MgFe2O4-Fe2O3纳米粉体的软化学合成及电磁学特性

Nano-MgFe₂O₄-Fe₂O₃ magnetic powders were synthesized by citrate gel under microwave irradiation. The structure，particle size distribution，electromagnetic characteristics of nano-MgFe₂O₄-Fe₂O₃ were characterized by using TG-DTA, X-ray, electronic microscope, nano-size measurement and electromagnetism measurement apparatus。The results show that the product is a mixture of MgFe₂O₄ and Fe₂O₃ with average size of 44 nm, tanδ for the product is 0.265 and 0.610 at frequency of 1.0 GHz and 1.8 GHz respectively.     

Cu-Ni/La2O3热解C2H2制备碳纳米管的研究

Nano-sized and well-dispersed Cu-Ni/La₂O₃ can be obtained by reduction of LaCu_0.2Ni_0.8O₃ with the structure of perovskite. Using Cu-Ni/La₂O₃ as catalyst and C₂H₂ as carbon source, carbon nanotubes with a high yield and narrow diameter distribution can be obtained in the reaction temperature range of 650～700℃. Outer diameter of carbon nanotubes rangs from 9nm to 14nm. TG, Raman and XPS analysis indicate that carbon nanotubes prepared by Cu-Ni/La₂O₃ are relatively higher in graphitic degree.     

ZrxTixAl1-2xO2的制备及其在三效催化剂上的应用

Zr_0.5Ti_0.5O₂(ZT) and Zr_0.25Ti_0.25Al_0.5O₂(ZTA) mixed oxides were prepared by co-precipitation method and characterized by low temperature adsorption-desorption， XRD and NH₃-TPD. The activity of Pt/Zr_0.5Ti_0.5O₂ and Pt/ Zr_0.5Ti_0.5Al_0.5O₂ catalysts was evaluated using the simulated gases. The results show that ZTA samples exhibit higher specific surface area， larger pore volume and proper surface acidic amount and acidity in comparison with ZT. The results of the catalytic test indicate that Pt/ZT and Pt/ZTA catalysts exhibit excellent low-temperature catalytic activity and lower light-off temperatures of hydrocarbon， carbon monoxide and nitrogen oxides， especially better conversion for nitrogen oxides (NO_x). The addition of Al₂O₃ into ZT enhanced the anti-aging property of Pt/ ZTA catalysts due to the excellent textural， structural， surface acidity and thermal stability.     

Ceramic Filter Balls Loaded with α-Fe2O3 and Their Application to NH3-N Wastewater Treatment

Hydrolysis reaction of Fe(NO₃)₃ at a high temperature in the presence of urea as the homogeneous precipitant was studied. With the prepared ceramic filter balls loaded with α-Fe₂O₃ after high temperature calcination, the loading of α-Fe₂O₃ on the porous ceramic filter balls from Fe(NO₃)₃ solutions of different concentrations and mechanical stability of the loaded α-Fe₂O₃ were studied. The product was characterized using XRD and SEM. Adsorption experiments were conducted to evaluate the performance of the product in adsorbing NH₃-N. It turned out that the specific surface area of the ceramic filter balls loaded with α-Fe₂O₃ had increased to 36.5387 m²/g from original 4.6127 m²/g. When the concentration of Fe(NO₃)₃ was 0.40 mol/L, the loading of α-Fe₂O₃ on the ceramic filter balls accounted for 8.4% of the total mass of the adsorbent and α-Fe₂O₃ was adsorbed on the filter balls very well. The adsorption isotherm of NH₃-N on the ceramic filter ball adsorbent loaded with α-Fe₂O₃ was of Langmuir type. The saturated adsorption capacity was 3.33 mg/L, and the adsorption constant K was 0.1873. NH₃-N was adsorbed by α-Fe₂O₃ more easily, which was a kind of specific adsorption.     

磁性Fe3O4 /壳聚糖的化学修饰及包覆机理研究

Nano-sized Fe₃O₄ powder was prepared through an Oxygenation-Hydrothermal method. The chitosan magnetic complex was prepared by coating chitosan on the surface of Fe₃O₄ powders through Microlatex-Crosslinking Method. The product was characterized by IR， XRD， TEM， Vibrating Sample Magnetometer (VSM)， TG methods. Results show that the as-prepared powder is 25 nm in size and shows supermagnetism. The content of magnetite in microspheres is 37.8%. The mechanism for the coating reaction of chitosan to Fe₃O₄ nanoparticles is also suggested.     

球形α-Fe2O3纳米粉体的超声水解法合成与表征

Hematite (α-Fe₂O₃) nanopowder was synthesized from 0.1 mol·L^-1 FeCl₃ solution by sonochemical hydrolysis method, and characterized by X-ray diffraction (XRD), transmission electron micrograph (TEM), Fourier transform infrared (FTIR), Fourier transform Raman (FT-Raman) and X-ray photoelectron spectroscopy (XPS). The results showed that the spherical, well-dispersed α-Fe₂O₃ nanopowder was obtained with the average size of 20 nm. The possible mechanism for the formation of α-Fe₂O₃ nanoparticals was also discussed.     

Fe3O4磁液的悬浮率测定及稳定性研究

The paper first reported the preparation of ultrafine Fe₃O₄ powder about 8～10nm by improved chemical pre-cipitation method， then turned it into magnetic fluid. The phase analysis， morphology， ultrafine powder size and magnetic property were measured by XRD， TEM and vibrating sample magnetometer(VSM)，respectively. In ad-dition， a new method ， by analyzed the suspending percentage of Fe₃O₄ powder， was introduced to study the effects of concentration， pH value， centrifugal rate and time on the stability of the magnetic fluid.     

电镀烧结法制备Ti/SnO2-Sb2O4电极的研究

The Ti/SnO₂-Sb₂O₄ electrode has been prepared by the electroplate-sinter method. The effect of SbCl₃ adding amount and sintering temperature on its electrode lifetime and oxygen evolution potential were investigated by means of EDX, SEM and XRD analysis. The results indicated that the electrode appeared the best performance when the SbCl₃ adding amounts was 0.2g and the sintering temperature was 550℃. In optimized conditions Ti substrate was entirely covered by SnO₂-Sb₂O₄ and the combinations among them were tight. Due to the use of electroplate method, the electrical conductivity, the oxygen evolution potential and the electrode lifetime were increased, so the elec-tro-catalytic activity and the electrochemical stability of the prepared electrode were found to be superior.     

LiV3O8的合成及其电化学性能研究

The layered trivanadate, LiV₃O₈, was prepared by sol-gel method with LiOH, V₂O₅ and H₂O₂ as initial reagents. The materials at different heat treatment conditions were characterized by XRD and TG-DTA. Their electrochemical behaviors were studied by galvanostatic charge-discharge and cyclic voltammetry. The results show that LiV₃O₈ prepared by sintering at 300 ℃ for 16 h has higher capacity, and its initial discharge capacity is 333.1 mAh·g^-1, and maintains a discharge capacity of 302.8 mAh·g^-1 after 10 cycles at 0.2 C and the voltage range of 1.8～4.0 V.     

新型阴极材料Ba0.5Sr0.5Co0.8Fe0.2O3-σ制备与性能研究

Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3-σ(BSCF), a new cathode material for solid oxide fuel cell (SOFC), was synthesized by polyacrylicacid (PAA) method. The lattice structures of samples calcined at different temperatures were characte-rized by XRD. Shrinkage, porosity and pore size of the porous BSCF as a function of sintering temperature were investigated. It was found that the cubic perovskite structure could be formed after calcination at 800 ℃ for 2 h, but not well crystallized as seen from some unknown phases, and the pure cubic perovskite structure was formed after calcination at 1 150 ℃ for 2 h. The particle size of BSCF was less than 1～2 μm. The shrinkage of the porous BSCF increased with sintering temperature, but the opposite was true for the porosity. After sintering at 1 100 ℃ for 4 h, the porous BSCF was still in an appropriate structure, with porosity of 29% and electrical conductivity above 400 S·cm^-1.     

Ag3PO4/Ag2S/g-C3N4复合光催化剂的制备与性能

通过沉积法和离子交换法成功地制备了Ag_3PO_4/Ag_2S/g-C_3N_4复合型光催化剂。利用X射线多晶粉末衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、N_2吸附-脱附等温线、紫外-可见漫反射光谱、荧光光谱等手段对样品进行了表征。通过降解罗丹明B考察其可见光催化活性及稳定性,研究了硫化钠与磷酸银物质的量的比值(n_(Na_2S)/n_(Ag_3PO_4))、g-C_3N_4添加量对所制备复合光催化材料性能的影响,同时对光催化机理进行了探讨。结果表明,随着n_(Na2S)/n_(Ag3PO4)的增加,所得复合催化材料活性先增加后降低;当n_(Na2S)/n_(Ag_3PO_4)为1.5%、g-C_3N_4与Ag_3PO_4的质量比为3∶7时制备的催化剂ASC1.5的光催化活性最好,在可见光照射下,40 min内可将罗丹明B完全降解,且5次循环使用后仍保持较高的催化活性。和Ag_3PO_4相比,Ag_3PO_4/Ag_2S/g-C_3N_4复合型光催化材料的活性与稳定性都得到明显提高,这主要归因于复合催化剂比表面积和孔结构的增加,载流子分离效率的提高。光催化机理研究表明,空穴(h~+)、超氧阴离子自由基(·O~(2-))和羟基自由基(·OH)都是光催化过程中的主要活性物种。三者作用大小依次为:h~+·O~(2-)·OH。     

荧光XAFS表征Pt/BaAl2O4-Al2O3催化剂中的微量铂物种

随着稀薄燃烧(lean-burn)发动机的推广使用和环保法规的日趋严格,消除稀燃尾气中的氮氧化物(N O x)已刻不容缓。N O x储存还原技术被认为是最具应用前景的方法之一[1,2]。目前,对Pt/BaA l2O4-A l2O3体系中N O x储存与还原机制的研究较多[1￣4],但对该体系中微量铂物种微观结构及其与性能的关系研究较少,这主要是由于Pt含量(0.1w t%￣0.5wt%)太低,分散度较高,使表征方法受到很大限制。本文采用共沉淀-浸渍法制得具有较高比表面积和热稳定性的N O x储存还原催化剂Pt/BaA l2O4-A l2O3,应用荧光X-射线吸收精细结构方法(Fluores-cence-…     

Following the crystallisation of Bi2Mo2O9 catalyst by combined XRD/QuEXAFS

The formation ofβ-phase Bi₂Mo₂O₉ catalyst from a precursor precipitate has been studied using thein situ combined XRD/QuEXAFS technique and DSC during calcination. Accordingly the precursor was observed to undergo a number of changes in both the molybdenum (VI) coordination and long-range ordering during this heating. Initially the two other forms of bismuth molybdate (α-andγ-phases) were observed to form from the poorly crystalline precursor at about 230°C, however, theβ-phase eventually crystallised after prolonged heating at 560°C. Dedicated to Professor C N R Rao on his 70th birthday     

Sol-gel synthesis of K3InF6 and structural characterization of K2InC10O10H6F9, K3InC12O14H4F18 and K3InC12O12F18

K₃InF₆ is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K₂InC₁₀O₁₀H₆F₉, K₃InC₁₂O₁₄H₄F₁₈ and K₃InC₁₂O₁₂F₁₈. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. The two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K₃InF₆ by decomposition at high temperature. The crystal structure of K₃InC₁₂O₁₄H₄F₁₈ is characterized by complex anions [In(CF₃COO)₄(OH_x)₂]^(5−2x)− and isolated [CF₃COOH_2−x]^(x−1)− molecules with x=2 or 1, surrounded by K⁺ cations. The crystal structure of K₃InC₁₂O₁₂F₁₈ is only constituted by complex anions [In(CF₃COO)₆]³⁻ and K⁺ cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K₂InC₁₀O₁₀H₆F₉ and K₃InC₁₂O₁₂F₁₈ were also performed at room temperature on pulverized crystals.     

Effect of 3% Re2O7/60%Al2O3 - 40%SiO2 Catalyst Alkylation Time and Temperature Using Et4Pb on Methyl Erucate Conversion

A study of the alkylation of 3% Re₂O₇/60%Al₂O₃-40%SiO₂ catalyst using tetraethyllead (Et₄Pb)(TEL) shows that the reaction time and temperature affect the catalyst activity and selectivity in the methyl erucate metathesis reaction. This revised version was published online in June 2006 with corrections to the Cover Date.     

磁性Y-MOF@SiO2@Fe3O4催化剂的制备及其在Aza-Micheal加成反应中的性能

在磁性SiO₂@Fe₃O₄纳米微球表面原位合成包覆不同含量的Y-MOF,从而制备出新型磁性Y-MOF@SiO₂@Fe₃O₄催化剂。采用XRD、TEM、FT-IR、VSM和N₂吸附-脱附测试等手段对催化剂的结构进行表征,并且评价了催化剂对苯胺和丙烯酸甲酯的Aza-Micheal加成反应性能。结果表明Y-MOF能均匀包覆在磁性SiO₂@Fe₃O₄纳米微球表面,形成具有核壳结构的磁性Y-MOF@SiO₂@Fe₃O₄催化剂,催化剂具有良好的超顺磁性。Y-MOF含量为43.3%（w/w）的Y-MOF@SiO₂@Fe₃O₄催化剂,在苯胺和丙烯酸甲酯的Aza-Micheal加成反应表现出最好的催化性能,丙烯酸甲酯的转化率为88.3%时,N-（β-甲氧碳酰乙基）苯胺的选择性可达99.8%。反应后的催化剂可以通过外磁场容易回收,并且重复使用5次其转化率和选择性没有明显下降。     

Pt/ZrO2-Al2O3催化剂催化氧化C3H6和CO性能

采用共沉淀法合成了ZrO₂与Al₂O₃的不同质量比的ZrO₂-Al₂O₃复合氧化物,并以此为载体通过等体积浸渍法制备了1.5% Pt/ZrO₂-Al₂O₃（w/w）催化剂。以C₃H₆和CO为反应物的催化性能评价显示,在系列催化剂中以Pt/Zr（0.4）-Al₂O₃催化剂催化氧化活性最为优异,其C₃H₆和CO的起燃温度（T₅₀）小于125℃,完全转化温度（T₉₀）小于150℃。采用XRD、低温N₂吸附、H2-TPR、CO脉冲吸附等分析表征技术探索了催化剂物相结构、比表面积、颗粒尺寸等对催化活性的影响规律。结果发现,ZrO₂-Al₂O₃复合氧化物具有Al₂O₃材料的介孔织构和大比表面积特性,且产生了Al_xZr_1-xO_y固溶体新物相。适当的ZrO₂与Al₂O₃的质量比,是改善Pt与ZrO₂-Al₂O₃的相互作用强度,促进贵金属Pt的分散,提升Pt/ZrO₂-Al₂O₃催化剂的低温氧化活性的关键。     

Pt/ZrO2-Al2O3催化剂催化氧化C3H6和CO性能

采用共沉淀法合成了ZrO₂与Al₂O₃的不同质量比的ZrO₂-Al₂O₃复合氧化物,并以此为载体通过等体积浸渍法制备了1.5% Pt/ZrO₂-Al₂O₃（w/w）催化剂。以C₃H₆和CO为反应物的催化性能评价显示,在系列催化剂中以Pt/Zr（0.4）-Al催化剂催化氧化活性最为优异,其C₃H₆和CO的起燃温度（T₅₀）小于125℃,完全转化温度（T₉₀）小于150℃。采用XRD、低温N₂吸附、H₂-TPR、CO脉冲吸附等分析表征技术探索了催化剂物相结构、比表面积、颗粒尺寸等对催化活性的影响规律。结果发现,ZrO₂-Al₂O₃复合氧化物具有Al₂O₃材料的介孔织构和大比表面积特性,且产生了Al_xZr_1-xO_y固溶体新物相。适当的ZrO₂与Al₂O₃的质量比,是改善Pt与ZrO₂-Al₂O₃的相互作用强度,促进贵金属Pt的分散,提升Pt/ZrO₂-Al₂O₃催化剂的低温氧化活性的关键。     

Microwave-promoted efficient conversion of acetophenones to 1,3,5-triarylbenzenes catalyzed by H3PW12O40 and nano-silica supported H3PW12O40 as reusable catalysts

H₃PW₁₂O₄₀ and nano-silica supported H₃PW₁₂O₄₀ were found to be efficient heterogeneous catalysts for the preparation of 1,3,5-triarylbenzenes via triple self condensation of acetophenones under microwave irradiation and solvent-free conditions. High yields, short reaction times, easy work-up, easy availability and handling, eco-friendly and reusability of the catalysts are the main aspects of the present method. The catalytic mechanism of 1,3,5-triarylbenzenes synthesis is also proposed.     

Cp2TiCl2 catalyzed one-pot synthesis of n-Bu3GeH from GeCl4

The reaction of GeCl₄ with n-BuMgCl in presence of a catalytic amount of Cp₂TiCl₂ gives n-Bu₃GeH and n-Bu₄Ge in ca. 70 and 25% yield, respectively. This method provides an industrially feasible one-pot synthesis for Bu₃GeH and Bu₄Ge. The reaction temperature and stoichiometry seem to be important in the distribution of the products. Apart from elemental analysis these compounds have been characterized by comparing their boiling points, NMR spectral data and GC assay with that of the authentic samples.