Calibration of ion spray mass spectra using cluster ions

Mass calibration for ion spray mass spectrometry can be achieved by using cluster ions formed by flow injection of solutions of alkali metal salts in aqueous acetonitrile into the liquid flowing to the ion spray needle. Source contamination is thereby reduced to a minimum. For quadrupole mass analyzers, sodium iodide provides an ideal compromise between undesirable spectral complexity and spacings between calibrant mass peaks sufficiently close that interpolation errors are negligible. When much closer spacings are required, protonated water clusters provide an excellent calibration up to about m/z 1000. If higher mass ranges are required with a large number of calibrant peaks, a solution of mixed alkali metal iodides does provide the expected spectra but intensities are poor at higher m/z values. For liquid chromatography with on-line mass spectrometry (LC/MS) the mass calibration may be checked without changing the mobile phase by post-column flow injection of a cesium carbonate solution, since the carbonate anion is wholly displaced by the anion of the mobile phase acid modifier, resulting in no mixed clusters. The metal salt calibrants have the additional advantage of being useful over a wide range of tuning parameters in the atmospheric pressure ionization source, covering those appropriate to both relative molecular mass determinations of large proteins and to LC/MS of small analyte species.     

On the mechanism of ion formation from the aqueous solutions irradiated with 3 microm IR laser pulses under atmospheric pressure

The mechanism of atmospheric pressure (AP) laser ionization of water and water/glycerol liquid samples at a 3-microm wavelength is studied experimentally. For the ion desorption, an in-house built Yb : YAG-pumped optical parametric oscillator (OPO) infrared (IR) laser has been coupled with AP MALDI ion source interfaced to an ion trap mass spectrometer (MS). It has been shown that water is primarily responsible for ion generation in water/glycerol samples, while glycerol increases the solution viscosity and decreases the water evaporation rate and sample losses. In contrast to AP UV-MALDI, the electric field in the case of AP IR-MALDI does not assist in ion production. It was found that the absence of the electrical field provides the optimum ionization condition both for water and water/glycerol liquid samples at the 3-microm laser irradiation. A two-stage ion formation mechanism, which includes the initial emission of microdroplets and release of molecular ions at the second stage, can explain the experimentally observed ion signal dependencies upon the voltage applied between MS inlet and the MALDI sample plate. Postionization using additional corona discharge APCI increases the observed signal by approximately 50%, which indicates that some portion of the analyte is desorbed in the form of neutral molecules.     

Paper spray ionization with ion mobility spectrometry at ambient pressure

A paper spray ion source was combined with a drift tube operating at ambient pressure for mobility measurements of ions derived from pharmaceutical solutions. Paper spray ionization with solvent alone resulted in a mixture of ions convolved to a single peak with a reduced mobility of 2.19 cm²/Vs in the mobility spectrum. These were mass-identified principally as m/z 157, (MeOH)₂(HCOOH)₂H⁺ and m/z 129, (MeOH)₄(H₂O)H⁺ while pharmaceuticals with nitrogen bases formed MH⁺ product ions. The duration of response was governed by the volume of liquid added to the paper source and was limited by evaporation of solvent in gas at 58 °C venting the drift tube. Quantitative variation was attributed in part to morphologic changes in the tip of the paper spray source. This was associated with mass flow in the electrical discharge and not due alone to cycles of wetting and drying of the paper. Mobility spectra of chlorpromazine in urine, exhibited a single product ion peak and linear response was 30 to 500 ng with an estimated limit of detection of 1.5 ng. Ion flux could be prolonged by continuous addition of liquid and findings portend a combination of paper spray ionization IMS with paper chromatography.     

Matrix effect on the determination of synthetic corticosteroids and diuretics by liquid chromatography-tandem mass spectrometry

This work presents a high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) procedure for selective and reliable screening of corticosteroids and diuretics in human urine. Sample preparation included the extraction, evaporation of the organic extract under nitrogen, and solution of the dry residue. The extract was analyzed by HPLC combined with tandem mass spectrometry using electro-spraying ionization at atmospheric pressure with negative ion recording. The mass spectra of all compounds were recorded, and the characteristic ions, retention times, and detection limits were determined. The procedure was validated by evaluating the degree of the matrix suppression of ionization, extraction of analytes from human biological liquid, and the selectivity and specificity of determination.     

Ionspray microchip

An ionspray microchip is introduced. The chip is based on the earlier presented nebulizer microchip that consists of glass and silicon plates bonded together. A liquid inlet channel, nebulizer gas inlet, and nozzle are etched on the silicon plate and a platinum heater is integrated on the glass plate. The nebulizer microchip has been previously used in atmospheric pressure chemical ionization, atmospheric pressure photoionization, sonic spray ionization, and thermospray ionization modes. In this work we show that the microchip can be operated also in ionspray mode by introducing high voltage to the silicon plate of the microchip. The effects of operation parameters (voltage, nebulizer gas pressure, sample solution flow rate, solvent composition, and analyte concentration) on the performance of the ion spray microchip were studied. Under optimized conditions the microchip provides efficient ionization of small and large compounds and good quantitative performance. The feasibility of the ion spray microchip in liquid chromatography/mass spectrometry (LC/MS) was demonstrated by the analysis of tryptic peptides of bovine serum albumin. Copyright © 2010 John Wiley & Sons, Ltd.     

An evaluation of atmospheric pressure ionization techniques for the analysis of N-Methyl carbamate pesticides by liquid chromatography mass spectrometry

Atmospheric pressure ionization (API) techniques are evaluated for the mass spectral analysis of N-methyl carbamate pesticides. Atmospheric pressure chemical ionization (APCI) using a heated nebulizer interface provided both protonated molecules and abundant, characteristic fragment ions. With ion spray (ISP; pneumatically assisted electrospray ionization), which utilizes a milder “ion evaporation” process, primarily protonated molecules were obtained, although fragment ions similar to those observed in APCI could be induced by variation of the API orifice voltage. Product ion spectra of ISP-derived protonated molecules, generated by tandem mass spectrometry using collision-induced dissociation, are also presented. The APCI and ISP spectra of the carbamates are compared to those obtained with a thermospray interface and also to their electron ionization and methane CI spectra obtained with a particle beam interface. For all four interfaces, combined liquid chromatography mass spectrometry methods using conventional (4.6 mm i.d.) columns are described for the separation and detection of pesticide mixtures. These methods are applied to the confirmatory analysis of three representative carbamate pesticides, spiked at the 0.1-ppm level in green peppers. For those carbamates amenable to gas chromatography mass spectrometry, comparative results are presented.     

A pulsed triple ionization source for sequential ion/ion reactions in an electrodynamic ion trap

A pulsed triple ionization source, using a common atmosphere/vacuum interface and ion path, has been developed to generate different types of ions for sequential ion/ion reaction experiments in a linear ion trap-based tandem mass spectrometer. The triple ionization source typically consists of a nano-electrospray emitter for analyte formation and two other emitters, an electrospray emitter and an atmospheric pressure chemical ionization emitter or a second nano-electrospray emitter for formation of the two different reagent ions. The three emitters are positioned in a parallel fashion close to the sampling orifice of the tandem mass spectrometer. The potentials applied to each emitter are sequentially pulsed so that desired ions are generated separately in time and space. Sequential ion/ion reactions take place after analyte ions of interest and different set of reagent ions are sequentially injected into a linear ion trap, where axial trapping is effected by applying an auxiliary radio frequency voltage to the end lenses. The pulsed triple ionization source allows independent optimization of each emitter and can be readily coupled to any atmospheric pressure ionization interface with no need for instrument modifications, provided the potentials required to transmit the ion polarity of interest can be synchronized with the emitter potentials. Several sequential ion/ion reactions examples are demonstrated to illustrate the analytical usefulness of the triple ionization source in the study of gas-phase ion/ion chemistry.     

Characterization of triglycerides in vegetable oils by silver-ion packed-column supercritical fluid chromatography coupled to mass spectroscopy with atmospheric pressure chemical ionization and coordination ion spray

Characterization of triglycerides in vegetable oils was achieved by silver-ion packed-column supercritical fluid chromatography (SI-pSFC) with mass spectrometric detection. Hyphenation was made using commercially available liquid chromatography-mass spectrometry (LC-MS) interfaces without any modification. A make-up fluid was delivered through a T-piece placed before or after the SFC restrictor by means of a high pressure pump. Atmospheric pressure chemical ionization (APCI) and coordination ion spray (CIS) with silver ions were used as ionization modes. Compared to UV detection, the sensitivity was increased by a factor of 100. Both ionization modes are generating similar structural information. Molecular ions [M-H]+ or [M-Ag(-)] are observed in the mass spectra with exception of the saturated triglycerides for which only CIS gives intense molecular ions. The position at which the fatty acids are esterified to the glycerol backbone can be elucidated by pSFC-APCI although it remains speculative whether this is valid for highly unsaturated triglycerides because reference compounds are not available to proof this.     

The determination of glycopeptides by liquid chromatography/mass spectrometry with collision-induced dissociation

Glycopeptides derived from ribonuclease B and ovomucoid have been subjected to collision-induced dissociation (CID) in the second quadrupole of a triple quadrupole mass spectrometer. Doubly charged parent ions gave predictable fragmentation that yielded partial sequence information of the attached oligosaccharide as Hex and HexNAc units. Common oxonium ions are observed in the product ion mass spectra of the glycopeptides that correspond to HexNAc⁺ (m/z 204) and HexHexNAc⁺ (m/z 366). A strategy for locating the glycopeptides in the proteolytic digest mixtures of glycoproteins by ions spray liquid chromatography mass spectrometry (LC/MS) is described by utilizing CID in the declustering region of the atmospheric pressure ionization mass spectrometer to produce these characteristic oxonium ions. This LC/CID/MS approach is used to identify glycopeptides in proteolytic digest mixtures of ovomucoid, asialofetuin, and fetuin. LC/CID/MS in the selected ion monitoring mode may be used to identify putative glycopeptides from the proteolytic digest of fetuin.     

An atmospheric pressure ion lens that improves nebulizer assisted electrospray ion sources

An atmospheric pressure ion lens improves the performance and ease of use of a nebulizer assisted electrospray (ion spray) ion source. The lens is comprised of an oblong-shaped stainless steel ring attached to an external high voltage power supply. The lens is located near the tip of the conductive sprayer, and is maintained at a potential less than that of the sprayer. The ion lens improves the shape of the equipotential lines in the vicinity of the sprayer tip. This lens gives approximately a 2-fold reduction in the signal RSD, a 2-fold increase in the ion signal, an increase in the number of multiply charged ions, and a much broader range of usable sprayer positions.     

Unexpected observation of ion suppression in a liquid chromatography/atmospheric pressure chemical ionization mass spectrometric bioanalytical method

Ion suppression is a well-known phenomenon in electrospray ionization (ESI) mass spectrometry. These suppression effects have been shown to adversely affect the accuracy and precision of quantitative bioanalytical methods using ion spray. Such suppression effects have not been as well defined in atmospheric pressure chemical ionization (APCI) and there is some debate whether these effects actually occur in the ionization process using APCI. Here an example is described where clear ion suppression was observed during studies on a model compound and three metabolites using APCI liquid chromatography/tandem mass spectrometry (LC/MS/MS).     

Laserspray ionization (LSI) ion mobility spectrometry (IMS) mass spectrometry

A simple device is described for desolvation of highly charged matrix/analyte clusters produced by laser ablation leading to multiply charged ions that are analyzed by ion mobility spectrometry-mass spectrometry. Thus, for example, highly charged ions of ubiquitin and lysozyme are cleanly separated in the gas phase according to size and mass (shape and molecular weight) as well as charge using Tri-Wave ion mobility technology coupled to mass spectrometry. This contribution confirms the mechanistic argument that desolvation is necessary to produce multiply charged matrix-assisted laser desorption/ionization (MALDI) ions and points to how these ions can be routinely formed on any atmospheric pressure mass spectrometer.     

Evolution of instrumentation for the study of gas-phase ion/ion chemistry via mass spectrometry

The scope of gas-phase ion/ion chemistry accessible to mass spectrometry is largely defined by the available tools. Due to the development of novel instrumentation, a wide range of reaction phenomenologies has been noted, many of which have been studied extensively and exploited for analytical applications. This perspective presents the development of mass spectrometry-based instrumentation for the study of the gas-phase ion/ion chemistry in which at least one of the reactants is multiply charged. The instrument evolution is presented within the context of three essential elements required for any ion/ion reaction study: the ionization source(s), the reaction vessel or environment, and the mass analyzer. Ionization source arrangements have included source combinations that allow for reactions between multiply charged ions of one polarity and singly charged ions of opposite polarity, arrangements that enable the study of reactions of multiply charged ions of opposite polarity and, most recently, arrangements that allow for ion formation from more than two ion sources. Gas-phase ion/ion reaction studies have been performed at near atmospheric pressure in flow reactor designs and within electrodynamic ion traps operated in the mTorr range. With ion trap as a reaction vessel, ionization and reaction processes can be independently optimized and ion/ion reactions can be implemented within the context of MSn experiments. Spatial separation of the reaction vessel from the mass analyzer allows for the use of any form of mass analysis in conjunction with ion/ion reactions. Time-of-flight mass analysis, for example, has provided significant improvements in mass analysis figures of merit relative to mass filters and ion traps.     

Discrimination of isomers by liquid ionization mass spectrometry with techniques of collisional activation and adduct ion formation

Liquid ionization mass spectrometry is a soft ionization technique used with liquid samples under atmospheric pressure. It facilitates the handling of reagents and the observation of ion–molecule reactions in the ion source. The differentiation of isomers by characteristic fragment ions, for example those resulting from asymmetrical cleavage of a cyclobutane ring, and by molecular adduct ion formation was studied. The samples studied were cyclobutane derivatives, alkyl 4-(3-oxo-3-pIienyl-l-aIkenyl)benzoate dimers, and reagents having two functional groups were used to produce adduct ions to clarify the difference between isomers. The reagents act on a sample molecule at two functional groups to form hydrogen bonds. Some correlations were observed between the structure of the sample and the relative abundances of molecular adduct ions and also fragment ions produced by collisionally activated dissociation.     

Rapid detection of drugs in biofluids using atmospheric pressure chemi/chemical ionization mass spectrometry

We have demonstrated that, with simple pH adjustment, volatile drugs such as methamphetamine, amphetamine, 3,4‐methylenedioxymethamphetamine (MDMA), ketamine, and valproic acid could be analyzed rapidly from raw biofluid samples (e.g. urine and serum) without dilution, or extraction, using atmospheric pressure ionization. The ion source was a variant type of atmospheric pressure chemical ionization (APCI) that used a dielectric barrier discharge (DBD) to generate the metastable helium gas and reagent ions. The sample solution was loaded in a disposable glass pipette, and the volatile compounds were purged by nitrogen gas to be reacted with the metastable helium gas. The electrodes of the DBD were arranged in such a way that the generated glow discharge was confined within the discharge tube and was not exposed to the analytes. A needle held at 100–500 V was placed between the ion‐sampling orifice and the discharge tube to guide the analyte ions into the mass spectrometer. After pH adjustment of the biofluid sample, the amphiphilic drugs were in the form of a water‐insoluble oil, which could be concentrated on the liquid surface. By gentle heating of the sample to increase the evaporation rate, rapid and sensitive detection of these drugs in raw urine and serum samples could be achieved in less than 2 min for each sample. Copyright © 2009 John Wiley & Sons, Ltd.     

Recent developments of miniature ion trap mass spectrometers

The recent development of miniature ion trap mass spectrometer systems in the last ten years is reviewed in this paper. These instruments adopt different atmospheric pressure interfaces (APIs), which are membrane inlets (MIs), discontinuous atmospheric pressure interface (DAPI) and continuous atmospheric pressure interface (CAPI).     

An electrospray ion source for magnetic sector mass spectrometers

Electro spray mass spectra of carbonic anhydrase (MW ～ 29000) and ovalbumin (MW ～ 45000) were obtained on a double focusing magnetic secter mass spectrometer by using a single stage of mechanical pumping in the interface between atmospheric pressure and high vacuum. Full scan spectra of lysozyme were recorded on 15 fmoles consumed. In addition, accurate mass measurement was demonstrated for peptides and proteins, and resolution in excess of 10,000 (m /△m, 10% valley) was observed. These results clearly show that high performance magnetic sector mass spectrometers can be advantageously interfaced to an atmospheric pressure electrospray ion source.     

Investigation of neuroleptics and other aromatic compounds by laser-based ion mobility mass spectrometry

Laser-based ion mobility (IM) spectrometry was used for the detection of neuroleptics and PAH. A gas chromatograph was connected to the IM spectrometer in order to investigate compounds with low vapour pressure. The substances were ionized by resonant two-photon ionization at the wavelengths λ?=?213 and 266 nm and pulse energies between 50 and 300 μJ. Ion mobilities, linear ranges, limits of detection and response factors are reported. Limits of detection for the substances are in the range of 1–50 fmol. Additionally, the mechanism of laser ionization at atmospheric pressure was investigated. First, the primary product ions were determined by a laser-based time-of-flight mass spectrometer with effusive sample introduction. Then, a combination of a laser-based IM spectrometer and an ion trap mass spectrometer was developed and characterized to elucidate secondary ion–molecule reactions that can occur at atmospheric pressure. Some substances, namely naphthalene, anthracene, promazine and thioridazine, could be detected as primary ions (radical cations), while other substances, in particular acridine, phenothiazine and chlorprothixene, are detected as secondary ions (protonated molecules). The results are interpreted on the basis of quantum chemical calculations, and an ionization mechanism is proposed.     

Effect of eluent on the ionization efficiency of flavonoids by ion spray, atmospheric pressure chemical ionization, and atmospheric pressure photoionization mass spectrometry.

The effect of nine different eluent compositions on the ionization efficiency of five flavonoids was studied using ion spray (IS), atmospheric pressure chemical ionization (APCI), and the novel atmospheric pressure photoionization (APPI), in positive and negative ion modes. The eluent composition had a great effect on the ionization efficiency, and the optimal ionization conditions were achieved in positive ion IS and APCI using 0.4% formic acid (pH 2.3) as a buffer, and in negative ion IS and APCI using ammonium acetate buffer adjusted to pH 4.0. For APPI work, the eluent of choice appeared to be a mixture of organic solvent and 5 mM aqueous ammonium acetate. The limits of detection (LODs) were determined in scan mode for the analytes by liquid chromatography/mass spectrometry using IS, APCI and APPI interfaces. The results show that negative ion IS with an eluent system consisting of acidic ammonium acetate buffer provides the best conditions for detection of flavonoids in mass spectrometry mode, their LODs being between 0.8 and 13 microM for an injection volume of 20 microl.     

A linear ion trap mass spectrometer with versatile control and data acquisition for ion/ion reactions

A linear ion trap (LIT) with electrospray ionization (ESI) for top-down protein analysis has been constructed. An independent atmospheric sampling glow discharge ionization (ASGDI) source produces reagent ions for ion/ion reactions. The device is also meant to enable a wide variety of ion/ion reaction studies. To reduce the instrument's complexity and make it available for wide dissemination, only a few simple electronics components were custom built. The instrument functions as both a reaction vessel for gas-phase ion/ion reactions and a mass spectrometer using mass-selective axial ejection. Initial results demonstrate trapping efficiency of 70% to 90% and the ability to perform proton transfer reactions on intact protein ions, including dual polarity storage reactions, transmission mode reactions, and ion parking.