Glucose biosensor based on glucose oxidase immobilized in sol–gel chitosan/silica hybrid composite film on Prussian blue modified glass carbon electrode

An improved amperometric glucose biosensor based on glucose oxidase immobilized in sol–gel chitosan/silica hybrid composite film, which was prepared from chitosan (CS) and methyltrimethoxysilane (MTOS), on the surface of Prussian blue (PB)-modified glass carbon electrode was developed. The film was characterized by FT-IR. Effects of some experimental variables such as ratio of CS to silica, buffer pH, temperature, and applied potential on the current response of the biosensor were investigated. The biosensor fabricated under optimal conditions had a linear response to glucose over the range 5.0×10^–5 to 2.6×10^–2 M with a correlation coefficient of 0.9948 and a detection limit of 8.0×10^–6 M based on S/N =3. The biosensor had a fast response time of less than 10 s, a high sensitivity of 420 nA mM^–1, a long-term stability of over 60 days, and a good selectivity. The apparent Michaelis–Menten constant K_m was found to be 3.2×10^–3 M. The activation energy for enzymatic reaction was calculated to be 21.9 kJ mol^–1. This method has been used to determine the glucose concentration in real human blood samples.     

Adsorptive accumulation voltammetry of copper(II) using complex formation reaction with salicylideneamino-2-thiophenol

Summary The cathodic stripping voltammetry of copper(II) was investigated with a method, based on the adsorptive accumulation of the Cu(II)-salicylideneamino-2-thiophenol (SATP) complex on a hanging mercury drop electrode. The copper(II)-SATP complex could be accumulated on the electrode at –0.20 V in 0.01 mol/l nitric acid. The reduction peak of the copper complex was observed by scanning the potential in a negative direction in the differential pulse mode. The calibration curve for copper was linear over the range 5×10^–9–1×10^–7 mol/l. This method was applied to determine copper(II) in GSJ (Geological Survey of Japan) standard rock reference materials.     

Determination of nanomolar levels of guanine by differential-pulse adsorptive cathodic stripping voltammetry of its copper(II) complex

Guanine is determined at the 5.0×10^–10 –2.0×10^–7 mol/l level by differential-pulse adsorptive stripping voltammetry at a hanging mercury drop electrode using the reduction peak of its copper (II) complex at –0.21 V vs. Ag-AgCl electrode. The optimum analytical conditions were found to be Britton-Robinson buffer solution (pH 4.8), an accumulation potential of 0.0 V and an accumulation time of 3 min. Under these conditions, the detection limit is 5.0×10^–10 mol/l and the relative standard deviation 2.6% for 1.0×10^–7 mol/l guanine. The method is compared with the previous voltammetric methods. The presence of some purine derivatives does not interfere.     

Anodic stripping voltammetric determination of mercury using multi-walled carbon nanotubes film coated glassy carbon electrode

An electrochemical method for the determination of trace levels of mercury based on a multi-walled carbon nanotubes (MWNT) film coated glassy carbon electrode (GCE) is described. In 0.1 mol L^–1 HCl solution containing 0.02 mol L^–1 KI, Hg²⁺ was firstly preconcentrated at the MWNT film and then reduced at –0.60 V. During the anodic potential sweep, reduced mercury was oxidized, and then a sensitive and well-defined stripping peak at about –0.20 V appeared. Under identical conditions, a MWNT film coated GCE greatly enhances the stripping peak current of mercury in contrast to a bare GCE. Low concentrations of I^– remarkably improve the determining sensitivity, since this increases the accumulation efficiency of Hg²⁺ at the MWNT film coated GCE. The stripping peak current is proportional to the concentration of Hg²⁺ over the range 8×10^–10–5×10^–7 mol L^–1. The lowest detectable concentration of Hg²⁺ is 2×10^–10 mol L^–1 at 5 min accumulation. The relative standard deviation (RSD) at 1×10^–8 mol L^–1 Hg²⁺ was about 6% (n=10). By using this proposed method, Hg²⁺ in some water samples was determined, and the results were compared with those obtained by atomic absorption spectrometry (AAS). The two results are similar, suggesting that the MWNT-film coated GCE has great potential in practical analysis.     

Determination of dinoseb by adsorptive stripping voltammetry using a mercury film electrode

An adsorptive stripping voltammetric method for the determination of the pesticide dinoseb (2-sec.-butyl-4,6-dinitrophenol) at the mercury film electrode is described. The deposition of the mercury film on a glassy carbon disk electrode was optimized. The temperature, at which the mercury film was deposited, was demonstrated to have a strong influence on the stripping peaks, the first one being much more intense than the second. A systematic study of the variables affecting the stripping response was carried out by differential pulse voltammetry. The results obtained have been compared with those at the HMDE; a significant improvement in the sensitivity of the method developed with the MFE was observed. Using a 300 s accumulation time, the limits of determination and detection were 3.6 × 10^–10 and 1.1 × 10^–10 mol L^–1, respectively. The effect of the presence of several herbicides on the dinoseb response was also tested. The method has been applied to the determination of the pesticide in spiked apple juice at two concentration levels: 12.0 and 1.2 g L^–1 of juice.     

Voltammetric trace determination of ubiquinones at mercury electrodes

Summary Voltammetric methods were developed for the determination of ubiquinones on the basis of their adsorption and redox behaviour at mercury electrodes. Linear calibration plots were obtained in the concentration range between 10^–4 mol/l and 2.3·10^–5 mol/l from differential pulse voltammetric measurements under experimental conditions avoiding significant adsorption of the analyte. A remarkable decrease of the detection limit down to 10^–7 mol/l was achieved with the help of adsorptive accumulation of ubiquinone molecules at the mercury electrode followed by differential pulse detection. The resulting non-linear calibration plot was explained with a model, which takes into account both adsorption and diffusion of the analyte.     

Electrocatalytic oxidation of thiosulfate on a modified nickel hexacyanoferrate film electrode

Summary A modified nickel hexacyanoferrate film glassy carbon electrode is prepared by the electrochemical deposition technique. The film is very stable upon voltammetric scanning in the potential range of 1.0 to –0.5 V (vs. SCE) and an oxidation peak occurs at 0.35 V (vs. SCE) (1 mol/l NaNO₃). The effects of electrolyte, solvent, coexisting ions and other variables on the voltammetric behaviour of the modified film have been studied. The thickness of the resulting film can be controlled by changing the number of voltammetric cycles and the concentrations of nickel(II) and hexacyanoferrate(III) ions. The film shows catalytic activity towards electrooxidation of thiosulfate with a peak potential +0.5 V (K^–-containing media). This oxidation potential of thiosulfate on the modified electrode is shifted negatively by about 550 mV as compared to the naked glassy carbon electrode. For practical application, the modified electrode can be used for the determination of thiosulfate in concentrations from 5.0×10^–5 to 1.0×10^–1 mol/l. This method has been successfully applied to the determination of thiosulfate in photographic waste effluents.     

Enzyme sensor for L-lactate using differential pulse amperometric detection

An enzyme sensor using differential pulse (DP) amperometric detection has been developed based on the measurement of the reduction current of the oxidized form of -nicotinamide adenine dinucleotide (NAD⁺) consumed by an enzyme reaction. This biosensor has the definite advantage to prevent interference caused by electrooxidative species such as ascorbate and uric acid and exhibits higher sensitivity and selectivity in comparison to the classical DC amperometric detector. The linear detection range of this biosensor was 5.0×10^–5 — 5.0×10^–4 mol/l and the relative standard deviation (R.S.D.) at 2.5×10^–4 mol/l was 5.0%.     

A novel amperometric sensor and chromatographic detector for determination of parathion

A novel amperometric sensor and chromatographic detector for determination of parathion has been fabricated from a multi-wall carbon nano-tube (MWCNT)/Nafion film-modified glassy-carbon electrode (GCE). The electrochemical response to parathion at the MWCNT/Nafion film electrode was investigated by cyclic voltammetry and linear sweep voltammetry. The redox current of parathion at the MWCNT/Nafion film electrode was significantly higher than that at the bare GCE, the MWCNT-modified GCE, and the Nafion-modified GCE. The results indicated that the MWCNT/Nafion film had an efficient electrocatalytic effect on the electrochemical response to parathion. The peak current was proportional to the concentration of parathion in the range 5.0×10^–9–2.0×10^–5 mol L^–1. The detection limit was 1.0×10^–9 mol L^–1 (after 120 s accumulation). In high-performance liquid chromatography with electrochemical detection (HPLC–ED) a stable and sensitive current response was obtained for parathion at the MWCNT/Nafion film electrode. The linear range for parathion was over four orders of magnitude and the detection limit was 6.0×10^–9 mol L^–1. Application of the method for determination of parathion in rice was satisfactory.     

Studies on the voltammetric behaviour of salicyl fluorone and gallium-salicyl fluorone complex

In the NH₄Cl supporting electrolyte, within the pH range from 1 to 5, an irreversible adsorptive reducing wave of salicyl fluorone(SAF) was obtained. The electrode process was verified as follow: On the surface of mercury electrode, the adsorption of SAF obeys Frumkin isotherm.In 0.2 mol/l potassium hydrogen phthalate/HCl buffer solution, at pH 3.0, the sensitive adsorptive complex wave of Ga-SAF was obtained by linear sweep voltammetry. The composition of the electroactive complex was determined as Ga:SAF = 11. The peak height of the complex is proportional to the concentration of Ga(III) in the range of 1.5 × 10^–9 to 6.0 × 10^–7 mol/l, the detection limit is 1.0× 10^–9 mol/l. The proposed method has been applied to the determination of gallium content in aluminium alloys.     

Potentiometric determination of mercury(II) and thiourea in strong acid solution using an ion-selective electrode with AgI-based membrane hydrophobised by PTFE

Summary The potentiometric determination of mercury(II) and thiourea (TU) in strong acid solution (pH 0–1) by using an all-solid-state ion-selective electrode with (Ag₂S 25%, AgI 25% and PTFE 50% m/m)-membrane is described. The linear response, 43 mV(pHg)^–1 and 80 mV(pTU)^–1, has been obtained in the concentration range from 10^–2 to under 10^–5 mol/l. By direct potentiometry at pH 0 mercury(II) can be determined in the presence of up to 10^–3 mol/l of iron(III). The change in potential in the tested concentration range of thiourea indicates the formation of Ag(TU) _1.4 ⁺ at the exposed surface of the membrane. This stoichiometry is in good agreement with that calculated from the average Ag/TU ratio in the potentiometric titration. The investigated electrode can be used as a good sensor for mercury(II) and thiourea in strong acid media and a wide variety of practical analytical systems.     

Determination of Mo(VI) with 2-benzylideneiminobenzohydroxamic acid (2-BIBH) in urine by cathodic stripping voltammetry

Summary Controlled adsorptive accumulation of Mo(VI)-2-BIBH at the hanging mercury drop electrode (HMDE) provides the basis for the direct stripping measurement of Mo(VI) in nanomolar concentration. The cathodic stripping response is evaluated with respect to experimental parameters such as preconcentration time, preconcentration potential and others. A differential pulse cathodic stripping voltammetric method for the determination of Mo(VI) with 2-BIBH in urine is proposed. The detection limit is 10^–9 mol/l Mo(VI), standard deviation for 5×10^–8 mol/l is ±1.58×10^–9 mol/l.

---

Bestimmung von MolybdÄn(VI) mit 2-BenzylideniminobenzohydroxamsÄure (2-BIBH) in Harn durch kathodische Stripping-Voltammetrie

     

Determination of tyrosine traces by adsorption voltammetry of its copper (II) complex

The electrochemical behavior of the copper-tyrosine complex has been studied by linear-sweep adsorption voltammetry. In 0.02 mol/L Na₂HPO₄ buffer solution (pH=9.6), the complex can be adsorped on a hanging mercury drop electrode and reduced at a peak potential of about –0.42 V (vs. SCE). The secondary derivative peak height is linear proportional to the concentration of tyrosine in the range 1.0×10^–7–5.0×10^–5 mol/L. The detection limit is 5×10^–8 mol/L.Project supported by the Provincial Science Foundation of Shandong Province     

Adsorptive stripping voltammetric determination of 1-(4′-bromophenyl)-3,3-dimethyltriazene

The optimum conditions were established for the determination of the genotoxic substance 1-(4-bromophenyl)-3,3-dimethyltriazene by differential-pulse voltammetry at a hanging mercury drop electrode in the concentration range 1 × 10^–4 to 1 × 10^–7 mol dm^–3. The sensitivity of the determination can be improved through adsorptive accumulation of the investigated substance on the surface of the hanging mercury drop electrode: differential pulse adsorptive stripping voltammetry can be used in the concentration range 1 × 10^–7 to 2 × 10^–10 mol dm^–3. The relative standard deviation (for ten determinations at 2 × 10^–10 mol dm^–3) was 7.5%.     

Selective method for the determination of gold by anodic stripping voltammetry

A highly selective method for the deter- mination of gold by anodic stripping voltammetry is described. For preconcentration a glassy carbon electrode, activated by deposition of small amounts of gold before the measurement, is proposed. The Au³⁺ reduction process at such an electrode is effective starting with the potential +0.4 V vs. Ag/AgCl electrode. A linear dependence of the current of the gold stripping peak on the gold concentration was obtained in the range from 5×10^–8 to 1×10^–6 mol/l. The relative standard deviation for 2×10^-7 mol/l HAuCl₄ was 4.2% (n=5). The detection limit was 4×10^-9 mol/l. The accuracy of the method was verified by the determination of gold in reference materials.     

Composite film of carbon nanotubes and chitosan for preparation of amperometric hydrogen peroxide biosensor

A new amperometric biosensor for hydrogen peroxide was developed based on cross-linking horseradish peroxidase (HRP) by glutaraldehyde with multiwall carbon nanotubes/chitosan (MWNTs/chitosan) composite film coated on a glassy carbon electrode. MWNTs were firstly dissolved in a chitosan solution. Then the morphology of MWNTs/chitosan composite film was characterized by field-emission scanning electron microscopy. The results showed that MWNTs were well soluble in chitosan and robust films could be formed on the surface. HRP was cross-linked by glutaraldehyde with MWNTs/chitosan film to prepare a hydrogen peroxide biosensor. The enzyme electrode exhibited excellent electrocatalytic activity and rapid response for H₂O₂ in the absence of a mediator. The linear range of detection towards H₂O₂ (applied potential: −0.2 V) was from 1.67 × 10⁻⁵ to 7.40 × 10⁻⁴ M with correction coefficient of 0.998. The biosensor had good repeatability and stability for the determination of H₂O₂. There were no interferences from ascorbic acid, glucose, citrate acid and lactic acid.     

Adsorptive stripping voltammetric measurements of trace amounts of platinum(II) and ruthenium(III) in the presence of 1-(2-pyridylazo)-2-naphthol

An extremely sensitive stripping voltammetric procedure for low level measurements of platinum (II, IV) or ruthenium (III, IV) is reported. The method is based on the interfacial accumulation of the platinum (II) or ruthenium (III)-1-(2-pyridylazo)-2-naphthol complex on the surface of a hanging mercury drop electrode, followed by the reduction of the adsorbed complex during the cathodic scan. The peak potential was found to be –0.8 V vs. Ag/AgCl electrode and the reduction current of the adsorbed complex ions of platinum (II) or ruthenium (III) was measured by differential pulse cathodic stripping voltammetry. The optimum experimental conditions were: 1.5×10^–7 mol/l of 1-(2-pyridylazo)-2-naphthol solution of pH 9.3, preconcentration potential of –0.2 V, accumulation time of 3 min and pulse amplitude of 50 mV with 4 mV s^–1 scan rate in the presence of ethanol-water (30% v/v) — sodium sulphate (0.5 mol/l). Linear response up to 6.4 × 10^–8 and 5.1 × 10^–8 mol/l and a relative standard deviation (at 1.2×10^–8 mol/l) of 2.4 and 1.6% (n=5) for platinum (II) and ruthenium (III) respectively were obtained. The detection limits of platinum and ruthenium were 3.2×10^–10 and 4.1×10^–10 mol/l, respectively. The electronic spectra of the Pt(II) — PAN and Ru(III) — PAN complexes were measured at pH 9.3 and the stoichiometric ratios of the complexes formed were obtained by the molar ratio method. The effects of some interfering ions on the proposed procedure were critically investigated. The method was found suitable for the sub-microdetermination of ruthenium (IV) and platinum (IV) after their reduction to ruthenium (III) and platinum (II) with sulphur dioxide in acid media. The applicability of the method for the analysis of binary mixtures of ruthenium (III) and (IV) or platinum (II) and (IV) has also been carried out successfully. The method is simple, rapid, precise, and promising for the determination of the tested metal ions at micro-molar concentration level.     

Influence of hydrodynamic conditions of the solution on the sensitivity of stripping analysis of trace metals

Possibilities to increase the sensitivity of stripping analysis by optimising the hydrodynamic conditions of the solution during the deposition and rest period are evaluated. Rotation rates as high as 13 000 rpm can be applied during the deposition step at a mercury film rotating disc electrode for Zn, Cd, Pb, In and Tl determinations when 10–20 mg/l of Hg²⁺ for the renewal of the mercury film is added. Because of the extreme sensitivity on the properties of the mercury film in the case of Ga only 4000–5000 rpm are recommended. The highest stirring efficiencies using a magnetic stirrer are equivalent to 2500–3000 rpm when a rotating disc electrode is used. The effect of the duration of the rest period is not significant for square wave stripping voltammetry, however, analytical signals can be increased 10 and more times when potentiometric stripping analysis is applied.     

Use of a crown ether-heteropoly acid precipitate as a potassium ion-selective membrane electrode

Summary A Potassium ion-selective electrode based on dibenzo-18-crown-6-tungstophosphoric acid precipitate membrane is prepared and conditions for the best functioning have been investigated. The working concentration and pH-range of the electrode is 2.0×10^–2 to 1.3×10^–6 mol/l and 2.9–6.5, respectively. The selectivity coefficient values for a large number of cations are quite low except for caesium and ammonium ions. The electrode can tolerate non-aqueous content upto 20%.

---

Kaliumion-sensitive Membranelektrode auf Basis von Kronenether-Heteropolysäure

     

Determination of Enalapril by Stripping Voltammetry at a Mercury Film Electrode

A procedure was developed for determining 4.0 × 10^–6 to 2.6 × 10^–3 M enalapril in model solutions and blood serum by anodic stripping voltammetry at a mercury film electrode.__________Translated from Zhurnal Analiticheskoi Khimii, Vol. 60, No. 5, 2005, pp. 495–498.Original Russian Text Copyright © 2005 by Gusakova, Ivanovskaya.