace solid-phase microextraction (MHS-SPME) method coupled to gas chromatography-tandem mass spectrometry detection (GC/MS/MS) for the simultaneous determination of 2,4,6-trichloroanisole, 2,3,4,6-tetrachloroanisole, pentachloroanisole, 2,4,6-tribromoanisole, 4-ethylphenol, 4-ethylguaiacol, 4-vinylphenol and 4-vinylguaiacol in wines. These compounds are involved in the presence of "cork taint" and Brett character in wines. The MHS-SPME method is a modification of SPME developed for quantitative analysis that avoids possible matrix effects based on an exhaustive analyte extraction from the sample. After demonstrating the existence of matrix effect in the analysis of the target compounds by HS-SPME with a divinylbenzene/Carboxen/polydimethylsiloxane (DVB/CAR/PDMS) fibre, the MHS-SPME method was developed and validated. The proposed method showed satisfactory linearity, precision and detection limits, all below the odour detection thresholds of the compounds in wine matrices. Good recoveries were observed for all compounds, always above 90%, and the repeatability obtained was considered acceptable, ranging between 2 and 11%. After checking the applicability of the method by comparing the results recorded with those obtained with the standard addition method, the method was applied successfully to the analysis of wine samples. To our knowledge, this is the first time that MHS-SPME combined with GC/MS/MS has been applied to simultaneously determine haloanisoles and volatile phenols in wine.     

Direct determination of 2,4,6-tricholoroanisole in wines by single-drop ionic liquid microextraction coupled with multicapillary column separation and ion mobility spectrometry detection

This article evaluates the capability of single drop ionic liquid microextraction coupled with multicapillary column (MCC) and ion mobility spectrometry (IMS) for the determination of 2,4,6-trichloroanisole (2,4,6-TCA) in wines. The proposed methodology permits the direct analysis of the samples without any additional treatment other than dilution. This is achieved thanks to the selectivity provided by the ionic liquid selected as extractant, 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)-imide, as well as the response of the analyte in the IMS working in negative ionization mode. Moreover, the multicapillary column avoids the interference of ethanol in the ion mobility spectra. The analysis of the sample takes ca. 35 min to be completed. The limit of detection was low as 0.01 ng L(-1) using 2 mL of wine sample. Different calibration curves were constructed using aqueous standards, red and white wines, being the signals comparable, with an RSD similar to the method variability. Finally, a set of samples of different nature and packed in different containers were analysed. It was found than those with cork stoppers presented the highest concentration of 2,4,6-TCA.     

Relationship between sensory and instrumental analysis of 2,4,6-trichloroanisole in wine and cork stoppers

The effect of different corks stoppers on the sensory and instrumental determination of 2,4,6-trichloroanisole (TCA) was studied in wine and cork. A relationship between both measurements was also established.Four types of cork were used to seal white wine bottles for 8 months. The stoppers were from different raw material: a high quality commercial batch (C), slabs with yellow stain (YS) and slabs with a high musty and mouldy taint (T). Spiked samples (S) were prepared from C batch by injecting 1002 ng of TCA into the cork stoppers.TCA was determined by gas chromatography with electron capture detection after headspace solid phase microextraction in bottled wine (12 per group) and after extraction with pentane in the case of corks (six per group). Seven semi-trained assessors evaluated the different samples using a ranking test in 12 and six sessions for wine and cork stoppers, respectively.Wines and corks from S samples showed the highest TCA values in both sensory and instrumental measurements, the lowest values being for C samples. YS and T corks had intermediate values, although in general TCA concentration was higher in T. A slight tendency to increase the TCA content in stoppers with yellow stain compared to C samples was observed in wine. A high correlation coefficient (r=0.82) was found between sensory and instrumental analysis for wine, whereas this coefficient was much lower (r=0.56) for cork stoppers. Some hypotheses are given in order to explain these differences.     

Purge-and-trap preconcentration system coupled to capillary gas chromatography with atomic emission detection for 2,4,6-trichloroanisole determination in cork stoppers and wines

A method based on solvent extraction and purge-and-trap capillary gas chromatography with atomic emission detection (PT-GC-AED) for the determination of 2,4,6-trichloroanisole (TCA) in wines and cork stoppers was optimized and evaluated. TCA was previously extracted from the samples in pentane and the preconcentrated extract was reconstituted in water before being injected into the chromatograph by means of the PT system. Element-specific detection and quantification was carried out by monitoring the chlorine (479 nm) emission line. Two different calibration graphs were used to quantify TCA in the cork or the wine samples, owing to the interference produced by the ethanol content in the wines. Detection limits of 25 pg g(-1) and 5 ng l(-1) were obtained for corks and wines, respectively. The method provided recoveries from spiked samples ranging from 88.5 to 102.3%, confirming the reliability of the procedure and its suitability for routine monitoring.     

Non-destructive method to determine halophenols and haloanisoles in cork stoppers by headspace sorptive extraction

The new solvent-free technique called headspace sorptive extraction (HSSE) was used to determine 2,4,6-trichlorophenol, 2,3,4,6-tetrachlorophenol, 2,4,6-trichloroanisole, 2,3,4,6-tetrachloroanisole, 2,4,6-tribromoanisole, pentachloroanisole in cork stoppers, without grinding them, as these may be responsible for the cork taint off-flavour in wine. The best HSSE sorption kinetics for the target analytes were obtained after submitting the spiked corks to 100 degrees C for 1h, followed by a 30 min stabilization time at room temperature. The stir bar was desorbed in a thermal desorption system coupled to a gas chromatograph-mass spectrometer. The method proposed showed good linearity over the concentration range tested, 1-70 ngg(-1), and correlation coefficients ranged from 0.90 to 0.99 for all the analytes. The reproducibility and repeatability of the method were estimated between 4.91 and 12.67%. The effect of the different cork matrixes on the extraction recovery of the target compounds was studied, with the natural corks showing the higher recovery percentage in relation to agglomerate ones.     

Development of a dispersive liquid-liquid microextraction method for the simultaneous determination of the main compounds causing cork taint and Brett character in wines using gas chromatography-tandem mass spectrometry

A novel dispersive liquid-liquid microextraction (DLLME) method, coupled to gas chromatography-tandem mass spectrometry (GC-MS/MS), was developed for simultaneously determining the main compounds responsible for cork taint (2,4,6-trichloranisole (TCA), 2,3,4,6-tetrachloroanisole (TeCA), 2,4,6-tribromoanisole (TBA) and pentachloranisole (PCA)) and Brett character (4-ethylguaiacol (EG), 4-ethylphenol (EP), 4-vinylguaiacol (VG) and 4-vinylphenol (VP)) in wines. Optimisation of DLLME procedure was performed by evaluating the type of disperser and extraction solvents and the temperature and salt addition effects. The volumes of disperser and extraction solvents were also optimised by means of a central composite design combined with desirability functions. Under optimum conditions, 5 mL of wine were extracted with an extraction mixture consisting of 1.43 mL of acetone, and 173 μL of chloroform at room temperature. The analytical characteristics of the method were evaluated. Satisfactory linearity (with correlation coefficients over 0.992), repeatability (below 11.6%) and between-days precision (below 11.0%) were obtained for all target analytes. Detection limits attained were at similar levels or even lower than the olfactory threshold of the studied compounds. Finally, the developed method was successfully applied to the analysis of wine samples. To our knowledge, this is the first time that DLLME has been applied to simultaneously determine the compounds responsible for cork taint and Brett character in wine.     

Development of a cellular biosensor for the detection of 2,4,6-trichloroanisole (TCA)

2,4,6-trichloroanisole (TCA) is a microbial metabolite formed from chlorophenols through the activity of several natural fungal strains present on the cork oak bark. TCA is the primary compound responsible for the mousty/mould off-odour known as “cork taint” present in cork stoppers, wine, water and alcoholic beverages. Chromatographic and electrochemical methods are currently used for the determination of TCA, however its detection at low concentrations remains a technical challenge. The aim of this study was the development of a rapid novel biosensor system based on the Bioelectric Recognition Assay (BERA). The sensor measured the electric response of cultured membrane-engineered fibroblast cells suspended in an alginate gel matrix due to the change of their membrane potential in the presence of the analyte. Membrane-engineered cells were prepared by osmotic insertion of 0.5 μg/l of specific TCA antibodies into the membrane of the cells. The BERA-based sensor was able to detect TCA in a few minutes (3-5 min) at extremely low concentrations (10⁻¹ ppt), thus demonstrating higher sensitivity than the human sensory threshold. In addition, the assay was quite selective against other haloanisoles and halophenols structurally related to or co-occurring with TCA. Finally the sensor was tested against real white wine samples from cork soaks. At this real test, the BERA sensor was able to detect TCA from cork soaks rapidly (3-5 min) at very low concentrations (1.02-12 ng/l), covering the whole range for the detection threshold for wines (1.4-10 ng/l). Therefore, this novel biosensor offers new perspectives for ultra-rapid, ultra-sensitive and low-cost monitoring of TCA presence in cork and wine and possibly also other food commodities.     

Multiple headspace-solid-phase microextraction: An application to quantification of mushroom volatiles

Multiple headspace-solid phase microextraction (MHS-SPME) followed by gas chromatography/mass spectrometry (GC–MS) and flame ionization detection (GC–FID) was applied to the identification and quantification of volatiles released by the mushroom Agaricus bisporus, also known as champignon. MHS-SPME allows to perform quantitative analysis of volatiles from solid matrices, free of matrix interferences. Samples analyzed were fresh mushrooms (chopped and homogenized) and mushroom-containing food dressings. 1-Octen-3-ol, 3-octanol, 3-octanone, 1-octen-3-one and benzaldehyde were common constituents of the samples analyzed. Method performance has been tested through the evaluation of limit of detection (LoD, range 0.033–0.078 ng), limit of quantification (LoQ, range 0.111–0.259 ng) and analyte recovery (92.3–108.5%). The results obtained showed quantitative differences among the samples, which can be attributed to critical factors, such as the degree of cell damage upon sample preparation, that are here discussed. Considerations on the mushrooms biochemistry and on the basic principles of MHS analysis are also presented.     

Development of solid-phase extraction and solid-phase microextraction methods for the determination of chlorophenols in cork macerate and wine samples

Tri-, tetra- and pentachlorophenol (TCP, TeCP and PCP) can be considered the precursors in the formation of corresponding chloroanisoles, known to be powerful odorants in corks and wine. Determining the presence of these chlorophenolic compounds in cork soaking solutions (ethanol/water mixtures, 12% (v/v) ethanol used for cork quality control testing), or in wine can be achieved by acetylation/gas chromatography electron-capture detection. In order to reach the required sensitivity, a previous preconcentration step is necessary. Solid-phase extraction (SPE) and headspace solid-phase microextraction (HS-SPME) have given good results for the preconcentration of TCP, TeCP and PCP in such matrices. The use of Oasis HLB cartridges gives acceptable recoveries for the three compounds when different volumes (50-250 mL) of cork macerate with concentrations ranging from 20 to 150 ng/L are processed. Preconcentration based on HS-SPME has also been optimised with a 100 microm polydimethylsiloxane fibre and in situ derivatization. The HS-SPME method allows chlorophenols in a cork soaking solution and in wine to be determined with a limit of detection of 1 ng/L for each compound (in cork macerate) and a repeatability of around 0.5%-5% (n=8) for a concentration level of 30 ng/L.     

Reduction of the 2,4,6-trichloroanisole content in cork stoppers using gamma radiation

This work demonstrates that it is possible to eliminate or transform 2,4,6-trichloroanisole (2,4,6-TCA) in cork stoppers, using gamma radiation transforming it in molecular residues which do not have the same organoleptic/odour characteristics. This process when applied to packed cork stoppers ready to use, inside their sealed packages, avoiding later contamination, assures the elimination/reduction of the problem, which is an enormous advantage over the other processes. Studies were carried out with cork stoppers naturally contaminated using radiation doses from 15 to 400 kGy. The results showed elimination/reduction efficiencies of 2,4,6-TCA higher than 90%.     

Analysis for chloroanisoles and chlorophenols in cork by stir bar sorptive extraction and gas chromatography–mass spectrometry

A complete methodology for the determination of chloroanisoles and chlorophenols in cork material is proposed. The determination is accomplished by means of a previous liquid–solid extraction followed by stir bar sorptive extraction (SBSE) coupled to gas chromatography–mass spectrometry (GC–MS). Two different liquid–solid extraction experiments were conducted and eight compounds considered (2,6-dichloroanisole, 2,4-dichloroanisole, 2,4,6-trichloroanisole, 2,4,6-trichlorophenol, 2,3,4,6-tetrachloroanisole, 2,3,4,6-tetrachlorophenol, pentachloroanisole and pentachlorophenol). From the results obtained we can conclude that high volume extraction extending extraction time up to 24 h is the best choice if we have to release compounds from the inner surfaces of cork stoppers. Recovery percentages ranged from 51% for pentachloroanisole to 81% for 2,4-dichloroanisole. This method allows the determination of an array of compounds involved in cork taint at very low levels from 1.2 ng g⁻¹ for 2,4,6-tricholoroanisole to 23.03 ng g⁻¹ for 2,3,4,6-tetrachlorophenol.     

Optimisation of a microwave-assisted extraction method for the simultaneous determination of haloanisoles and halophenols in cork stoppers

This study presents a method based on the use of microwave-assisted extraction (MAE) for the quantitative analysis of 2,4,6-trichloroanisole (TCA), 2,3,4,6-tetrachloroanisole (TeCA), pentachloroanisole (PCA), 2,4,6-tribromoanisole (TBA), 2,4,6-trichlorophenol (TCP), 2,3,4,6-tetrachlorophenol (TeCP), pentachlorophenol (PCP) and 2,4,6-tribromophenol (TBP) in cork stoppers. The influential parameters of the MAE procedure (extraction time, temperature and solvent volume) were optimised using a central composite experimental design combined with desirability functions. The optimal conditions identified were temperature 170 degrees C, solvent volume 35 mL and extraction time 90 min. MAE extracts were concentrated and derivatised prior to separation and quantification by gas chromatography with electron capture detection. To evaluate the applicability of the proposed MAE method, recovery results were compared with those obtained with the Soxhlet extraction method; the results were similar with both extraction methods. The new method was also satisfactorily applied to real cork stopper samples.     

Multiple solid-phase microextraction in a non-equilibrium situation. Application in quantitative analysis of chlorophenols and chloroanisoles related to cork taint in wine

Multiple HS-solid-phase microextraction (MHS-SPME) is a modification of SPME developed for quantitative analysis that avoids possible matrix effects based on an exhaustive analyte extraction from the sample. In this paper, the theory of this process associated with a non-equilibrium situation has been presented. The application of an optimised HS-SPME-based method in the analysis of chloroanisoles and chlorophenols, previously acetylated, associated with the occurrence of cork taint in different red, white and rosé wine samples, has revealed the existence of matrix effects. This fact determines the choice of standard addition as the adequate technique for the quantification of these compounds in real samples. MHS-SPME is proposed as a good alternative technique with respect to HS-SPME because it avoids matrix effects, simplifies the quantification of these compounds in real samples and reduces analysis time, providing sensitivity below chloroanisole sensory threshold with acceptable precision.     

Optimisation of a pressurised liquid extraction method for haloanisoles in cork stoppers

Cork taint is a musty off-flavour in wines mainly caused by 2,4,6-trichloroanisole, but other haloanisoles can contribute. In this work, a method for the extraction of 2,4,6-trichloroanisole, 2,4,6-tribromoanisole and 2,6-dichloroanisole has been developed. The procedure involves the extraction of the haloanisoles from cork by pressurised liquid extraction and the analysis of the extracts by both GC-μECD and GC-MS-MS. A central composite design was used to investigate the dependence of the recoveries of the analytes on the temperature, percentage pentane-diethyl ether ratio and the extraction time. Experimental data were then processed by using the multiple regression analysis in order to calculate a mathematical model representing the relationship between factors and responses and to determine the best experimental conditions for PLE method. These conditions corresponded to a temperature of 176 °C, an extraction time between 2.8 and 4 min and an 80:20 pentane:diethyl ether ratio.     

Application of robust NiTi-ZrO2-PEG SPME fiber in the determination of haloanisoles in cork stopper samples

In this study, a novel solid-phase microextraction (SPME) fiber obtained using sol-gel technology was applied in the determination of off-flavor compounds (2,4,6-trichloroanisole (TCA), 2,4,6-tribromoanisole (TBA) and pentachloroanisole (PCA)) present in cork stopper samples. A NiTi alloy previously electrodeposited with zirconium oxide was used as the substrate for a poly(ethylene glycol) (PEG) coating. Scanning electronic microscopy showed good uniformity of the coating and allowed the coating thickness to be estimated as around 17 micarom. The optimization of the main parameters influencing the extraction efficiency, such as cork sample mass, sodium chloride mass, extraction temperature and extraction time were optimized using a full factorial design, followed by a Doehlert design. The optimum conditions were: 20 min of extraction at 70 degrees C using 60 mg of the cork sample and 10 mL of water saturated with sodium chloride in a 20 mL amber vial with constant magnetic stirring. Satisfactory detection limits between 2.5 and 5.1 ng g(-1) were obtained, as well as good precision (R.S.D. in the range of 5.8-12.0%). Recovery tests were performed on three different cork samples, and values between 83 and 119% were obtained. The proposed SPME fiber was compared with commercially available fibers and good results were achieved, demonstrating its applicability.     

Optimisation of the derivatisation reaction and subsequent headspace solid-phase microextraction method for the direct determination of chlorophenols in red wine

An acetylation reaction for the derivatisation of the three chlorophenols involved in cork taint was optimised using a Doehlert design for direct application in wine samples. In this first step, the optimum reaction pH, by adding different amounts of KHCO3, and the required quantity of derivatisation reagent were fixed. Then a series of parameters relevant for the headspace solid-phase microextraction process, such as desorption conditions, salt addition and agitation sample were evaluated. A simultaneous study of the type of fibre and extraction temperature was performed at five levels and based on the results obtained the rest of factors (sample volume and exposition time) that could potentially affect the extraction yields were optimised by a central composite design. According to the validation of the method, we propose here, to our knowledge, the first application of solid-phase microextraction for the direct analysis of chlorophenols in red wine samples.     

Rapid headspace solid-phase microextraction/gas chromatographic/mass spectrometric assay for the quantitative determination of some of the main odorants causing off-flavours in wine

In this study we present a rapid and simultaneous assay method using headspace (HS) solid-phase microextraction (SPME)/gas chromatography (GC)/electron impact (EI) mass spectrometry (MS) (selected ion monitoring) for contaminants causing the principal organoleptic defects of wine (2,4,6-trichloroanisole, 2,3,4,6-tetrachloroanisole, pentachloroanisole, 2,4,6-tribromoanisole, 1-octen-3-ol, geosmin, 2-methylisoborneol, 3-isopropyl-2-methoxypyrazine, fenchol, fenchone, 2-methoxy-3,5-dimethylpyrazine, 4-ethylphenol, 4-ethylguaiacol, 4-vinylphenol, 4-vinylguaiacol, 3-isobutyl-2-methoxypyrazine, guaiacol and ethyl acetate). The method was validated according to protocols NF ISO 5725-1, 2 and NF V03-110. Its characteristics (limit of detection (LOD), limit of quantification (LOQ), uncertainties) were determined after having optimised the SPME parameters. The target contaminants were quantified in the wines below their threshold of perception with a satisfactory relative standard deviation for all the analytes except ethyl acetate (RSD=36%); for that, the assay method permits clear differentiation of the wines that are at risk of presenting an acescent character, i.e. containing more than 120mgL(-1) ethyl acetate. The target volatile and odorous substances were determined at concentrations significantly below their threshold of perception in a hydroalcoholic context and their threshold of recovery in wines.     

Evaluation of dispersive liquid-liquid microextraction for the simultaneous determination of chlorophenols and haloanisoles in wines and cork stoppers using gas chromatography-mass spectrometry

Dispersive liquid-liquid microextraction (DLLME) coupled with gas chromatography-mass spectrometry (GC-MS) was evaluated for the simultaneous determination of five chlorophenols and seven haloanisoles in wines and cork stoppers. Parameters, such as the nature and volume of the extracting and disperser solvents, extraction time, salt addition, centrifugation time and sample volume or mass, affecting the DLLME were carefully optimized to extract and preconcentrate chlorophenols, in the form of their acetylated derivatives, and haloanisoles. In this extraction method, 1mL of acetone (disperser solvent) containing 30μL of carbon tetrachloride (extraction solvent) was rapidly injected by a syringe into 5mL of sample solution containing 200μL of acetic anhydride (derivatizing reagent) and 0.5mL of phosphate buffer solution, thereby forming a cloudy solution. After extraction, phase separation was performed by centrifugation, and a volume of 4μL of the sedimented phase was analyzed by GC-MS. The wine samples were directly used for the DLLME extraction (red wines required a 1:1 dilution with water). For cork samples, the target analytes were first extracted with pentane, the solvent was evaporated and the residue reconstituted with acetone before DLLME. The use of an internal standard (2,4-dibromoanisole) notably improved the repeatability of the procedure. Under the optimized conditions, detection limits ranged from 0.004 to 0.108ngmL(-1) in wine samples (24-220pgg(-1) in corks), depending on the compound and the sample analyzed. The enrichment factors for haloanisoles were in the 380-700-fold range.