Properties of cerium-zirconium mixed oxides partially substituted by neodymium: Comparison with Zr-Ce-Pr-O ternary oxides

CeO₂ doped with praseodymium, neodymium and/or zirconium atoms were prepared by coprecipitation and by the sol-gel method. Structural properties were investigated by in situ XRD and Raman spectroscopy while oxygen storage capacity (OSC) was measured by transient CO oxidation. All the compounds, except pure Nd₂O₃, have a fluorite-type structure as well as a Raman band at 560 cm⁻¹ characteristic of the oxygen vacancies involving non-stoichiometric oxides. The lattice parameter under hydrogen, being dependent on the temperature, revealed two reduction mechanisms: one at a low temperature at the surface and another at a high temperature in the bulk. Ce-Nd binary oxides show a strong tendency towards crystallite aggregation, which reduces accessibility to gases and OSC properties. Zirconium improves the thermal resistance to sintering of both Ce-Nd and Ce-Pr oxides. The Zr-Ce-Pr-O followed by Zr-Ce-Nd-O compounds displaying high oxygen mobility at a low temperature, appear to be very promising for practical applications such as OSC materials.     

Evaluation of the acid properties of porous zirconium-doped and undoped silica materials

A series of porous silica and Zr-doped silica molecular sieves, belonging to the MCM-41 and MSU families, were prepared and characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and N₂ adsorption at 77 K. Their acid properties have been evaluated by NH₃-TPD, adsorption of pyridine and deuterated acetonitrile coupled to FT-IR spectroscopy and the catalytic tests of isopropanol decomposition and isomerization of 1-butene. The acidity of purely siliceous solids were, in all cases, very low, while the incorporation of Zr(IV) into the siliceous framework produced an enhancement of the acidity. The adsorption of basic probe molecules and the catalytic behaviour revealed that Zr-doped MSU-type silica was more acidic than the analogous Zr-MCM-41 solid, with a similar Zr content. This high acidity observed in the case of Zr-doped silica samples is due to the presence of surface zirconium atoms with a low coordination, mainly creating Lewis acid sites.     

Zr 改性MnOx/MWCNTs催化剂的结构特征与低温SCR活性

以ZrO（NO₃）₂·2H₂O为前驱体对多壁碳纳米管（MWCNTs）进行了改性并负载MnO_x制备了MnO_x/ZrO₂/MWCNTs 催化剂. 考察了Zr 对催化剂低温选择性催化还原（SCR）反应活性的影响,并通过多种分析手段对催化剂的结构进行了表征. 结果表明Zr 的添加对催化剂的低温SCR活性具有显著的促进作用,当Zr 负载量为30%时,催化剂活性最佳. X射线衍射（XRD）、拉曼（Raman）光谱、透射电镜（TEM）、N₂吸附-脱附的表征结果分析表明,适量的Zr 改性促进了MnO_x在载体表面的分散,增强金属氧化物与MWCNTs 之间的作用,也能增加催化剂的比表面积、孔容和孔径. X 射线光电子能谱（XPS）、H₂程序升温还原（H₂-TPR）和NH₃程序升温脱附（NH₃-TPD）的分析结果则显示,Zr 能提高催化剂表面化学吸附氧浓度,促进Mn³⁺转化为Mn⁴⁺,从而使催化剂表面的活性位点增多,氧化还原能力增强,同时还提高了催化剂表面酸性位点的数量和强度,促进了NH₃的吸附,是MnO_x/ZrO₂/MWCNTs 催化剂低温SCR活性提高的主要原因.     

乙醛低温绿色合成:焦磷酸锆催化乳酸脱羰反应

以生物基乳酸为原料,焦磷酸锆为催化剂,通过脱羰反应制备乙醛。探讨了模板剂、焙烧温度对催化剂的织构、表面酸碱性以及催化活性的影响规律。以此为基础,进一步揭示了催化剂的表面性质与脱羰反应活性之间的构效关系,发现乳酸脱羰反应由催化剂表面的酸碱位协同催化。和文献报道的相关催化剂比较,该催化剂拥有良好的低温催化活性。此外,在较高液空速、低催化剂用量以及控制低乳酸转化率(40%)下,催化剂连续运行50 h左右后,乳酸转化率及乙醛选择性没有明显变化,表明该催化剂拥有良好的稳定性能。通过反应尾气分析,证实了乙醛的合成主要是通过乳酸脱羰反应途径实现。     

Activated carbon prepared from polyaniline base by K2CO3 activation for application in supercapacitor electrodes

An activated carbon was prepared from a polyaniline base using K₂CO₃ as an activating agent. The morphology, surface chemical composition, and surface area of the as-prepared carbon materials were investigated by scanning electron microscope, X-ray photoelectron spectroscopy, and Brunauer?CEmmett?CTeller measurement, respectively. Electrochemical properties of the as-prepared sample were studied by cyclic voltammetry, galvanostatic charge/discharge, and electrochemical impedance spectroscopy measurements in 6?mol?L^?1 KOH aqueous solution. Compared with the non-activated carbon, activated carbon showed superior capacitive performance. The activation carbon presented a high specific gravimetric capacitance of 210?F?g^?1. The good electrochemical performance of the activated carbon was ascribed to well-developed micropores, high surface area, the presence of nitrogen and oxygen functional groups, and larger pore volume.     

DBD Surface Modification of Polymers in Relation to the Spatial Distribution of Reactive Oxygen Species

The homogeneity of a helium dielectric barrier discharge, working at atmospheric pressure and containing oxygen as contaminant, is assessed by mapping the spatial distribution of oxygen metastable atoms in relation to the uniformity of surface properties. Tunable diode laser absorption spectroscopy is used to monitor the time evolution of the absorption coefficient corresponding to the oxygen metastable atoms on the 3⁵S₂ level, as a function of the laser absorbing path, whereas bi-dimensional Abel transform is used to obtain local information on the space distribution of the metastable atoms in the discharge. The radial distribution of the surface properties is investigated using atomic force microscopy, contact angle measurement and X-ray photoelectron spectroscopy. The results show that the oxygen metastables density has complex space–time behavior, and the spatial distribution of the reactive species yields specific radial profile of the surface properties of a polymer film depending on the treatment time.     

Synthesis,characterization, and functionalization of zirconium tungstate (ZrW2O8) nano‐rods for advanced polymer nanocomposites

Nanomaterials based on zirconium tungstate (ZrW₂O₈) exhibit numerous outstanding properties that make them ideal candidates for the development of high‐performance composites. Low coefficient of thermal expansion for advanced materials is a promising direction in the field of insulating nanocomposites. However, the agglomeration of zirconium tungstate (ZrW₂O₈)‐based nanomaterials in the polymer matrix is a limiting factor in their successful applications, and studies on surface functionalization ZrW₂O₈ for advanced nanocomposites are very limited. In this work, ZrW₂O₈ nano‐rods were synthesized using a hydrothermal method and subsequently functionalized in a solvent‐free aqueous medium using dopamine. Both pristine and functionalized nano‐rods were thoroughly characterized using Fourier transform infrared spectroscopy, Raman spectroscopy, thermogravimetric analysis, X‐ray diffraction, Scanning Electron Microscopy (SEM), and transmission electron microscopy techniques, which confirmed the successful functionalization of the nanomaterials. Polymer nanocomposites were also prepared using epoxy resin as a model matrix. Polymer nanocomposites with functionalized ZrW₂O₈ nano‐rods exhibited low coefficient of thermal expansion and enhanced tensile properties. The improved properties of the nanocomposites render them suitable for electronic applications. Copyright © 2017 John Wiley & Sons, Ltd.     

Structures and oxygen storage/release capacities of Ce_xZr_(1-x)O_2: Effects of Zr content and preparation method

Ceria-zirconia solid solution has been prepared by the urea grind combustion and citric acid sol-gel methods for catalytic applications as oxygen storage/release materials in this study. The properties and oxygen storage/release capacities of samples with different Zr contents were characterized and evaluated by X-ray diffraction(XRD), N_2 adsorption, scanning electron microscopy(SEM), Raman spectroscopy, and insitu CO–CO_2 looping test. The results demonstrate that the samples prepared by two methods are all of excellent lattice [O] release/storage properties and maintain good long-term cycle stability. But the preparation method significantly impacts the homogeneity of samples related to their redox properties and the content of Zr over 20%, which greatly changed the properties of ceria-zirconia solid solutions and caused their changing of crystalline symmetry from cubic to tetragonal. The samples prepared by citric acid solgel method are of more homogeneous particle sizes and higher specific surface areas than that by urea grind combustion method, which is benefit to the oxygen release rather than oxygen storage. The bulk oxygen amount migrated to surface increases with the increasing Zr content, however, the amount of lattice oxygen migration decreases when Zr content is over 20%. When Zr content is 20%, the differences of storage/release capacities from two different preparation methods are reduced at high temperature in the long-term loop reaction.     

Effect of preparative conditions on the surface characteristics of mixed zirconium and titanium oxides

The surface characteristics of mixed zirconium and titanium oxides prepared from different starting materials are investigated. One mode of preparation entailed the use of zirconium sulfate and titanium oxysulfate as starting materials and ammonium hydroxide as precipitating agent. The produced oxides were washed to different extents to obtain samples with different sulfate content. A second preparative mode used zirconium oxychloride and titanous chloride as starting materials also with ammonium hydroxide as precipitating agent. The oxidation of the titanous to the titanic form for these oxides was carried out by means of oxygen gas. Resulting samples were heat treated at 400 °C and 600 °C, and textural characteristics determined from the adsorption of N₂ at 77 K, complemented by infrared and thermal studies. The samples precipitated from the oxychloride and chloride salts of zirconium and titanium, as well as those precipitated from the sulfate and oxysulfate salts and washed free of the sulfate ions displayed quite similar textural characteristics. The unheated samples and those heat-treated at 400 °C were mesoporous, with some microporosity, and relatively large surface areas in the order of 200–300 m²/g. Heat treatment to 600 °C led to a relative decrease in surface area, in the order of 100 m²/g, and to the disappearance of microporosity. The mixed zirconium and titanium oxides with a sulfate content of ≈17% displayed significantly lower surface areas, smaller than 10 m²/g, with a prevalence of micro and mesoporosity. Infrared and thermal studies indicated the presence of differently bounded sulfato groups, which seem to have a blocking effect on the pores, resulting in the observed smaller surface areas.     

Tuning of texture and surface chemistry of carbon xerogels

The influence of different activation processes on the textural and surface chemical properties of carbon xerogels was studied. Carbon xerogels were prepared by the conventional sol-gel approach using resorcinol and formaldehyde; two different pHs of sol-gel processing led to carbon materials with distinct pore size distributions. The materials were subjected to controlled activation by three different methods: activation by oxygen plasma, activation by HNO(3), and activation by diluted air. Treatments with HNO(3) and diluted air created oxygen groups on the external surface as well as inside the pore channels, whereas plasma is more suitable for introducing oxygen groups selectively on the external surface. Nevertheless, it was shown that samples with wider pores can be oxidized to some extent on the pore interiors by plasma. Significant changes in total surface area by air activation were observed.     

Porous phosphate heterostructures containing CdS quantum dots: assembly, characterization and photoluminescence

The synthesis and characterization of cadmium sulphide (CdS) quantum dots, conjugated in a porous phosphate heterostructure functionalized with aminopropyl groups is described. The resulting material has fluorescence properties with maximum emission intensity at 575 nm. The fluorescent materials are not soluble in water and exhibit high stability in aqueous solution in the pH ranges from 2 to 9. Energy dispersive X-ray spectroscopy confirmed the qualitative elemental composition of the synthesized materials and X-ray photoelectron spectra showed a surface S/Cd atomic ratio of 1.09. SEM images show that the materials are amorphous, possessing porous with sizes of several tens nanometres, homogeneous and exhibit a layered morphology. The adsorption–desorption analysis by N₂ at 77 K showed the accessibility of the CdS quantum dots onto the pores of the structure. The CdS quantum dots were stabilized by mercaptopropionic acid and bounded to the host materials by amine groups.     

高介电常数TiO2纳米晶的表面态研究

将钛酸四丁酯和硬脂酸在熔融状态下混合均匀后置于冷水浴中,使其凝固成凝胶,通过控制烧结过程中氧气的含量,成功地制备出粒度均匀、介电性能好的纳米晶TiO2.通过采用X射线光电子能谱和表面光电压谱对纳米晶TiO2表面状态的分析发现,材料表面存在大量的氧空位缺陷,暴露在粒子表面上的主要是一些金属Ti4+.纳米材料的这种表面状态对其极化性质具有重要的影响,使其在接近静态条件下的低频介电常数远大于常规材料的介电常数.     

SYNTHESIS OF HYBRID MESOPOROUS POLYSTYRENE-SILICA MATERIALS WITH NON-SURFACTANT CITRIC ACID AS TEMPLATE VIA SOL-GEL PROCESS

Hybrid mesoporous polystyrene-silica materials were successfully prepared through HCl-catalyzed sol-gelreactions of tetraethyl orthosilicate (TEOS) and triethoxysilyl-functionalized polystyrene obtained via atom transfer radicalpolymerization (ATRP) of styrene, in the presence of citric acid (CA) as non-surfactant template or pore-forming agent andfollowed by ethanol extraction to remove template molecules. The materials were characterized by infrared spectroscopy(IR), N_2 adsorption-desorption measurements, powder X-ray diffraction (XRD), thermogravimetric analysis (TGA) andtransmission electron microscopy (TEM). The results indicate that the materials prepared with 50 wt%-60 wt% templatecontents have average pore sizes of 2-3 nm and large surface areas (ca. 886 m~2/g) as well as high pore volumes (ca.0.53 cm~3/g). The mesoporosity arises from interconnected channels and pores with disordered arrangements. The porediameters and pore volumes increase as the template content is increased. The pore diameters show a little change uponheating at 200℃ overnight. However, the materials do not have good hydrothermal stability.     

Application of modified multiwall carbon nanotubes as a sorbent for zirconium (IV) adsorption from aqueous solution

Modified multiwall carbon nanotubes (MWCNTs) by nitric acid solution were used to investigate the adsorption behavior of zirconium from aqueous solution. Pristine and oxidized MWCNTs were characterized using nitrogen adsorption/desorption isotherm, Boehm’s titration method, thermogravimetry analysis, transmission electron microscopy and Fourier transform infrared spectroscopy. The results showed that the surface properties of MWCNTs such as specific surface area, total pore volume, functional groups and the total number of acidic and basic sites were improved after oxidation. These improvements are responsible for their hydrophobic properties and consequently an easy dispersion in water and suitable active sites for more adsorption of zirconium. The adsorption of Zr(IV) as a function of initial concentration of zirconium, contact time, MWCNTs dosage, HCl and HNO₃ concentration and also ionic strength was investigated using a batch technique under ambient conditions. The experimental results indicated that sorption of Zr(IV) was strongly influenced by zirconium concentrations, oxidized MWCNTs content and acid pH values. The calculated correlation coefficient of the linear regressions values showed that Langmuir model fits the adsorption equilibrium data better than the Freundlich model. Kinetic data of sorption indicated that equilibrium was achieved within 60 min and the adsorption process can be described by the pseudo second-order reaction rate model. Based on the experimental results, surface complexation is the major mechanism for adsorption of Zr(IV) onto MWCNTs. Also, Study on the desorption process of zirconium showed that the complete recovery can be obtained using nitric or hydrochloric acids of 4 M.     

Controllable Synthesis of Inverse Opal TiO2‐x Photonic Crystals and Their Photoelectric Properties

In this study, inverse opal TiO_2‐x photonic crystals (IO‐TiO_2‐x) have been successfully synthesized by a two‐step calcination. The whole synthesis is safe and feasible. Additionly, the reduction degree and the structure of IO‐TiO_2‐x can be precisely controlled. A series of IO‐TiO_2‐x samples with different reduction degree were prepared and characterized. The TEM images show that the obtained samples possess a 3D‐ordered macroporous inverse opal structure. The reduced Ti atoms/oxygen vacancies were confirmed by Raman and XPS spectroscopy. All IO‐TiO_2‐x samples showed better photoelectric properties than those of common TiO₂ which indicates their great potential to be applied to photoelectric fields. The improvement of photoelectric properties is attributed to the efficient electron‐hole separation efficiency induced by moderately reduced Ti atoms/oxygen vacancies. Meanwhile, the 3D‐ordered macroporous inverse opal structure and the band gap are regulated to “capture” more solar energy. This new approach is proven to be a meaningful method to synthesize high‐performance TiO₂ materials.     

Characterization and acidic properties of Al-SBA-15 materials prepared by post-synthesis alumination of a low-cost ordered mesoporous silica

A series of Al-containing SBA-15 type materials with different Si/Al ratio, were prepared by post-synthesis modification of a pure highly ordered mesoporous silica SBA-15 obtained by using sodium silicate as silica source, and amphiphilic block copolymer as structure-directing agent. A high level of aluminum incorporation was achieved, reaching an Si/Al ratio of up to 5.5, without any significant loss in the textural properties of SBA-15. These materials were fully characterized by powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), ²⁷Al NMR spectroscopy, and N₂ adsorption at 77 K. The acid properties of these materials have been evaluated by NH₃-TPD, adsorption of pyridine and deuterated acetonitrile coupled to FTIR spectroscopy. The effective acidity of these materials was evaluated using two catalytic reactions: 2-propanol dehydrogenation and 1-butene isomerization. The adsorption of basic probe molecules and the catalytic behavior revealed an evolution of the acid properties with the Al content. These studies have shown that the Al-SBA-15 materials contain Brønsted and Lewis acid sites with medium acidity which makes them appropriate to be used as acid catalysts in heterogeneous catalysis, catalytic supports, and adsorbents.     

Electrochemical reduction of oxygen on double-walled carbon nanotube modified glassy carbon electrodes in acid and alkaline solutions

The oxygen reduction reaction has been investigated on double-walled carbon nanotube (DWCNT) modified glassy carbon (GC) electrodes in acid and alkaline media using the rotating disk electrode (RDE) method. The surface morphology and composition of DWCNT samples was examined by transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). Aqueous suspensions of DWCNTs were prepared using Nafion and non-ionic surfactant Triton X-100 as dispersing agents. The RDE results indicated that the DWCNT modified GC electrodes are active catalysts for oxygen reduction in alkaline solution. In acid media DWCNT/GC electrodes possess poor electrocatalytic properties for O₂ reduction which indicates lack of metal catalyst impurities in the DWCNT material studied. The oxygen reduction behaviour of DWCNTs was similar to that of multi-walled carbon nanotubes (MWCNTs) observed in our previous studies.     

New process to control hydrolysis step during sol-gel preparation of sulfated zirconia catalysts

Sulfated zirconia catalysts were prepared by sol-gel process using a new method allowing the control of the hydrolysis step of zirconium alkoxides. Prepared samples were characterized by N₂ adsorption (desorption) at 77 K, XRD, chemical analysis of total sulfur and XPS. Catalytic properties have been evaluated in n-butane and n-hexane isomerization reactions. Obtained results show that time necessary for gelation is significant and depends considerably on the nature of the zirconium precursor. Concerning the properties of the solids obtained by this method, it has been noted that the use of the zirconium propoxide led to a better retention of the sulfate species, which improves activity during isomerization reactions. It has been found also that an initial S/Zr molar ratio equal to 0.5 allowed to obtain an optimal sulfur content and a high specific surface area.     

Zirconium oxide complex anchored on boehmite nanoparticles as highly reusable organometallic catalyst for C–S and C–O coupling reactions

Boehmite nanoparticles were prepared by a simple and inexpensive procedure in water using commercially available materials without inert atmosphere. Then, the surface of the boehmite nanoparticles was modified using 3‐mercaptopropyltrimethoxysilane and subsequently zirconium oxide was supported on the modified surface. Zirconium oxide supported on boehmite nanoparticles (Pr.S‐ZrO@boehmite) was characterized using scanning electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis and inductively coupled plasma technique. The catalytic application of Pr.S‐ZrO@boehmite was studied in C–O and C–S coupling reactions for synthesis of valuable compounds such as ether and sulfide derivatives. All products were obtained in good to excellent yields and the catalyst could be recovered and reused several times without significant loss of catalytic efficiency. Furthermore, zirconium oxide is rarely used as catalyst for cross‐coupling reactions.     

Monitoring bisphosphonate surface functionalization and acid stability of hierarchically porous titanium zirconium oxides

To take advantage of the full potential of functionalized transition metal oxides, a well-understood nonsilane based grafting technique is required. The functionalization of mixed titanium zirconium oxides was studied in detail using a bisphosphonic acid, featuring two phosphonic acid groups with high surface affinity. The bisphosphonic acid employed was coupled to a UV active benzamide moiety in order to track the progress of the surface functionalization in situ. Using different material compositions, altering the pH environment, and looking at various annealing conditions, key features of the functionalization process were identified that consequently will allow for intelligent material design. Loading with bisphosphonic acid was highest on supports calcined at 650 °C compared to lower calcination temperatures: A maximum capacity of 0.13 mmol g(-1) was obtained and the adsorption process could be modeled with a pseudo-second-order rate relationship. Heating at 650 °C resulted in a phase transition of the mixed binary oxide to a ternary oxide, titanium zirconium oxide in the srilankite phase. This phase transition was crucial in order to achieve high loading of the bisphosphonic acid and enhanced chemical stability in highly acidic solutions. Due to the inert nature of phosphorus-oxygen-metal bonds, materials functionalized by bisphosphonic acids showed increased chemical stability compared to their nonfunctionalized counterparts in harshly acidic solutions. Leaching studies showed that the acid stability of the functionalized material was improved with a partially crystalline srilankite phase. The materials were characterized using nitrogen sorption, X-ray powder diffraction, and UV-vis spectroscopy; X-ray photoelectron spectroscopy was used to study surface coverage with the bisphosphonic acid molecules.