Side-chain crystallinity,heat of melting,and thermal transitions in poly[N-(10-n-alkyloxycarbonyl-n-decyl)maleimides] (PEMI)

The heat of melting, the melting temperature T_m, and the sub-T_g transition temperature have been studied from –120°C to above T_m in a series of 11 poly[N-(10-n-alkyloxycarbonyl-n-decyl)]-maleimides (PEMI). Side-chains from ethyl to n-docosyl with n even have been included. The contribution to the heat of melting per methylene group shows that the hexagonal paraffin crystal modification is present in these poly(N-maleimides), in agreement with x-ray data for the same compounds. The enthalpy data show that only a part of the outer methylene groups are present in the crystalline aggregates. Furthermore, DSC traces exhibit a typical distribution of crystallite sizes, which become narrower as the side-chains become longer. The critical chain length needed to form a stable nucleus includes nine methylene groups in the outer part of the n-alkyl side-chain. The influence of the side-chain length and crystallinity on the γ-transition temperature of these polymers was also investigated. In the range where these polymers are essentially amorphous the sub-T_g transition temperature decreases continuously as the number of methylene groups in the side-chain increases. This transition is attributed to internal motion within the external side-group without any interaction with the main chain. This is presumably made possibly by the partial rotation of the oxycarbonyl group. We suggest that this transition is similar to the well known γ transition which has been attributed to various segmental motions in all ethylene copolymers and in all homopolymers containing a determined number of? CH₂? units in the main-chain or in the side-chain. Estimates based on the chemical structure, yield a value for the γ transition of ? CH₂? similar to that measured by other methods in polyethylene and related materials.     

Order in poly(N-(10-n-alkyloxycarbonyl-n-decyl)-maleimides)

Wide-angle and small-angle x-ray diffraction patterns of 11 poly(N-(10-n-alkyloxycarbonyl-n-decyl)maleimides) (PEMI) (including only even members of the series) have been obtained on unoriented samples. They show major maxima at two diffraction angles. The one at the larger angles is due to the interaction of neighboring n-alkyl side-chains. The smaller one (which shows second and third orders of diffraction in higher members of the series, n = 14 to n = 22, where n is the number of methylene groups in the external n-alkyl sequence in the side chain) is related to the distance between lamellar planes formed by the main chains. In all cases, the measured layer separation d_i is higher than the structural unit length L of the side-chain in the most extended conformation, and lower than the length corresponding to two side-chains. On the basis of the experimental results reported here, a model is proposed for the packing of these comblike polymers in the solid state. The mode of packing is also supported by infrared spectra in the 720 cm^?1 region for the ? CH₂? rocking mode of vibration of the n-alkyl side-chain.     

A crystal transition in poly(γ-n-alkyl L-glutamate)s

A thermally reversible crystal transition was found for γ-helical poly(γ-n-alkyl L -glutamate)s (alkyl = ethyl, propyl, butyl, and amyl). The transition temperature is higher than that of the side-chain mechanical dispersion, and decreases from 115 to ?5°C, as the alkyl groups become longer. The transition in poly(γ-n-propyl L -glutamate) is clearly first order. The structures were analyzed by x-ray diffraction at various temperatures. It is noteworthy that the pseudohexagonal form observed below the transition temperature is less ordered than the hexagonal form at higher temperatures. The mechanism of this transition is discussed.     

Crystal transition and structure of poly (γ-n-alkyl glutamate)s

The nature of the crystal transition of the α-helical forms of poly (γ-n-alkyl glutamate)s (alkyl = ethyl, propyl, and butyl) is described. The transition is thermally reversible, and its temperature T₂ is much higher than the glasslike transition temperature T₁ associated with the side-chain motion. The main chains undergo large-scale motion (librational about the chain axis and translational along the axis) above T₃ ≈ 200°C. The structure observed below T₂ is anomalously disordered compared with that observed between T₂ and T₃. The crystal structure emerging above T₂ is analyzed for a typical sample of poly(γ-n-propyl L -glutamate). The trigonal unit cell contains three α-helices so that each helix is surrounded by other helices in the same fashion, but the helices are not interrelated by a crystallographic symmetry element. The side chains suffer no particular change at T₂. The main-chain motion gives rise to the T₂ transition by inducing attractive forces between interpenetrating side chains.     

Hydrophilic–hydrophobic AB diblock copolymers containing poly(trimethylene carbonate) and poly(ethylene oxide) blocks

AB‐type block copolymers with poly(trimethylene carbonate) [poly(TMC); A] and poly(ethylene oxide) [PEO; B; number‐average molecular weight (M_n) = 5000] blocks [poly(TMC)‐b‐PEO] were synthesized via the ring‐opening polymerization of trimethylene carbonate (TMC) in the presence of monohydroxy PEO with stannous octoate as a catalyst. M_n of the resulting copolymers increased with increasing TMC content in the feed at a constant molar ratio of the monomer to the catalyst (monomer/catalyst = 125). The thermal properties of the AB diblock copolymers were investigated with differential scanning calorimetry. The melting temperature of the PEO blocks was lower than that of the homopolymer, and the crystallinity of the PEO block decreased as the length of the poly(TMC) blocks increased. The glass‐transition temperature of the poly(TMC) blocks was dependent on the diblock copolymer composition upon first heating. The static contact angle decreased sharply with increasing PEO content in the diblock copolymers. Compared with poly(TMC), poly(TMC)‐b‐PEO had a higher Young's modulus and lower elongation at break. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4819–4827, 2005     

Photon correlation spectroscopy of syndiotactic poly (n-butyl methacrylate) near the glass transition

Slow relaxing longitudinal density fluctuations in bulk syndiotactic poly (n-butyl methacrylate) [PBMA] were studied by photon correlation spectroscopy as a function of temperature from 70 to 90°C. The shape of the light-scattering relaxation function broadened as the temperature approached the glass transition (T_g = 55°C). The average relaxation time shifted with temperature, consistent with previous studies of PBMA. The relaxation functions were analyzed in terms of a distribution of relaxation rates. The calculated distribution was clearly bimodal and the shape altered with temperature. The higher frequency peak in the distribution corresponds well with previous mechanical and dielectric relaxation studies of the intramolecular relaxation of the acrylate ester side chain. The resolution of the distribution into two modes is due to a well-defined side-chain motion with relaxation strength comparable to the primary glass-rubber relaxation. © 1994 John Wiley & Sons, Inc.     

Synthesis and polymerization of N-[N′-(α-methylbenzyl)aminocarbonyl-n-alkyl]maleimide

Two types of optically active N-[N′-(α-methylbenzyl)amino/carbonyl-n-alkyl]maleimides (MBAC) were synthesized from maleic anhydride, 6-amino-n-caproic acid (or 12-amino-n-dodecanoic acid), and (R)-(+)-α-methylbenzylamine. Radical homopolymerizations of MBAC were performed in several solvents at 60 and 110°C for 24 h to give optically active polymers. Radical copolymerizations of MBAC were performed with styrene (ST) and methyl methacrylate (MMA) in dioxane at 60°C. The monomer reactivity ratios and the Alfrey-Price Q-e values were determined. Chiroptical properties of the polymers and copolymers were investigated. © 1995 John Wiley & Sons, Inc.     

Highly phenylated poly(aryl ether phthalazine)s

Two series of novel amorphous poly(aryl ether phthalazine)s have been prepared via an intramolecular ring closure reaction of poly(aryl ether ketone)s (PAEKs) with hydrazine monohydrate. Fluorinated PAEKs, which display solubility in solvents incorporating a ketone functionality such as acetone or ethyl acetate, were converted to poly(aryl ether phthalazine)s to observe if these polymers would display similar solubility characteristics. The poly(aryl ether phthalazine)s have glass transition temperatures in the range of 278–320°C and show 5% weight loss points greater than 500°C in air and nitrogen atmospheres. The fluorinated poly(aryl ether phthalazine)s were not soluble in ketonic solvents. A series of poly(aryl ether phthalazine)s incorporating pendant 2-naphthalenyl moieties has been prepared in an attempt to produce amorphous, thermally stable polymers with high glass transition temperatures. The polymers have glass transition temperatures in the range of 287–334°C and show 5% weight loss points greater than 500°C in air and nitrogen atmospheres. Poly(aryl ether phthalazine)s undergo an exothermic reaction above the glass transition temperature. The major product of this reaction is a rearrangement of the phthalazine moieties to quiazoline moieties, however some crosslinking of the polymers occurs. Cured samples of the poly(aryl ether phthalazine)s show a small increase in the polymer T_g and are insoluble in all solvents tested. © 1996 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 34:1897–1905, 1996     

Ion conductive poly(ethylene oxide-dimethyl siloxane) copolymers

A series of poly(ethylene oxide-dimethyl siloxane) copolymers, — [SiMe₂O(CH₂CH₂O)_n]_m — (n = 2, 3, 4, 5, 6.4, 8.7, 13.3), were synthesised by the reaction of polyethylene glycol with dimethyl dimethoxy/diethoxysilane. Corresponding ion-conductive polymers were prepared by complexing these copolymers with salts (sodium tetrafluoroborate or ammonium adipate). The highest conductivity of these systems at room temperature was 3 × 10⁻⁴ S cm⁻¹ and 6 × 10⁻⁵ S cm⁻¹, respectively. The glass transition temperature of these copolymers is reported and is seen to be dependent on the length of the ether units. The effects of siloxane content, salt concentration, and temperature on the conductivity are discussed. © 1996 John Wiley & Sons, Inc.     

New Poly(4-Chloro)Maleimides. I. Synthesis and Characterization of Poly[Ether-Ester-(4-Chloro)Maleimides]

Abstract

New poly[N-(ester)-3-(ether)-4-(chloro)]maleimides were synthesized by the reaction of N-(4-chlorocarbonylphenyl)-3,4-dichloromaleimide (3) with various bisphenols such as hydroquinone (8a), 2,2-bis-(4-hydroxyphenyl)propane (8b), 4,4′ -(hexafluoroisopropylidene)diphenol (8c), and 2,5-bis(4-hydroxybenzylidene)cyclopentanone (8d). The structures of the resulted polymers were confirmed by IR and elemental analyses. A series of model compounds (4–7) was synthesized to facilitate confirmation of the structure of the polymers. The polymer containing hydroquinone units (9a) exhibited LC behavior in the melt, as observed by PLM measurements.     

Anchoring of hydrophobically modified poly(sodium acrylate)s into DDP vesicle bilayers: hydrophobic match and mismatch

 Differential scanning microcalorimetric thermograms have been recorded for aqueous solutions containing vesicles formed by sodium di-n-dodecyl phosphate, in the presence of different concentrations of poly(sodium acrylate-co-n-alkyl methacrylate), where n-alkyl= C₉H₁₉, C₁₂H₂₅, C₁₈H₃₇. The mole fraction of hydrophobic moieties in the copolymer is 0.04. The main phase transition temperature (T _m) is hardly affected by the presence of poly(sodium acrylate)s bearing n-dodecyl chains, whereas the anchoring of polymers bearing n-nonyl or n-octadecyl groups reduces the main phase transition temperature significantly from ca. 34 °C to ca. 32 °C. In parallel, the enthalpy of transition per mole of DDP monomer (Δ_m H _int) is lowered upon adding polymer. Again, the polymer containing n-dodecyl moieties hardly affects Δ_m H _int. These patterns are explained by the notion that the extent of the disruptive effect of alkyl chains incorporated into the bilayer depends on the extent of the mismatch between the chain lengths of the intruding alkyl chains and the hydrophobic moieties composing the vesicle bilayer. Added hydrophobically modified polymers increase the cooperativity of the melting process, as shown by the increase of n _DDP. We suggest that the anchoring poly(sodium acrylate-co-n-alkyl methacrylate) relieves the strain in the curved outer monolayer of a pure DDP bilayer by allowing the presence of larger “patches” characterized by low curvature. Received: 12 May 1997 Accepted: 20 October 1997     

Dielectric relaxations and electrical conductivities of poly(alkyl methacrylates) under high pressure

Dielectric properties of four methacrylate polymers (methyl, ethyl, n-butyl and n-octyl) were studied in the frequency range 0.0001 cps–300 kcps at temperatures above and below the glass transition temperature and at various pressures up to 2500 atm. At temperatures well above T_g a single relaxation peak (α′ peak) was observed in the case of the higher n-alkyl methacrylates. However, this peak was split into two peaks, α and β, with decrease in temperature or increase in pressure. The molecular motions corresponding to the α and the β relaxation processes are the micro-Brownian motions of amorphous main chains and of flexible side chains, respectively. From the temperature and the pressure dependence of the average dielectric relaxation time of these polymers the single relaxation process (the α′ process) was attributed to the micro-Brownian motion of the main chain coupled with that of the side chain. The effects of temperature and pressure on the d.c. conductivity of these polymers were also studied.     

Glass and subglass transitions in a series of poly(itaconate ester)s with methyl-terminated poly(ethylene oxide) side chains

A series of poly(itaconate ester)s containing methyl-terminated poly(ethylene oxide) side chains with lengths ranging from 1 to 5 ethylene oxide units has been synthesized. Both heat capacity C_p and dynamic mechanical measurements have been carried out on these polymers using differential scanning calorimetry (DSC) and torsional braid analysis (TBA), respectively. The resulting data for this polymer series are discussed, and comparisons are made with work previously published for the corresponding di-n-alkyl itaconate ester polymers where appropriate.     

Side-chain crystallinity. V. Heats of fusion and melting temperatures on monomers whose homopolymers have long side chains

Heats of fusion and melting temperatures were obtained for selected monomeric n-alkyl acrylates, N-n-alkylacrylamides, and vinyl esters. The corresponding thermodynamic parameters for homopolymers, derived from these monomers, had been reported previously from this laboratory. The α-hexagonal crystal modification was indicated near the melting point for the higher n-alkyl acrylates, but a β form was stable at low temperatures for the entire series. The magnitude of the heats of fusion indicated β polymorphs for vinyl esters in support of x-ray diffraction analysis from the literature. Because hexagonal crystal geometry prevailed in all reported homopolymers having long side chains, greater emphasis was placed on thermodynamic data for monomers exhibiting this crystal modification. Accordingly, a convergence temperature was estimated statistically for the α-hexagonal crystal modification of these systems and appropriate literature values of the n-alkanes and ethyl esters. The convergence temperature was computed to be 135°C, uncorrected for the entropy of disorientation. The anomalously large interfacial end-packing-defect energy of the poly(n-alkyl acrylates) and the poly-N-n-alkylacrylamides was shown to be associated with a high energy barrier to molecular transport in the melt as the vitreous state was approached. In support of this conclusion, similarity of the glass and melting transition temperatures of these homopolymer homologs occurred near their critical side-chain lengths, below which the homopolymers are amorphous. A special critical requirement of nucleus length was not indicated from rough estimations of nucleation parameters for the poly(n-alkyl acrylates). These findings lent increased, but still not unqualified, support to an x-ray diffraction study from the literature. The latter had specified the inclusion of the entire side chain and the main-chain units in the crystal lattices of the higher poly(n-alkyl acrylates).     

Solution-grown crystal of poly[bis(4-isopropylphenoxy)phosphazene]

The structural features of poly[bis(4-isopropylphenoxy)phosphazene] (PB(4-ip)PP) have been studied by electron microscopy, X-ray diffraction and differential scanning calorimetry techniques. Its orthorhombic lattice constants are determined as follows: a = 3,14 nm, b = 1,14 nm, c = 0,992 nm. The space group of this polymer is suggested to be P 2₁2₁2₁–D, and the molecular conformation of the chains possibly to be (trans₃cis)₂. This polymer exhibits a crystal/crystal transition at 86°C below its T(1) transition (120°C). The thermal behavior is similar to the characteristics of poly[bis(p-methoxyphenoxy)phosphazene].     

Adsorption of protein on the surface of thermosensitive poly(methyl methacrylate) microspheres modified with the N-(2-hydroxypropyl)methacrylamide and 2-(methacryloyloxy)ethyl phosphorylcholine moieties

A series of microspheres composed of methyl methacrylate (MMA) and N-(2-hydroxypropyl)methacrylamide (HPMA), and/or 2-(methacryloyloxy)ethyl phosphorylcholine (MPC), i.e., binary copolymer microspheres [poly(HPMA-co-MMA)_KPS and poly(HPMA-co-MMA)_ABIP] and ternary ones [poly(HPMA/MPC-co-MMA)_KPS and poly(HPMA/MPC-co-MMA)_ABIP], were prepared by emulsifier-free emulsion copolymerization using potassium peroxodisulfate (KPS) or 2,2′-azobis[2-(imidazolin-2-yl)propane] dihydrochloride (ABIP) as initiators. The decrease in ζ-potential of the polymer microspheres is caused by the addition of the HPMA and/or MPC moieties. Equilibrium water content of poly(HPMA-co-MMA)_ABIP showed a remarkable swelling change with a change in response to temperature: the hydrated conformation at 28°C and the dehydrated one at above 40°C. The adsorption of protein on the polymer microspheres also changed in response to change in temperature. The ternary polymer microspheres effectively suppressed the adsorption both of Alb and Glo, less than binary ones. A series of polymer microspheres are expected to apply as a novel drug carrier with both thermosensitive and nonthrombogenic functions. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 3349–3357, 1997     

Preparation and thermal properties of asymmetrically substituted poly(silylenemethylene)s

Poly(silylenemethylene)s of the types [SiMeRCH₂]_n and [SiHRCH₂]_n were prepared by the ring-opening polymerization (ROP) of 1,3-disilacyclobutanes (DSCBs) containing n-alkyl substituents, such as C₂H₅, n-C₃H₇, n-C₄H₉, n-C₅H₁₁, and n-C₆H₁₃, or a phenyl group on the Si. These new polymers include a monosilicon analog of poly(styrene), [SiHPhCH₂]_n. Improved synthesis routes to the DSCB monomers were developed which proceed through Grignard ring closure reactions on alkoxy-substituted chlorocarbosilanes. All of these asymmetrically substituted polymers were obtained in high molecular weight form, except for [SiHPhCH₂]_n. The configurations of all of the polymers were found to be atactic. The aryl-substituted polymers have higher glass transition temperatures (T_gs) and thermal stability than those of the alkyl-substituted poly(silylenemethylene)s. Unlike the polyolefins of the type [C(H)(R)CH₂]_n, where T_g drops continuously from R = Me to n-Hex, the T_gs of the n-C_nH_2n+1 (n = 2–6)-substituted [SiMeRCH₂]_n PSM's appear to reach a maximum (at −61°C) for the R = n-Pr-substituted polymer. Moreover, where it was possible to make direct comparisons among similarly substituted atactic polymers, all of the poly(silylenemethylene)s were found to have lower T_gs than their all-carbon analogs. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3193–3205, 1997     

Synthesis and characterization of new AB-type poly(etherimide)s containing bisphenol moieties

A series of new AB-type poly(etherimide)s having bisphenol-type moiety was prepared by the one-pot polyimidization using triphenylphosphite(TPP) in N-methyl-2-pyrrolidone(NMP)/pyridine solution at 150°C. Complete cyclodehydration was observed in the polymerizations as well as in model reactions. Polymers were obtained with inherent viscosities in the 0.27–0.49 dL/g range. The M_n and M_w/M_n of poly[4-(1,4-phenyleneoxy-1,4-phenylenehexafluoro-isopropylidene-1,4-phenylene)oxyphthalimide] (4d) with η_inh = 0.49 dL/g were 73,400 g/mol and 1.5, respectively. Most polymers could readily be dissolved in common organic solvents such as DMAc, NMP, and m-cresol. The polymer 4d was soluble even in chloroform. These polymers had glass transition temperatures between 205 and 235°C, and 5% weight loss temperatures in the range of 511–532°C in nitrogen. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3530–3536, 1999     

Polymerization of [o-(trimethylgermyl)phenyl] acetylene and polymer characterization

[o-(Trimethylgermyl)phenyl]acetylene was polymerized in the presence of WCl₆, W(CO)₆-hv, etc., to give polymers whose weight-average molecular weights reached ca. 7.0 X 10⁵ at the highest. When the MoOCl₄-n-Bu₄Sn-EtOH (1 : 1 : 1) catalyst was used, the polydispersity ratio of the polymer obtained was 1.08, and the number-average molecular weight increased in direct proportion to monomer conversion; these indicate that this polymerization is a living polymerization. The polymer had the structure ? [CH?C(C₆H₄-o-GeMe₃)]_n ? and was a dark purple solid (λ_max = 551 nm, ε_max = 6100 M^-1 cm^-1 in THF) soluble in organic solvents such as toluene and chloroform. The onset temperature of weight loss of the polymer in TGA in air was ca. 230°C, and the glass transition temperature was above 180°C. The Po₂ of the present polymer is 105 barrers—larger than the value of natural rubber and fairly close to that of poly(dimethylsiloxane). © 1993 John Wiley & Sons, Inc.     

Study of the miscibility of poly(styrene-co-4-vinylbenzoic acid) with poly(ethyl methacrylate) or with poly[ethyl methacrylate-co-(2-N,N-dimethylaminoethyl) methacrylate] by inverse gas chromatography

Poly(styrene) is immiscible with poly(ethyl methacrylate). The introduction of a small amount of 4-vinylbenzoic acid units along poly(styrene) chains (PS-VBA) enhanced its miscibility with poly(ethyl methacrylate) (PEMA) or with poly[ethyl methacrylate-co-(2-N,N-dimethylaminoethyl) methacrylate] (PEMA-DAE), as observed from the appearance of a single composition dependent glass transition temperature for each binary system using inverse gas chromatography. The negative values of the apparent polymer-polymer interaction parameter, chi(23)app, determined with different families of molecular probes, for three blend compositions and over a range of temperature confirm quantitatively the miscibility of these blends. The chi(23)app values for PEMA(PS-VBA) and (PEMA-DAE)-(PS-VBA) blends are dependent of the chemical nature of the probes, the temperature and the blend composition.