Development of a new matrix based on a silicone ladder polymer for ion-sensing membranes.

A silicone ladder-type polymer was successfully utilized for a matrix of an ion sensing membrane to fabricate an ion-sensitive field-effect transistor. An ion sensing membrane was readily fabricated by mixing a silicone ladder-type oligomer with a quaternary ammonium salt, casting onto the gate of the field-effect transistor, and polymerizing with heating. Since no acid catalysts were needed to prepare the ion sensing membrane, it was possible to keep the quaternary ammonium salt in the matrix without decomposition. The ion-sensitive field-effect transistor based on the silicone ladder-type polymer and the quaternary ammonium salt showed a linear response with a slope of -58.1 mV decade(-1) very close to the theoretical Nernstian response over an NO3- range between 3.0 x 10(-6) and 1.0 x 10(-1) M. The time required to reach 90% total response was within 5 s, when the NO3- concentration was changed from 1.0 x 10(-3) to 3.0 x 10(-3) M. The newly fabricated ion-sensitive field-effect transistors have kept their original sensitivity for more than half a year.     

杯芳烃银离子敏感场效应晶体管传感器

报道了硫醚取代的杯「４」芳烃化合物的合成,以此化合物为敏感材料,研制了聚氯乙烯膜的银离子敏感场效应晶体管传感器。Ａｇ＾＋－ＩＳＦＥＴ传感器对银离子表现出了优良的能斯特呼应,响应斜率为５８ｍＶ／ｐＡｇ,同时该传感器对碱金属、碱土金属及过渡金属离子有极高的选择性,在１０＾－２－１０＾－５ｍｏｌ／Ｌ范围内有良好的线性关系,检测限为１０＾－５．４ｍｏｌ／Ｌ。     

Development of a selective optical sensor for Cr(VI) monitoring in polluted waters

An optical sensor is described for the sensitive and selective determination of the Cr(VI) ion in aqueous solutions. The optode membrane is prepared by incorporating Aliquat 336 as an ionophore and a chromoionophore (4',5'-dibromofluorescein octadecyl ester) in a poly(vinyl chloride) (PVC) membrane containing ortho-nitrophenyloctyl ether (o-NPOE) as a plasticizer. The response to Cr(VI) is indicated by co-extraction of the target species and of hydrogen ions into the bulk of the membrane yielding large absorbance changes which can easily be measured in the visible spectral range. The optode membrane shows a reversible response in the concentration range of 1.1x10(-5)-1.0x10(-3) M and has been shown to be more selective towards the HCrO4(-) ion than other anions with a selectivity pattern HCrO4(-) > SCN- approximately = ClO4(-) > NO3(-) approximately = I- approximately = NO2(-) > H2PO4(-) approximately = Cl- approximately = SO4(2-). The sensing method developed has successfully been applied to the determination of Cr(VI) in spiked river water as well as in electroplating rinse waters.     

Microfluidic polymer chip integrated with an ISFET detector for cationic surfactant assay in dental rinses.

A cationic surfactant ion-selective field-effect transistor (cationic surfactant-ISFET) has been developed based on the tetraphenylborate derivative known as sodium tetrakis[3,5-bis(trifluoromethyl)phenyl]borate. The cationic surfactant-ISFET shows an almost Nernstian response to tetradecyldimethylbenzylammonium chloride (Zephiramine) over a concentration range between 1.0 x 10(-6) M and 1.0 x 10(-3) M, with a slope of 58.5 +/- 1.7 mV/decade. The cationic surfactant-ISFET can be used over a range of pH values, between pH 3 and 9. The cationic surfactant-ISFET shows excellent selectivity for Zephiramine over small inorganic cations, but shows similar selectivity for other cationic surfactants, such as hexadecyltrimethylammonium and stearyltrimethylammonium ions. A microfluidic polymer chip was integrated with the cationic surfactant-ISFET, and this was fabricated using polystyrene plates and stainless wires as a template for the channel. Cationic surfactant-ISFETs used in a batch system and microchips integrated with cationic surfactant-ISFETs showed very similar performance in terms of low detection limits, slope sensitivity and the stability of the potential response. The microfluidic polymer chip was then applied to the determination of cationic surfactants in dental rinses.     

Bis-dimethylaminobenzaldehyde Schiff-base cobalt(II) complex as a neutral carrier for a highly selective iodide electrode.

A new solvent polymeric membrane electrode based on N,N'-bis-(dimethylaminobenzaldehyde)-glycine cobalt(II) [Co(II)-BDMABG] as a neutral carrier is described, which displays a preferential potentiometric response to iodide ion and an anti-Hofmeister selectivity sequence in the following order: I- > ClO4- > Sal- > SCN- > NO2- > Br- > NO3- > Cl- > SO3(2-) > SO4(2-). The electrode exhibits a near-Nernstian potential linear range of 9.0 x 10(-7)-1.0 x 10(-1) M with a detection limit of 6.8 x 10(-7) M and a slope of -53.0 mV/decade in pH 2.0 of a phosphate buffer solution at 20 degrees C. The response mechanism is discussed in view of the A.C. impedance technique and the UV spectroscopy technique. The electrode was successfully applied to the determination of iodide in Jialing River and Spring in Jinyun Mountains with satisfactory results.     

Highly selective thiocyanate electrode based on bis-[N-(2-hydroxyethyl)salicylaldimino]copper(II) complex as a neutral carrier.

A novel selective thiocyanate electrode of a PVC membrane based on bis-[N-(2-hydroxyethyl)salicylaldimino]copper(II) [Cu(II)-BNSDM] as a neutral carrier is reported. The selectivity sequence of this electrode is as follows: SCN- > ClO4- > I- > Sal- > Br- > NO2- > Cl- > NO3- > H2PO4- > SO4(2-), which is an anti-Hofmeister selectivity sequence. The electrode exhibits a Nernstian potential linear range to thiocyanate from 1.0 x 10(-1) to 6.0 x 10(-6) mol/L with a detection limit of 2.0 x 10(-6) mol/L and a slope of (-59.0+/-0.2)mV/decade in pH 5.0 of a phosphate buffer solution at 25 degrees C. Electrochemical impedance spectroscopy (EIS) and UV spectroscopy techniques were performed to understand the response mechanism of the electrode. The electrode had the advantage of simplicity, high selectivity, fast response and low detection limit compared with the other electrode, which had been reported before. The electrode had been applied to wastewater analysis, and the obtained results were satisfactory.     

Triethylene glycol ether end-grafted carbosilane dendrimer: a potential ionophore for potassium ion recognition.

The performance of a newly synthesized carbosilane dendrimer bearing four triethylene glycol ether (TEG) units, Si(CH2CH2CH2Si(Me)2CH2CH2CH2(OCH2CH2)3Me)4 (1), as ionophores in ion-selective electrodes has been investigated. Optimization of the plasticized polyvinyl chloride membrane composition has produced electrodes that exhibit a Nernstian response for potassium ions. The best general characteristics exhibited by the electrodes were found when the membrane composition ratio of DPE:1:NaTPB:PVC 60:3:2:35 (wt%) was used. The response of the electrode was linear with a Nernstian slope of 58.3 mV/decade over the K+ ion concentration range of 1.9x10(-7) to 1.0x10(-1) M with a detection limit of 3.1x10(-7) M. The response time to achieve a 95% steady potential for the K+ concentration ranging from 1.0x10(-1) to 1.0x10(-8) M was less than 10 s, and it was found that the electrode is suitable for use within a pH range of 5.5-8.5. The selectivity coefficients (log KPotK+,Mn+)), which were determined by the fixed interference method, showed good selectivity for K+ against most of the interfering cations. The influence of this selective ion-binding behavior using electrospray ionization time-of-flight (ESI-TOF) mass spectrometric studies is discussed.     

Phosphate ion-sensitive coated-wire/field-effect transistor electrode based on cobalt phthalocyanine with poly(vinyl chloride) as the membrane matrix

An ion-selective coated-wire/field-effect transistor electrode responding to dihydrogenphosphate is described. The device consists of a coated-platinum wire electrode connected to the gate of a conventional field-effect transistor. Cobalt phthalocyanine is used as ion-exchange electroactive substance and poly(vinyl chloride) as the membrane matrix. The characteristics of the device are investigated and its response is studied by two methods, the linear dependence of the square root of the drain current in the saturated region on the logarithm of ion activity for sodium dihydrogenphosphate, and the dependence of the gate-source potential on the logarithm of ion activity of the same ion. A linear response is obtained in the range of ion activity 10^?5-10^?1 mol dm^?3 and the response slope is 45 mV per decade change of H₂PO₄^? ion activity; the selectivity coefficients are discussed.     

Ion pairing between Cl- or ClO4- and alkali metal complexes of ionophore antibiotics in organic solvents: a multinuclear NMR and FT-IR study

The extent of ion pairing in chloride and perchlorate salts was studied by measurement of the Cl- and ClO4- resonances and the observation of the perchlorate stretching frequency by use of nuclear magnetic resonance (NMR) spectroscopy and Fourier transform infrared spectroscopy (FT-IR), respectively, for a variety of ionophores in various solutions and in large unilaminar vesicles (LUVs). The NMR line widths of chloride and perchlorate were larger in solutions containing the neutral ionophores valinomycin (Val) and nonactin (Non) than in solutions containing the negatively charged ionophores nigericin (Nig), lasalocid (Las), and monensin (Mon). The viscosity-corrected perchlorate NMR line widths in solutions containing Val and Las were significantly negatively correlated (r2 > or = 0.99) with the dielectric constant of the solvent. Solvents with low dielectric constants favored ion pair formation. From methanolic solutions containing the Li+, Na+, K+, and Cs+ salts of Cl- and ClO4-, it was determined that the cation with the highest selectivity for the ionophore affords the most ion pairing. A decrease in pH from 7 to 3 had no significant effect on the NMR line widths of chloride and perchlorate in methanolic solutions containing Val, whereas a similar decrease in pH in a methanolic solution containing Mon caused a 2-fold increase in the line widths. The FT-IR difference spectrum of KClO4 in a methanolic solution containing Val showed splitting at the perchlorate stretching frequency. No band splitting was observed in the FT-IR difference spectrum of KClO(4) in methanolic solutions containing Las. The efflux of 35Cl in LUVs containing the neutral ionophore Val followed first-order kinetics with an efflux constant of 1.70 x 10(-3) x min(-1), as determined by 35Cl NMR spectroscopy. The induction of increased membrane permeability in LUVs by the ionophore was determined to be negligible for Val and Nig by fluorescence spectroscopy.     

Mercury(II) ion-selective electrodes based on heterocyclic systems

Mercury ion-selective electrodes (ISEs) were prepared with a polymeric membrane based on heterocyclic systems: 2-methylsulfanyl-4-(4-nitro-phenyl)-l-p-tolyl-1H-imidazole (I) and 2,4-diphenyl-l-p-tolyl-1H-imidazole (II) as the ionophores. Several ISEs were conditioned and tested for the selection of common ions. The electrodes based on these ionophores showed a good potentiometric response for Hg2+ ions over a wide concentration range of 5.0 x 10(5-) - 1.0 x 10(-1)M with near-Nernstian slopes. Stable potentiometric signals were obtained within a short time period of 20 s. The detection limits, the working pH range of the electrodes were 1.0 x 10(-5) M and 1.6-4.4 respectively. The electrodes showed better selectivity for Hg2+ ions over many of the alkali, alkaline-earth and heavy metal ions. Also sharp end points were obtained when these sensors were used as indicator electrodes for the potentiometric titration of Hg2+ ions with iodide ions.     

Fabrication of polymer Langmuir-Blodgett films containing regioregular poly(3-hexylthiophene) for application to field-effect transistor

Semiconducting thin films consisting of regioregular poly(3-hexylthiophene) (RR-PHT) and poly(N-dodecylacrylamide) (pDDA) were constructed by the Langmuir-Blodgett (LB) technique. A mixture of RR-PHT and pDDA spread from a chloroform solution on a water surface forms a stable monolayer, which can be transferred onto solid substrates by the LB method, yielding a well-defined polymer LB film. Surface morphology studies of the LB film indicate that the RR-PHT is dispersed uniformly throughout the surface. The polymer thin film was chemically doped by contacting with FeCl3 acetonitrile solution, and a conductivity of 5.6 S/cm was achieved. Further, the LB film was utilized as the semiconducting film in the field-effect transistor (FET), and mobilities of 2.2 x 10(-4) and 4.4 x 10(-4) cm2 V(-1) s(-1) were obtained by analyzing the saturated and linear regions of the current-voltage characteristic, respectively.     

Suppressed electrostatic ion chromatography with tetraborate as eluent and its application to the determination of inorganic anions in snow and rainwater

Tetraborate is investigated as the eluent ion for suppressed electrostatic ion chromatography (EIC) using a zwitterionic stationary phase. Good separation of a range of inorganic anions (SO4(2-), Cl-, NO3-, Br-, NO3-, ClO3-, and I-) was obtained, with detection limits for highly conducting ions (SO4(2-), Cl-, NO2-, Br- , and NO3-) being less than 8 x 10(-8) M, and for weakly conducting anions (ClO3- and I-) being 2.7 x 10(-7) and 5.8 x 10(-7) M, respectively. Calibration curves were linear up to 1.8 mM of each analyte. Retention times were found to increase with increasing eluent concentration and a linear relationship was observed between log k' and log[Na2B4O7] for all analytes. This behaviour is attributed to the progressive formation of a binary electrical double layer at the surface of the zwitterionic stationary phase. Retention times of analytes could be manipulated by varying the concentration of the eluent. This new suppressed-EIC system was applied to the determination of inorganic anions (SO4(-2) , CI-, NO3-, NO2-, and Br-) in snow and rainwater samples.     

Oxidation of chlorine(III) by hypobromous acid: kinetics and mechanism

The kinetics and mechanism of the chlorine(III)-HOBr reaction were studied by the stopped-flow method under acidic conditions, pH 1.0-3.0, in 1.0 M NaClO(4) and at 25.0 degrees C. The overall redox process occurs in two consecutive steps via the formation of the BrClO(2) intermediate. The electron transfer reactions are coupled with bromine hydrolysis, the formation of the tribromide ion, and the protolytic equilibrium of chlorine(III). On the basis of simultaneous evaluation of the kinetic traces, the following rate constants were obtained for the redox steps: HClO(2) + HOBr right harpoon over left harpoon BrClO(2) + H(2)O, k(3) = (3.34 +/- 0.02) x 10(4) M(-1) s(-1), k(-3) = (3.5 +/- 1.3) x 10(3) s(-1); BrClO(2) + ClO(2)(-)<==>2ClO(2) + Br(-), k(4) = (2.9 +/- 1.0) x 10(7) M(-1) s(-1). The second step was practically irreversible under the conditions applied, and the value of k(-4) could not be determined. The equilibrium constant for the formation of BrClO(2), K(3) = 9.5 M(-1), was calculated from the kinetic results, and it was confirmed that this species is a very powerful oxidant. The redox potential was also estimated for the BrClO(2) + e(-) = Br(-) + ClO(2) reaction: epsilon(0) approximately 1.70 V.     

Lead-selective poly(vinyl chloride) membrane electrodes based on acyclic dibenzopolyether diamides

Lipophilic acyclic dibenzopolyether diamides, 12 kinds, have been designed to prepare solvent polymeric membrane ion-selective electrodes (ISEs) for Pb(2+). The ionophores include 1,5-bis[2-(N,N-dialkylcarbamoylmethoxy)phenoxy]-3-oxapentanes1-4, 1,5-bis[2-(N,N-dialkylcarbamoylpentadecyloxy)phenoxy]-3-oxapentanes 5-8, and 1,2-bis[2-(2'-N,N-dialkylcarbamoylpentadecyloxy)phenoxy]ethanes 9-12. Linear response concentration range of the ISE based on 9 is 3 x 10(-2) - 1 x 10(-6) M of Pb(2+) (average slope = 28.5 mV decade(-1)). Potentiometric selectivities of the ISEs based on 1-12 for Pb(2+) over other heavy metal cations, alkali metal cations, and alkaline earth metal cations have been assessed. These ISEs exhibit remarkably high selectivities for Pb(2+) relative to heavy metal cations, such as Cu(2+), Fe(2+), and Ni(2+), the selectivity coefficients (K(Pot)(Pb,Cu)) being 5 x 10(-5) - 6 x 10(-5) for 1-4 and ca. 6 x 10(-4) for 9. For the Pb(2+) selectivities over alkali metal cations, such as Na(+) and K(+), 9 which has an ethylene glycol spacer and a N,N-diethyl group is superior to other dibenzopolyether diamide ionophores 1-8 and 10-12.     

Potentiometric determination of silver(I) by selective membrane electrode based on derivative of porphyrin.

The performance of silver metal complexes with meso-tetraphenylporphyrin ([H2T(4-CH3)]PP) as ionophores for ion-selective electrodes was studied. The electrode exhibited linear response with Nernstian slope of 59.2 +/- 1.0 mV per decade within the concentration range of 1.0 x 10(-7)-1.0 x 10(-1) M silver ions. The limit of detection as determined from the intersection of the extrapolated linear segments of the calibration plot, was 1.0 x 10(-7) M. The response time of the electrode was < 10 s over the entire concentration range. The silver-selective electrode exhibited good selectivity for Ag(I) with respect to alkali, alkaline earth and heavy metal ions. The electrodes could be used at least three months without a considerable divergence in their potential. The electrodes are suitable for use in aqueous solutions in a wide pH range of 3.0-9.0. They were used as indicator electrodes in titration of Ag(I) with sodium iodide solution and were successfully applied to direct determination of silver in real samples.     

Preparation of a novel iodide-selective electrode based on iodide-miconazole ion-pair and its application to pharmaceutical analysis.

An iodide-miconazole ion-paired complex was used as a suitable ion-exchanger for the preparation of a plasticized-PVC membrane electrode. Among different solvent mediators tested, dioctylsebacate exhibited the proper response characteristics, including Nernstian slope of the calibration curve, fast response time and good reproducibility of the emf values. The electrode exhibits a Nernstian slope of -59.8 +/- 0.5 mV decade(-1) for I- ion over a concentration range of 1.0 x 10(-5) - 1.0 x 10(-2) M with a limit of detection of 7.0 x 10(-6) M. The electrode displays a good selectivity for I- with respect to a number of inorganic and organic species. It canbe used over a pH range of 2.5 - 8.5. The membrane sensor was successfully applied to the determination of iodide in water samples and blood serum, as well as in pharmaceutical products such as iodoquinol and thyroxin.     

A comparative study of four 20-membered N2S4-crown ethers as ionophores for polymeric membrane silver

Four 20-membered N2S4-monoazathiacrown ethers have been synthesized and explored as neutral ionophores for Ag+-selective electrodes.Potentiometric responses reveal that the flexibility of the ligands has great effect on the selectivity and sensitivity to Ag+ions.The electrode based on ionophore 9,10,20,25-tetrahydro-5H,12H-tribenzo[b,n,r][1,7,10,16,4,13]tetrathiadiaza cycloicosine6,13-(7H,14H)-dione(C)with 2-nitrophenyl octyl ether(ο-NPOE)as solvent in a poly(vinyl chloride)(PVC)membrane matrix shows a measuring range of 1.0 × 10-6 to 1.0 × 10-3 mol/L with a Nemstian slope of 54.9 ± 0.3 mV/decade.This electrode has high selectivity for Ag+with negligible interference from many other cations and can be used in a wide pH range of 3.6-9.2.     

Kinetic studies of the ClO + ClO association reaction as a function of temperature and pressure

The kinetics of the association reaction of ClO radicals: ClO + ClO + M --> Cl2O2+ M (1), have been investigated as a function of temperature T between 206.0-298.0 K and pressure p between 25-760 Torr using flash photolysis with time-resolved UV absorption spectroscopy. ClO radicals were generated following the photolysis of Br2/Cl2O mixtures in nitrogen diluent gas. Charge coupled device (CCD) detection of time resolved absorptions was used to monitor ClO radicals over a broad wavelength window covering the ClO (A 2Pi<-- X 2Pi) vibronic absorption bands. The high pass filtered ClO absorption cross sections were calibrated as a function of temperature between T = 206.0-320 K, and exhibit a negative temperature dependence. The ClO association kinetics were found to be more rapid than those reported in previous studies, with limiting low and high pressure rate coefficients, in nitrogen bath gas, k0 = (2.78 +/- 0.82) x 10(-32) x (T/300)(-3.99 +/- 0.94) molecule(-2) cm6 s(-1) and k(infinity) = (3.37 +/- 1.67) x 10(-12) x (T/300)(-1.49 +/- 1.81) molecule(-1) cm3 s(-1), respectively, (obtained with the broadening factor F(c) fixed at 0.6). Errors are 2sigma. The pressure dependent ClO association rate coefficients (falloff curves) exhibited some discrepancies at low pressures, with higher than expected rate coefficients on the basis of extrapolation from high pressures (p > 100 Torr). Reanalysis of data excluding kinetic data recorded below p = 100 Torr gave k0 = (2.79 +/- 0.85) x 10(-32) x (T/300)(-3.78 +/- 0.98) molecule(-2) cm6 s(-1) and k(infinity) = (3.44 +/- 1.83)x 10(-12) x (T/300)(-1.73 +/- 1.91) molecule(-1) cm3 s(-1). Potential sources of the low pressure discrepancies are discussed. The expression for k(0) in air bath gas is k0 = (2.62 +/- 0.80) x 10(-32) x (T/300)(-3.78 +/- 0.98) molecule(-2) cm6 s(-1). These results support upward revision of the ClO association rate coefficient recommended for use in stratospheric models, and the stratospheric implications of the results reported here are briefly discussed.     

Development of an EnFET for the detection of organophosphorous and carbamate insecticides

A biosensor for the detection of insecticides based on an ion-sensitive field-effect transistor (ISFET) was developed. The resulting device combines the simplicity of potentiometric sensors and the use of associated electronic systems as powerful tools for the acquisition and the processing of data. The enzyme acetylcholinesterase (AChE) was entrapped in a membrane placed on the gate of the ISFET forming an enzyme field-effect transistor (EnFET). The biosensor is applied to the determination of pesticides in spiked real samples. Organophosphorous and carbamate insecticides were measured with a detection limit of 10(-8) mol L(-1). The measurement is based on the production of hydrogen ions due to the hydrolysis of acetylthiocholine by the enzyme. The resulting local pH change is picked up by the underlying pH-sensitive ISFET and transduced as potential variations. The preparation of the membrane is simple and reproducible. The analysis in spiked real samples was performed in tap water and showed detection limits comparable to those obtained by other researchers.     

Study of a molecular imprinting polymer coated BAW bio-mimic sensor and its application to the determination of caffeine in human serum and urine

A bio-mimic bulk acoustic wave (BAW) sensor was fabricated by coating the caffeine (CAF) template molecular imprinting polymer (MIP). This sensor exhibited high selectivity and a sensitive mass response to CAF. The response range of the sensor was between 5.0 x 10(-9) and 1.0 x 10(-4) M with a detection limit of 5.0 x 10(-9) M at pH 8.0. Recoveries were 96.1-105.6%. Influencing factors were investigated in detail and optimized. When employed to detect real samples, the proposed method proved to be a convenient method with the advantages of high sensitivity, good selectivity and ease of handling.