Solution behavior of ionomers. I. Metal sulfonate ionomers in mixed solvents

The solution behavior of metal sulfonate-containing ionomers has been investigated in various mixed solvent systems. Ionomers, such as lightly sulfonated polystyrene (sodium salt) and sulfonated ethylene-propylene-diene terpolymer (metal salts) are generally insoluble in typical hydrocarbon solvents, but readily dissolve when small amounts of alcohols or other polar cosolvents are present. At relatively low polymer concentration these ionomers display unusually high thickening behavior in nonpolar solvents when compared with nonionic polymers because of association of the metal sulfonate groups. The addition of modest levels of polar cosolvent markedly decreases the solution viscosity and gives rise to viscosity-temperature relationships different from those of conventional polymer solutions. For example, such solutions can display vicosities which increase, are relatively constant, or display maxima or minima over broad temperature ranges. These observations are interpreted as arising from a temperature-dependent preferential interaction of the cosolvent with the sulfonate groups. While these ionomers can be regarded as polyelectrolytes of low charge density, they do not display the typical “polyelectrolyte” behavior often observed in aqueous solutions. This anomalous behavior is attributed to the fact that the metal sulfonate groups are largely un-ionized in solvents of low dielectric constant. Therefore, the solution behavior is dominated by ion pair interactions rather than free ions.     

Comparisons of styrene ionomers prepared by sulfonating polystyrene and copolymerizing styrene with styrene sulfonate

As part of a continuing study of ion-containing polymers, a comparison has been made on styrene-based sulfonate ionomers obtained by two different processes. Copolymers of styrene with sodium styrene sulfonate (SSS) have been compared with corresponding polymers obtained by the sulfonation/neutralization of preformed polystyrene (S–PS). The former system covered a range of sulfonate level from 1 to 30 mol %, while the latter ranged from about 1 to 7 mol %. The characterization of these materials has been conducted using solubility behavior, dilute solution viscometry, thermal mechanical analysis, density measurements, and water adsorption studies. At low (ca. 1%) levels the solubility behavior of the SSS copolymers and the sulfonated polystyrenes were similar. However, at higher sulfonate levels the solubility behavior in different solvents and the dilute solution viscometry were significantly different for the two systems. Similarly, thermal analysis studies (DSC) showed that the glass transition of the sulfonated polystyrene increased linearly with sulfonate level, while the T_g for the SSS copolymer increased modestly, up to about 7 mol % sulfonate content, and then remained constant. Significant differences in the softening behavior and water absorption characteristics were also observed for these two classes of ionomers. Although molecular weights and molecular weight distributions are not now available for these ionomers, the differences in their behavior does not appear to be due simply to differences in molecular weight. It is postulated that the differences in the copolymer and the S–PS ionomers may originate with differences in sulfonate distribution. It is suggested that the SSS monomer units are incorporated as blocks in the copolymer as opposed to a more random distribution in the S–PS ionomer. Indirect evidence in support of his argument is found, for example, in the case of the copolymer in the solubility behavior, the relative independence of T_g on sulfonate concentration and the apparent existence of a second, high temperature transition tentatively attributable to an ion-rich phase. Additional studies are required to confirm this hypothesis.     

可交联含氟聚醚醚酮的合成

聚醚醚酮 (PEEK)是一种耐热等级高、耐化学药品、耐辐射并有优异的电性能及机械性能的特种工程塑料 .由于其综合性能优异 ,PEEK在航空航天、通信、电子和机械化工等领域获得成功应用 [1] .含氟芳香聚合物以其独特的性能而成为低介电常数微电子和低损耗光波导器件极具潜力的材料 [2 ] .聚合物良好的溶解性虽对光电集成电路的加工十分重要 ,但也要满足多层化操作过程 ,还要考虑器件成型后的抗化学药品性 .因而 ,在聚合物中引入可交联组分是必要和可行的方法 .另外 ,交联后的聚合物将有更高的玻璃化转变温度 (Tg)、更好的尺寸稳定性和防开…     

MOLECULAR INTERACTIONS OF CARBOXYLATED URETHANE ACRYLATE IONOMERS IN LOW-POLARITY AND POLAR SOLVENTS

Carboxylated urethane acrylate ionomers that have a small number of ionic groups per chain were synthesized with varying the molecular weight of soft segment, the degree of ionization, and the sort of diisocyanate. The effect of intra-and intermolecular interactions on solution properties was studied by viscosity measurements in low-polarity and polar solvents. In a low-polarity solvent (1,4-dioxane), ionomers showed almost no intramolecular interaction at dilute concentration and a small degree of intermolecular interaction at high concentrations, resulting from a small number of ionic groups per chain. In a polar solvent (dimethylacetamide, DMAc), ionomers showed typical polyelectrolyte behavior, even though ionomers have a small number of ionic groups per chain. Intermolecular interaction caused by polyether soft segment, phenyl group, and hydrogen bond between urethane acrylate ionomer chains contributed to the increase of reduced viscosity at low concentration.     

嵌段离聚物的制备及其络合和缔合性质

报道了一种氢化ＳＢＳ（ＳＥＢＳ）的化学改性方法，由此得到了一种基于ＳＥＢＳ的离聚物，其中ＰＳ嵌段接有少量羧酸盐基．用动态光散射和粘度法表征了基于ＳＥＢＳ的不同配对离子的磺酸离聚物在非极性溶剂中的缔合行为，给出了缔合物存在的证据和缔合物尺寸的定量数据．ＳＥＢＳ磺酸盐离聚物与含吡啶基的无规共聚物在稀溶液和本体中能形成分子间的络合物，这从共混物溶液粘度的反常增大和本体Ｔｇ的显著增加得到了证明．用粘度法、透射电子显微镜表征和证实了ＳＥＢＳ羧酸钠离聚物在水中可以形成稳定的胶体分散．疏水粒子为表面的离子基团所稳定．     

Properties of amorphous and crystallizable hydrocarbon polymers. III. Studies of the hydrogenation of polybutadiene

Three methods for hydrogenating anionically prepared polybutadiene (containing about 8% vinyl double bonds) were investigated: homogeneous catalysis (alkylated transition metal salts), heterogeneous catalysis (nickel on kieselguhr; paladium on calcium carbonate), and stoichiometric reaction with in situ generated diimide. The products were characterized by intrinsic viscosity, gel permeation chromatography, infrared spectroscopy, and melt viscosity. Only the heterogeneous catalysts were found to yield completely hydrogenated products without incorporation of foreign groups and without significant change in the large-scale molecular structure of the chain. The 195°C melt viscosity of linear polybutadiene hydrogenated with heterogeneous catalysts is virtually identical with that of linear polyethylene with the same intrinsic viscosity in trichlorobenzene at 135°C. The solid state properties of hydrogenated polybutadiene, containing about 20 ethyl branches/1000 main chain atoms, closely resemble those of commercial branched polyethylene.     

UV-curing behavior and adhesion performance of polymeric photoinitiators blended with hydrogenated rosin epoxy methacrylate for UV-crosslinkable acrylic pressure sensitive adhesives

UV-crosslinkable polyacrylates were synthesized for use as pressure sensitive adhesives (PSAs). These polyacrylates acted as polymeric photoinitiators due to the benzophenone incorporated into their backbones. Hydrogenated rosin epoxy methacrylate (HREM; based on hydrogenated rosin and glycidyl methacrylate) was also synthesized as a tackifier, and blended at different levels with the synthesized, UV-crosslinkable polyacrylates for use as PSAs. The effect of the new tackifier, HREM, on the properties of the UV-crosslinkable PSAs was examined in comparison with the properties exhibited by PSA/hydrogenated rosin blends. The characteristics of these PSA/tackifier blends were examined by Fourier-transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC) and an advanced rheometric expansion system (ARES). In addition, the adhesion performance of the PSA blends was investigated using probe tack tests. DSC and ARES revealed all the PSA blends with HREM or hydrogenated rosin to be miscible at the molecular level. The glass transition temperature (T_g) of HREM was −25.6 °C, which is lower than that of other commercially available rosin tackifiers. FTIR revealed changes in the relative concentration of benzophenone groups in the PSAs at 1580 cm⁻¹, which demonstrated that the crosslinking efficiency is proportional to the benzophenone content and UV dose, but decreases with increasing hydrogenated rosin content. However, the reduced crosslinking reaction efficiency was improved in the PSA/HREM blends due to the low T_g of HREM which only slightly increased the T_g of the PSA blends. Moreover, the relative initial decrease in the probe tack of the PSA/HREM blends was lower than that of the PSA/hydrogenated rosin blends after UV irradiation.     

Polyethers and thioethers incorporating neutral and cationic organoiron complexes

The synthesis of linear and star-shaped oligomers containing cationic and neutral organoiron groups in their structures was achieved by reaction of cationic arene complexes of cyclopentadienyliron containing terminal hydroxyl groups with 1,1′-ferrocenedicarbonyl chloride or ferrocene carboxylic acid. The use of chloroarene complexes allowed for the formation of triiron complexes that were subsequently polymerized via nucleophilic aromatic substitution with various oxygen- and sulfur-based dinucleophiles. The corresponding polyethers and thioethers were isolated in good yields and these materials exhibited excellent solubilities in polar organic solvents. Cyclic voltammetric investigations revealed that the cationic iron centers pendent to the polymer backbones underwent reversible reduction steps, while the neutral iron centers within the polymer backbones underwent reversible oxidation steps. Photolysis of these polymers resulted in the removal of the cationic cyclopentadienyliron moieties pendent to the polymer backbones. Thermogravimetric analysis (TGA) revealed that the cationic iron complexes were cleaved from the polymers at approximately 210 °C. Differentials scanning calorimetry (DSC) revealed that the glass transition temperatures of the cationic polymers occurred at higher temperatures than their neutral analogs.     

Synthesis of well-defined telechelic trans-1,4-polyisoprene by oxidative cleavage

Synthesis of telechelic trans-1,4-polyisoprenes(TPI: trans-structure 95%) was evaluated based on two different methods of oxidative cleavage(indirect cleavage: first epoxidation of TPI, then the selective cleavage of epoxidized units in epoxidized trans-1,4-polyisoprene(ETPI) and direct cleavage of isoprene units in TPI). The influence of solvents and the ratio of oxidative agents was investigated by 1H-NMR and 13C-NMR. A series of well-defined telechelic TPI with double terminated functional groups and less side reaction(molecular weight distribution range: 1.96?2.26) were synthesized by indirect cleavage in chloroform. Telechelic TPI showed similar crystallization behavior with TPI and interesting cold crystallization behavior characterized by DSC.     

Novel multiblock‐co‐ionomers as potential polymer electrolyte membrane materials

In this contribution a series of novel multiblock‐co‐ionomers consisting of hydrophobic (partially fluorinated) and hydrophilic (sulfonated) domains has been prepared and characterised in terms of their applicability as fuel cell membranes. The synthesis of these multiblock‐co‐ionomers is a four‐step procedure including (1) the sulfonation of the monomer 4,4′‐difluorodiphenylsulfone, (2) the preparation of hydrophilic telechelic macromonomers by molecular‐weight controlled step‐growth polycondensation of the sulfonated monomer with various bis(thio)phenols, (3) the preparation of a hydrophobic telechelic macromonomer and (4) the coupling of both telechelic macromonomers to yield microphase‐separated block‐co‐ionomers. This study focuses on the investigation of the influence of various linkage groups and atoms within the hydrophilic domains of the multiblock‐co‐ionomers. Both the telechelic macromonomers and the multiblock‐co‐ionomers were structurally investigated by ¹H‐ and ¹⁹F‐NMR spectroscopy and gel permeation chromatography (GPC). All multiblock‐co‐ionomers of this series could be cast into membranes and their membrane properties (ion‐exchange capacity, specific resistance, swelling ratio, water uptake, thermal and oxidative stability) were measured and discussed in dependence of the various linkage groups within the hydrophilic domains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5237–5255, 2007     

羧酸型聚乙二醇聚氨酯离聚物及其导电性能

以聚环氧乙烷（ＰＥＯ）为软段，与４，４’－二苯甲烷二异氰酸酯（ＭＤＩ）预聚，以２，２’－二羟甲基丙酸（ＤＭＰＡ）扩链合成了含羧酸基团的聚氨酯，并经中和形成了含不同金属离子的离聚物．测定了样品的热分析数据和力学性能，利用交流阻抗分析仪测定了样品的阻抗谱，由此计算出样品的离子电导率．这类样品由于阴离子（－ＣＯＯ－）固定在聚合物分子链上，因此只有单一阳离子迁移．结果表明，羧酸型聚氨酯离聚物既有较高的单一离子电导率又具有优良的力学性能．讨论了不同软段分子量、硬段含量和金属抗衡离子对离子电导性能的影响     

Solution behavior of metal sulfonate ionomers. II. Effects of solvents

Previous studies on the dilute-solution behavior of sulfonated ionomers have shown these polymers to exhibit unusual viscosity behavior in mixed solvents of low polarity. These results have been interpreted as arising from specific solvation effects by the solvents with the metal sulfonate groups which persist as ion pairs. The consequences of ion pair interactions and their solvation are exceptional thickening behavior at low polymer levels as compared to unfunctionalized polymers, and anomolous solution viscosities with varying temperature. These studies have now been extended to single-component solvents which traverse a range of polarities. Using the sodium salt of lightly sulfonated polystyrene (S-PS) as a model system, the authors found the solution behavior in low-polarity solvents (tetrahydrofuran) to be consistent with that observed previously for mixed solvents; ion pair interactions predominated. However, in polar solvents such as dimethyl sulfoxide or dimethyl formamide, these polymers behave as classic polyelectrolytes even at sulfonate levels below 2 mol %. The behavior of the S-PS acids is similar to that observed for the metal salts. To a first approximation these two behaviors, ion pair association and polyelectrolyte behavior, are dependent on solvent polarity. In some cases it is possible to induce polyelectrolyte behavior in a S-PS/solvent combination exhibiting ion pair interactions by the addition of very low levels of a polar cosolvent, such as water. These results again demonstrate the selectivity of the solvent-sulfonate interactions.     

Processable heat-resistant polymers. XI. Synthesis and characterization of unsaturated polyamideimides

Polycondensation of the diacid chloride of 2-(3-carboxy vinyl)phenyl-1,3-dioxoisoindoline-5-carboxylic acid with m-phenylenediamine and the diacid chloride of 2-(4-carboxy phenyl)-1,3-dioxoisoindoline-5-carboxylic acid with 1,5-bis(3-aminophenyl)1,4-pentadien-3-one was carried out in polar solvents to produce new unsaturated polyamide–imides. The solution and the thermal, electrical, and a few other properties of the polymers were studies. The polymers were soluble in highly polar solvents. The solubility parameter of the polymers was calculated from the Small's group contribution. The polymers were fairly thermostable and underwent crosslinking creaction when heated, preferably in the presence of a suitable catalyst. The crosslinked polymers were in soluble even in highly polar solvents and possessed higher thermal stability. The swelling behavior of the polymers was studied and the molecular weight between two consecutive crosslinks was determined. X-ray diffraction and the dielectric properties of the polymers and their crosslinked products were also studied.     

Ionomer-surfactant self-assembly in low-polarity solvents

A systematic study of complexation reactions of sulfonated polystyrene ionomers containing up to 5 molar percent of polar chain units with various oil-soluble surfactants is carried out in low-polarity organic solvents. Dipole-dipole attractions of the components lead to the formation of complexes characterized by limiting compositions and an unusual polymer-colloidal morphology of joint clusters and/or micelles. The limiting compositions (φ) for the complexes formed between ionomers and surfactant of the same charge (bis(2-ethylhexyl)sulfosuccinate sodium salt), or nonionic surfactants (primarily aliphatic amines) are equal to 15–30 surfactant molecules per one ionomer salt/acid group on average, with φ depending on the hydrophilic-lypophilic balance of the components, the initial aggregation state of surfactant and the nature of low-polarity solvent. Ionomersurfactant complexation is accompanied by disruption of self-contacts of ionomer salt/acid groups, leading to “unfastening” and expansion of the ionomer coils in dilute solution. The “driving force” of the ionomersurfactant complexation and the structure of the resultant complexes are discussed.     

Rapid dissolution of cellulose in LiOH/urea and NaOH/urea aqueous solutions

Rapid dissolution of cellulose in LiOH/urea and NaOH/urea aqueous solutions was studied systematically. The dissolution behavior and solubility of cellulose were evaluated by using (13)C NMR, optical microscopy, wide-angle X-ray diffraction (WAXD), FT-IR spectroscopy, DSC, and viscometry. The experiment results revealed that cellulose having viscosity-average molecular weight ((overline) M eta) of 11.4 x 104 and 37.2 x 104 could be dissolved, respectively, in 7% NaOH/12% urea and 4.2% LiOH/12% urea aqueous solutions pre-cooled to -10 degrees C within 2 min, whereas all of them could not be dissolved in KOH/urea aqueous solution. The dissolution power of the solvent systems was in the order of LiOH/urea > NaOH/urea > KOH/urea aqueous solution. The results from DSC and (13)C NMR indicated that LiOH/urea and NaOH/urea aqueous solutions as non-derivatizing solvents broke the intra- and inter-molecular hydrogen bonding of cellulose and prevented the approach toward each other of the cellulose molecules, leading to the good dispersion of cellulose to form an actual solution.     

Poly(alkylene oxide) ionomers. XII. Hydrolysis of polymers and copolymers of methyl 10,11-epoxyundecanoate

Ester-substituted oxyethylene polymers and copolymers of methyl 10,11-epoxyundecanoate were prepared with an aluminumalkyl–water coordination initiator system modified with acetylacetone. Poly(ethylene oxide) ionomers, polyelectrolytes, and polycarboxylic acids were obtained by alkaline hydrolysis of the pendant carbomethoxy groups and by neutralizations with acetic acid. The high molecular weight substituted poly(ethylene oxide)s were characterized by spectral, thermal, and dilute solution measurements. The infrared spectra of carboxylate substituted poly(ethylene oxide)s, both homo- and copolymers, show the typical shifts in the carboxyl absorption when going from the ester to the carboxylate group to the free acid. Polymer transitions temperatures, as measured by DSC, changed accordingly. Wide-angle x-ray diffraction measurements strongly suggest the existence of ionic domains in the oxyethylene polymer matrix. Dilute solution properties of the ionomers show typical polyelectrolyte behavior, including a substantial change in viscosity when ionic solute is added.     

Peroxide-initiated crosslinking of maleic anhydride-modified low-molecular-weight polybutadiene. I. Mechanism and kinetics of the reaction

The crosslinking mechanism and kinetics of low-molecular-weight polybutadiene, its mixtures with maleic anhydride, and the products of its grafting with maleic anhydride and styrene, using dicumyl peroxide (DCP) as an initiator, were studied. It was shown that for all systems crosslinking is a radical polymerization of the double bonds. Modification of polybutadiene changes only the kinetic parameters of the crosslinking reaction and causes mainly a decrease of the termination step velocity. From DSC data the crosslinking reaction order, activation energy, and reaction heats were calculated.     

Effect of Topology on the Properties of Poly(N-isopropylacrylamide) in Water and in Bulk

Three macrocyclic poly(N-isopropylacrylamide)s (PNIPAM) with molecular weight (MW) ranging from 6 to 19 kg/mol were synthesized by ‘click’ ring closure of the corresponding α-azido ω-propargyl telechelic linear PNIPAMs, themselves prepared by reversible addition fragmentation chain transfer (RAFT) polymerization of N-isopropylacrylamide. Differential scanning calorimetry (DSC) studies revealed that both the thermal phase separation in water and the glass transition in bulk of PNIPAM were affected by polymer topology. In aqueous solution, the cyclic polymers exhibit a higher phase separation temperature and broader phase transition range than the corresponding linear counterparts. In bulk, the cyclic polymers display a higher glass transition temperature of lesser molecular weight dependence, as compared to their linear precursors.     

Michael addition for crosslinking of poly(caprolactone)s

Poly(caprolactone) (PCL) networks have received significant attention in the literature because of many emerging potential applications as biodegradable materials. In this study, the Michael addition reaction was used for the first time to synthesize biodegradable networks using crosslinking of acetoacetate‐functionalized PCL (PCL bisAcAc) oligomers with neopentyl glycol diacrylate. Hydroxyl‐terminated PCL telechelic oligomers with number‐average molecular weights ranging from 1000 to 4000 g/mol were quantitatively functionalized with acetoacetate groups using transacetoacetylation. In addition to difunctional PCL oligomers, hydroxyl‐terminated trifunctional star‐shaped PCL oligomers were functionalized with acetoacetate groups. Derivatization of the terminal hydroxyl groups with acetoacetate groups was confirmed using FTIR spectroscopy, ¹H NMR spectroscopy, mass spectrometry, and base titration of hydroxyl end groups. PCL bisAcAc precursors were reacted with neopentyl glycol diacrylate in the presence of an organic base at room temperature. The crosslinking reactions yielded networks with high gel contents (>85%). The thermomechanical properties of the networks were analyzed to investigate the influence of molecular weight between crosslink points. The glass transition and the extent of crystallinity of the PCL networks were dependent on the molecular weight of the PCL segment. Dynamic mechanical analysis indicated that the plateau modulus of the networks was dependent on the molecular weight of PCL, which was related to the crosslink density of the networks. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5437–5447, 2009