Low temperature synthesis of Co<Subscript>2</Subscript>SiO<Subscript>4</Subscript>/SiO<Subscript>2</Subscript> nanocomposite using a modified sol–gel method

The paper presents a study on the preparation of Co₂SiO₄/SiO₂ nanocomposites by a new modified sol–gel method. We have prepared gels starting from tetraethylorthosilicate (Si(OC₂H₅)₄), cobalt nitrate Co(NO₃)₂·6H₂O and some diols: ethylene glycol (C₂H₆O₂), 1,2propanediol (C₃H₈O₂) and 1,3propanediol (C₃H₈O₂), for a final composition: 30% CoO/70% SiO₂. During the heating of the gels at 140 °C, a redox reaction takes place between NO₃ ⁻ ions and diol with formation of some carboxylate anions. These carboxylate anions react with the Co(II) ions to form coordination compounds embedded in silica matrix, as evidenced by FT-IR spectrometry and thermal analysis. These Co(II) coordinative compounds thermally decompose in the range 250–300 °C to the corresponding oxides: CoO and/or Co₃O₄ inside the matrices pores. When CoO results, it reacts with SiO₂ at low temperature leading to Co₂SiO₄, which crystallizes at 700 °C. XRD patterns of the samples annealed at temperatures lower than 700 °C were characteristic to amorphous phases. The samples annealed at temperatures ≥700 °C, contain Co₂SiO₄ (olivine) as unique crystalline phase inside the amorphous silica matrix, according to XRD patterns. As evidenced by TEM images, Co₂SiO₄ nanoparticles are homogenously dispersed inside the silica matrix.     

Phosphorus modified MoO<Subscript>3</Subscript>–Bi<Subscript>2</Subscript>SiO<Subscript>5</Subscript>/SiO<Subscript>2</Subscript> catalyst for gas-phase epoxidation of propylene by molecular oxygen

The phosphorus (P) modified MoO₃–Bi₂SiO₅/SiO₂ catalyst was prepared by a simple co-impregnation method and investigated in the epoxidation of propylene by molecular oxygen. The catalyst was characterized by X-ray diffraction (XRD), N₂ adsorption–desorption analysis, NH₃-temperature-programmed desorption (NH₃-TPD), transmission electron microscopy, and Raman spectroscopy. It was found that the P-modified MoO₃–Bi₂SiO₅/SiO₂ catalyst with a P/Mo molar ratio of 0.5 exhibits the best catalytic performance for epoxidation of propylene by O₂, the TOFs for propylene oxide (PO) formation was four times higher than that of the unmodified one at 633 K. The modification by P could promote the dispersion of MoO₃ nanoparticles and increase the number of weak and moderate acid sites with respect to the phosphorus-free MoO₃–Bi₂SiO₅/SiO₂ catalyst, which were beneficial to the formation of PO. Moreover, the introduction of P also could protect the mesoporous structure by inhibiting the formation of Bi₂Mo₃O₁₂, which was beneficial to the dispersion of active species. We suppose that the phosphorus, bismuth and molybdenum species of P-modified MoO₃–Bi₂SiO₅/SiO₂ catalyst play important roles for propylene epoxidation by molecular oxygen.     

Effects of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> on the crystallization and structure of CaO–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> glass ceramics

Radiation-induced degradation of the weakly and strongly 4-vinylpyridine basic ion exchange resins by gamma radiolysis was investigated in the presence of air and liquid water. This study is focused on evaluating the radiolytic gases (H₂, CO, CO₂ and CH₄) and liquid products (water-solute TOC and NH₄ ⁺). The weakly basic resin yielded lower amounts of H₂ and CO and higher amounts of CO₂ than those of the strongly basic resin. Moreover, the strong basic resin tended to yield greater amounts of NH₄ ⁺. Resins were characterized by the FTIR spectroscopy technique and the results showed that the resins structures are relatively stable.     

Sol–Gel Derived Rh/TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> Nanocomposite Membranes

A porous borosilicate substrate has been coated with base catalysed SiO₂ sol–gel nanoparticles. Onto these were deposited the vapour of titanium isopropoxide, where it reacted with the surface OH groups to give a TiO₂-overcoat. This nanocomposite sol–gel derived TiO₂/SiO₂ membrane was then doped with 1%Rh giving Rh/TiO₂/SiO₂ membranes. These are shown to be coherent and crack-free, to have good permeability and activity in the isomerisation of butanes. It appears that sol–gel chemistry will allow such membranes to be totally engineered at a nm level.     

Synthesis and photocatalytic activity of mesoporous SiO<Subscript>2</Subscript>–TiO<Subscript>2</Subscript>

Mesoporous SiO₂–TiO₂ was synthesized by the sol–gel method using Si(OC₂H₅)₄, Ti(OC₂H₅)₄, and stearyltrimethylammonium chloride. By using acetylacetone as the capping agent of Ti(OC₂H₅)₄, homogeneous SiO₂–TiO₂ composite was obtained. Spherical mesoporous SiO₂–TiO₂ was also synthesized by the sol–gel method using W/O emulsion under microwave irradiation. The specific surface area of these mesoporous SiO₂–TiO₂ materials decreased when the Ti/Si molar ratio was higher than 0.1, which indicated that Ti was homogeneously distributed in mesoporous SiO₂ matrix at Ti/Si ≦ 0.1. The photocatalytic activity of mesoporous SiO₂–TiO₂ materials was investigated by the degradation of methylene-blue in water under UV light irradiation. Mesoporous SiO₂–TiO₂ was effective for the adsorption–decomposition of methylene-blue.     

Modifying additives affect the properties of Y<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> system

The effects caused by modifying additives, namely nonionic surfactants (Tween 80 and Neonol AF 9-6) and oxides (B₂O₃ and HfO₂), on the rheology, film formation, and phase formation in the yttrium aluminum silicate system prepared by sol–gel technology were studied. The effect of 1 wt % HfO₂ additions on the activation energy of crystallization was studied.     

Synthesis of ZrO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> and ZrO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript>–Cu(II) xerogels by joint hydrolysis in an aqueous ammonia atmosphere

ZrO₂–SiO₂ xerogels have been synthesized through hydrolysis of a mixture of tetrabutoxyzirconium and tetraethoxysilane in a desiccator in a vapor of a 15% aqueous NH₃ atmosphere. ZrO₂–SiO₂–Cu(II) xerogels were synthethized analogously through joint hydrolysis of a mixture of the organometallic precursors and copper(II) chloride. The effect of synthesis conditions on the physical and chemical properties of the resulting material has been studied.     

Preparation and characterization of nanocrystalline CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> deposited on SiO<Subscript>2</Subscript>: in situ sol–gel process

In situ base catalyst assisted sol–gel process is used for the synthesis of nanocrystalline CoFe₂O₄ deposition on SiO₂ particles. The SiO₂ particles were prepared using base catalyst assisted sol–gel process and the consecutive formation and deposition of nanocrystalline CoFe₂O₄ on SiO₂ particles was monitored using Powder X ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Thermo Gravimetric And Differential Thermal Analysis (TG/DTA), Scanning Electron Microscopy and Energy Dispersive X ray Spectroscopy (SEM–EDS) and High Resolution Transmission Electron Microscopy (HRTEM). The crystallite size of CoFe₂O₄ is calculated using Scherrer’s formula and it is found to be 8 nm. The HRTEM images and selective area electron diffraction (SAED) results confirmed the formation of nanocrystalline CoFe₂O₄ particles deposited over SiO₂ spheres.     

Synthesis and properties of magnetic superhydrophobic mesoporous Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> composites

Ways to obtain Fe₂O₃–SiO₂ iron-containing silica composites with organized mesoporous structure (MCM-41) and large specific surface area (up to 1476 m² g^–1) were considered. The influence exerted by the method used to synthesize the materials on their structure, texture characteristics, particle size, and magnetic properties were studied. The aggregative stability of samples was examined. It was shown that treatment of the resulting composites with compounds from the chlorosilane group affects their hydrophobic properties.     

TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> hard coating on polycarbonate substrate by microwave assisted sol–gel technique

To enhance the poor scratch resistance of polycarbonate, a silica (SiO₂) and titania (TiO₂) transparent inorganic coatings was designed and synthesized using a microwave assisted sol–gel heating. Due to the transparency of PC to microwave, the idea was to obtain a localized heating only on the coating film. The obtained films were fully characterized to mainly evaluate the effect of titania content, added both as nanoparticles and from tetraethyl orthotitanate, TEOT, on scratch resistance and surface morphology. Particular attention was paid to preserve the transparency of the final product. The results allowed to define that TEOT addition enhances the adhesion between coating and polycarbonate, even if the optimized quantity have to be defined in order to avoid a decrease of coating mechanical resistance. In this work optimized TEOT level results to be the associated to 5 wt% of TiO₂, which enable the better balancing between adhesion and mechanical resistance performances.     

Calorimetric studies on 2TeO<Subscript>2</Subscript>–V<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

Glasses of the composition 2TeO₂–V₂O₅ were fabricated via the conventional melt-quenching technique. The amorphous and the glassy nature of the as-quenched samples were confirmed by X-ray powder diffraction (XRD) and differential scanning calorimetry (DSC), respectively. The glass transition and crystallization parameters were evaluated under non-isothermal conditions using DSC. X-ray diffraction studies confirmed the presence of partially oriented crystallites in the heat-treated glasses. Kauzmann temperature (lower bound for the kinetically observed glass transition) was deduced from the heating rate dependent glass transition and crystallization temperatures.     

Enhanced photocatalytic activities of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> nanohybrids immobilized on cement-based materials for dye degradation

Using cement-based material as a matrix for photocatalytic hybrids is an important development for the large-scale application of photocatalytic technologies. In this work, photocatalytic activity of nanosized hybrids of TiO₂/SiO₂ (nano-TiO₂–SiO₂) for degradation of some organic dyes on cementitious materials was highlighted. For this purpose, an optimal inorganic sol–gel precursor was firstly applied to prepare the composites of nano-TiO₂–SiO₂ which was characterized by XRD, SEM and UV–Vis. Then, a thin layer was successfully coated on white Portland cement (WPC) blocks using a dipping process in a nano-TiO₂–SiO₂ solution. The effect of nano-TiO₂–SiO₂-coated WPC blocks on photocatalytic decomposition of three dyes, including Malachite green oxalate (MG), Methylene blue (MB) and Methyl orange (MO) were studied under UV irradiation and monitored by chemical oxygen demand tests. The results showed an increase in photocatalytic effects which depends on the structure and pH of the applied cement.     

Mass attenuation coefficients of B<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript>–CaF<Subscript>2</Subscript> glass system at 0.662 and 1.25 MeV gamma energies

The total mass attenuation coefficients, partial interaction and the effective atomic numbers (Z_eff) of glass system (80−x)B₂O₃–10Al₂O₃–10SiO₂–xCaF₂ (where x = 5, 10, 20, 25, 30, 35 and 40 mol %) have been calculated at photon energies 0.662 and 1.25 MeV using the WinXCom software on the basis of mixture rule. Results indicated that the total mass attenuation coefficients showed a decrease with increasing the CaF₂ concentration, due to a decrease in Compton scattering probability, which gave a dominant contribution to the total mass attenuation coefficients for the studied glass samples at both energies. However, the photoelectric absorption and coherent scattering showed an increase with increasing the CaF₂, concentrations at same energies. For a comparison, the total mass attenuation coefficients of the glass system had lower values at the energy 1.25 MeV than that at 0.662 MeV. Z_eff was found to increase linearly with the increase of CaF₂ concentrations. It was concluded that low CaF₂ concentrations in glass system, under study, have Z_eff close to that of human tissue and have higher total absorption coefficients at energy of 0.662 MeV than that at 1.25 MeV. These results are very useful in designing gamma radiation detectors using thermoluminescence technique. Therefore, it is recommended to use low CaF₂ concentration of our glass system as good gamma detectors at energy of 1.25 MeV.     

Crystal structure of Ba<Subscript>3</Subscript>[UO<Subscript>2</Subscript>(C<Subscript>2</Subscript>O<Subscript>4</Subscript>)<Subscript>2</Subscript>(NCS)]<Subscript>2</Subscript> · 9H<Subscript>2</Subscript>O

Single crystals of Ba₃[UO₂(C₂O₄)₂(NCS)]₂ · 9H₂O are synthesized and studied by X-ray diffraction. The crystals are orthorhombic, space group Fddd, Z = 16, and the unit cell parameters are a = 16.253(3) Å, b = 22.245(3) Å, c = 39.031(6) Å. The main crystal structural units are mononuclear complex groups [UO₂(C₂O₄)₂NCS]^3? of the crystal-chemical family (AB ₂ ⁰¹ M¹ (A = UO ₂ ²⁺ , B⁰¹ = C₂O ₄ ^2? , M¹ = NCS^?) of the uranyl complexes linked into a three-dimensional framework by electrostatic interactions and hydrogen bonds involving oxalate ions and water molecules.     

Crystal structure of Cs[(UO<Subscript>2</Subscript>)<Subscript>2</Subscript>(C<Subscript>2</Subscript>O<Subscript>4</Subscript>)<Subscript>2</Subscript>(OH)] · H<Subscript>2</Subscript>O

Single crystals of Cs[(UO₂)₂(C₂O₄)₂(OH)] · H₂O were synthesized and structurally studied using X-ray diffraction. The compound crystallizes in monoclinic space group P2₁/m, Z = 2, with the unit cell parameters a = 5.5032(4) Å, b = 13.5577(8) Å, c = 9.5859(8) Å, β = 97.012(3)°, V = 709.86(9) ų, R = 0.0444. The main building units of crystals are [(UO₂)₂(C₂O₄)₂(OH)]^? layers of the A₂K ₂ ⁰² M² (A = UO ₂ ²⁺ , K⁰² = C₂O ₄ ^2? , and M² = OH^?) crystal-chemical family. Uranium-containing layers are linked into a three-dimensional framework via electrostatic interactions with outer-sphere cations and hydrogen bonds with water molecules.     

Physicochemical properties of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> xerogel modified by hydrogen peroxide

How the specific surface area and the amorphous-to-crystalline titania phase ratio in TiO₂–SiO₂ (14 mol % TiO₂) xerogels change during the fivefold repeated cycles comprising the hydrogen peroxide treatment of the xerogel followed by drying and calcining of the binary material, was traced by the BET method, X-ray powder diffraction, and IR spectroscopy.     

Lanthanide-Organic Frameworks Based on {Ln<Subscript>4</Subscript>(μ<Subscript>3</Subscript>-OH)<Subscript>4</Subscript>(μ<Subscript>2</Subscript>-OH)<Subscript>2</Subscript>} Cluster Units

Abstract  

Three novel lanthanide-organic frameworks: [Ln₂(pyba)₃(μ₃-OH)₂(μ₂-OH)(H₂O)] _n (Ln = Er (1), Y (2), Dy (3) Hpyba = 4-pyridin-4-yl-benzoic acid) have been hydrothermally synthesized and structurally characterized by single crystal X-ray diffraction. Structure analysis shows that each {Ln₄(μ₃-OH)₄(μ₂-OH)₂} cluster units interconnect to form 1-D chains, which are further linked by π–π interactions to make a 3-D supramolecular network structure. Furthermore, the IR, PXRD and TGA of compounds 1–3 were also studied.     

Preparation,characterization and catalytic studies of V<Subscript>2</Subscript>O<Subscript>5</Subscript>–SiO<Subscript>2</Subscript> xerogel composite

In this work, we report the synthesis, characterization and catalytic properties of a vanadium oxide–silicon oxide composite xerogel prepared by a soft chemistry approach. In order to obtain such material, we submitted a vanadium pentoxide gel previously synthesized via protonation of metavanadate species to an “in situ” progressive polycondensation into silica gel. The material has been characterized by X-ray diffraction, infrared spectroscopy, thermogravimetric analysis and scanning electron microscopy. Further, the catalytic activity of this material was evaluated for the epoxidation of styrene and cyclooctene using iodosylbenzene, hydrogen peroxide and m-chloroperbenzoic acid as the oxidizing agent.     

Structural characterisation and thermo-physical properties of glasses in the Li<Subscript>2</Subscript>O–SiO<Subscript>2</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–K<Subscript>2</Subscript>O system

This article aims to shed some light on the structure and thermo-physical properties of lithium disilicate glasses in the system Li₂O–SiO₂–Al₂O₃–K₂O. A glass with nominal composition 23Li₂O–77SiO₂ (mol%) (labelled as L₂₃S₇₇) and glasses containing Al₂O₃ and K₂O with SiO₂/Li₂O molar ratios (3.13–4.88) were produced by conventional melt-quenching technique in bulk and frit forms. The glass-ceramics (GCs) were obtained from nucleation and crystallisation of monolithic bulk glasses as well as via sintering and crystallisation of glass powder compacts. The structure of glasses as investigated by magic angle spinning-nuclear magnetic resonance (MAS-NMR) depict the role of Al₂O₃ as glass network former with four-fold coordination, i.e., Al(IV) species while silicon exists predominantly as a mixture of Q ³ and Q ⁴ (Si) structural units. The qualitative as well as quantitative crystalline phase evolution in glasses was followed by differential thermal analysis (DTA), X-ray diffraction (XRD) adjoined with Rietveld-reference intensity ratio (R.I.R.) method, Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The possible correlation amongst structural features of glasses, phase composition and thermo-physical properties of GCs has been discussed.     

Novel sol–gel method for preparation of high concentration ε-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/SiO<Subscript>2</Subscript> nanocomposite

ε-Fe₂O₃/SiO₂ nanocomposite was prepared by novel solgel method using single precursor for both nanoparticles and matrix. This method allows to prepare the samples free of α-Fe₂O₃ with 40% of Fe₂O₃ in SiO₂. Nanoparticles of 12 nm diameter were obtained by annealing at 1,000 °C. The samples were characterized by powder X-ray diffraction and transmission electron microscopy. Mössbauer spectroscopy identified ε-Fe₂O₃ as the only magnetically ordered phase at room temperature. Magnetic measurements revealed progressive necking of hysteresis loops measured at 300 and 2 K. In both cases the intrinsic coercivity reaches only 0.25 T. Measurements up to 14 T shows monotonous decreasing trend of saturated magnetization with increasing temperature.