A new flow-injection determination of glucose based on the redox reaction of hydroquinone with iron(III) in the presence of 1,10-phenanthroline

A new spectrophotometric flow-injection (FI) method is proposed for the determination of glucose based on the redox reaction of hydroquinone with iron(III). When a glucose solution containing quinone is passed through the immobilized glucose oxidase column introduced in FI system, quinone is reduced to hydroquinone by glucose. In the presence of 1,10-phenanthroline (phen), iron(III) is then quantitatively reduced by hydroquinone to iron(II) followed by the formation of iron(II)-phen complex (λ_max=510 nm). An FI peak observed at 510 nm corresponds to the concentration of glucose. The wide dynamic range for glucose was obtained in the range of 1×10⁻⁶–1×10⁻³ mol l⁻¹ at a sampling rate of 24 h⁻¹ and the detection limit (S/N=3) was 5×10⁻⁷ mol l⁻¹. Relative standard deviations were 0.78, 0.44 and 0.23% (n=5) for 5×10⁻⁶, 5×10⁻⁵ and 5×10⁻⁴ mol l⁻¹ of glucose, respectively. The proposed method was successfully applied to the determination of glucose in control blood sera, human blood plasma and wine.     

Determination of Ag(I) with chemically modified carbon paste electrode based on 2,3-dicyano 1,4-naphthoquinone

The utility of carbon paste modified with 2,3-dicyano 1,4-naphthoquinone (CYNQ) for the voltammetric determination of Ag(I) is demonstrated. The method is based on the formation of Ag(I) complex with CYNQ by accumulation from the aqueous solution to the electrode surface without an applied potential. Using the medium exchange technique, the electrode was transferred to another media followed by linear-scan voltammetric measurements. The reduction peak of the Ag(I)-CYNQ complex was observed at +0.22 V (vs. SCE). The silver response is studied with respect to paste composition, pH of the measurement solution, reproducibility, interference and other variables. A detection limit of 5 × 10⁻⁸M was obtained and the calibration curve was linear over the range 1 × 10⁻⁶−8 × 10⁻⁵M.     

Separation of trans-1,2-cyclohexanediaminetetra-acetic acid chelates of bismuth(III), iron(III) and copper(II) by reversed-phase paired-ion chromatography

Trans-1,2-cyclohexanediaminetetra-acetic acid (DCTA) chelates of bismuth(III), iron(III) and copper(II) have been separated by two techniques using reversed-phase paired-ion chromatography. In one, the chelates in aqueous solution were separated within 20 min on a 6.0 × 300 mm ERC-ODS column with 10⁻²M tetrabutylammonium ion (TBA⁺) in methanoi-water mixture (45:55 v/v) as eluent. In the other, the metal ions in aqueous solution were separated within 10 min by direct injection into an ERC-ODS column with 10⁻²M TBA⁺/10⁻³M DCTA in methanoi-water mixture (40:60 v/v) as eluent.     

Polarographic determination of proguanil and chlorhexidine

The method is based on the cathodic wave obtained for chlorhexidine and proguanil in buffered aqueous dimethylformamide media. Concentrations up to 8 × 10⁻⁵ and 6 × 10⁻⁴M, respectively, can be determined. The difference in behaviour at various pH values or in the presence of surface-active agents, is useful for characterization of both biguanides.     

Simultaneous determination of selenium and lead in whole blood samples by differential pulse polarography

The polarographic reduction of lead in the presence of selenite gives rise to an additional peak corresponding to the reduction of lead (Pb) on adsorbed selenium (Se) on mercury at −0.33 V. The selenium and lead content can be determined using this peak by the addition of a known amount of one of these ions first and then the second ion. The linear domain range of lead is 5.0×10⁻⁷–2.0×10⁻⁵ M and for selenium 5.0×10⁻⁷–1.0×10⁻⁵ M. Using this method 4.90×10⁻⁷ M Se(IV) and 1.47×10⁻⁶ M Pb(II) in a synthetic sample could be determined with a relative error of +2.0% and 1.8%, respectively (n=4). A recovery test after acid digestion for a synthetic sample was 97% for selenium and 96.5% for lead. The method was applied to 1 ml of digested blood, and 328±23 μg l⁻¹ Se(IV) and 850±62 μg l⁻¹ Pb(II) could be determined with a 90% (n=5) confidence interval.     

Photometric determination of micro amounts of thiosulphate by means of its cyanolysis with lanthanum(III) as catalyst

Lanthanum(III) has been found to catalyse the reaction of thiosulphate with cyanide. The effects of pH, reaction time and temperature, amount of cyanide and lanthanum, and order of addition of reagents have been investigated. Temperature has little effect in the range 10–30°, but at both 35° and 40° the rate is noticeably faster. Reaction is complete at room temperature in 1.5 hr at pH 9.3–9.6, and in 3 hr at pH 9.1–9.6. The method can be applied to the determination of 1.0 × 10⁻⁵−6.0 × 10⁻⁴M thiosulphate, with a relative standard deviation of 0.3% for 4 × 10⁻⁴M thiosulphate.     

Flow-injection chemiluminescence determination of tetracyclines with in situ electrogenerated bromine as the oxidant

By designing a novel flow-through electrolytic cell (FEC), bromine was produced near to the surface of the platinum electrode by electrochemical oxidation of acidic KBr. The fast and weak chemiluminescence signal produced by the chemical reaction of the electrogenerated bromine with H₂O₂ was greatly enhanced by tetracyclines Based on these observations, a new, sensitive and simple electrogenerated chemiluminescence (ECL) method for the determination of tetracyclines was developed. Under the optimum experimental conditions, the calibration graphs are linear over the range 3.0×10⁻⁸ to 5.0×10⁻⁵ g ml⁻¹ for tetracycline, 2.0×10⁻⁷ to 2.4×10⁻⁵ g ml⁻¹ for oxytetracycline and 1.0×10⁻⁷ to 5.0×10⁻⁵ g ml⁻¹ for chlortetracycline. The limits of detection (S/N=3) are 1.0×10⁻⁸ g ml⁻¹ for tetracycline, 7.0×10⁻⁸ g ml⁻¹ for oxytetracycline and 1.5×10⁻⁷ g ml⁻¹ for chlortetracycline. For the determination 5.0×10⁻⁷ g ml⁻¹ tetracycline, the relative standard deviation was <5%. The proposed method was used to determine tetracyclines in pharmaceutical formulations.     

Potentiometric titration of sulphate, sulphite and dithionate mixtures, with use of a lead ion-selective electrode

Simple methods are described for the analysis of sulphate, sulphite and dithionate mixtures by potentiometric titration with lead perchlorate (and use of a lead ion-selective electrode). The error and precision are both about 2–5% for the sulphate concentration range 3 × 10⁻³ −6 × 10⁻⁴M. The sulphur content in fuels derived from refuse was determined by potentiometric titration after bomb-combustion and the results compared favourably with those from the standard BaSO₄ gravimetric method.     

Direct determination of sub-nanomolar levels of zinc in sea-water by cathodic stripping voltammetry

A novel technique for the determination of nanomolar levels of zinc in aqueous solution is presented. The zinc complex with ammonium pyrrolidine dithiocarbamate is adsorbed on a hanging mercury-drop electrode and the reduction current of zinc is measured by voltammetry. The detection limit for zinc is 3 × 10⁻¹¹M, with 10-min collection time. A procedure is suggested for the simultaneous determination of Ni and Zn in a single sample.     

Applications of enzyme-catalysed reactions in trace analysis-II Determination of cyanide, sulphide, and iodine with invertase

Methods are described for the determination of cyanide (10⁻⁸–10⁻⁵M and sulphide (10⁻⁷–10⁻⁵ M) based on the de-inhibitory effect of these ions on invertase inhibited by mercury(II) or by silver. Iodine (0.1–3 μg) may be determined by its inhibition of invertase.     

The effect of trace levels of cyanide on the formation of mercury-iodide complexes

The interference of trace levels of cyanide with the formation of iodo-mercury complexes is made the basis of a method of trace analysis for cyanide. The decrease in absorbance of the iodo-mercury complexes is a linear function of total cyanide concentration up to about 5 × 10⁻⁵M in 0.1M sodium hydroxide medium when the iodide and mercury total concentrations are 0.05M and 3 × 10⁻⁵M respectively. Several cyano-mercury complexes are formed simultaneously, and quite a large fraction of the cyanide remains uncomplexed.     

Electroreduction and determination of Pipril (Piperacillin) in both aqueous and biological samples

The electrochemical behavior of the relatively new antibacterial antibiotic Pipril (Piperacillin) at the dropping mercury electrode is investigated using both direct current polarography (DCP) and differential pulse polarography (DPP). At the hanging mercury electrode (HMDE), the reduction mechanism has been elucidated using cyclic voltammetric technique in the pH range from 2 to 10. The effect of some metal ions, e.g. Cu(II) and Pb(II) has been also tested. Determination of the drug using adsorptive stripping analysis was assessed in both aqueous and urine samples. The effect of the different experimental parameters affecting the drug determination, e.g. pH, supporting electrolyte nature, accumulation potential, accumulation time and other operational parameters are also mentioned. Detection limits of 5 × 10⁻⁹ and 1 × 10⁻⁸M Pipril in aqueous and urine samples, respectively, are achieved.     

On-line extraction-spectrophotometric determination of neostigmine in pharmaceuticals using double membrane phase separator and monovalent dyestuff

A simple, sensitive and rapid spectrophotometric method for the determination of neostigmine by flow injection analysis (FIA) coupled with an ion associate extraction has been developed. The three-line manifold was assembled. Neostigmine(200 μl) was injected into a distilled water stream and the pH was adjusted to 10 with a borate–phosphate buffer solution. Then, the stream was mixed with the ion-pairing tetrabromophenolphthalein ethylester (TBPEH)-1,2-dichloroethane solution. After phase separation with a double membrane phase separator, absorbance was measured at 610 nm. A linear calibration graph was obtained between 1×10⁻⁷ mol l⁻¹ and 5×10⁻⁷ mol l⁻¹ of neostigmine. Up to 48 samples h⁻¹ could be processed with a relative standard deviation (R.S.D.) of 0.5% (n=5) for 4×10⁻⁷ mol l⁻¹ neostigmine. The proposed system was applied to the simple, reproducible and rapid determination of neostigmine in commercial pharmaceuticals.     

Applications of enzyme-catalysed reactions in trace analysis-III Determination of silver and thiourea by their combined inhibition of invertase

Thiourea has been found to enhance the inhibition of invertase by silver ions. The effect is applied to the determination of 1–5 × 10⁻⁷ M silver and of 10⁻⁷–10⁻⁸ M thiourea. A mechanism is suggested for the enhancement.     

Simultaneous potentiometric determination of ClO(3)(-)-ClO(2)(-) and ClO(3)(-)-HClO by flow injection analysis using Fe(III)-Fe(II) potential buffer

A rapid potentiometric flow injection technique for the simultaneous determination of oxychlorine species such as ClO₃⁻–ClO₂⁻ and ClO₃⁻–HClO has been developed, using both a redox electrode detector and a Fe(III)–Fe(II) potential buffer solution containing chloride. The analytical method is based on the detection of a large transient potential change of the redox electrode due to chlorine generated via the reaction of the oxychlorine species with chloride in the potential buffer solution. The sensitivities to HClO and ClO₂⁻ obtained by the transient potential change were enhanced 700–800-fold over that using an equilibrium potential. The detection limit of the present method for HClO and ClO₂⁻ is as low as 5×10⁻⁸ M with use of a 5×10⁻⁴ M Fe(III)–1×10⁻³ M Fe(II) buffer containing 0.3 M KCl and 0.5 M H₂SO₄. On the other hand, sensitivity to ClO₃⁻ was low when a potential buffer solution containing 0.5 M H₂SO₄ was used, but could be increased largely by increasing the acidity of the potential buffer. The detection limit for ClO₃⁻ was 2×10⁻⁶ M with the use of a 5×10⁻⁴ M Fe(III)–1×10⁻³ M Fe(II) buffer containing 0.3 M KCl and 9 M H₂SO₄. By utilizing the difference in reactivity of oxychlorine species with chloride in the potential buffer, a simultaneous determination method for a mixed solution of ClO₃⁻–ClO₂⁻ or ClO₃⁻–HClO was designed to detect, in a timely manner, a transient potential change with the use of two streams of potential buffers which contain different concentrations of sulfuric acid. Analytical concentration ranges of oxychlorine species were 2×10⁻⁵–2×10⁻⁴ M for ClO₃⁻, and 1×10⁻⁶–1×10⁻⁵ M for HClO and ClO₂⁻. The reproducibility of the present method was in the range 1.5–2.3%. The reaction mechanism for the transient potential change used in the present method is also discussed, based on the results of batchwise experiments. The simultaneous determination method was applied to the determination of oxychlorine species in a tap water sample, and was found to provide an analytical result for HClO, which was in good agreement with that obtained by the o-tolidine method and to provide a good recovery for ClO₃⁻ added to the sample.     

Simultaneous potentiometric and fluorimetric determination of diclofenac in a sequential injection analysis system

Two independent methods for the determination of diclofenac were simultaneously implemented in an automated analytical system, based on the concept of sequential injection analysis, providing real-time assessment of results quality. The potentiometric detection was carried out with an ion-selective electrode based on a cyclodextrin while for the fluorimetric determination the sample was previously subject to in-line irradiation with UV light. The potentiometric and photochemical-fluorimetric determinations exhibited linear working ranges of 5×10⁻⁶ to 1×10⁻² and 1×10⁻⁶ to 1×10⁻⁴ mol dm⁻³, respectively. Relative standard errors of 0.5% for the potentiometric determination and 0.6% for the photochemical-fluorimetric determination were obtained after 10 consecutive injections of a 5×10⁻⁵ mol dm⁻³ diclofenac standard solution. The sampling rate was about 32 samples h⁻¹. Both methods were applied in the analysis of pharmaceutical formulations. The quality of results obtained was evaluated by comparison to the reference method, with no statistically significant differences for a 95% confidence level.     

Flow-injection potentiometric determination of triiodide by plasticized poly(vinyl chloride) membrane electrodes and its application to the determination of chlorine-containing disinfectants

Plasticized poly(vinyl chloride) (PVC) membranes of different compositions were tested for use in the construction of potentiometric flow detectors for triiodide. A membrane with a 2:1 (w/w) 2-nitrophenyl octyl ether to PVC ratio was selected. The influence of thiosulphate in the carrier solution composition and of the flow-injection variables on the determination of triiodide was studied. In the selected conditions, a linear relationship between peak height and log[I₃⁻] was obtained between 5 × 10⁻⁶ and 1 × 10⁻⁴ mol l⁻¹ triiodide. Peak height relative standard deviations for 2 × 10⁻⁵ and 1 × 10⁻⁴ mol l⁻¹ triiodide were ±0.4 and ±1.8%, respectively, and sampling frequency was 80 samples per hour. The method proposed was applied satisfactorily to the iodometric determination of different chlorine-containing disinfectants, among them trichloroisocyanuric acid and dichloroisocyanurate in several types of commercial sample.     

Unsegmented flow analysis with ion-selective electrodes by use of a large-volume wall-jet cell Continuous electrode reactivation in the determination of fluoride and chloride

A simple, large-volume wall-jet cell was designed for unsegmented flow analysis. The working electrode is immersed in a solution that reactivates the electrode surface. During the sample measurement, the working electrode is screened from the reactivation solution by the streaming sample solution; between the individual samples, air is pumped through the jet and agitates the reactivating solution at the electrode surface. The properties of the cell were investigated with the fluoride and chloride ion-selective electrodes and the method was applied to determination of fluoride and chloride in steel corrosion products and in a reference sample of the fly dust from electric-arc furnaces. The method permits about 90 measurements per hour, the results are reproducible and the limits of determination (6.3 × 10⁻⁸ and 2.3 × 10⁻⁷M for fluoride and chloride, respectively) are substantially lower than the values commonly obtained in batch experiments. At least 150 measurements can be carried out without significant changes in the reliability of determination and the reactivation solution can then be replaced.     

Determination of germanium by potentiometric stripping analysis and adsorption potentiometric stripping analysis

Potentiometric stripping analysis was applied to determination of germanium(IV) in 0.2M NH₃-NH₄Cl (pH 8.4) buffer solution at −1.8 V (vs. Ag/AgCl), with dissolved oxygen or Hg(II) as oxidant. The sensitivity was 8.5 × 10⁻⁹M in the presence of 2.0 × 10⁻⁵M Hg(II) with plating for 15 min after deaeration for 20 min. Cyclic voltammetry revealed that GE(IV) å Ge at the surface of the mercury-film electrode in a one-step irreversible reduction reaction, and the Ge at the electrode was oxidized by dissolved oxygen in the solution. The presence of complexing agents such as Alizarin Red (ARS), which forms a Ge(IV) complex adsorbed at the electrode, improved the sensitivity by one order of magnitude. The presence of adsorption was revealed by the temperature coefficient, the electrocapillary curve and cyclic voltammetry. Ge-containing samples were analysed by the proposed methods and agreement with the results obtained by other methods was excellent.     

Time measurement-visual analysis of nickel(II) using autocatalytic reaction with sodium sulfite/hydrogen peroxide system and its application to the length detection-flow analysis

Trace amounts of nickel(II) can function as a trigger (=reaction initiator) in an autocatalytic reaction with the sodium sulfite/hydrogen peroxide system. Based on this finding, sub-μg L⁻¹ levels of nickel(II) were determined by a time measurement using the autocatalytic reaction. The detection range using the above method was 10⁻⁹–10⁻⁵ M, the detection limit (3σ) was 8.1 × 10⁻¹⁰ M (0.047 μg L⁻¹), and the relative standard deviation was 2.66% at nickel(II) concentration of 10⁻⁷ M (n = 7). This method was applied to length detection-flow injection analysis. The detection range for the flow injection analysis was 2 × 10⁻⁹–2 × 10⁻³ M. The detection limit (3σ) was 1.4 × 10⁻⁹ M (0.082 μg L⁻¹), and the relative standard deviation was 1.86 at initial nickel(II) concentration of 10⁻⁶ M (n = 7).