氧化石墨烯被动锁模掺镱光纤激光器多脉冲现象的实验研究

利用氧化石墨烯作为可饱和吸收体,在被动锁模全正常色散掺镱光纤激光器中研究了多脉冲的现象,在同一抽运功率不同偏振态下,实验获得了矩形脉冲谐波锁模、耗散孤子谐波锁模、准谐波锁模,脉冲峰值周期性调制,脉冲簇、脉冲束、混沌多重脉冲的多脉冲现象,插入激光腔内的2nm窄带滤波器具有限制增益带宽、对脉冲塑形、诱导多脉冲产生的作用,调节偏振控制器相当于改变腔内增益,是实现不同类型多脉冲现象的主要原因,本实验研究有利于加深对多脉冲动力学行为在正常色散区域氧化石墨烯锁模掺镱光纤激光器中的理解。     

High-power all-normal-dispersion femtosecond pulse generation from a Yb-doped large-mode-area microstructure fiber laser

We report on an all-normal-dispersion mode-locked fiber laser based on a large-mode-area Yb-doped microstructure fiber and using a high nonlinear modulation depth semiconductor saturable absorber mirror. The laser delivers 3.3 W of average output power with positively chirped 5.5 ps pulses at a center wavelength of 1033 nm. The pulse repetition rate is 46.4 MHz, which results in an energy per pulse of 71 nJ. These pulses are extracavity dechirped down to 516 fs by using bulk gratings. The average power of the dechirped pulses is 2.3 W, which corresponds to a peak power of more than 96 kW.     

石墨烯被动锁模全正色散掺镱光纤激光器中的暗脉冲及其谐波

报道了一种基于石墨烯被动锁模的全正色散掺镱环形光纤激光器. 在激光器腔中应用激光诱导沉积法制备的石墨烯可饱和吸收体, 通过调节抽运光功率和偏振控制器的角度分别得到了明脉冲及其二阶谐波, 暗明脉冲对和暗脉冲及其二、三阶谐波这三类不同的脉冲. 其中, 暗明脉冲对和暗脉冲在基于石墨烯被动锁模的掺镱光纤激光器实验中都是第一次被观察到. 本文根据实验结果结合模拟分析了暗脉冲的产生机理, 并研究对比了明脉冲谐波和暗脉冲谐波产生的原因.     

High pulse energy mode-locked multicore photonic crystal fiber laser

A high pulse energy passively mode-locked fiber laser operating in the all-normal dispersion regime is demonstrated. The gain material is an Yb-doped multicore photonic crystal fiber with 18 cores in array-type geometry. Robust and self-starting mode locking is achieved using a fast semiconductor saturable absorber mirror. The laser generates 180?nJ chirped pulses at a 14.48?MHz repetition rate for an average power of 2.6?W. The 1.15?ps output pulses are compressed to 690?fs outside the cavity.     

High-power passive mode-locking of a diode pumped Yb:GdVO4 laser

Passive mode-locking of a diode pumped Yb-doped GdVO₄ crystal laser was demonstrated for the first time to our knowledge. The laser was mode-locked at the wavelength of 1019.1 nm and had an average output power of 1.01 W. The mode-locked pulse duration was 3.1 ps. The laser was end-pumped by a high-power fiber pigtailed laser diode bar and the mode-locking was enabled by a semiconductor saturable absorber mirror (SESAM).     

碳纳米管锁模双包层光纤激光器的实验研究

本文采用双包层掺镱光纤作为增益介质,用单壁碳纳米管作为饱和吸收体,获得最高输出功率为336 mW的锁模脉冲激光.用飞秒激光诱导水击穿法直接在单模光纤上制备出D形区,通过在D形光纤上滴涂单壁碳纳米管溶液,成功制备出碳纳米管饱和吸收体,并对其饱和吸收特性进行测试,发现其调制深度为27％.利用该饱和吸收体作为锁模器件,制备出具有环形腔结构的锁模光纤激光器.当抽运功率为4W时,获得了脉宽为93.8 fs,中心波长为1083.8 nm,3 dB谱宽为8.6 nm,重复频率为5.59 MHz,平均功率为336 mW的飞秒脉冲激光输出.     

输出近百纳焦耳脉冲能量的光子晶体光纤锁模激光器

设计并搭建了一种支持百纳焦耳量级的单脉冲能量输出的锁模光纤激光器.激光器基于σ型腔结构,采用掺Yb偏振型大模场面积光子晶体光纤作为增益介质,利用半导体可饱和吸收镜实现自启动锁模.激光器内没有色散补偿机理,使其工作在全正色散锁模状态.通过在谐振腔内引入多通长腔使激光器的重复频率降低至11.1 MHz,直接获得了平均功率为1.08 W,单脉冲能量为 97 nJ,脉冲宽度为4.17 ps的稳定锁模脉冲输出,经腔外色散补偿,脉冲宽度压缩至740 fs.     

Stable nanosecond pulse generation from a graphene-based passively Q-switched Yb-doped fiber laser

We demonstrate stable 70?ns pulse generation from a Yb-doped fiber laser passively Q-switched by a graphene-based saturable absorber mirror in a short linear cavity. The maximum output power was 12?mW and the highest single pulse energy was 46?nJ. The repetition rate of the fiber laser can be widely tuned from 140 to 257?kHz along with the increase of the pump power. To the best of our knowledge, this is the first report for passively Q-switched sub-100-ns pulse operation of a graphene-based saturable absorber in a Yb-doped fiber laser.     

Mode-locked ytterbium fiber laser tunable in the 980-1070-nm spectral range

Spectral tuning of a mode-locked Yb-doped fiber laser over a 90-nm range is reported. Using semiconductor saturable absorber mirrors in a fiber laser cavity incorporating a grating-pair dispersive delay line, we obtain reliable self-starting mode locking over the whole tuning range. The wide tuning range is achieved by optimization of reflection characteristics and bandgap energy of the multiple-quantum-well semiconductor saturable absorber and by proper engineering of the laser cavity.     

Zinc-oxide/PDMS-clad tapered fiber saturable absorber for passively mode-locked erbium-doped fiber laser

We propose and demonstrate a passively mode-locked erbium-doped fiber laser(EDFL) based on zincoxide/polydimethylsiloxane(Zn O/PDMS) saturable absorber(SA) that evanescently interacts with the light on a tapered fiber. The Zn O/PDMS composite is coated on the whole surface of the tapered fiber to guarantee the maximum efficiency of the SA device, with a measured insertion loss of 0.87 d B and a modulation depth of 6.4%. The proposed laser can generate soliton mode-locking operation at a threshold power of 33.07 m W. The generated output pulse yields a repetition rate and pulse width of 9.77 MHz and 1.03 ps, respectively. These results indicate that the proposed Zn O/PDMS-clad tapered fiber could be useful as an efficient, compatible, and low-cost SA device for ultrafast laser applications.     

被动谐波锁模掺Yb3+光纤环形激光器

 利用光纤的非线性偏振旋转效应产生可饱和吸收体的锁模机制，从掺Yb³⁺光纤环形激光器中得到稳定高阶谐波锁模光脉冲。理论分析了工作于正色散区的掺Yb³⁺光纤环形激光器的特性。实验中观测到了掺Yb³⁺光纤环形激光器3种不同演化方式产生高阶锁模光脉冲。4阶谐波锁模脉冲（107.2 MHz重复频率）经过1 m长高掺杂Yb³⁺光纤放大器放大后产生了平均功率100 mW，脉宽22.8 ps的脉冲，最后经过光栅压缩得到了平均输出功率20 mW，脉宽307 fs，脉冲中心波长1 051.2 nm，带宽13.76 nm的激光。     

高稳定性、高质量脉冲压缩飞秒光纤激光系统研究

报道了一款用于眼科手术的高稳定性、高质量脉冲压缩飞秒光纤主振荡功率放大系统. 振荡器采用混合腔方式增加了光纤双折射, 改善了非线性偏振旋转锁模在低重复频率下无法自启动的缺点, 提高了飞秒光纤激光器自启动锁模的稳定性. 研究了脉冲预啁啾与飞秒脉冲压缩质量的关系, 通过实验证明了光纤放大器的入射脉冲保持负的预啁啾状态可以得到最好的脉冲压缩结果. 实验最终实现了满足自启动锁模条件的重复频率19.4 MHz、平均功率1.2 W、脉冲宽度183 fs的激光脉冲, 目前这台激光器是国内首台具有自主知识产权并应用于动物角膜实验的飞秒光纤激光器.     

飞秒被动锁模光纤激光器的稳定性研究

从广义非线性薛定谔锁模方程出发，运用数值方法分别研究了泵浦光功率和非线性饱和吸收体对飞秒被动锁模光纤激光器工作特性的影响，并得到了激光器在基阶脉冲重复频率下稳态输出的最高输入泵浦功率和其对应的非线性饱和吸收体稳定工作区间。该研究结果为进一步优化设计最高泵浦功率、非线性饱和吸收体开关以及提高被动锁模光纤激光器的稳定工作性能都具有指导意义。     

Nanosecond Pulses Generation with Samarium Oxide Film Saturable Absorber

Nanosecond pulse generation is demonstrated in a mode-locked erbium-doped fiber laser(EDFL) utilizing a samarium oxide(Sm_2O_3) film. The Sm_2O_3 film exhibits a modulation depth of 33%, which is suitable for modelocking operation. The passively pulsed EDFL operates stably at 1569.8 nm within a pumping power from 109 to 146 m W. The train of generated output pulses has a pulse width of 356 nm repeated at a fundamental frequency of 0.97 MHz. The average output power of 3.91 m W is obtained at a pump power of 146 m W, corresponding to 4.0 nJ pulse energy. The experimental result indicates that the proposed Sm_2O_3 saturable absorber is viable for the construction of a flexible and reliably stable mode-locked pulsed fiber laser operating in the 1.5 m region.     

980-nm all-fiber mode-locked Yb-doped phosphate fiber oscillator based on semiconductor saturable absorber mirror and its amplifier

A 980-nm semiconductor saturable absorber mirror(SESAM) mode-locked Yb-doped phosphate fiber laser is demonstrated by using an all-fiber linear cavity configuration. Two different kinds of cavity lengths are introduced into the oscillator to obtain a robust and stable mode-locked seed source. When the cavity length is chosen to be 6 m, the oscillator generates an average output power of 3.5 m W and a pulse width of 76.27 ps with a repetition rate of 17.08 MHz. As the cavity length is optimized to short, 4.4-m W maximum output power and 61.15-ps pulse width are produced at a repetition rate of 20.96 MHz. The output spectrum is centered at 980 nm with a narrow spectral bandwidth of 0.13 nm. In the experiment, no undesired amplified spontaneous emission(ASE) nor harmful oscillation around 1030 nm is observed. Moreover,through a two-stage all-fiber-integrated amplifier, an output power of 740 m W is generated with a pulse width of 200 ps.     

Generation of wide-bandwidth pulse with graphene saturable absorber based on tapered fiber

Wide-bandwidth pulses were generated with a dispersion-managed erbium-doped passively mode-locked fiber laser based on a graphene saturable absorber. The graphene saturable absorber was composed of a tapered fiber deposited with graphene fabricated by liquid-phase exfoliation. The output pulse had a 3-dB bandwidth of 13.6 nm, which is the widest spectrum ever achieved with graphene-tapered-fiber saturable absorbers.     

Fabrication of aligned single wall carbon nanotube absorbers for high power passive mode-locked Nd:GdVO<Subscript>4</Subscript> laser

Using the vertical evaporation technique we fabricated saturable absorbers by transferring the water-soluble single wall carbon nanotubes (SWCNT) onto a hydrophilic quartz substrate. The fast recovery times of the absorber were measured to be 136 and 790 fs. The modulation depth of the absorber was about 2%. Passive mode-locked Nd:GdVO₄ laser using such an absorber was demonstrated. The continuous wave mode-locked pulses with the pulse duration of 12.4 ps and the repetition of 120 MHz were achieved. The maximum average output power of the mode-locked laser is 2.4 W at the pump power of 13 W. Such kind of absorber has potential to be put into practical use for high power solid-state laser mode locking.     

147 fs碳纳米管倏逝场锁模全光纤掺铒光纤激光器

利用化学腐蚀法在光纤包层表面成功制备了调制深度为3.9%的单壁碳纳米管饱和吸收体.组建了环形腔结构的全光纤掺铒光纤激光器,以制备的单壁碳纳米管薄膜为锁模元件,利用倏逝场锁模实现了锁模输出.锁模脉冲的中心波长为1556 nm,3 dB光谱带宽为24 nm,脉冲宽度为147 fs,重复频率为150 MHz.在520mW抽运功率下,平均输出功率为21 mW,相应的单脉冲能量为0.14 nJ.     

Reduced graphene oxide as saturable absorbers for erbium-doped passively mode-locked fiber laser

We demonstrate a nanosecond mode-locked erbium-doped fiber laser(EDFL)based on a reduced graphene oxide(RGO)saturable absorber(SA).The RGO SA is prepared by depositing the graphene oxide(GO)on fluorine mica through thermal reduction of GO.A scanning electron microscope(SEM),Raman spectrometer,and x-ray photoelectron spectroscopy(XPS)are adopted to analyze the RGO characteristics.The results show that the reduction degree of graphene oxide is very high.By embedding the RGO SA into the EDFL cavity,a stable mode-locked fiber laser is achieved with a central wavelength of 1567.29 nm and repetition rate of 12.66 MHz.The maximum output power and the minimum pulse duration are measured to be 18.22 mW and 1.38 ns respectively.As far as we know,the maximum output power of18.22 mW is higher than those of other nanosecond mode-locked oscillators reported.Such a nanosecond pulse duration and megahertz repetition rate make this mode-locked erbium-doped fiber laser a suitable seed oscillator for high-power applications and chirped pulse amplifications.     

2-μm mode-locked nanosecond fiber laser based on MoS_2 saturable absorber

We demonstrated a 2-μm passively mode-locked nanosecond fiber laser based on a MoS_2 saturable absorber(SA).Owing to the effect of nonlinear absorption in the MoS_2 SA, the pulse width decreased from 64.7 to 13.8 ns with increasing pump power from 1.10 to 1.45 W. The use of a narrow-bandwidth fiber Bragg grating resulted in a central wavelength and 3-dB spectral bandwidth of 2010.16 and 0.15 nm, respectively. Experimental results show that MoS_2 is a promising material for a 2-μm mode-locked fiber laser.