Stable nanosecond pulse generation from a graphene-based passively Q-switched Yb-doped fiber laser

We demonstrate stable 70?ns pulse generation from a Yb-doped fiber laser passively Q-switched by a graphene-based saturable absorber mirror in a short linear cavity. The maximum output power was 12?mW and the highest single pulse energy was 46?nJ. The repetition rate of the fiber laser can be widely tuned from 140 to 257?kHz along with the increase of the pump power. To the best of our knowledge, this is the first report for passively Q-switched sub-100-ns pulse operation of a graphene-based saturable absorber in a Yb-doped fiber laser.     

High-energy soliton pulse generation with a passively mode-locked Er/Yb-doped multifilament-core fiber laser

We report the generation of high-energy short pulses from a mode-locked erbium/ytterbium-doped large-mode-area multifilament-core fiber laser operating in the purely anomalous dispersion regime. The self-starting fiber laser emits 400 mW of average output power at a pulse repetition rate of 44 MHz, corresponding to a pulse energy of 9.1 nJ. The laser produces near transform-limited output pulses with pulse duration of 1.6 ps, corresponding to 5 kW peak power. This new type of low-nonlinearity fibers demonstrates the power and energy scaling potential of fiber-based short pulse lasers in the eye-safe region.     

High-energy Q-switched fiber laser based on the side-pumped active fiber

A relatively simple fiber-laser system that is based on a dual fiber, is pumped by a single CW source with an output power of 12 W (976 nm), and provides an output pulse energy of up to 110 μJ at a wavelength of 1080 nm is demonstrated for the first time. The output-pulse repetition rate and duration can be varied in the ranges 45–140 kHz and 0.28–1.80 μs, respectively, with a variation in the pumping power. The maximum output power is 5 W. It is demonstrated that the generation instability observed at an output power of greater than 5 W gives rise to giant pulses that can induce the supercontinuum generation in the range 530–1750 nm in a relatively short microstructured fiber.     

Q-switched ytterbium doped carbon nanotubes fiber laser using multi-walled saturable absorber

A Q-switched ytterbium-doped fiber laser （YDFL） is proposed and demonstrated using a newly developed multi-walled carbon nanotubes polyethylene oxide （MWCNTs-PEO） film as a passive saturable absorber （SA）. The saturable absorber is prepared by mixing the MWCNTs homogeneous solution into a dilute PEO polymer solution before it is left to dry at room temperature to produce thin film. Then the film is sandwiched between two FC/PC fiber connectors and integrated into the laser cavity for Q-switching pulse generation. The laser generates a stable pulse operating at wavelength of 1060.2 nm with a threshold pump power of 53.43 mW. The YDFL generates a stable pulse train with repetition rates ranging from 7.92 to 24.27 kHz by varying 980-nm pump power from 53.42 to 65.72 mW. At 59.55-mW pump power, the lowest pulse width and the highest pulse energy are obtained at 12.18 μs and 143.5 n J, respectively.     

Q-switched ytterbium doped fiber laser using multi-walled carbon nanotubes saturable absorber

A Q-switched ytterbium-doped fiber laser(YDFL)is proposed and demonstrated using a newly developed multi-walled carbon nanotubes polyethylene oxide(MWCNTs-PEO)film as a passive saturable absorber(SA).The saturable absorber is prepared by mixing the MWCNTs homogeneous solution into a dilute PEO polymer solution before it is left to dry at room temperature to produce thin film.Then the film is sandwiched between two FC/PC fiber connectors and integrated into the laser cavity for Q-switching pulse generation.The laser generates a stable pulse operating at wavelength of 1060.2 nm with a threshold pump power of 53.43 mW.The YDFL generates a stable pulse train with repetition rates ranging from7.92 to 24.27 kHz by varying 980-nm pump power from 53.42 to 65.72 mW.At 59.55-mW pump power,the lowest pulse width and the highest pulse energy are obtained at 12.18μs and 143.5 nJ,respectively.     

High-energy single-transverse-mode Q-switched fiber laser based on a multimode large-mode-area erbium-doped fiber

We demonstrate that appropriately designed doped multimode fibers provide robust single-mode output when used within a fiber laser cavity. Using a novel large-mode-area fiber, we demonstrate what we believe to be record single-mode (M(2) <1.2) pulse energies of >0.5 mJ from a Q -switched fiber laser and even higher pulse energies (as high as 0.85 mJ) with slightly compromised spatial-mode quality (M(2)<2.0) . This approach offers significant scope for extending the range of single-mode output powers and energies that are achievable from fiber-laser-amplifier systems.     

超长腔碳纳米管锁模多波长掺镱光纤激光器

报道了一种超长腔碳纳米管锁模多波长掺镱光纤激光器, 光纤激光器的总长度为1021.2 m. 实验得到了噪声型孤子和孤子雨两种类型的多波长锁模脉冲, 重复频率均为199.8 kHz. 孤子雨具有更高的输出功率和单脉冲能量, 分别为40.3 mW和201.5 nJ, 对应的脉冲宽度为102.5 ns.     

High-energy, high-power ytterbium-doped Q-switched fiber laser

We report on a Q -switched, cladding-pumped, ytterbium-doped large-mode-area fiber laser operating at 1090 nm that is capable of generating 2.3 mJ of output pulse energy at a 500-Hz repetition rate and more than 5 W of average output power at higher repetition rates in a high-brightness beam (M(2) = 3) . Using a similar fiber with a smaller core, we generated >0.5-mJ pulses in a diffraction-limited beam. Our results represent a threefold increase in pulse energy over previously published values for Q-switched fiber lasers and firmly establish fiber lasers as compact, multiwatt, multimillijoule pulse sources with large scope for both industrial and scientific applications.     

High-power all-normal-dispersion femtosecond pulse generation from a Yb-doped large-mode-area microstructure fiber laser

We report on an all-normal-dispersion mode-locked fiber laser based on a large-mode-area Yb-doped microstructure fiber and using a high nonlinear modulation depth semiconductor saturable absorber mirror. The laser delivers 3.3 W of average output power with positively chirped 5.5 ps pulses at a center wavelength of 1033 nm. The pulse repetition rate is 46.4 MHz, which results in an energy per pulse of 71 nJ. These pulses are extracavity dechirped down to 516 fs by using bulk gratings. The average power of the dechirped pulses is 2.3 W, which corresponds to a peak power of more than 96 kW.     

Q-switched fiber laser using carbon platinum saturable absorber on side-polished fiber

A 1550 nm Q-switched fiber laser using a carbon platinum saturable absorber deposited on side-polished fiber(SPF) is proposed and demonstrated. The SPF is approximately 2 mm with a polarization-dependent loss(PDL)of 0.4 dB and an insertion loss of 2.5 dB. A stable Q-switched output spectrum is obtained at 1559.34 nm with a peak power of ~6 mW, a pulse width of 1.02 μs, pulse energy of 5.8 nJ, average output power of 0.76 mW, and a repetition rate of 131.6 kHz taken at a pump power of 230.0 mW. A signal-to-noise ratio of 49.62 d B indicates that the Q-switched pulse is highly stable.     

Ultrashort pulse generation using fiber FM laser

Ultrashort optical pulse generation using a fiber FM laser is presented and analyzed in detail. Fiber FM laser operation is realized using a fiber ring with an internal phase modulator and an erbium-doped fiber amplifier. To compress FM laser pulses, an external dispersive single-mode fiber is employed. Furthermore, by external intensity modulation, the pulse background is removed. The background ratio of the generated ultrashort pulse is calculated and compared with the experimental results. The experimental results show an output optical pulse width of 1.77 ps and a spectral bandwidth of 0.5 THz.     

Actively Q-switched mode-locked Yb-doped fiber laser with high mode-locking contrast

Reliable Q-switched and mode-locked operation of Yb-doped fiber lasers is investigated by employing an acousto-optic modulator (AOM) in a linear cavity configuration. The widths and shapes of the Q-switched envelopes mainly depend on the external modulation frequency of the AOM and near symmetric Q-switched pulses can be generated. Within the Q-switched envelopes, harmonic mode-locked pulses with near 100% modulation depth at the 40 MHz repetition rate are experimentally observed.     

11-mJ pulse energy wideband Yb-doped fiber laser

We report a wide bandwidth (Δλ=8 nm) optical pulsed MOPA (master oscillator power amplifier) source emitting 11.23 mJ pulses (1.25 MW peak power) in the wavelength centered at (λ=1064 nm). Pulse duration and repetition rate were 9 ns and from 10 Hz to 100 Hz, respectively. In order to suppress amplified spontaneous emission (ASE), multi-stage pulse pump technology is applied. And the large core diameter (90 μm) and wide bandwidth ensures the high peak power and energy output.     

Millijoule pulse energy Q-switched short-length fiber laser

We report on a Q-switched short-length fiber laser producing 100 W of average output power at 100 kHz repetition rate and pulse durations as short as 17 ns. Up to 2 mJ of energy and sub-10-ns pulse duration are extracted at lower repetition rates. This performance is obtained by employing a rod-type ytterbium-doped photonic crystal fiber with a 70 microm core as gain medium, allowing for very short pulse durations, high energy storage, and emission of a single-transverse-mode beam.     

High-energy femtosecond Yb-doped fiber laser operating in the anomalous dispersion regime

We report on high-energy ultrashort pulse generation from a passively mode-locked ytterbium-doped large-mode-area photonic crystal fiber oscillator operating in the anomalous dispersion regime. In the single-pulse regime, the laser directly generates 880 mW of average power of sub-500 fs pulses at a repetition rate of 53.33 MHz, corresponding to a pulse energy of 16.5 nJ. Stable and self-starting operation is obtained by adapting the spot size at the saturable absorber mirror to the pulse evolution in the low-nonlinearity fiber. The approach presented demonstrates the scaling potential of fiber based short pulse oscillators towards the microJ-level.     

All-fiber actively Q-switched Yb-doped laser

An all-fiber actively Q-switched Yb-doped laser is presented. Q-switching is performed by modulating a fiber Bragg grating via a magnetostrictive rod which is fixed to the fiber at the position of the grating. By exposing the rod to a changing magnetic field, the rod is stretched and relaxed causing the Bragg wavelength of the grating to shift and thereby changes the Q-factor of the cavity. Using Yb-doped fiber, pulses at 1052 nm are obtained at repetition rates from 1 to 200 kHz. At 75 kHz, 0.5 μJ pulses with peak powers of 3 W can be produced when 180 mW of pump power is applied. To the knowledge of the authors, this is the first all-fiber actively Q-switched Yb-doped laser presented to date.     

All-optical trion generation in single-walled carbon nanotubes

We present evidence of all-optical trion generation and emission in pristine single-walled carbon nanotubes (SWCNTs). Luminescence spectra, recorded on individual SWCNTs over a large cw excitation intensity range, show trion emission peaks redshifted with respect to the bright exciton peak. Clear chirality dependence is observed for 22 separate SWCNT species, allowing for determination of electron-hole exchange interaction and trion binding energy contributions. Luminescence data together with ultrafast pump-probe experiments on chirality-sorted bulk samples suggest that exciton-exciton annihilation processes generate dissociated carriers that allow for trion creation upon a subsequent photon absorption event.     

High-energy and high-peak-power nanosecond pulse generation with beam quality control in 200-microm core highly multimode Yb-doped fiber amplifiers

We explored high-energy and high-peak-power pulse generation in large-core multimode fiber amplifiers, achieving what is to our knowledge the highest reported energies, up to 82 mJ for 500-ns pulses, 27 mJ for 50-ns pulses, and 2.4-MW peak power for 4-ns pulses at 1064 nm, using 200-microm-diameter and 0.062-N.A. core Yb-doped double-clad fiber amplifiers. The highly multimode nature of the fiber core was mitigated by use of a coiling-induced mode-filtering effect to yield a significant improvement in output-beam quality from M2 = 25 from an uncoiled fiber to M2 = 6.5 from a properly coiled fiber, with the corresponding reduction in number of propagating transverse modes from > or = 200 to < or = 20.     

可调脉冲宽度的调Q掺铥双包层光纤激光器

在激光器输出平均功率一定的情况下,峰值功率主要取决于调制频率和脉冲宽度。这使得脉冲宽度的调节具有一定的实际应用价值。对调Q掺铥双包层光纤激光器进行研究,首先确定了激光器的最佳输出透过率,在65%最佳透过率时,得到2 m激光的输出功率3.9 W,斜率效率为31%。外接一个信号发生器,信号门宽从12 s变化到18 s,并测量了调制频率分别在30 kHz、40 kHz和50 kHz时输出脉冲宽度的变化情况,得到了555.6 W的最高峰值功率,实现了脉冲宽度从163.4 ns到207.9 ns的变化。实验情况证实了用外接信号发生器能有效控制激光器的输出脉冲宽度。     

Q-switched Yb-doped nonlinear microstructured fiber laser for the emission of broadband spectrum

We report on an innovative configuration of a supercontinuum laser based on an Yb-doped nonlinear microstructured fiber. Due to this particular fiber design combining amplification and nonlinear properties, a wideband output spectrum is generated in the fiber under the Q-switched regime. By exploiting stimulated Brillouin scattering, high peak power pulses are achieved and contribute to a spectral broadening due to a nonlinear wavelength conversion process. Both infrared (1000-1200 nm) and visible (650-750 nm) spectra are generated with an average power of 200 mW.