Effects of thermal treatment of biaxially oriented poly(ethylene terephthalate)

Two distinguishable effects of thermal exposure of biaxially oriented poly(ethylene terephthalate) (PET) have been observed in the temperature range from room temperature to 140°C. Upon heating above the glass transition temperature T_g of the film an irreversible shrinkage of a few percent occurred with a concomitant decrease in the rate of creep. Some loss of orientation in the noncrystalline phase with an attendant slight increase in density is believed to be responsible. Since the film was anisotropic in its plane, different amounts and rates of shrinkage were observed along with differing thermal expansion coefficients in various directions relative to the primary optic axis. Upon cooling the 50% crystalline PET from above T_g to lower temperatures, reversible “physical aging” was observed. Creep rates were found to decrease with the residence time below T_g. As with purely amorphous polymers, the effects of the aging are removed by heating the specimen above T_g where the density of the amorphous phase achieves equilibrium values.     

The relationship between the physical structure and the mechanical properties of polycarbonate

The room-temperature tensile mechanical properties and fracture topographies of polycarbonate are reported as a function of strain rate, sample preparation, and thermal history above and below T_g. The bulk physical structural changes produced by various thermal treatments were monitored by density, yield stress, and differential scanning calorimetry observations. Ordered regions do not form in bulk polycarbonate at or below 145°C. The changes produced in the mechanical properties of polycarbonate on annealing below T_g, relative to a quenched or 145°C equilibrium-state glass, are caused by liquidlike packing changes in free volume. In room-temperature tensile a 125°C–6 day annealed glass exhibits transitional behavior from shear free volume, such as quenched and 145°C equilibrium-state glasses, this transition occurs at higher strain rates. Polycarbonate embrittles as a result of the cessation of shear yielding and reversion to a crazing failure mode with a corresponding decrease in molecular flow and energy to failure. Density measurements indicate that ordered regions do start to grow immediately above 145°C in bulk polycarbonate. This phenomenon allows precrystalline and/or crystalline entities to grow below the bulk T_g in thin films and on the free surfaces of thick films where mobility restrictions are less severe than in the bulk. From bright-field transmission electron micrographs of thin films and carbon–platinum surface replicas of etched thick films it is suggested that the observed spherical precrystalline structures are aggregates of 50–60 Å ordered molecular do mains.     

The physical properties of bisphenol-a-based epoxy resins during and after curing. II. Creep behavior above and below the glass transition temperature

The creep behavior of a series of fully cured epoxy resins with different crosslink densities was determined from the glassy compliance level to the equilibrium compliance J_e at temperatures above T_g and at the glassy level below T_g during spontaneous densification at four aging temperatures, 4,4-diamino diphenyl sulfone DDS was used to crosslink the epoxy resins. The shear creep compliance curves J(t) obtained with materials at equilibrium densities near and above T_g were compared at their respective T_gs. T_gs from 101 to 205°C were observed for the epoxies which were based on the diglycidyl ether of bisphenol A. Creep rates were found to be the same at short times, and equilibrium compliances J_e were close to the predictions of the kinetic theory of rubberlike elasticity. Time scale shift factors determined during physical aging were reduced to T_g. At compliances below 2 × 10^?10 cm²/dyn, Andrade creep, where J(t) is a linear function of the cube root of creep time, was observed. The time to reach an equilibrium volume at T_g was found to be longer for the epoxy resin with lower crosslink densities. The increase of density during curing is illustrated for the epoxy resin with the highest crosslink density.     

Thermal behavior of polytriazole films: A thermal analysis study

The thermal behavior of poly(1,3-phenyl-1,4-phenyl)-4-phenyl-1,2,4-triazole has been investigated using different scanning calorimetry (DSC) and thermogravimetry (TG). Processes are studied for this thermally stable polymer that take place between 200 and 500°C. While the polycondensation reaction product in powder from appeared to be partially crystalline, films prepared by casting from a formic acid solution appeared to be completely amorphous. A thermal treatment between T_g(～ 270°C) and T_m(～ 430°C) can introduce crystallinity in the films because of the polymer's ability to cold crystallize. The cold crystallization temperature T_c seems to be dependent on the preparation history of the solid polymer phase. Thermal annealing of the films just below T_g does not introduce crystallinity but inhibits subsequent cold crystallization at higher temperatures. Crystallization upon cooling from the crystalline melt has not been observed either. At temperatures just above the crystalline melting point the polymer starts to decompose in an exothermic reaction.     

Effect of previous thermal history on physical aging of amorphous poly (ethylene terephthalate)

Physical aging of amorphous PET, at aging temperatures (T_a) of 40 and 60°C and different aging times (t_a), has been studied by DSC using two kinds of samples with different thermal history: Liquid-Nitrogen-Quenched samples (LNQ) and DSC cooled samples at a controlled cooling rate of 60 K/min (CC). At T_a = 40°C, a sub-T_g peak appears in LNQ samples but is not clearly observed in the CC samples. At T_g = 60°C, a superposed peak to T_g is observed in both kinds of samples. This different behaviour can be explained considering the distribution of relaxation times in the polymer.     

The design,synthesis, and nonlinear optical properties of novel X‐type polyurethane containing dicyanovinylnitroresorcinoxy group with enhanced SHG thermal stability

Novel X‐type polyurethane 5 containing 4‐(2′,2′‐dicyanovinyl)‐6‐nitroresorcinoxy groups as nonlinear optical (NLO) chromophores, which constitute parts of the polymer backbone, was prepared and characterized. Polyurethane 5 is soluble in common organic solvents such as acetone and N,N‐dimethylformamide. It shows thermal stability up to 280 °C from thermogravimetric analysis with a glass transition temperature (T_g) obtained from differential scanning calorimetry thermogram of around 120 °C. The second harmonic generation (SHG) coefficient (d₃₃) of poled polymer film at 1064‐nm fundamental wavelength is around 6.12 × 10^?9 esu. The dipole alignment exhibits a thermal stability even at 5 °C higher than T_g, and there was no SHG decay below 125 °C due to the partial main chain character of the polymer structure, which is acceptable for NLO device applications. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Development of novel cardo‐containing phenylethynyl‐terminated polyimide with high thermal properties

A phenylethynyl‐terminated reactive diluent [Card‐4‐phenylethynylphthalic anhydride (PEPA)], which contained fluorenyl cardo structures, was successfully synthesized and used as a modifier for flexible phenylethynyl‐terminated imide oligomer (PEI‐PEPA). The chemical structure, crosslink characterization, molecular weights, and thermal properties of the products were characterized. The imide systems with addition of 10, 20, 30, and 40 wt% Card‐PEPA to PEI‐PEPA (PEI‐PEPA‐Card) and their cured resin systems were prepared. The thermal curing behaviors of imide systems at different heating rates were analyzed by using differential scanning calorimetry. Thermal properties such as glass transition temperature (T_g) and char yield at 800°C of the resultant resin systems were studied by differential scanning calorimetry, dynamic mechanical analysis, and thermogravimetric analysis. The rheological properties were also investigated using a dynamic rheometry. These properties were found to be outstanding compared with pure PEI‐PEPA. The uncured imide systems exhibited lower T_g and lower isothermal viscosity with addition of Card‐PEPA. Furthermore, the T_g and char yield of the cured resin systems increased with addition of Card‐PEPA. The cured resin systems containing 40 wt% Card‐PEPA exhibited the highest T_g of 359°C and char yield at 800°C of 66.5%. Copyright © 2016 John Wiley & Sons, Ltd.     

Influence of bond interchange reactions on mechanical behavior of solid poly(ethylene terephthalate)

Reported are a pair of studies exploring the possible role of transesterification during the deformation of poly(ethylene terephthalate) (PET) near its glass transition temperature. SANS experiments on PET-D/PET-H blends were carried out on films drawn according to the method of Petermann and Gohil at 70 and 90°C. In order to avoid effects of orientation on the SANS pattern, the measurements were made on liquid solutions made from the drawn material. The results show a decrease in the D-sequence length upon deformation, while the molecular weight of the chain is unchanged. This result indicates that bond exchange has taken place. Based upon the SANS results, an approximate activation energy in the 8–24 kcal/mol range is reported for bond interchange. To test the hypothesis that transesterification may play a role in the mechanical behavior of PET near T_g, creep measurements were carried out over a temperature range on either side of T_g. Activation energies obtained from time–temperature superposition shift factors showed a dual behavior: above T_g the activation energy matches those for diffusive processes in PET; below T_g the activation energy coincides with activation energies reported for exchange reactions in this material. The role of annealing prior to deformation is also reported, and it is shown that the activation energy increases rapidly with increasing annealing temperature. © 1996 John Wiley & Sons, Inc.     

Impact of chain architecture (branching) on the thermal and mechanical behavior of polystyrene thin films

The modulus and glass transition temperature (T_g) of ultrathin films of polystyrene (PS) with different branching architectures are examined via surface wrinkling and the discontinuity in the thermal expansion as determined from spectroscopic ellipsometry, respectively. Branching of the PS is systematically varied using multifunctional monomers to create comb, centipede, and star architectures with similar molecular masses. The bulk‐like (thick film) T_g for these polymers is 103 ± 2 °C and independent of branching and all films thinner than 40 nm exhibit reductions in T_g. There are subtle differences between the architectures with reductions in T_g for linear (25 °C), centipede (40 °C), comb (9 °C), and 4 armed star (9 °C) PS for ≈ 5 nm films. Interestingly, the room temperature modulus of the thick films is dependent upon the chain architecture with the star and comb polymers being the most compliant (≈2 GPa) whereas the centipede PS is most rigid (≈4 GPa). The comb PS exhibits no thickness dependence in moduli, whereas all other PS architectures examined show a decrease in modulus as the film thickness is decreased below ～40 nm. We hypothesize that the chain conformation leads to the apparent susceptibility of the polymer to reductions in moduli in thin films. These results provide insight into potential origins for thickness dependent properties of polymer thin films. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Effects of thermal treatment on biaxially oriented poly(ethylene terephthalate). II. The anisotropic glass temperature

Thermal properties of an anisotropic biaxially oriented Poly(ethylene terephthalate) (PET) were determined before and after further deformation of the Mylar film. Film shrinkage in different planar directions was monitored during and following initial heating. After stabilization for three days at 140°C, glass temperatures T_g were determined from the decrease in length of film strips and were found to vary in the different in-plane directions. An increase in anisotropy brought about by additional deformation in the direction of the greatest orientation enhanced the T_g difference from 8 to 16°C. T_g is highest in the direction of greatest orientation.     

Synthesis and nonlinear optical properties of novel Y‐type polyurethane containing tricyanovinylthiazole with enhanced thermal stability of second harmonic generation

A novel Y‐type poly[iminocarbonyloxyethyl‐5‐methyl‐4‐{2‐thiazolylazo‐4‐(1,2,2‐tricyanovinyl)}resorcinoxyethyloxycarbonylimino‐(3,3′‐dimethoxy‐4,4′‐biphenylene)] 4 containing 5‐methyl‐4‐{5‐(1,2,2‐tricyanovinyl)‐2‐thiazolylazo}resorcinoxy groups as nonlinear optical (NLO) chromophores, which constitute part of the polymer backbone, was prepared and characterized. Polyurethane 4 is soluble in common organic solvents such as acetone and N,N‐dimethylformamide. It showed a thermal stability up to 250 °C in thermogravimetric analysis thermogram and the glass‐transition temperature (T_g) obtained from differential scanning calorimetry thermogram was around 118 °C. The second harmonic generation coefficient (d₃₃) of poled polymer films at 1560 nm fundamental wavelength was around 8.43 × 10^?9 esu. The dipole alignment exhibited a thermal stability even at 12 °C higher than T_g, and there was no SHG decay below 130 °C due to the partial main‐chain character of the polymer structure, which is acceptable for NLO device applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1166–1172, 2010     

Homopolyimides containing both benzimidazole and benzoxazole with high Tg and low coefficient of thermal expansion

A pair of isomer diamines containing both benzimidazole and benzoxazole and derived homopolyimides were synthesized for the first time. Due to rich rigid and linear benzoazole units, as well as the strong intermolecular interactions from the hydrogen bonding and the charge transfer complexation (CTC), the obtained polyimides (PIs) exhibited outstanding thermal properties, including high thermal weight loss temperature (T_d5% = 540–561°C), high glass transition temperature (T_g = 392–421°C), and low coefficient of thermal expansion (CTE = 1.3–20.9 ppm/°C). In addition, the obtained PIs also showed ideal mechanical properties (T_S = 189–240 MPa, T_M = 4.1–5.0 GPa and E_B = 2.9%–4.7%). These potential novel PI films with high T_g and low CTE were expected to be applied to next generation of flexible display substrate material.     

Characterization and thermal stability of PMR polyimides using 7-oxa-bicyclo[2,2,1]hept-5-ene-2, 3-dicarboxylic anhydride as end caps

An anhydride monomer containing ether oxide bridge,7-oxa-bicyclo[2,2,1]hept-5-ene-2,3-dicarboxylic anhydride (ONA),was successfully synthesized by Diels-Alder reaction of furan and maleic anhydride.The ONA was also studied as an end-cap for the polymerization of monomer reactant(PMR) type polyimides.Three molecular weight levels of the ONA end-capped PMR resins were evaluated.The effects of process conditions of these novel PMR resins on thermal and mechanical properties were investigated.It was demonstrated that the imidized prepolymers using the end-cap have good processability,and the cured polyimide specimens exhibited good thermal stability.The initial decomposition temperature, T_d(ca.580℃) and glass transition temperature,T_g(330℃) of the novel resin(PI-20),prepared under optimum process conditions,compare favorably with the T_d(ca.620℃) and T_g(ca.348℃) of the state-of-the-art resin(PI’-20),respectively.     

Synthesis and thermal transitions of a soluble,main chain,nematic liquid crystalline polymer exhibiting a kinetically trapped,disordered structure

An aromatic copolyester composed of 25 mol % phenyl hydroquinone, 10 mol % isophthalic acid, 40 mol % chloroterephthalic acid, and 25 mol % t-butyl hydroquinone (PICT) has been synthesized. This amorphous, glassy polymer is soluble in common organic solvents such as methylene chloride. Thin, solution-cast films may be prepared which are in a metastable, vitrified, optically isotropic state. On first heating of an isotropic film at 20°C/min in a calorimeter, one glass transition is observed at low temperature (approximately 49°C) and is ascribed to the glass/rubber transition of the metastable, isotropic polymer. This thermal event is followed by a small exotherm due to the development of order during the scan, which results in a second T_g at approximately 125°C. This T_g is associated with the glass/rubber transition of the ordered polymer. Nematic order can be developed by thermal annealing. The lower T_g increases toward the upper T_g as annealing time is increased. For an initially isotropic film annealed at 90°C, the increase of the lower T_g with annealing time and the increase in birefringence observed by optical microscopy are governed by similar kinetics. Isotropization occurs in the temperature range of 250–300°C. The nematic polymer is slightly more dense than its isotropic analog. No detectable differences between isotropic and nematic samples were observed in rotating frame proton spin lattice relaxation times. © 1996 John Wiley & Sons, Inc.     

Physical aging of poly(ether sulfone)-modified epoxy resin

The physical aging process of 4,4′-diaminodiphenylsulfone (DDS) cured diglycidyl ether bisphenol-A (DGEBA) blended with poly(ether sulfone) (PES) was studied by differential scanning calorimetry (DSC) at four aging temperatures between T_g-50°C and T_g-10°C. At aging temperatures between T_g-50 and T_g-30°C, the experimental results of epoxy resin blended with 20 wt% of PES showed two enthalpy relaxation processes. One relaxation process was due to the physical aging of PES, the other relaxation process was due to the physical aging of epoxy resin. The distribution of enthalpy relaxation process due to physical aging of epoxy resin in the blend was broader and the characteristic relaxation time shorter than those of pure epoxy resin at the above aging temperatures (between T_g-50 and T_g-30°C). At an aging temperature between T_g-30 and T_g-10°C, only one enthalpy relaxation process was found for the epoxy resin blended with PES, the relaxation process was similar to that of pure epoxy resin. The enthalpy relaxation process due to the physical aging of PES in the epoxy matrix was similar to that of pure PES at aging temperatures between T_g-50 and T_g-10°C. © 1997 John Wiley & Sons, Inc.     

Functionality and structure of polymers. II. Photodimerization of polymer-bound anthryl groups and thermal dissociation of the photodimers

Anthryl groups bound to various polyesters and polyesterurethanes as side groups were photodimerized in solid state in a nitrogen atmosphere. The rate of photodimerization is strongly affected by polymer structure as observed in the photodimerization of dilute solutions. The results revealed the importance of segment mobility rather than local concentration of anthryl groups. Temperature effects on the rate of photodimerization indicated that the rate jumped above the glass transition temperature (T_g). A definite difference in photodimerization behavior was apparent between polyesters and polyesterurethanes. Anthryl groups in polyesters were to some extent photodimerized at T_g, whereas polyesterurethanes did not react at all. Hydrogen bonding in polyesterurethanes restricted the movement of anthryl groups and consequently additional energy was required to liberate them and allow photodimerization to proceed. The anthryl groups can be recovered from the photodimerized polymers by heating to 80–100°C. The activation energy of thermal dissociation of the photodimer depends to a great extent on polymer structure. These results were interpreted as being due to the strain brought about by photodimer formation exhibited this dependence. The photodimerization–thermal dissociation cycle was reversible (reversibility: 95–100% under nitrogen). A novel principle of reversible photomemory, based on dry unit processes that consisted of image recording above T_g, fixation of image by cooling below T_g, and image erasure at elevated temperature, was proposed.     

Solid-state coextrusion of poly(ethylene terephthalate). I. Drawing of amorphous PET

Films of uniaxially oriented poly(ethylene terephthalate) (PET), M _v = 81,000, have been drawn by solid-state coextrusion in the range 40–100°C surrounded by polyethylene. This is well below the PET melting temperature and in some cases below its glass transition temperature. Properties of the extrudates, such as degree of crystallinity, mechanical and thermal properties, were investigated as a function of coextrusion temperature and draw ratio (EDR ≤ 4.4). The results show that the percent crystallinity depends strongly on draw ratio, whereas its sensitivity to extrusion temperature is limited only to the highest draw ratio (4.4). On the other hand, Young's modulus was sensitive to both extrusion temperature and draw ratio, exhibiting a maximum at EDR = 4.4 and T_ext = 65°C. Above this temperature, moduli decrease apparently because of increased chain mobility, resulting in dissipation of chain orientation. Furthermore, changes in yield and tensile strength followed the changes in mechanical properties, suggesting that they are dominated by the same factors. The cold-crystallization temperature T_CC also revealed information about the morphological changes occurring during the extrusion drawing. For samples of EDR = 4.4, T_CC increased with extrusion temperature, suggesting again dissipation of orientation by thermal motions. On the other hand, T_CC decreases with EDR, and a ΔT_CC as high as 73°C was found. Conventional drawing of amorphous PET has been widely reported. To our knowledge this is the first time oriented PET has been prepared using the advantages of solid-state coextrusion.     

Dynamic mechanical relaxation effects in some poly(arylene sulfones)

Poly-4,4′-oxydiphenylenesulfonyl and poly-4,4′-methylenediphenylenesulfonyl were synthesized by an electrophilic substitution polymerization of the arylene monosulfonyl chloride monomers. The glass-transition temperatures T_g of these polymers were determined by calorimetric and dynamic mechanical measurements, and the number-average molecular weights were determined by vapor-pressure osmometry. Both polymers were found to have the same T_g at equivalent molecular weight; the limiting value at high molecular weight is 238°C. Both polymers have two dynamic mechanical relaxation peaks at temperatures far below T_g. One is in the neighborhood of 0°C, and the other is at ?110°C. Plausible origins for these relaxations, and the absence of any near 0°C in poly(4,4′-isopropylidenediphenylene-co-4,4′-sulfonyldiphenylene dioxide), are discussed.     

Improvement of thermal and mechanical properties of poly(L‐lactic acid) with 4,4‐methylene diphenyl diisocyanate

In this study, the thermal and mechanical properties of biodegradable poly(L ‐lactic acid) (PLA) were improved by reacting with 4,4‐methylene diphenyl diisocyanate (MDI). The resulting PLA samples were characterized with Fourier transformation infrared spectrometer (FT‐IR). The glass transition (T_g) and decomposing (T_d) temperature of the resulting products were measured using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), respectively. The tensile properties were also measured with a tensile tester. The results show that when the molar ratio of ? NCO to ? OH was 2:1, the T_g value can be increased to 64°C from the original 55°C, and the tensile strength increased from 4.9 to 5.8 MPa. This demonstrated that by reacting PLA with MDI at an appropriate portion, both the thermal and mechanical performance of PLA can be increased. Copyright © 2006 John Wiley & Sons, Ltd.     

Aromatic polyamides. III. Copoly(4,4′-oxanilideterephthalamide—4,4′-phenyleneterephthalamide): Synthesis,wet-spinning,fiber thermal characterization,and stability in sulfuric acid

Copoly(4,4′-oxanilideterephthalamide—4,4′-phenyleneterephthalamide) (A-202/PPD) was synthesized by reaction of 4,4′-diaminooxanilide, p-phenylenediamine, and terephthaloyl chloride in organic solvents. Copolymer inherent viscosities in H₂SO₄ as high as 10.3 were obtained. Isotropic copolymer solutions (4%—5% concentration) of A-202/40%–80% PPD were spun to fibers with tenacity/elongation/modulus at 1% extension in the 13–14 gpd/1.5%–2%/700–1000 gpd range. Oxamide and amide stabilities in 98–100% H₂SO₄ and 20% oleum were compared. Poly(4,4′-oxanilideterephthalamide) (A-202), A-202/PPD copolymers, and poly(4,4′-phenyleneterephthalamide) (PPT) were unstable in 20% oleum, but all proved relatively stable in 100% H₂SO₄. However, the oxamide linkage proved less stable than the amide linkage in 98% H₂SO₄. A-202 and A-202/PPD copolymers formed stable anisotropic spinning solutions in 1% oleum at 10–20% concentrations. Dynamic mechanical analyses (Vibron) showed no glass transition temperature (T_g) below 200°C. Dilatometric measurement of A-202/50% PPD revealed a T_g at 257°C. Differential thermal analyses of A-202/40–80% PPD exhibited endotherms at 470–480°C. Thermogravimetric analyses showed no significant weight loss below 400°C.