Co_3O_4纳米片的制备及对H_2O_2电还原反应的催化性能

通过恒电势电沉积和加热处理在泡沫镍基体上制备了Co3O4纳米片.利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射(XRD)、傅里叶变换红外光谱(FTIR)和X射线光电子能谱(XPS)等手段对纳米片的形貌和结构进行了表征.采用线性伏安扫描和计时电流技术研究了Co3O4纳米片电极对H2O2的电还原性能.结果表明,在3.0 mol/L KOH和0.4 mol/L H2O2溶液中,当电压为-0.4 V(vs.Ag/AgCl)时,线性伏安扫描电流密度达到-0.386 A/cm2,在1000 s测试时间内,计时电流密度衰减很小,表明Co3O4纳米片电极对H2O2具有很高的活性和稳定性.     

Co3O4纳米片的制备及对H2O2电还原反应的催化性能简

通过恒电势电沉积和加热处理在泡沫镍基体上制备了Co3O4纳米片. 利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射(XRD)、傅里叶变换红外光谱(FTIR)和X射线光电子能谱(XPS)等手段对纳米片的形貌和结构进行了表征. 采用线性伏安扫描和计时电流技术研究了Co3O4纳米片电极对H2O2的电还原性能. 结果表明,在3.0 mol/L KOH 和 0.4 mol/L H2O2溶液中,当电压为-0.4 V(vs. Ag/AgCl)时,线性伏安扫描电流密度达到-0.386 A/cm2,在1000 s 测试时间内,计时电流密度衰减很小,表明Co3O4纳米片电极对H2O2具有很高的活性和稳定性.     

电化学方法制备石墨烯-铁氰化镍复合物及对抗坏血酸的电催化氧化研究

采用电化学还原方法制备了铁氰化镍-石墨烯复合薄膜电极,扫描电子显微镜(SEM)表征电还原石墨烯和铁氰化镍-石墨烯复合材料的表面形貌。采用循环伏安和计时电流技术研究了该修饰电极对抗坏血酸(AA)的电催化氧化性能,据此建立了一种测定AA的电化学分析新方法。由于石墨烯和铁氰化镍纳米颗粒之间的协同效应,使得该复合修饰电极对抗坏血酸具有优异的电催化活性。在0.1 mol/L pH 7.00的PBS溶液中,抗坏血酸的催化氧化电流与其浓度在1.0×10-4~7.0×10-4mol/L范围内呈良好的线性关系,检出限为3.1×10-5mol/L(S/N)。     

聚黄苓苷/还原氧化石墨烯修饰电极的制备及对羟胺的检测

通过电聚合的方法制备了聚黄苓苷/还原氧化石墨烯修饰电极,采用扫描电子显微镜和循环伏安法对制备的电极进行了表征和研究。结果表明:该修饰电极对羟胺具有明显的电催化作用。采用计时电流技术对羟胺进行检测,在1.0×10~(-7)~1.1×10~(-4)mol/L的浓度范围内,羟胺的计时电流响应信号和其浓度成良好的线性关系,检测限为52 nmol/L(S/N=3)。该修饰电极能够用于羟胺的样品分析。     

PB/Au/CILE的制备与应用

混合离子液体(N-丁基吡啶六氟磷酸盐,[BuPy][PF6])与石墨粉,制备了离子液体碳糊电极(CILE),再采用电沉积法制得PB/Au/CILE修饰电极,研究了该修饰电极的电化学行为及其对H2O2的电催化,建立了H2O2的计时安培测定新方法。结果表明:在该修饰电极上PB产生了一对准可逆的氧化还原峰,并对H2O2表现出良好电催化作用,安培法测定H2O2的线性范围为5.0×10-6～1.55×10-4mol/L,检出限为1.0×10-6mol/L(S/N=3)。连续10次测定5.0×10-6mol/L H2O2峰电流的RSD为2.1%。     

苯甲酰肼在多壁碳纳米管修饰玻碳电极上的电催化氧化及其电化学动力学性质

研究了苯甲酰肼(BH)在MWCNT/GCE上的电化学行为。实验结果表明,BH在GCE上的直接电化学氧化十分迟缓,无氧化峰出现,但在MWCNT/GCE上BH在0.20 V处出现了一个不可逆氧化峰,且峰电流大幅度增大,表明MWCNT/GCE对BH电化学氧化具有良好的催化作用。同时用计时库仑法(Chro-nocoulometry,CC)和计时电流法(Chronoamperometry,CA)测定了电极过程动力学参数:扩散系数D=8.73×10-5cm2.s-1,电子转移系数α=0.85,电极反应速率常数kf=1.45×10-3s-1。稳态电流-时间实验结果表明,电流响应信号随其浓度成比例增长,响应时间小于6 s,最低响应浓度为1×10-6mol/L。该方法可用于BH电化学定量测定。     

光催化还原制备Au/Ag核壳结构纳米粒子及其修饰电极的电催化性能

以Keggin结构硅钨杂多酸H4SiW12O40(SiW12)为光催化还原剂,通过光化学还原法制备Au/Ag核壳结构纳米粒子. 透射电子显微镜分析显示,所得纳米粒子粒径为30～40 nm,呈均匀分散的球形颗粒,该制备方法的特点是可以较好的避免单金属纳米粒子的形成. 将Au/Ag核壳纳米粒子修饰到具有PVP膜的玻碳电极表面,得到SiW12-(Au/Ag)-PVP多层膜修饰电极. 该修饰电极在0.5 mol/L H2SO4介质中具有良好的电化学响应,在0～-0.75 V电位范围内,出现了3对归属于SiW12的氧化还原峰,且电极性能稳定,灵敏度高. 对H2O2的电催化还原性能明显优于单金属Ag纳米粒子修饰电极,说明Au核的存在可以很好的改善Ag的电催化性能,Au和Ag之间存在相互协同催化作用.     

二氧化铅修饰玻碳电极的镀膜/循环伏安法制备及电催化性能

采用镀膜/循环伏安法制备了PbO2修饰玻碳电极.在Pb(NO3)2溶液中,在-0.7 V 将Pb膜沉积在玻碳电极表面,然后在5 mol/L NaOH溶液中以100 mV/s速度在-1.0～1.0 V循环伏安扫描20次,PbO2膜均匀沉积在玻碳电极表面.采用交流阻抗法监控电极修饰每一过程,环境扫描电镜表征电极表面形貌.探讨了PbO2膜的沉积机理及其电化学行为,表面活性位点覆盖量为7.5×10-10 mol/cm2.PbO2修饰电极对H2O2电氧化表现出较高催化活性,起始氧化电位低至0.1 V,考察了影响催化活性的因素.计时电流法测定H2O2 (工作电位0.40 V),响应时间小于2 s; 线性范围为5.0 ×10-6 ～ 5.5×10-4 mol/L;检出限1.1×10-6 mol/L (信噪比为3).在实际水样中H2O2测定结果满意.电极在室温环境下储存30 d,其催化活性基本不变.该修饰电极制备工艺简单、重现性良好、稳定性高.     

在Pt/CNTs催化层中预混-溶解La2O3颗粒来构筑孔结构促进甲醇电氧化

为认识孔隙度增加对甲醇电氧化的影响, 将熔盐法制备的La2O3颗粒与Pt/CNTs(碳纳米管)预混合然后用HClO4溶掉La2O3颗粒, 从而增加了Pt/CNTs催化层的孔隙度. 扫描电子显微镜(SEM)观察表明, 该处理可以形成孔结构. 用循环伏安和计时电流实验考察了孔隙度增加对甲醇电氧化的影响, 结果表明甲醇电氧化电流可增加57%. 分析认为, 电流增加的原因是由于多孔催化层中甲醇更易于到达Pt催化剂表面进行电氧化. 该研究表明, 通过在催化层中预混-溶解La2O3来增加孔隙是一种改善催化层性能的有效方法.     

在Pt/CNTs催化层中预混-溶解La2O3颗粒来构筑孔结构促进甲醇电氧化

为认识孔隙度增加对甲醇电氧化的影响,将熔盐法制备的La2O3颗粒与Pt/CNTs(碳纳米管)预混合然后用HClO4溶掉La2O3颗粒,从而增加了Pt/CNTs催化层的孔隙度.扫描电子显微镜(SEM)观察表明,该处理可以形成孔结构.用循环伏安和计时电流实验考察了孔隙度增加对甲醇电氧化的影响,结果表明甲醇电氧化电流可增加57%.分析认为,电流增加的原因是由于多孔催化层中甲醇更易于到达Pt催化剂表面进行电氧化.该研究表明,通过在催化层中预混-溶解La2O3来增加孔隙是一种改善催化层性能的有效方法.     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Separation of Tl/III/ from Tl/I/

A method for the separation of Tl/III/from Tl/I/ is reported employing 1-/2-pyridylazo/-2-naphthol /PAN/ and Rhodamine-B as extracting agents.     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.     

Analysis of nonvalent interactions in the crystals of conformational polymorphs of the composition CaHbNcOdSe by means of molecular voronoi-dirichlet polyhedra

Nonvalent interactions in crystals of compounds of the composition C _a H _b N _c O _d S _e that exhibit conformational polymorphism and have no fewer than four structurally characterized modifications are analyzed using molecular Voronoi-Dirichlet polyhedrals. A unique combination of the types of occurring intra- and intermolecular nonvalent contacts is shown to correspond to each conformational polymorph. Nonvalent interactions involving hydrogen atoms are found to occur most often in crystal structures, and least often those involving S, N, and O atoms.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

橙红色荧光粉Ca_(1-x-y)Sm_xBi_ySiO_3的制备及其发光性能

以Sm3+作为激活剂,Bi3+作为辅助激活剂,采用水热法合成Ca1-x-ySmxBiySi O3前驱体,然后在1 100℃焙烧得到系列橙红色荧光粉。用X-射线衍射仪、扫描电镜和荧光分光光度计和傅里叶变换红外光谱等手段对样品的组成、结构和形貌及其发光性质进行分析和表征。分析结果表明:产物都为三斜晶系结构的Ca1-x-ySmxBiySi O3和四方结构的方石英Si O2共熔体。在405 nm近紫外光激发下,产物的发射光谱由3个峰组成,发射峰值位于566、606和650 nm处,分别归属于Sm3+的4G5/2→6HJ/2(J=5,7,9)跃迁。产物的激发光谱在405 nm有很强的发射带,与近紫外LED芯片匹配。随着Sm3+掺量的增加,样品发光强度先增强后减弱,当Sm3+的物质的量分数为3%时发光强度达到最大,浓度猝灭机理为电偶极-电偶极相互作用。当Bi3+的物质的量分数在0.3%~1.5%时,对产物Ca0.97Sm0.03Si O3的荧光强度起敏化作用。Sm3+和Bi3+的最佳物质的量分数分别为3%和0.5%。     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

Rate of reactions between D2O and CaxAlyOz

The rate of the reaction between D₂O and the calcium aluminum oxides Ca₃Al₂O₆, Ca₅Al₆O₁₄, CaAl₂O₄, and CaAl₄O₇ was investigated by on-line neutron diffraction powder methods at temperatures from room temperature to 100°C. The rate of the reaction increases with increasing calcium content of the compounds and with increasing temperature for each of the compounds. The crystallographic stable hydrate Ca₃Al₂(OD)₁₂ is obtained from CaAl₄O₇ and CaAl₂O₄ at temperatures above 63°C, from Ca₅Al₆O₁₄ at temperatures above 49°C, and from Ca₃Al₂O₆ at temperatures as low as 7°C.